Indesit IWSE 61051 Instructions For Use Manual

1

GB

Contents

Installation, 2-3

Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data

Care and maintenance, 4

Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose

Precautions and tips, 5

General safety
Disposal
Opening the porthole door manually

Description of the washing machine, 6-7

Control panel
Display

Running a wash cycle, 8

Wash cycles and options, 9

Table of wash cycles
Wash options

Detergents and laundry, 10

Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system

Troubleshooting, 11

Service, 12

IWSE 61051

Instructions for use

WASHING MACHINE

English,1

GB

Český,37

CZ

GR

Ελληνικά, 25

Hrvatski,13

HR

Українська,49

UK

2

GB

! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.

! Read these instructions carefully: they contain
vital information relating to the safe installation
and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging.

2. Make sure that the washing machine has not
been damaged during the transportation process.
If it has been damaged, contact the retailer and do
not proceed any further with the installation process.

3. Remove the 4 pro­tective screws (used
during transportation)
and the rubber washer
with the corresponding
spacer, located on the
rear part of the applian­ce (see figure).

4. Close off the holes using the plastic plugs
provided.

5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.

! Packaging materials should not be used as
toys for children.

Levelling

1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furniture
cabinets or anything else.

2. If the floor is not per­fectly level, compensa­te for any unevenness
by tightening or loo­sening the adjustable
front feet (see figure);
the angle of inclination,
measured in relation to
the worktop, must not
exceed 2°.

Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive
noise and prevent it from shifting while it is ope­rating. If it is placed on carpet or a rug, adjust the
feet in such a way as to allow a sufficient venti­lation space underneath the washing machine.

Connecting the electricity and wa­ter supplies

Connecting the water inlet hose

1. Connect the supply
pipe by screwing it to
a cold water tap using
a ¾ gas threaded con­nection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.

2. Connect the inlet
hose to the washing
machine by screwing
it onto the correspon­ding water inlet of the
appliance, which is si­tuated on the top right­hand side of the rear
part of the appliance
(see figure).

3. Make sure that the hose is not folded over
or bent.

! The water pressure at the tap must fall within
the values indicated in the Technical details table

(see next page).

! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Installation

3

GB

65 - 100 cm

Connecting the drain hose

Co n nect the d rain
hose, without bending
it, to a drainage duct or
a wall drain located at a
height between 65 and
100 cm from the floor;

alternatively, rest it on
the side of a washba­sin or bathtub, faste­ning the duct supplied
to the tap (see figure).
The free end of the
hose should not be
underwater.

! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity
socket, make sure that:

• the socket is earthed and complies with all
applicable laws;

• the socket is able to withstand the maximum
power load of the appliance as indicated in the
Technical data table (see opposite);

• the power supply voltage falls within the values
indicated in the Technical data table (see opposite);

• the socket is compatible with the plug of the
washing machine. If this is not the case, repla­ce the socket or the plug.

! The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.

! When the washing machine has been installed,
the electricity socket must be within easy reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be replaced

by authorised technicians.

Warning! The company shall not be held responsible
in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle 2.

Technical data

Model

IWSE 61051

Dimensions

width 59.5 cm
height 85 cm
depth 42 cm

Capacity

from 1 to 6 kg

Electrical
connections

please refer to the technical
data plate fixed to the machine

Water
connection

maximum pressure
1 MPa (10 bar)
minimum pressure

0.05 MPa (0.5 bar)
drum capacity 40 litres

Spin speed

up to 1000 rotations per minute

Test wash
cycles in
accordan­ce with
directives
1061/2010
and
1015/2010

Programme 2:
Cotton standard 60°C.
Programme 3:
Cotton standard 40°C.

This appliance conforms to
the following EC Directives:

- 2004/108/EC dated
03/05/89 (Electromagnetic
Compatibility)

- 2002/96/EC

- 2006/95/EC Low Voltage)

4

GB

Care and maintenance

Cutting off the water and electri­city supplies

• Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system
inside the washing machine and help to pre­vent leaks.

• Unplug the washing machine when cleaning
it and during all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.

Cleaning the detergent dispenser
drawer

Remove the dispenser
by raising it and pul­ling it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.

