INDESIT IWD 71052SL C ECO EU User Manual

Instructions for use
WASHING MACHINE
GB
English, 1
TR
Türkçe,37
IWD 71052
FR
Français,13
ES
Español,25
Contents
Installation, 2-3
Unpacking and levelling Connecting the electricity and water supplies The first wash cycle Technical data
Cutting off the water or electricity supply Cleaning the washing machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose
Precautions and tips, 5
General safety Disposal
Description of the washing machine and starting a wash cycle, 6-7
Control panel Indicator lights Starting a wash cycle
GB
Wash cycles, 8
Table of wash cycles
Personalisation, 9
Setting the temperature Setting the spin speed Functions
Detergents and laundry, 10
Detergent dispenser drawer Preparing the laundry Garments requiring special care Load balancing system
Troubleshooting, 11
Service, 12
1
Installation
GB
! This instruction manual should be kept in a safe
place for future reference. If the washing machine is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/ herself with its operation and features. ! Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been damaged during the transportation process. If it has been damaged, contact the retailer and do not proceed any further with the installation process.
3. Remove the 4 pro­tective screws (used during transportation) and the rubber washer with the corresponding spacer, located on the rear part of the applian­ce (see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need them again if the washing machine needs to be moved to another location.
! Packaging materials should not be used as toys for children.
Levelling
1. Install the washing machine on a flat sturdy floor, without resting it up against walls, furnitu­re cabinets or anything else.
2. If the floor is not perfectly level, com­pensate for any une­venness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measu­red in relation to the worktop, must not exceed 2°.
Levelling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise and prevent it from shifting while it is operating. If it is placed on carpet or a rug, adjust the feet in such a way as to allow a sufficient ventilation space underneath the washing machine.
Connecting the electricity and water supplies
Connecting the water inlet hose
1. Connect the supply pipe by screwing it to a cold water tap using a ¾ gas threaded con­nection (see figure). Before performing the connection, allow the water to run freely until it is perfectly clear.
2. Connect the inlet hose to the washing machine by screwing it onto the correspon­ding water inlet of the appliance, which is si­tuated on the top right­hand side of the rear part of the appliance (see figure).
3. Make sure that the hose is not folded over or bent.
! The water pressure at the tap must fall within the values indicated in the Technical details table (see next page).
! If the inlet hose is not long enough, contact a specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
2
65 - 100 cm
Connecting the drain hose
Connect the drain hose, without bending it, to a drainage duct or a wall drain located at a height between 65 and 100 cm from the floor;
alternatively, rest it on the side of a washba­sin or bathtub, faste­ning the duct sup­plied to the tap (see figure). The free end of the hose should not be underwater.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be repla-
ced by authorised technicians.
Warning! The company shall not be held responsible in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, using the wash cycle 2.
Technical data
GB
! We advise against the use of hose exten­sions; if it is absolutely necessary, the exten­sion must have the same diameter as the original hose and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electri­city socket, make sure that:
• the socket is earthed and complies with all applicable laws;
• the socket is able to withstand the maximum power load of the appliance as indicated in the Technical data table (see opposite);
• the power supply voltage falls within the values indicated in the Technical data table
(see opposite);
• the socket is compatible with the plug of the washing machine. If this is not the case, replace the socket or the plug.
! The washing machine must not be installed outdoors, even in covered areas. It is extreme­ly dangerous to leave the appliance exposed to rain, storms and other weather conditions.
! When the washing machine has been instal­led, the electricity socket must be within easy reach.
Model
Dimensions
Capacity
Electrical connections
Water con­nection
Spin speed
Test wash cycles in accordan­ce with directives 1061/2010 and 1015/2010
IWD 71052
width 59.5 cm height 85 cm depth 53,5 cm
from 1 to 7 kg please refer to the technical
data plate fixed to the ma­chine
maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.5 bar) drum capacity 52 litres
up to 1000 rotations per minute
Programme 2: Cotton stan­dard 60°C; Programme 3: Cotton stan­dard 40°C.
This appliance conforms to the following EC Directives:
- 2004/108/EC (Electroma­gnetic Compatibility)
- 2012/19/EU
- 2006/95/EC Low Voltage)
3
Care and maintenance
GB
Cutting off the water and electri­city supplies
• Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washing machine and help to pre­vent leaks.
