Indesit IWD 81283 Eco operation manual

Instructions for use

WASHING MACHINE

GB

English,1

IWD 81283

F

Français,13

DE

Deutsch,15

Contents

Installation, 2-3

Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data

Care and maintenance, 4

Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose

Precautions and tips, 5

General safety
Disposal

Description of the washing machine
and starting a wash cycle, 6-7

Control panel
Indicator lights
Starting a wash cycle

GB

Wash cycles, 8

Table of wash cycles

Personalisation, 9

Setting the temperature
Setting the spin speed
Functions

Detergents and laundry, 10

Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Load balancing system

Troubleshooting, 11

Service, 12

1

Installation

GB

! This instruction manual should be kept in a safe

place for future reference. If the washing machi­ne is sold, transferred or moved, make sure that
the instruction manual remains with the machine
so that the new owner is able to familiarise him­self/herself with its operation and features.
! Read these instructions carefully: they con­tain vital information relating to the safe instal­lation and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its
packaging.

2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.

3. Remove the 4 pro­tective screws (used
during transportation)
and the rubber wa­sher with the cor­responding spacer,
located on the rear
part of the appliance
(see figure).

4. Close off the holes using the plastic plugs
provided.

5. Keep all the parts in a safe place: you will
need them again if the washing machine ne­eds to be moved to another location.

Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.

Connecting the electricity and
water supplies

Connecting the water inlet hose

1. Connect the sup­ply pipe by screwing
it to a cold water tab
using a ¾ gas threa­ded connection (see

figure).

Before performing the
connection, allow the
water to run freely un­til it is perfectly clear.

2. Connect the inlet
hose to the washing
machine by screwing
it onto the correspon­ding water inlet of the
appliance, which is
situated on the top
right-hand side of the
rear part of the ap­pliance (see figure).

! Packaging materials should not be used as
toys for children.

Levelling

1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furni­ture cabinets or anything else.

2. If the floor is not
perfectly level, com­pensate for any une­venness by tightening
or loosening the
adjustable front feet
(see figure); the angle
of inclination, measu­red in relation to the
worktop, must not
exceed 2°.

2

3. Make sure that the hose is not folded over
or bent.

! The water pressure at the tap must fall within
the values indicated in the Technical details
table (see next page).

! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

data plate fixed to the machine

65 - 100 cm

Connecting the drain hose

Connect the drain
hose, without bending
it, to a drainage duct
or a wall drain located
at a height between
65 and 100 cm from
the floor;

alternatively, rest it on
the side of a washba­sin or bathtub, faste­ning the duct sup­plied to the tap (see
figure). The free end
of the hose should
not be underwater.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be repla-

ced by authorised technicians.

Warning! The company shall not be held
responsible in the event that these regulations
are not respected.

The first wash cycle

Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle 2.

Technical data

GB

! We advise against the use of hose exten­sions; if it is absolutely necessary, the exten­sion must have the same diameter as the
original hose and must not exceed 150 cm in
length.

Electrical connections

Before plugging the appliance into the electri­city socket, make sure that:

• the socket is earthed and complies with all
applicable laws;

• the socket is able to withstand the maximum
power load of the appliance as indicated in
the Technical data table (see opposite);

• the power supply voltage falls within the
values indicated in the Technical data table

(see opposite);

• the socket is compatible with the plug of
the washing machine. If this is not the case,
replace the socket or the plug.

! The washing machine must not be installed
outdoors, even in covered areas. It is extreme­ly dangerous to leave the appliance exposed
to rain, storms and other weather conditions.

! When the washing machine has been instal­led, the electricity socket must be within easy
reach.

Model

Dimensions

Capacity

Electrical
connections

Water
connection

Spin speed

Test wash
cycles in
accordan­ce with
directives
1061/2010
and
1015/2010

IWD 81283

width 59.5 cm
height 85 cm
depth 60 cm

from 1 to 8 kg

please refer to the technical

maximum pressure
1 MPa (10 bar)
minimum pressure

0.05 MPa (0.5 bar)
drum capacity 62 litres

up to 1200 rotations per
minute

Programme 3:
Cotton standard 60°C.
Programme 4:
Cotton standard 40°C.

This appliance conforms to
the following EC Directives:

- 2004/108/EC (Electroma­gnetic Compatibility) and
subsequent modifications

- 2012/19/EU

- 2006/95/EC Low Voltage)

3

Care and maintenance

GB

Cutting off the water and electri­city supplies

• Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system
inside the washing machine and help to pre­vent leaks.

• Unplug the washing machine when cleaning
it and during all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.

Cleaning the detergent dispenser
drawer

Remove the dispenser
by raising it and pul­ling it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.

2. unscrew the lid
by rotating it anti­clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.

! Never use second-hand hoses.

Caring for the door and drum of
your appliance

• Always leave the porthole door ajar in order
to prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cle­aning pump which does not require any main­tenance. Sometimes, small items (such as
coins or buttons) may fall into the pre-chamber
which protects the pump, situated in its bot­tom part.