Caring for the door and drum of
your appliance

• Always leave the porthole door ajar in order
to prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-clea­ning pump which does not require any mainte­nance. Sometimes, small items (such as coins
or buttons) may fall into the pre-chamber which
protects the pump, situated in its bottom part.

! Make sure the wash cycle has finished and
unplug the appliance.

To access the pre-chamber:

1. using a screwdri­ver, remove the cover
panel on the lower
front part of the wa­shing machine (see
figure);

2. unscrew the lid
by rotating it anti­clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.

! Never use second-hand hoses.

5

GB

Precautions and tips

! This washing machine was designed and constructed in

accordance with international safety regulations. The fol­lowing information is provided for safety reasons and must
therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children aged
from 8 years and above and persons with re­duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning
and user maintenance shall not be made by
children without supervision.

• The washing machine must only be used by adults, in accor­dance with the instructions provided in this manual.

• Do not touch the machine when barefoot or with wet or
damp hands or feet.

• Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug and
pull.

• Do not open the detergent dispenser drawer while the
machine is in operation.

• Do not touch the drained water as it may reach extremely
high temperatures.

• Never force the porthole door. This could damage the safety
lock mechanism designed to prevent accidental opening.

• If the appliance breaks down, do not under any circum­stances access the internal mechanisms in an attempt to
repair it yourself.

• Always keep children well away from the appliance while
it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make
sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local regu­lations so that the packaging may be re-used.

• The European Directive 2002/96/EC on Waste Electrical and
Electronic Equipment, requires that old household electrical
appliances must not be disposed of in the normal unsorted
municipal waste stream. Old appliances must be collected
separately in order to optimise the recovery and recycling
of the materials they contain and reduce the impact on
human health and the environment.

Opening the porthole door manually

In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:

1. remove the plug from the
electrical socket.

2. make sure the water level
inside the machine is lower
than the door opening; if it
is not, remove excess water
using the drain hose, collec­ting it in a bucket as indicated
in the figure.

3. using a screwdriver, remo­ve the cover panel on the lo­wer front part of the washing
machine (see figure).

4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.

5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.

The crossed out “wheeled bin” symbol on the product

reminds you of your obligation, that when you dispose of
the appliance it must be separately collected. Consumers
should contact their local authority or retailer for information
concerning the correct disposal of their old appliance.

6

GB

Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).

ON/OFF button : press this briefly to switch the ma­chine on or off. The START/PAUSE indicator light, which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 2
seconds; if the button is pressed briefly or accidentally the
machine will not switch off. If the machine is switched off
during a wash cycle, this wash cycle will be cancelled.

WASH CYCLE knob: used to set the desired wash cycle

(see “Table of wash cycles”).

OPTION buttons with indicator light: used to select the
available options. The indicator light corresponding to the
selected option will remain lit.

SPIN button : press to reduce or completely exclude
the spin cycle - the value is indicated on the display.

TEMPERATURE button : press to decrease or comple­tely exclude the temperature: the value will be shown on
the display.

DELAYED START button : press to set a delayed start
time for the selected wash cycle. The delay time will be
shown on the display.

START/PAUSE button with indicator light: when the
green indicator light flashes slowly, press the button to
start a wash cycle. Once the cycle has begun the indicator
light will remain lit in a fixed manner. To pause the wash
cycle, press the button again; the indicator light will flash
in an orange colour. If the symbol is not illuminated, the
door may be opened. To start the wash cycle from the
point at which it was interrupted, press the button again.

Standby mode

This washing machine, in compliance with new energy sa­ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.

Consumption in off-mode: 0,5 W
Consumption in Left-on: 0,5 W

Description of the washing
machine

Control panel

TEMPERATURE

Button

Detergent dispenser drawer

OPTION

buttons with
indicator lights

ON/OFF

button

SPIN SPEED

Button

START/PAUSE

button with indicator light

DISPLAY

DELAYED
START Button

WASH CYCLE

knob

7

GB

Display

The display is useful when programming the machine and provides a great deal of information.

