INDESIT LWC 71453 W UK User Manual

Instructions for use

WASHING MACHINE

GB

English,1

LWC 71453

Contents

Installation, 2-3-4-5

Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data

Care and maintenance, 6

Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose

Precautions and tips, 7

General safety
Disposal

Description of the washing machine
and starting a wash cycle, 8-9

Control panel
Indicator lights
Starting a wash cycle

GB

Wash cycles, 10

Table of wash cycles
Quick cycles

Personalisation, 11

Setting the temperature
Setting the spin speed
Functions

Detergents and laundry, 12

Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Load balancing system

Troubleshooting, 13-14

Product Guarantee and Repair Informa­tion, 15

1

Installation

GB

! Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washing machine to
inform the new owner as to its operation and
features.
! Read these instructions carefully: they contain
vital information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the washing machine.

2. Check whether the washing machine has
been damaged during transport. If this is the
case, do not install it and contact your retailer.

3. Remove the 3 pro­tective screws and the
rubber bush with the
respective spacer, si­tuated on the rear of the
appliance (see also the

installation leaflet).

Connecting the electricity and wa­ter supplies

Connecting the water inlet hose

1. Connect the supply
pipe by screwing it to
a cold water tap using
a 3/4 gas thre aded
connection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.

2. Connect the other
end of the water inlet
hose to the washing
machine, screwing it
onto the appliance’s
cold water inlet, situated
on the top right-hand
side on the rear of the
appliance (see figure).

4. Seal the gaps using the plastic plugs provided.

5. Keep all the parts: you will need them again
if the washing machine needs to be moved to
another location.
! Packaging materials are not children’s toys.

Levelling

Your machine may make a considerable amount
of noise if the two front feet have not been adju­sted correctly.

1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furniture
cabinets or other.

2. If the floor is not per­fectly level, compensate
for any unevenness by
tightening or loosening
the adjustable front feet
(see figure); the angle
of inclination, measu­red according to the
worktop, must not ex­ceed 2°.

Levelling your appliance correctly will provide it
with stability and avoid any vibrations, noise and
shifting during operation. If it is placed on a fitted
or loose carpet, adjust the feet in such a way as
to allow enough room for ventilation beneath the
washing machine.

3. Make sure there are no kinks or bends in the
hose.

! The water pressure at the tap must be within

the values indicated in the Technical details
table (see page 5).

! If the water inlet hose is not long enough,

contact a specialist store or an authorised
serviceman.

! Ensure that the supply taps are allowing wa-

ter through. Old taps may seize in the closed
position and thus prevent water reaching the
machine.

2

Connecting the drain hose

65 - 100 cm

Where it connects to
the waste water pipe
cut end off spigot or
remove the blanking cap

Con n ect t h e dr a in
hose, without bending
it, to a draining duct or
a wall drain situated
between 65 and 100
cm from the floor;

• the supply voltage is included within the values

indicated on the Technical Data Plate fixed on
the machine.

• the socket is compatible with the washing

machine’s plug. If this is not the case, replace
the socket or the plug.

Your appliance is now supplied with a 13 amp fu­sed plug it can be plugged into a 13 amp socket
for immediate use. Before using the appliance
please read the instructions below.

GB

The drain hose may
be connected to an
under-sink trap. Be­fore connecting the
drain hose from the
machine ensure that
any blanks or remo­vable ends have been
taken off the spigot.

If it is placed over the
edge of a basin or sink
be sure the free end of
the hose should not
be underwater.

! We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length. Ensure that if the drain
hose is pushed into a standpipe, that the end does
not go down more than 15cms (6 inches). If the hose
is pushed down too far, this may cause the machine
to self -syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains
socket, make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated on the Technical
Data Plate fixed on the machine;

WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be
used, and the fuse cover re-fitted. If the fuse
cover is lost, the plug must not be used until a
replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words
on the base of the plug. Replacements can be
obtained directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded
plug and you should wish to re-route the mains
cable through partitions, units etc., please en­sure that either:
the plug is replaced by a fused 13 ampere rewi­reable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp
cable outlet, controlled by a switch, (in complian­ce with BS 5733) which is accessible without
moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,
you make the pins unusable so that it cannot be
accidentally inserted into a socket.