• Unplug the washing machine when cleaning it and during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser drawer
Remove the dispenser by raising it and pul­ling it out (see figure). Wash it under running water; this operation should be repeated frequently.
2. unscrew the lid by rotating it anti­clockwise (see figu- re): a little water may trickle out. This is perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are any cracks, it should be replaced immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.
! Never use second-hand hoses.
Caring for the door and drum of your appliance
• Always leave the porthole door ajar in order to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cle­aning pump which does not require any main­tenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber which protects the pump, situated in its bot­tom part.
! Make sure the wash cycle has finished and unplug the appliance.
To access the pre­chamber:
1. using a screwdri­ver, remove the cover panel on the lower front part of the wa­shing machine (see figure);
4
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol­lowing information is provided for safety reasons and must therefore be read carefully.
General safety
• This appliance was designed for domestic use only.
This appliance can be used by children aged
from 8 years and above and persons with re­duced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Chil­dren shall not play with the appliance. Clea­ning and user maintenance shall not be made by children without supervision.
• Do not touch the machine when barefoot or with wet or damp hands or feet.
• Do not pull on the power supply cable when unplugging the appliance from the electricity socket. Hold the plug and pull.
• Do not open the detergent dispenser drawer while the machine is in operation.
• Do not touch the drained water as it may reach extreme­ly high temperatures.
• Never force the porthole door. This could damage the safety lock mechanism designed to prevent accidental opening.
• If the appliance breaks down, do not under any circum­stances access the internal mechanisms in an attempt to repair it yourself.
• Always keep children well away from the appliance while it is operating.
• The door can become quite hot during the wash cycle.
• If the appliance has to be moved, work in a group of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy.
• Before loading laundry into the washing machine, make sure the drum is empty.
Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.
GB
Disposal
• Disposing of the packaging materials: observe local regulations so that the packaging may be re-used.
• The European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment, requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obliga­ tion, that when you dispose of the appliance it must be separately collected.
5
Description of the washing machine and starting a wash cycle
GB
Control panel
Detergent dispenser drawer
ON/OFF
WASH CYCLE
button
knob
DELAY TIMER
button
DISPLAY
TEMPERATURE
knob
FUNCTION
buttons with indicator lights
SPIN SPEED
knob
WASH CYCLE PROGRESS
START/ PAUSE
button with indicator light
DOOR LOCKED
indicator light
Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”).
ON/OFF button: switches the washing machine on and off.
WASH CYCLE knob: programmes the wash cycles. Du­ring the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the available functions. The indicator light corresponding to the selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold wash cycle (see “Personalisation”).
SPIN SPEED knob: sets the spin speed or exclude the spin cycle completely (see “Personalisation”).
DISPLAY: used to view the duration of the various cycles available and the remaining time of a cycle in progress; if the DELAY TIMER option has been selected, the countdown to the start of the selected cycle will appear.
DELAY TMER button time for the selected wash cycle. The delay time will be shown on the display.
: press to set a delayed start
WASH CYCLE PROGRESS
monitor the progress of the wash cycle. The illuminated indicator light shows which phase is in progress.
DOOR LOCKED indicator light: indicates whether the door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tem­porarily interrupts the wash cycles. N.B. To pause the wash cycle in progress, press this button; the corresponding indicator light will flash orange, while the indicator light for the current wash cycle phase will remain lit in a fixed manner. If the DOOR LOCKED indicator light is switched off, the door may be opened (wait approximately 3 minutes). To start the wash cycle from the point at which it was inter­rupted, press this button again.
Standby mode
This washing machine, in compliance with new energy sa­ving regulations, is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected. Press the ON-OFF button briefly and wait for the machine to start up again.
indicator light
s: used to
6
Indicator lights
The indicator lights provide important information. This is what they can tell you:
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has begun, the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress.
Wash
Rinse
Spin
Drain
End of wash cycle
Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator light will illuminate. If the selected function is not compatible with the program­med wash cycle, the corresponding indicator light will flash and the function will not be activated. If the selected function is not compatible with another function which has been selected previously, the indicator light corresponding to the first function selected will flash and only the second function will be activated; the
indicator light corresponding to the enabled option will remain lit.