The duration of the available programmes and the remaining time of a running cycle appear in section A; if the DELAY START
option has been set, the countdown to the start of the selected programme will appear. Pressing the relative button, the
machine automatically displays the maximum temperature and spin speed values set for the selected cycle, or the most
recently-used settings if they are compatible with the selected cycle.

The “programme phases” relative to the selected programme and the “programme phase” of the running programme appear
in section B:

Wash

Rinse
Spin
Drain

The icons corresponding to “temperature” , “Programmed start” and “spin” appear in section C from top to bottom:
If the symbol lights up, the display will visualise the set “temperature” value.
When a “delayed start” has been set, the symbol lights up.
If the symbol lights up, the display will visualise the set “spin” value.

Door locked symbol
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the
door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened.

B

CA

8

GB

Running a wash cycle

1. SWITCH THE MACHINE ON. Press the button;

the START/PAUSE indicator light will flash slowly in a
green colour.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes on the following page.

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents

and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Set the WASH CYCLE

knob to the desired programme; a temperature and spin
speed is set for each wash cycle; these may be adjusted.
The duration of the cycle will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

Modifying the temperature and/or spin

speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.

! Exception: if the 2 programme is selected, the

temperature can be increased up to a value of 90°C.

Setting a delayed start.

To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
option is enabled, the symbol lights up on the
display. To remove the delayed start option press the
button until the text “OFF” appears on the display.

Modifying the cycle settings.

• Press the button to enable the option; the indicator
light corresponding to the button will switch on.

• Press the button again to disable the option; the
indicator light will switch off.

! If the selected option is not compatible with the

programmed wash cycle, the indicator light will flash
and the option will not be activated.

! If the selected option is not compatible with another

option which has been selected previously, the indicator
light corresponding to the first option selected will flash
and only the second option will be activated; the indicator
light corresponding to the enabled option will remain lit.

! The options may affect the recommended load value

and/or the duration of the cycle.

7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light will
become green, remaining lit in a fixed manner, and the
door will be locked (the DOOR LOCKED symbol will
be on). To change a wash cycle while it is in progress,
pause the washing machine using the START/PAUSE
button (the START/PAUSE indicator light will flash
slowly in an orange colour); then select the desired
cycle and press the START/PAUSE button again.

To open the door while a cycle is in progress, press the

START/PAUSE button; if the DOOR LOCKED symbol
is switched off the door may be opened. Press the
START/PAUSE button again to restart the wash cycle
from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may be
opened. Open the door, unload the laundry and switch
off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped
and the machine will switch off.

9

GB

Wash cycles and options

Wash options

Selecting this option enables you to suitably adjust drum
rotation, temperature and water to a reduced load of lightly
soiled cotton and synthetic fabrics (refer to the “Programme
table”). “ ” enables you to wash in less time thereby
saving water and electricity. We suggest using a liquid
detergent suitably measured out to the load quantity.
! It cannot be used with the 1, 6, 7, 8, 9, 10, 11, 12, 13,
14, , programmes.

The function saves energy by not heating the
water used to wash your laundry - an advantage both to
the environment and to your energy bill. Instead, intensified
wash action and water optimisation ensure great wash
results in the same average time of a standard cycle.
For the best washing results we recommend the usage of
a liquid detergent.

! It cannot be used with the 1, 6, 7, 8, 9, 10, 12, 13, 14,

, programmes.

Table of wash cycles

Extra Rinse

By selecting this option, the efficiency of the rinse is
increased and optimal detergent removal is guaranteed. It
is particularly useful for sensitive skin.
! It cannot be used in conjunction with the 8,
programmes.

Easy Iron

By selecting this function, the wash and spin cycles will be
modified in order to reduce the formation of creases. At the
end of the cycle the washing machine will perform slow ro­tations of the drum; the indicator lights for the EASY IRON
and START/PAUSE options will flash (the first one green,
the second orange). To end the cycle, press the START/
PAUSE button or the EASY IRON button. For the 9 wash
cycle, the machine will end the cycle while the laundry is
soaking and the EASY IRON and START/PAUSE indicator
lights will flash. To drain the water so that the laundry may
be removed, press the START/PAUSE button or the EASY
IRON button.