Instructions for connecting cable to an alterna­tive plug:
Important: the wires in the mains lead are co­loured in accordance with the following code:

Green & Yellow Earth
Blue Neutral
Brown Live

3

GB

GREEN &
YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR
CORD GRIP

As the colours of the wires in the lead may not
correspond with the coloured markings iden­tifying the terminals in your plug, proceed as
follows:
Connect Green & Yellow wire to terminal
marked E or or coloured Green or Green &
Yellow.
Connect Brown wire to terminal marked L or
coloured Red.
Connect Blue wire to terminal marked N or co­loured Black.
If a 13 amp plug (BS 1363) is used it must be
fitted with a 13 amp fuse, either in the plug or
adaptor or at the distribution board.
If you are in any doubt regarding the electrical
supply to your machine, consult a qualified
electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:

BLUE NEUTRAL (N)
BROWN LIVE (L)
GREEN & YELLOW EARTH (E)

! The power supply cable must only be repla-
ced by an authorised serviceman.

Warning! The company denies all liability if and
when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle 8.

Technical data

Model

Dimensions

Capacity

Electrical
connections

LWC 71453

width 59.5 cm
height 85 cm
depth 51.7 cm

from 1 to 7 kg

please refer to the technical
data plate fixed to the machine

Disposing of the appliance:

When disposing of the appliance please re­move the plug by cutting the mains cable as
close as possible to the plug body and dispo­se of it as described above.

! The washing machine should not be installed
in an outdoor environment, not even where
the area is sheltered, because it may be very
dangerous to leave it exposed to damp, rain
and thunderstorms.

! When the washing machine is installed, the
mains socket must be within easy reach.

! Do not use extensions or multiple sockets.

Water
connection

Spin speed

Test wash
cycles in
accordance
with re­gulations
1061/2010
and
1015/2010

maximum pressure
1 MPa (10 bar)
minimum pressure

0.05 MPa (0.5 bar)
drum capacity 46 litres

up to 1400 rotations per minute

Programme 4:
Eco Cotton 60°.
Programme 4:
Eco Cotton 40°.

This appliance conforms to
the following EC Directives:

- 2004/108/EC (Electroma­gnetic Compatibility)

- 2012/19/EU - WEEE

- 2006/95/EC Low Voltage)

! The power supply cable must never be bent
or dangerously compressed.

4

GB

5

Care and maintenance

GB

Cutting off the water and electri­city supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system
inside the washing machine and help to pre­vent leaks.

• Unplug the washing machine when cleaning

it and during all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.

Cleaning the detergent dispenser
drawer

Remove the dispenser
by raising it and pul­ling it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.

1. using a screwdri­ver, remove the cover
panel on the lower
front part of the wa­shing machine (see
figure);

2. unscrew the lid
by rotating it anti­clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.

Caring for the door and drum of
your appliance

• Always leave the porthole door ajar in order

to prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-clea­ning pump which does not require any mainte­nance. Sometimes, small items (such as coins
or buttons) may fall into the pre-chamber which
protects the pump, situated in its bottom part.

! Make sure the wash cycle has finished and
unplug the appliance.

To access the pre-chamber:

Checking the water inlet hose

Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.

! Never use second-hand hoses.

6

Precautions and tips

! This washing machine was designed and constructed in

accordance with international safety regulations. The fol­lowing information is provided for safety reasons and must
therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children aged

from 8 years and above and persons with re­duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.

• The washing machine must only be used by adults, in accor­dance with the instructions provided in this manual.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug and
pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extremely

high temperatures.

• Never force the porthole door. This could damage the safety

lock mechanism designed to prevent accidental opening.

• If the appliance breaks down, do not under any circum­stances access the internal mechanisms in an attempt to
repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

The crossed out “wheeled bin” symbol on the product

reminds you of your obligation, that when you dispose of
the appliance it must be separately collected. Consumers
should contact their local authority or retailer for information
concerning the correct disposal of their old appliance.

GB

Disposal

• Disposing of the packaging materials: observe local regu­lations so that the packaging may be re-used.