Door locked indicator light
When the indicator light is on, the porthole door is locked to prevent it from being opened; make sure the indicator light is off before opening the door (wait approximately 3 minutes). To open the door during a running wash cycle, press the START/PAUSE button; the door may be opened once the DOOR LOCKED indicator light turns off.
GB
Starting a wash cycle
1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then they will switch off and the START/PAUSE indicator light will pulse.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed
manner, in green. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the cator light turns off (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch the washing machine off by pressing the ON/OFF button.
indicator light will switch on. The door can be opened once the DOOR LOCK indi-
7
GB
Wash cycles
Table of wash cycles
Description of the wash cycle
Wash cycles
Daily
1
Cotton with prewash: extremely soiled whites.
2
Cotton Standard 60° (1): heavily soiled whites and resistant colours.
3
Cotton Standard 40° (2): lightly soiled whites and delicate colours.
4
Synthetics: heavily soiled resistant colours.
4
Synthetics (3): lightly soiled resistant colours.
5
Mix Colored: lightly soiled whites and delicate colours.
20° Zone
6
Cotton Standard 20°: lightly soiled whites and delicate colours.
7 Mix Light
8 20’ Refresh
Special
9
Silk/Curtains: for garments in silk and viscose, lingerie.
10
Wool: for wool, cashmere, etc.
11 Jeans
Sport
12 Sport Intensive
13 Sport Light
14 Sport Shoes
Partial wash cycles
Rinse
Spin + Drain
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 2 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 3 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.
3) Synthetic program along: set wash cycle 4 with a temperature of 40°C.
Max.
temp.
(°C)
(Max. 90°)
Max.
speed
(rpm)
1000
90° 60°
1000
1000
40° 60° 40° 40°
20° 20° 20°
30° 40° 40°
30° 600 ­30° 600 -
30° 600 -
800 800
1000
1000
800 800
0 800 800
1000
-
1000
-
Detergents
Pre-
Wash
wash
-
-
-
-
-
-
-
-
-
-
-
- -
- - - 7
Fabric
softener
   
 
Max.
Residual
load (kg)
dampness %
62 2,21 78 170’
7
62 1,07 52,5 180’
7
62 1,00 75 170’
7
44 0,93 47 115’
3,5
44 0,57 46 100’
3,5
62 0,66 54 90’
7
- - - 170’
7
- - - 120’
7
- - - 20’
1,5
- - - 55’
1
- - - 70’
1,5
- - - 75’
3,5
- - - 85’
2,5
- - - 60’
2,5
Max. 2
- - - 60’
Pairs
- - - 36’
7
- - - 16’
Energy
consum-
ption kWh
Total water lt
Cycle
duration
Sport Intensive (
wash cycle
12) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results, we recommend not exceeding the maximum load indicated in the “Table of wash cycles”. Sport Light (
wash cycle
13) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results, we recommend not exceeding the maximum load indicated in the “Table of wash cycles”. We recommend using a liquid detergent and dosage suitable for a half-load. Sport Shoes (
wash cycle
14) is for washing sports shoes; for best results, do not wash more than 2 pairs simultaneously.
The 20° wash cycles (20° Zone) offer effective washing performance at low temperatures, reducing electricity usage and expenditure while benefitting the environment.The 20° wash cycles meet all requirements:
Cotton Standard 20° (programme 6) ideal for lightly soiled cotton loads. The effective performance levels achieved at cold temperatures, which are comparable to washing at 40°, are guaranteed by a mechanical action which operates at varying speed, with repeated and frequent peaks. Mix Light (programme 7) ideal for mixed loads (cotton and synthetics) with a normal soil level. The effective performance levels achieved at cold temperatures are guaranteed by a mechanical action which operates at varying speed, across set average intervals. 20’ Refresh (programme 8) ideal for refreshing and washing lightly soiled garments in a few minutes. It lasts just 20 minutes and therefore saves both time and energy. It can be used to wash different types of fabrics together (except for wool and silk), with a maximum load of 1.5 kg.
8
Personalisation
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles). The temperature may be lowered, or even set to a cold wash The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value set for each wash cycle.
.
! Exception: if the 2 programme is selected, the temperature can be increased up to a value of 90°C.
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle. The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 1000 rpm Synthetics 800 rpm Wool 800 rpm Silk drain only
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed set for each wash cycle.