! It cannot be used with the 8, 10, 12, 13, 14, ,

programmes.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as
water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 2 with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 3 with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.

3) Synthetic program along: set wash cycle 4 with a temperature of 40°C.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max.

load (kg)

Residual

dampness %

Energy

consum-

ption kWh

Total water lt

Cycle

duration

Pre-

wash

Wash

Fabric

softener

Daily

1

Cotton with prewash: extremely soiled whites.

90° 1000

  

6

6 1,81 65 150’

2

Cotton Standard 60° (1): heavily soiled whites and resistant colours.

60°

(Max. 90°)

1000 -

 

6

62 1,04 48 195’

3

Cotton Standard 40° (2): lightly soiled whites and delicate colours.

40° 1000 -

 

6

62 1,03 65 180’

4

Synthetics: heavily soiled resistant colours.

60° 800 -

 

3

44 0,70 40 105’

4

Synthetics (3): lightly soiled resistant colours.

40° 800 -

 

3

44 0,47 38 95’

5

Mix Colored: lightly soiled whites and delicate colours.

40° 1000 -

 

6

62 0,64 50 85’

20° Zone

6

Cotton Standard 20°: lightly soiled whites and delicate colours.

20° 1000 -

 

5

- - - 170’

7 Mix Light

20° 800 -

 

5

- - - 120’

8 20’ Refresh

20° 800 -

 

1,5

- - - 20’

Special

9

Silk/Curtains: for garments in silk and viscose, lingerie.

30° 0 -

 

1

- - - 55’

10

Wool: for wool, cashmere, etc.

40° 800 -

 

1

- - - 65’

11 Jeans

40° 800 -

 

2,5

- - - 70’

Sport

12 Sport Intensive

30° 600 -

 

2,5

- - - 85’

13 Sport Light

30° 600 -

 

2,5

- - - 60’

14 Sport Shoes

30° 600 -

 

Max. 2

Pairs

- - - 55’

Partial wash cycles

Rinse

- 1000 - -



6

- - - 36’

Spin + Drain

- 1000 - - - 6

- - - 16’

10

GB

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessarily
result in a more efficient wash, and may in fact cause build
up on the inside of your appliance and contribute to envi­ronmental pollution.

! Do not use hand washing detergents because these create

too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent dispen­ser drawer and pour in the
detergent or washing additi­ve, as follows.

compartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)

Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the values listed in the “Table of wash
cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g

Special wash cycles

Silk: use special wash cycle 9 to wash all silk garments.

We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 9.
Wool: all wool garments can be washed using programme
10, even those carrying the “hand-wash only” label. For
best results, use special detergents and do not exceed 1 kg
of laundry.
Jeans: Turn garments inside-out before washing and use
a liquid detergent. Use programme 11.

Sport Intensive (programma 12): is for washing heavily
soiled sports clothing fabrics (tracksuits, shorts, etc.); for
best results, we recommend not exceeding the maximum
load indicated in the “Programme table”.
Sport Light (programma 13): is for washing lightly soiled
sports clothing fabrics (tracksuits, shorts, etc.); for best
results, we recommend not exceeding the maximum load
indicated in the “Programme table”. We recommend using
a liquid detergent and dosage suitable for a half-load.
Sport Shoes (programma 14): is for washing sports shoes;
for best results, do not wash more than 2 pairs simulta­neously.

The 20° wash cycles (20° Zone) offer effective washing
performance at low temperatures, reducing electricity
usage and expenditure while benefitting the environment.
The 20° wash cycles meet all requirements:

Cotton Standard 20° (programme 6) ideal for heavily
soiled cotton loads. The effective performance levels
achieved at cold temperatures, which are comparable to
washing at 40°, are guaranteed by a mechanical action
which operates at varying speed, with repeated and
frequent peaks.
Mix Light (programme 7) ideal for mixed loads (cotton
and synthetics) with a normal soil level. The effective
performance levels achieved at cold temperatures are
guaranteed by a mechanical action which operates at
varying speed, across set average intervals.
20’ Refresh (programme 8) ideal for refreshing and
washing lightly soiled garments in a few minutes. It lasts
just 20 minutes and therefore saves both time and energy.
It can be used to wash different types of fabrics together
(except for wool and silk), with a maximum load of 1.5 kg.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.