• The European Directive 2012/19/EU (WEEE) on Waste Elec­trical and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must
be collected separately in order to optimise the recovery
and recycling of the materials they contain and reduce the
impact on human health and the environment.

7

Description of the washing
machine and starting a wash cycle

GB

Control panel

Detergent dispenser drawer

ON/OFF

WASH CYCLE

button

knob

TEMPERATURE

knob

WASH CYCLE PROGRESS/
DELAY TIMER indicator lights

FUNCTION

butto ns with
indicator lights

SPIN SPEED

knob

START/
PAUSE

button with
indicator light

DOOR LOCKED

indicator light

Detergent dispenser drawer: used to dispense deter­gents and washing additives (see “Detergents and laundry”).

ON/OFF button: switches the washing machine on and off.

WASH CYCLE knob: programmes the wash cycles. During

the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.

TEMPERATURE knob: sets the temperature or the cold
wash cycle (see “Personalisation”).

SPIN SPEED knob: sets the spin speed or exclude the spin
cycle completely (see “Personalisation”).

WASH CYCLE PROGRESS/DELAY TIMER

light

s: used to monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in pro­gress.
If the Delay Timer function has been set, the time remaining
until the wash cycle starts will be indicated (see next page).

indicator

START/PAUSE button with indicator light: starts or tempo­rarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this button;
the corresponding indicator light will flash orange, while the
indicator light for the current wash cycle phase will remain lit
in a fixed manner. If the DOOR LOCKED indicator light is
switched off, the door may be opened (wait approximately
3 minutes).
To start the wash cycle from the point at which it was inter­rupted, press this button again.

Standby mode

This washing machine, in compliance with new energy saving
regulations, is fitted with an automatic standby system which
is enabled after about 30 minutes if no activity is detected.
Press the ON-OFF button briefly and wait for the machine
to start up again.

DOOR LOCKED indicator light: indicates whether the door
may be opened or not (see next page).

8

Indicator lights

The indicator lights provide important information.
This is what they can tell you:

Delayed start

If the DELAY TIMER function has been activated (see “Per­sonalisation”), after the wash cycle has been started the

indicator light corresponding to the selected delay period
will begin to flash:

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has be­gun, the indicator lights switch on one by one to indicate which
phase of the cycle is currently in progress.

Wash

Rinse

Spin

Drain

GB

As time passes, the remaining delay will be displayed and
the corresponding indicator light will flash:

The set programme will start once the selected time delay
has expired.

End of wash cycle

Function buttons and corresponding indicator lights

When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the program­med wash cycle, the corresponding indicator light will flash
and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the indicator
light corresponding to the first function selected will
flash and only the second function will be activated; the

indicator light corresponding to the enabled option will
remain lit.

Door locked indicator light

When the indicator light is on, the porthole door is locked
to prevent it from being opened; make sure the indicator
light is off before opening the door (wait approximately 3
minutes). To open the door during a running wash cycle,
press the START/PAUSE button; the door may be opened
once the DOOR LOCKED indicator light turns off.

END

Starting a wash cycle

1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then
they will switch off and the START/PAUSE indicator light will pulse.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see “Personalisation”).

5. Set the spin speed (see “Personalisation”).

6. Measure out the detergent and washing additives (see “Detergents and laundry”).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed

manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9. At the end of the wash cycle the indicator light will switch on. The door can be opened once the DOOR LOCKED
indicator light turns off (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar to make sure
the drum dries completely. Switch the washing machine off by pressing the ON/OFF button.

9

Wash cycles

GB

Table of wash cycles

Description of the wash cycle

Wash cycles

Everyday

1

Cotton: lightly soiled whites and delicate colours.

2

Synthetic (3): lightly soiled resistant colours.

3

Wool: for wool, cashmere, etc. 40° 800

4

Eco Cotton 60° (1): heavily soiled whites and resistant colours. 60° 1400

4

Eco Cotton 40° (2): lightly soiled whites and delicate colours. 40° 1400

Inside

5

Baby: Heavily soiled delicate colours. 40° 800

6

Silk/Curtains: for garments in silk and viscose, lingerie.