! Make sure the wash cycle has finished and
unplug the appliance.

To access the pre­chamber:

1. using a screwdri­ver, remove the cover
panel on the lower
front part of the wa­shing machine (see
figure);

4

Precautions and tips

! This washing machine was designed and constructed in

accordance with international safety regulations. The fol­lowing information is provided for safety reasons and must
therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children aged

from 8 years and above and persons with re­duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Chil­dren shall not play with the appliance. Clea­ning and user maintenance shall not be made
by children without supervision.

• Do not touch the machine when barefoot or with wet or
damp hands or feet.

• Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.

• Do not open the detergent dispenser drawer while the
machine is in operation.

• Do not touch the drained water as it may reach extreme­ly high temperatures.

• Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.

• If the appliance breaks down, do not under any circum­stances access the internal mechanisms in an attempt
to repair it yourself.

• Always keep children well away from the appliance while
it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make
sure the drum is empty.

Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.

GB

Disposal

• Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU on Waste

Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on human
health and the environment. The crossed out “wheeled
bin” symbol on the product reminds you of your obliga­ tion, that when you dispose of the appliance it must be
separately collected.

5

Description of the washing
machine and starting a wash cycle

GB

Control panel

Detergent dispenser drawer

ON/OFF

WASH CYCLE

button

knob

DELAY TIMER

button

DISPLAY

TEMPERATURE

knob

FUNCTION

buttons with
indicator lights

SPIN SPEED

knob

WASH CYCLE
PROGRESS

START/
PAUSE

button with
indicator light

DOOR LOCKED

indicator light

Detergent dispenser drawer: used to dispense deter­gents and washing additives (see “Detergents and laundry”).

ON/OFF button: switches the washing machine on and off.

WASH CYCLE knob: programmes the wash cycles. Du-

ring the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.

TEMPERATURE knob: sets the temperature or the cold
wash cycle (see “Personalisation”).

SPIN SPEED knob: sets the spin speed or exclude the
spin cycle completely (see “Personalisation”).

DISPLAY: used to view the duration of the various cycles
available and the remaining time of a cycle in progress;
if the DELAY TIMER option has been selected, the
countdown to the start of the selected cycle will appear.

DELAY TMER button : press to set a delayed start
time for the selected wash cycle. The delay time will be
shown on the display.

WASH CYCLE PROGRESS

monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in
progress.

DOOR LOCKED indicator light: indicates whether the
door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or tem­porarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash orange,
while the indicator light for the current wash cycle phase
will remain lit in a fixed manner. If the DOOR LOCKED
indicator light is switched off, the door may be opened.
To start the wash cycle from the point at which it was
interrupted, press this button again.

Standby mode

This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby sy­stem which is enabled after about 30 minutes if no activity
is detected. Press the ON-OFF button briefly and wait for
the machine to start up again.

Consumption in off-mode: 0,5 W
Consumption in Left-on: 8 W

indicator light

s: used to

6

Indicator lights

The indicator lights provide important information.
This is what they can tell you:

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has
begun, the indicator lights switch on one by one to indicate
which phase of the cycle is currently in progress.

Wash

Rinse

Spin

Drain

End of wash cycle

Function buttons and corresponding indicator
lights

When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the program­med wash cycle, the corresponding indicator light will flash
and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the indicator
light corresponding to the first function selected will
flash and only the second function will be activated; the

indicator light corresponding to the enabled option will
remain lit.

Door locked indicator light

When the indicator light is on, the porthole door is locked
to prevent it from being opened; make sure the indicator
light is off before opening the door (wait approximately 3
minutes). To open the door during a running wash cycle,
press the START/PAUSE button; the door may be opened
once the DOOR LOCKED indicator light turns off.

GB

Starting a wash cycle

1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then
they will switch off and the START/PAUSE indicator light will pulse.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see “Personalisation”).

5. Set the spin speed (see “Personalisation”).

6. Measure out the detergent and washing additives (see “Detergents and laundry”).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed

manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9. At the end of the wash cycle the END indicator light will switch on. The door can be opened once the DOOR LOCK
indicator light turns off. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely.
Switch the washing machine off by pressing the ON/OFF button.

7

Wash cycles

GB

Table of wash cycles

Description of the wash cycle

Wash cycles

Daily

1

Cotton with prewash: extremely soiled whites. 90° 1200

2

Cotton: extremely soiled whites. 90° 1200 -

3

Cotton Standard 60° (1): heavily soiled whites and resistant colours. 60° 1200 -

4

Cotton Standard 40° (2): lightly soiled whites and delicate colours. 40° 1200 -

5

Coloured Cottons: lightly soiled whites and delicate colours. 40° 1200 -

6

Synthetics: heavily soiled resistant colours. 60° 800 -

6

Synthetics (3): lightly soiled resistant colours. 40° 800 -

7

Cotton Standard 20°: lightly soiled whites and delicate colours. 20° 1200 -
Special

8

Wool: for wool, cashmere, etc. 40° 800 -

9

Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0 -
10 Jeans
11 Outwear

Sport
12 Sport Intensive
13 Sport Light

14 Special Shoes

Partial wash cycles

Rinse - 1200 - -

Spin + Drain - 1200 - - - 8 - - - 16‘

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water
temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 3 with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for
garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 4 with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for
garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.