1

2

3

11

GB

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be solved easily using the following list.

Problem:

The washing machine does not
switch on.

The wash cycle does not start.

The washing machine does not
take in water (“H2O” will flash on
the display).

The washing machine continuously
takes in and
drains water.

The washing machine does not
drain or spin.

The washing machine vibrates a lot
during the spin cycle.

The washing machine leaks.

The “option” indicator lights and the
“start/pause” indicator light flash and
an error code appears on the display
(e.g.: F-01, F-..).

There is too much foam.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

• The washing machine door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set..

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.

• The wash cycle does not include draining: some wash cycles require the drain
phase to be started manually.

• The “Easy iron” option has been activated: To complete the wash cycle, press
the START/PAUSE button (see “Wash cycles and options”).

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washing machine is not level (see “Installation”).

• The washing machine is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text
“for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

12

GB

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

• Restart the programme to check whether the problem has been solved;

• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the
guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.

HR

13

Hrvatski

Pregled

Postavljanje, 14-15

Raspakiranje i izravnavanje
Hidraulični i električni priključci
Prvi ciklus pranja
Tehnički podaci

Održavanje i očuvanje, 16

Zatvaranje vode i isključivanje električne struje
Čišćenje perilice
Čišćenje pretinca za deterdžent
Očuvanje vrata i bubnja
Čišćenje crpke
Provjera cijevi za dovod vode

Mjere predostrožnosti i savjeti, 17

Opća sigurnost
Rashodovanje
Ručno otvaranje vrata

Opis perilice rublja, 18-19

Kontrolna ploča
Display

Kako obaviti ciklus pranja, 20

Programi i funkcije, 21

Tablica programa
Funkcije pranja

Deterdžent i rublje, 22

Pretinac za deterdžent
Pripremanje rublja
Naročiti programi
Sustav uravnoteženja napunjenosti

Nepravilnosti i rješenja, 23

Servisna služba, 24

HR

IWSE 61051

Upute za uporabu

PERILICA RUBLJA

14

HR

! Važno je sačuvati ove upute kako bi ste ih
mogli proučiti u svakom trenutku. U slučaju
prodaje, ustupanja ili seljenja, provjeriti da se
nalaze zajedno s perilicom kako bi se novog
vlasnika obavijestilo o funkcioniranju stroja i
o upozorenjima koja se na njega odnose.

! Pozorno pročitajte ove upute: one sadrže
važne obavijesti o postavljanju, uporabi i
sigurnosti.

Raspakiranje i izravnavanje

Raspakiranje

1. Raspakujte perilicu.

2. Provjerite da perilica nije oštećena u prije-

vozu. Ako je oštećena, nemojte je priključivati
i obratite se preprodavaču.

3. Skinite 4 vijka za
zaštitu u prijevozu i
gumicu s odstojni­kom na stražnjoj stra­ni (vidi sliku).

4. Zatvorite otvore dostavljenim plastičnim

čepovima.

5. Sačuvajte sve dijelove: ako je potrebno

prevoziti perilicu, treba ih ponovno namjestiti.

! Pakovanje nije igračka za djecu!

Izravnavanje

1. Postavite perilicu na čvrst i ravan pod i ne

naslanjajte je na zidove, namještaj ili drugo.

2. Ako pod nije po­tpuno vodoravan,
nadoknadite razliku
u visini odvijanjem ili
navijanjem prednjih
nožica (vidi sliku); kut
nagiba izmjeren na
gornjoj površini ne
smije prelaziti 2°.

Pomno izravnavanje daje stroju stabilnost i
spriječava vibracije, buku i pomicanja tijekom
rada. U slučaju da perilicu postavljate na
tepison ili sag, podesite nožice tako da ispod
perilice ostane dovoljno prostora za protje­canje zraka.

Hidraulični i električni priključci

Spajanje cijevi za dovod vode

1. Spojite dovodnu
cijev navijajući je na
slavinu s hladnom vo­dom nareznog otvora
3/4, kao za plinski
priključak (vidi sliku).
Prije spajanja pustite
vodu da teče dok ne
bude bistra.