7

Duvet: for down-stuffed garments. 30° 1000

8

Sanitary: Extremely soiled whites. 90° 1400
Outside

9 Sport Kit

10 Sport Shoes

11 Technical Wear

Quick
12 Mixed 59’
13 Mixed 30’
14 Refresh 20’

Rinse - 1400 -

Spin + Drain - 1400 - - 7 - - - 10’

Drain only * - - - 7 - - - 3’

Max.

temp. (°C)

40°

(Max.90°)

40°

(Max.60°)

30° 0

40° 600

30° 600

30° 600

40° 1000
30° 800
20° 800

Max.

speed

(rpm)

1400

1000

Detergents

Wash

 

 

 
 
 

 
 
 
 

 

 

 

 
 
 

Fabric

softener



Max.

load (kg)

7 - - - 125’

3 44 0.49 38 100’

1.5 - - - 80’
7 53 0.99 52.4 210’
7 53 0.88 70 205’

2 - - - 85’
1 - - - 55’

1.5 - - - 100’

7 - - - 195’

3 - - - 85’

Max.

2

pairs

3 - - - 65’

7 - - - 59’

3.5 70 0.17 31 30’

3.5 - - - 20’
7 - - - 49’

Energy

Residual

dampness %

consumption

- - - 55’

kWh

Total water lt

Cycle

duration

* If you select programme and exclude the spin cycle, the machine will drain only.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water
temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

1) Test wash cycle in compliance with regulation 1061/2010: set wash cycle 4 with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at
60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with regulation 1061/2010: set wash cycle 4 with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at
40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.

3) Synthetic program along: set wash cycle 2 with a temperature of 40°C.

Quick cycles

Mixed 59’: to wash mixed and coloured items together.
Mixed 30’: short cycle designed to wash a mixed load of cotton and synthetic fabrics - white and coloured items together.
Refresh 20’: this programme refreshes your items, making them perfumed again in just 20 minutes.

10

Personalisation

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash .
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value
set for each wash cycle.

! Exception: if the 1 programme is selected, the temperature can be increased up to a value of 90°C.
! Exception: if the 2 programme is selected, the temperature can be increased up to a value of 60°C.

Setting the spin speed

Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:

Wash cycles Maximum spin speed

Cottons 1400 rpm
Synthetics 1000 rpm
Wool 800 rpm
Silk drain only

The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.

Functions

The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note:

- If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and
the function will not be activated.

- If the selected function is not compatible with another function which has been selected previously, the indicator light
corresponding to the first function selected will flash and only the second function will be activated; the indicator light

corresponding to the enabled option will remain lit.

GB

Eco Cool

The Eco Cool option washes cotton and synthetic items, saving energy and helping the environment. Energy saving is due to
a cold wash cycle, while an enhanced mechanical action and optimised water use make it possible to reach the desired result.

Recommended for slightly soiled garments. Use of liquid detergent recommended.

Easy Iron

By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At the end
of the cycle the washing machine will perform slow rotations of the drum; the indicator lights for the EASY IRON and START/
PAUSE options will flash (the first one green, the second orange). To end the cycle, press the START/PAUSE button or the
EASY IRON button. For the Silk wash cycles, the machine will end the cycle while the laundry is soaking and the EASY IRON
and START/PAUSE indicator lights will flash and the RINSE phase will remain lit in a fixed manner. To drain the water so that
the laundry may be removed, press the START/PAUSE button or the EASY IRON button.

Extra Rinse

By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.

Delay timer

This timer delays the start time of the wash cycle by up to 12 hours.
Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button
is pressed, the function will be disabled.
N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching
the set programme.

11

Detergents and laundry

1

2

3

GB

Detergent dispenser drawer

Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessarily
result in a more efficient wash, and may in fact cause build
up on the inside of your appliance and contribute to envi­ronmental pollution.

! Do not use hand washing detergents because these create

too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent dispen­ser drawer and pour in the
detergent or washing additi­ve, as follows.