3) Long wash cycle for synthetics: set wash cycle 6; with a temperature of 40°C.

Max.

temp.

Max.

speed

(°C)

(rpm)

40° 800 -

30° 400 -

30° 600 ­30° 600 -

30° 600 -

Detergents

Wash

Prewash

  

 
 
 
 
 
 
 

 
 
 



 
 

 

Fabric

softener

- 2,5 - - - 60’

2 pairs



Residual

dampness %

Max. load (kg)

8 53 2,72 95 190’
8 53 2,45 83 175’
8 53 1,04 55 215’
8 53 0,87 81 185’

8 53 0,79 61 95’
4,5 46 1,03 60 115’
4,5 46 0,56 60 100’

8 - - - 175’

2 - - - 90’

2 - - - 65’

4 - - - 80’

4 - - - 85’

4 - - - 60’

Max.

- - - 60’

8 - - - 36‘

Total water lt

consumption

kWh

Energy

Cycle

duration

Cotton Standard 20° (wash cycle 7) ideal for lightly soiled cotton loads. The effective performance levels achieved at cold

temperatures, which are comparable to washing at 40°, are guaranteed by a mechanical action which operates at varying
speed, with repeated and frequent peaks.
Outwear (

wash cycle

11) is studied for washing water-repellent fabrics and winter jackets (e.g. Gore-Tex, polyester, nylon);

for best results, use a liquid detergent and dosage suitable for a half-load; pre-treat necks, cuffs and stains if necessary;
do not use softeners or detergents containing softeners. Stuffed duvets cannot be washed with this programme.
Sport Intensive (

wash cycle

12) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.); for best

results, we recommend not exceeding the maximum load indicated in the “Table of wash cycles”.
Sport Light (

wash cycle

13) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results,

we recommend not exceeding the maximum load indicated in the “Table of wash cycles”. We recommend using a
liquid detergent and dosage suitable for a half-load.
Special Shoes (

wash cycle

14) is for washing sports shoes; for best results, do not wash more than 2 pairs simultaneously.

8

Personalisation

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash .
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value
set for each wash cycle.

Setting the spin speed

Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:

Wash cycles Maximum spin speed

Cottons 1200 rpm
Synthetics 800 rpm
Wool 800 rpm
Silk drain only

The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.

Functions

The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the
selected wash cycle.

GB

Delay timer

To set a delayed start for the selected programme, press the corresponding button repeatedly until the required delay period
has been reached. When this option is enabled, the symbol lights up on the display. To remove the delayed start option
press the button until the text “OFF” appears on the display.

! This option is enabled with all programmes.

Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled
cotton and synthetic fabrics (refer to the “
water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.

“Table of wash cycles”

). “ ” enables you to wash in less time thereby saving

! This function may not be used in conjunction with wash cycles 1, 2, 7, 8, 9, 10, 11, 12, 13, 14, , .

The function saves energy by not heating the water used to wash your laundry - an advantage both to the
environment and to your energy bill. Instead, intensified wash action and water optimisation ensure great wash results in the
same average time of a standard cycle.
For the best washing results we recommend the usage of a liquid detergent.

! This function may not be used in conjunction with wash cycles 1, 7, 8, 9, 12, 13, 14, , .

9

Detergents and laundry

1

2

3

GB

Detergent dispenser drawer

Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessa­rily result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.

! Do not use hand washing detergents because these

create too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent di­spenser drawer and pour
in the detergent or washing
additive, as follows.

Silk: use special wash cycle 9 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 9.
Jeans: Turn garments inside-out before washing and use
a liquid detergent. Use programme 10.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.

compartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)

Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the values listed in the “Table of wash
cycles”, which refer to the weight of the laundry when
dry.

How much does your laundry weigh?

1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g

Garments requiring special care

Wool: all wool garments can be washed using programme

8, even those carrying the “hand-wash only” label. For
best results, use special detergents and do not exceed
2 kg of laundry.

10

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be solved easily using the following list.

Problem:

The washing machine does not
switch on.

The wash cycle does not start.

The washing machine does not
take in water (“H2O” will flash on
the display).

The washing machine continuously
takes in and drains water.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

• The washing machine door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set (see “Personalisation”).

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.

GB

The washing machine does not
drain or spin.

The washing machine vibrates a lot
during the spin cycle.

The washing machine leaks.

The “function” indicator lights and
the “start/pause” indicator light flash,
while one of the “phase in progress”
indicator lights and the “door locked”
indicator light will remain lit in a fixed
manner.

There is too much foam.

• The wash cycle does not include draining: some wash cycles require the drain
phase to be started manually.

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washing machine is not level (see “Installation”).

• The washing machine is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see
“Care and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and
then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text
“for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

11