2. Spojite dovod­nu cijev na perili­cu navijanjem na
odgovarajući otvor
za uzimanje vode na
stražžnjoj strani gore
desno (vidi sliku).

3. Pazite da na cijevi nema pregiba ni
suženja.

! Pritisak vode u slavini mora se nalazi­ti među vrijednostima navedenim u tablici
Tehnički podaci (vidi slijedeću stranicu).

! Ako dužina dovodne cijevi nije dostatna,
obratite se specijaliziranoj prodavaonici ili
ovlaštenom tehničaru.

! Nemojte upotrebljavati već korištene cijevi.

! Upotrijebite one dostavljene sa strojem.

Postavljanje

HR

15

65 - 100 cm

Spajanje cijevi za odvod vode

Bez savijanja spoji­te odvodnu cijev na
odvodni cjevovod
ili odljev u zidu, koji
moraju biti u visini
od 65 do 100 cm od
poda;

odnosno naslonite je
na rub umivaonica ili
kade i vežite dosta­vljenu vodilicu na
slavinu (vidi sliku).
Slobodni završetak
odvodne cijevi ne
smije ostati uronjen
u vodu.

! Ne preporučuje se uporaba produžne cijevi,
no ako je neophodna, mora imati isti promjer
kao i originalna cijev i ne smije biti duža od
150 cm.

Električni priključak

Prije umetanja utikača u utičnicu, provjerite da:

• utičnica ima uzemljenje i da je u skladu sa
zakonskim propisima;

• utičnica može podnijeti najveću snagu
stroja naznačenu u tablici Tehnički podaci

(vidi sa strane);

• se napon struje nalazi među vrijednostima
navedenim u tablici Tehnički podaci (vidi sa

strane);

• utičnica odgovara utikaču perilice. U protiv­nom, zamijenite utičnicu ili utikač.

! Perilicu se ne smije instalirati na otvorenom
pa ni ako se radi o zaštićenom prostoru, jer
je vrlo opasno izložiti je kiši i nevremenu.

! Utičnica mora biti lako dohvatljiva i nakon
postavljanja perilice.

Tehnièki podaci

Model IWSE 61051

Dimenzije

širina 59,5 cm
visina 85 cm
dubina 42 cm

Kapacitet od 1 do 6 kg

Elektrièno
prikljuèi­vanje

vidi ploèicu s tehnièkim
osobinama na stroju

Hidraulièno
prikljuèi­vanje

maksimalan pritisak:
1 MPa (10 bar)
minimalan pritisak:
0,05 MPa (0,5 bar)
kapacitet bubnja: 40 l

Brzina
centrifugi­ranja

do 1000 okretaja u minuti

Programi
kontrole
po propisu

1061/2010 a
1015/2010

program 2; Standardni
Pamuk 60°C.
program 3; Standardni
Pamuk 40°C.

Ovaj je ureðaj u skladu sa
slijedeæim Uredbama EU:

- 2004/108/CE (Elektro­magnetska kompatibilnost)

- 2002/96/CE

- 2006/95/CE (Nizak
pritisak)

! Zabranjeno je korištenje produžnih kabela i
višestrukih utičnica.

! Ne smije se pregibati ili pritiskati kabel.

! Električni kabel smiju promijeniti jedino

ovlašteni tehničari.

Pozor! Proizvođač otklanja bilo kakvu odgo­vornost u slučaju nepoštivanja ovih propisa.

Prvi ciklus pranja

Nakon postavljanja a prije uporabe, izvršite
ciklus pranja s deterdžentom ali bez rublja,
postavljajući program 2.

16

HR

Da bi ste došli do pred-prostora:

1. pomoću odvijača
skinite ploču na
prednjem dijelu peri­lice (vidi sliku);

2. odvijte poklopac
okrećući ga obratno
od smjera kazaljke
na satu (vidi sliku) ­normalno je da izađe
malo vode;

3. brižljivo očistite unutrašnjost;

4. ponovno zavijte poklopac;

5. provjerite da su kukice ulegle u
odgovarajuća ležišta prije no što uglavite
ploču na mjesto.