! Do not put the detergent into compartment 1.
! The detergent must be put only in the compartment 2.

compartment 2: Detergent for the wash cycle
(powder or liquid)

Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.
Note: If a “tablet detergent” is used, always follow the

manufacturer’s instructions.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g

Garments requiring special care

Wool: all wool garments can be washed using programme
3, even those carrying the “hand-wash only” label. For

best results, use special detergents and do not exceed 1.5
kg of laundry.
Baby: cycle designed for dirt typical of children’s garments
in that it effectively removes any traces of residual detergent.
Silk: use special wash cycle 6 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.

Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 6.
Duvet: to wash single duvets (the weight of which should not
exceed 1.5 kg), cushions or clothes padded with goose down
such as puffa jackets, use the special wash cycle number 7.
We recommend that duvets are placed in the drum with their
edges folded inwards (see figure) and that no more than ¾
of the total volume of the drum is used. To achieve the best
results, we recommend that a liquid detergent is used and
placed inside the detergent dispenser drawer.

Sanitary (wash cycle 8). A high-temperature hygienic wash
cycle (over 60°C) for extremely soiled whites.
Sport Kit: a cycle designed to simultaneously wash any type
of sports clothing together with gym towels (Temperature
40°).
Sport Shoes: is for washing sports shoes; for best results,
do not wash more than 2 pairs simultaneously.
We recommend fastening any strings before introducing the
shoes into the drum.
Technical Wear: designed for specifically washing water­proof garments or clothing with special technical fibres like
Gore-Tex, so as to optimise washing performance while
preserving their technical properties over time. Do not use
fabric softeners for garments with technical fibres.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.

12

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be solved easily using the following list.

Problem:

The machine does not switch on.

The wash cycle does not start.

The machine does not fill with wa­ter or the indicator light for the first
wash cycle stage flashes rapidly.

The machine continuously fills with
water and continually drains away
or Water left in the drum
or Stuck on wash.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make contact.

• There is no power to the socket, or the fuse has blown in the mains plug.

• The door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been turned on to allow water to flow into the machine.

• A delayed start has been set.

• The water inlet hose is kinked.

• The water inlet hose is not connected to the water supply.

• The water pressure is too low.

• The water tap has not been turned on to allow water to flow into the machine.

• There is no water supply to the house.

• The inlet valve filter is blocked.

• The START/PAUSE button has not been pressed.

• The top of the drain hose is too low - It must be fitted at a height between 65

and 100 cm from the floor (see “Installation”).

• The drain hose is connected incorrectly to the sink trap allowing water to run

into the machine, the drain hose must be positioned higher than the bottom of
the sink to prevent water flowing down the drain hose.

• The end of the drain hose has been pushed too far down the standpipe, the

‘U’ bracket should be fitted 100 mm from the end of the drain hose.

GB

The machine does not drain or
spin.

The machine does not heat or poor
wash results.

The programme takes too long.

The machine vibrates a lot during
the spin cycle.

• The Pump filter is blocked.

• The drain hose is kinked (see “Installation”).

• New Installation - The blanking cap or spigot has not been removed if

connected under a sink.

• The drain hose or sink trap is blocked.

• The wash cycle does not include draining, some wash cycles require the drain

phase to be started manually.

• The ‘Spin Speed’ selector knob is in the position.

• The ‘Temperature’ selector knob is in the “ ” position.

• Programme times will vary due to water pressure, the incoming water tempera-

ture and if the wash load goes out of balance. This will increase the programme
times accordingly (see ‘ The machine wont spin properly’ next page).

• The feet have not been adjusted, enabling the machine to rock.

• New Installation - Either the Transit Bolts including the plastic spacers, or the

Polystyrene Packaging have not been removed when installing the machine.

• The machine is trapped between cabinets and/or walls.

• The load is in a slight out of balance condition and machine is spinning, but at

a lower speed.

13

GB

The machine is noisy.

The machine wont spin properly.

• There will always be some motor, pump and drum noise during spin.

• Out of Balance detected when attempting to go into a spin cycle - If this

happens the machine will continue to try to repeat the distribution of the load
required before the machine will go into higher spin speeds - This will increase
the programme time accordingly. This is a safety feature to prevent damage.
Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,
etc). - Try the programme again using a different load.

The machine leaks from the
dispenser.

The machine leaks (other than
dispenser).

The indicator lights on the console
are flashing rapidly.

The machine smells.

The machine door cannot be
opened.