Provjera cijevi za dovod vode

Provjerite cijev za dovod vode barem jednom
godišnje. Ako postoje napukline ili pukotine
potrebno ju je promijeniti: visoki pritisci bi
tijekom pranja mogli prouzročiti iznenadno
pucanje.

! Nemojte upotrebljavati već korištene cijevi.

Održavanje i očuvanje

Zatvaranje vode i isključivanje
električne struje

• Nakon svakog pranja zatvorite slavinu
s vodom. Tako se ograničava trošenje
hidrauličnih instalacija perilice i uklanja
opasnost gubitka.

• Isključite utikač iz struje dok čistite perilicu,
kao i prilikom izvođenja radova održavanja.

Čišćenje perilice

Vanjski dio i gumene dijelove može se čistiti
krpom namočenom u mlakoj vodi i sapunu.
Ne upotrebljavajte rastvorna sredstva ili ona
koja bi mogla ogrepsti površinu.

Čišćenje pretinca za deterdžent

Izvucite preti­nac podižući ga i
povlačeći prema vani
(vidi sliku).
Operite ga u tekućoj
vodi; ovo čišćenje
treba često vršiti.

Očuvanje vrata i bubnja

• Ostavljajte uvijek pritvorena vrata kako bi
se izbjeglo stvaranje neugodnih mirisa.

Čišćenje crpke

Perilica posjeduje samočišćeću crpku koju
nije potrebno održavati. Može se, međutim,
dogoditi da sitni predmeti (sitan novac, du­gma) padnu u pred-prostor koji zaštićuje
crpku, a nalazi se u njenom donjem dijelu.

! Provjerite da je ciklus pranja završio i
iskopčajte prekidač.

HR

17

Radi podrobnijih obavijesti o pravilnom rashodovanju

električnih kućanskih aparata, posjednici se mogu
obratiti nadležnoj javnoj službi ili preprodavačima.

Ručno otvaranje vrata

Ako želite prostrti rublje a zbog nestanka električne
energije nije moguće otvoriti vrata, postupite na slijedeći
način:

1. izvucite utikač iz utičnice;

2. provjerite da je razina
vode u unutrašnjosti stroja
niža od otvora vrata; u su­protnom, pomoću odvodne
cijevi ispraznite višak vode
u kantu, kako je prikazano
na slici;

3. pomoću odvijača skinite
ploču na prednjem dijelu
perilice (vidi sliku);

4. povucite prema vani jezičak prikazan na slici, sve dok
ne otkočite plastični remen, kojeg zatim treba povući
prema dole otvarajući istovremeno vrata;

5. provjerite da su kukice ulegle u odgovarajuća ležišta
prije no što uglavite ploču na mjesto.

Mjere predostrožnosti i
savjeti

! Perilica je osmišljena i ostvarena u skladu s

međunarodnim propisima o sigurnosti. Ova se upozoren­ja daju u svrhu zaštite i mora ih se pozorno pročitati.

Opća sigurnost

• Ovaj aparat je osmišljen za uporabu isključivo u
domaćinstvu.

• Ovaj uređaj smiju koristiti djeca od 8 godi­na nadalje i osobe sa smanjenim zičkim,
osjetilnim ili umnim sposobnostima, od­nosno s nedovoljno iskustva i znanja ako
ih se nadzire ili su primjereno upućeni u
sigurnu uporabu uređaja i razumiju pove­zane opasnosti. Djeca se ne smiju igrati s
uređajem. Djeca ne smiju vršiti održavanje i
čišćenje bez nadzora.

• Perilicu smiju koristiti jedino odrasle osobe i to po upu­tama iz ovog priručnika.

• Ne dodirujte stroj bosih nogu ni s vlažnim rukama ili
stopalima.

• Ne isključujte utikač iz utičnice potezanjem kabela, već
hvatajući utikač.

• Ne otvarajte pretinac za deterdžent dok stroj radi.

• Ne dirajte izbačenu vodu jer može dostići visoke tem­perature.

• Ni u kom slučaju nemojte nasilno rukovati vratima: mo­gao bi se oštetiti sigurnosni mehanizam koji spriječava
slučajno otvaranje.