Door Seal damaged at the bottom.

The water level is too low when
the machine is washing.

• The dispenser drawer is blocked with detergent and requires cleaning.

• The water pressure is too high and requires turning down - turn down the tap

on the water supply pipe slightly and try again.

• The machine is tilting forwards - It must be level when in its final position.

• The fill hose is loose, check both the cabinet and tap ends.

• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill

hose is missing the rubber washer.

• The drain hose is not fixed in properly.

• Switch off the machine and unplug it, wait for approximately 1 minute and then

switch it back on again If the problem persists contact the Technical Assistance
Service.

• The machine requires a service wash. Run a 90 degree wash cycle with deter­gent and no laundry.

• The door will not open until the door lock indicator light goes out shortly after

the program has finished.

• The door seal has drainage holes at the bottom - This is normal.

• The water level is correct if it can be seen at the bottom of the door.

There is too much foam.

After completing the programme,
or before starting a programme,
the machine has turned itself off
(no lights).

General.

Remember, you will be charged for a service call for problems caused by incorrect installation, as indica­ted on pages 2 to 4.
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.
Do not wash items which do not have a wash label, or wash items that are not intended as machine wa­shable.

14

• The detergent is not suitable for machine washing (it should display the text
‘for washing machines’ or ‘hand and machine wash’ or the like).

• Too much detergent was used - less detergent is required in soft water.

• To comply with new energy saving regulations the machine is fitted with an

automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate
the machine, it can then either be switched off or a new programme selected.

• Your washing machine contains sensors that monitor progress during the wash

cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/pro­gress).

Normally, if your machine successfully completes the cycle, there is unlikely to

be anything wrong!

Product Guarantee and
Repair Information

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s
guarantee, which covers the cost of breakdown
repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that
time, your appliance is proven to be defective
because of either workmanship or materials, we will,
at our discretion, either repair or replace the appliance
at no cost to you:
This guarantee is subject to the following conditions:

- The appliance has been installed and operated
correctly and in accordance with our operating and
maintenance instructions.

- The appliance is used only on the electricity or gas
supply printed on the rating plate.

- The appliance has been used for normal domestic
purposes only.

- The appliance has not been altered, serviced,
maintained, dismantled, or otherwise interfered with
by any person not authorised by us.

- Any repair work must be undertaken by us or our
appointed agent.

- Any parts removed during repair work or any
appliance that is replaced become our property.

- The appliance is used in the United Kingdom or
Republic of Ireland.
The guarantee does not cover:

- Damage resulting from transportation, improper
use, neglect or interference or as a result of improper
installation.

- Replacement of any consumable item or accessory.
These include but are not limited to: plugs, cables,
batteries, light bulbs, fluorescent tubes and starters,
covers and filters.

- Replacement of any removable parts made of glass
or plastic.

Recycling and Disposal Information

As part of Indesit’s continued commitment to
helping the environment, Indesit reserves the right
to use quality, recycled components to keep down
customer costs and minimise material wastage.
Please dispose of packaging and old appliances
carefully. To minimise the risk of injury to children,
remove the door, plug, and cut the mains cable
off flush with the appliance. Dispose of these parts
separately to ensure that the appliance can no longer
be plugged into mains socket, and the door cannot
be locked shut.

Repairs and After Sales

For product help and advice, repairs, spare parts or
accessories, we’re here to help.

For local repair engineers - 03448 111 606
ROI - 0818 313 413

UK standard local rate applies
ROI local Irish rate applies

For Parts and Accessories visit:

parts.indesit.co.uk/shop

Please remember to register your appliance at
www.indesitservice.co.uk to activate your 10 year
parts guarantee.

How to find your model and serial number:

GB

THIS GUARANTEE WILL NOT APPLY IF THE
APPLIANCE HAS BEEN USED IN COMMERCIAL
OR NON-DOMESTIC PREMISES.

15

GB

195142217.00

02/2016

İthalatçı Firma:
Indesit Company Beyaz Eşya PAZARLAMA A.Ş.
Balmumcu Cad. Karahasan Sok.
No: 11, 34349 – Balmumcu Beşiktaş – İstanbul
Tel: [phone]

16