• U slučaju kvara nemojte dirati ni pokušavati popravljati
unutarnje mehanizme.

• Provjeravajte uvijek da se djeca ne približavaju stroju
dok radi.

• Vrata se tijekom pranja obično zagrijavaju.

• Ako je potrebno premjestiti perilicu, neka to obave
dvije ili tri osobe uz najveću moguću pozornost. Ne
pokušavajte je sami premjestiti jer je vrlo teška.

• Prije unošenja rublja provjerite da li je bubanj prazan.

Rashodovanje

• Rashodovanje materijala od ambalaže: pridržavati se
lokalnih propisa, tako će se pakovanje moći ponovno
upotrijebiti.

• Europska direktiva 2002/96/EZ o električnom i
elektronskom otpadu propisuje da se električne
kućanske aparate ne smije zbrinjavati zajedno s
običnim krutim komunalnim otpadom. Rashodovane
aparate treba sakupljati posebno, radi optimiziranja
stope spašavanja i recikliranja materijala od kojih su
izrađeni te radi spriječavanja moguće štete po zdra­vlje i po okoliš. Simbol prekrižene kante za smeće koji
se nalazi na svim proizvodima podsjeća na obavezu
odvojenog sakupljanja otpada.

18

HR

Pretinac za deterdžent: služi za stavljanje deterđenta i
aditiva (vidi “Deterđenti i rublje”).

Tipka ON/OFF : nakratko pritisnite ovu tipku da bi
uključili ili isključili stroj. Sporo treptanje kontrolnog
svjetla START/PAUSE u zelenoj boji označava da je stroj
uključen. Za isključivanje perilice rublja tijekom pranja ti­pku treba držati pritisnutu duže - oko 3 s; kratki ili slučajni
pritisak neće izazvati isključivanje stroja. Ako se stroj
tijekom pranja isključi, program pranja će se poništiti.

Gumb PROGRAM: služi za postavljanje programa. Ti­jekom odvijanja programa gumb ostaje nepomičan.

Tipke s kontrolnim svjetlima FUNKCIJA: njima odabire­mo raspoložive funkcije. Kontrolno svjetlo koje se odnosi
na dotičnu funkciju ostat će upaljeno.

Tipka CENTRIFUGA : pritisnite da bi smanjili ili potpu-
no isključili centrifugiranje – vrijednost će biti prikazana
na displayu.

Tipka TEMPERATURA : pritisnite da bi snizili tempera-
turu - vrijednost će biti prikazana na displayu.

Tipka ODGOĐENO POKRETANJE : pritisnite da bi
postavili odgođeno pokretanje izabranog programa.
Kašnjenje će biti prikazano na displayu.

Tipka s kontrolnim svjetlom START/PAUSE : dok zeleno
kontrolno svjetlo sporo trepti, pritisnite ovu tipku da bi
pokrenuli pranje. Kad se ciklus pokrene, kontrolno svjetlo
ostaje stalno upaljeno. Da bi postavili stanku u pranju
ponovno pritisnite ovu tipku: kontrolno svjetlo će treptati
narančastom bojom. Ako simbol ne svjetli, možete ot­voriti vrata. Da se pranje nastavi odvijati od točke u kojoj
je prekinuto, ponovno pritisnite ovu tipku.

Način Stand-by

Ova perilica rublja, sukladno novim normativama u
svezi štednje elektricne energije, posjeduje sustav
automatskog gašenja (“Stand By”), koji se - u slucaju
nekorištenja stroja - aktivira nakon 30 minuta. Kratko
pritisnite tipku ON/OFF i cekajte da se stroj ponovno
aktivira.

Potrošnja u načinu isključeno: 0,5 W
Potrošnja u načinu ostavljeno da odstoji: 0,5 W

Opis perilice rublja

Tipka s kontrolnim
svjetlom START/

PAUSE

Kontrolna ploča

Tipka

TEMPERATURA

Tipka

CENTRIFUGA

Tipka ON/OFF

Pretinac za deterdžent

DISPLAY

Tipka

ODGOĐENO
POKRETANJE

Gumb

PROGRAM

Tipke s kontrolnim
svjetlima

FUNKCIJA