.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time. To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note:
- If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and
the function will not be activated.
- If the selected function is not compatible with another function which has been selected previously, the indicator light corresponding to the first function selected will flash and only the second function will be activated; the indicator light
corresponding to the enabled option will remain lit.
GB
Delay timer
To set a delayed start for the selected programme, press the corresponding button repeatedly until the required delay period has been reached. When this option is enabled, the press the button until the text “OFF” appears on the display.
Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled cotton and synthetic fabrics (refer to the
water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.
The function saves energy by not heating the water used to wash your laundry - an advantage both to the environment and to your energy bill. Instead, intensified wash action and water optimisation ensure great wash results in the same average time of a standard cycle.
For the best washing results we recommend the usage of a liquid detergent.
“Table of wash cycles”
symbol lights up on the display. To remove the delayed start option
). “ ” enables you to wash in less time thereby saving
9
Detergents and laundry
1
2
3
GB
Detergent dispenser drawer
Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessa­rily result in a more efficient wash, and may in fact cause build up on the inside of your appliance and contribute to environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent di­spenser drawer and pour in the detergent or washing additive, as follows.
compartment 1: Compartment 1: Pre-wash deter­gent (powder) compartment 2: Detergent for the wash cycle (powder or liquid)
Liquid detergent should only be poured in immediately prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Garments requiring special care
Silk: use special wash cycle 9 to wash all silk garments. We
recommend the use of special detergent which has been designed to wash delicate clothes. Curtains: fold curtains and place them in a pillow case or mesh bag. Use wash cycle 9. Wool: all wool garments can be washed using programme 10, even those carrying the “hand-wash only” For best results, use special detergents and do not exceed 1,5 kg of laundry. Jeans: Turn garments inside-out before washing and use a liquid detergent. Use programme 11.
label.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and to distribute the load in a uniform manner, the drum rotates continuously at a speed which is slightly greater than the washing rotation speed. If, after several attempts, the load is not balanced correctly, the machine spins at a reduced spin speed. If the load is excessively unbalanced, the washing machine performs the distribution process instead of spinning. To encourage improved load distribution and balance, we recommend small and large garments are mixed in the load.
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
• Do not exceed the values listed in the “Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g 1 pillow case 150-200 g 1 tablecloth 400-500 g 1 bathrobe 900-1200 g 1 towel 150-250 g
10
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not switch on.
The wash cycle does not start.
The washing machine does not take in water (“H2O” will flash on the display).
The washing machine continuously takes in and drains water.
Possible causes / Solutions:
• The appliance is not plugged into the socket fully, or is not making contact.
• There is no power in the house.
• The washing machine door is not closed properly.
• The ON/OFF button has not been pressed.
• The START/PAUSE button has not been pressed.
• The water tap has not been opened.
• A delayed start has been set (see “Personalisation”).
• The water inlet hose is not connected to the tap.
• The hose is bent.
• The water tap has not been opened.
• There is no water supply in the house.
• The pressure is too low.
• The START/PAUSE button has not been pressed.
• The drain hose is not fitted at a height between 65 and 100 cm from the floor (see “Installation”).
• The free end of the hose is under water (see “Installation”).
• The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the appliance off and contact the Assistance Service. If the dwelling is on one of the upper floors of a building, there may be problems relating to water drainage, causing the washing machine to fill with water and drain continuously. Special anti-draining valves are available in shops and help to avoid this inconvenience.
GB
The washing machine does not drain or spin.
The washing machine vibrates a lot during the spin cycle.
The washing machine leaks.
The “function” indicator lights and the “start/pause” indicator light flash, while one of the “phase in progress” indicator lights and the “door locked” indicator light will remain lit in a fixed manner.
There is too much foam.
• The wash cycle does not include draining: some wash cycles require the drain phase to be started manually.
• The drain hose is bent (see “Installation”).
• The drainage duct is clogged.
• The drum was not unlocked correctly during installation (see “Installation”).
• The washing machine is not level (see “Installation”).
• The washing machine is trapped between cabinets and walls (see “Installation”).
• The water inlet hose is not screwed on properly (see “Installation”).
• The detergent dispenser drawer is blocked (for cleaning instructions, see “Care and maintenance”).
• The drain hose is not fixed properly (see “Installation”).
• Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• The detergent is not suitable for machine washing (it should display the text “for washing machines” or “hand and machine wash”, or the like).
• Too much detergent was used.
11
Service
GB
Before calling for Assistance:
Check whether you can solve the problem alone (see “Troubleshooting”);
• Restart the programme to check whether the problem has been solved;
• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the front of the appliance by opening the door.
12
Mode d’emploi
LAVE-LINGE
FR
Français
IWD 71052
Sommaire
Installation, 14-15
Déballage et mise à niveau Raccordements eau et électricité Premier cycle de lavage Caractéristiques techniques
Entretien et soin, 16
Coupure de l’arrivée d’eau et du courant Nettoyage du lave-linge Nettoyage du tiroir à produits lessiviels. Entretien du hublot et du tambour Nettoyage de la pompe Contrôle du tuyau d’arrivée de l’eau
Précautions et conseils, 17
Sécurité générale Mise au rebut
Description du lave-linge et démarrage d’un programme, 18-19
Bandeau de commandes Voyants Démarrage d’un programme
FR
Programmes, 20
Tableau des programmes
Personnalisations, 21
Sélection de la température Sélection de l’essorage Fonctions
Produits lessiviels et linge, 22
Tiroir à produits lessiviels Triage du linge Linge ou vêtements particuliers Système d’équilibrage de la charge
Anomalies et remèdes, 23
Assistance, 24
13
Installation
FR
! Conserver ce mode d’emploi pour pouvoir le consulter à tout moment. En cas de vente, de cession ou de déménagement, veiller à ce qu’il suive toujours le lave-linge pour que son nou­veau propriétaire soit informé sur son mode de fonctionnement et puisse profiter des conseils correspondants. ! Lire attentivement les instructions: elles fournis­sent des conseils importants sur l’installation, l’utilisation et la sécurité de l’appareil.
Déballage et mise à niveau
Déballage
1. Déballer le lave-linge.
2. Contrôler que le lave-linge n’a pas été endom-
magé pendant le transport. S’il est abîmé, ne pas le raccorder et contacter le vendeur.
3. Enlever les 4 vis de protection servant au transport, le ca­outchouc et la cale, placés dans la partie arrière (voir figure).
Une bonne mise à niveau garantit la stabilité de l’appareil et évite qu’il y ait des vibrations, du bruit et des déplacements en cours de fonctionnement. Si la machine est posée sur de la moquette ou un tapis, régler les pieds de manière à ce qu’il y ait suffisamment d’espace pour assurer une bonne ventilation.
Raccordements eau et électricité
Raccordement du tuyau d’arrivée de l’eau
1. Reliez le tuyau d’ali­mentation en le vissant à un robinet d’eau froi­de à embout fileté 3/4 gaz (voir figure). Faire couler l’eau ju­squ’à ce qu’elle soit limpide et sans impure­tés avant de raccorder.
2. Raccorder le tuyau d’arrivée de l’eau au lave-linge en le vissant à la prise d’eau prévue, dans la partie arrière en haut à droite (voir figure).
4. Boucher les trous à l’aide des bouchons
plastique fournis.
5. Conserver toutes ces pièces: il faudra les
remonter en cas de transport du lave-linge.
! Les pièces d’emballage ne sont pas des jouets pour enfants.
Mise à niveau
1. Installer le lave-linge sur un sol plat et rigide,
sans l’appuyer contre des murs, des meubles ou autre.
2. Si le sol n’est pas parfaitement horizon­tal, visser ou dévisser les pieds de réglage avant (voir figure) pour niveler l’appareil; son angle d’inclinaison, mesuré sur le plan de travail, ne doit pas dépasser 2°.
3. Attention à ce que le tuyau ne soit pas plié ou écrasé.
! La pression de l’eau doit être comprise entre les valeurs indiquées dans le tableau des Ca­ractéristiques techniques (voir page ci-contre).
! Si la longueur du tuyau d’alimentation ne suffit pas, s’adresser à un magasin spécialisé ou à un technicien agréé.
! N’utiliser que des tuyaux neufs.
! Utiliser ceux qui sont fournis avec l’appareil.
14
65 - 100 cm
Raccordement du tuyau de vidange
Raccorder le tuyau d’évacuation, sans le plier, à un conduit d’évacuation ou à une évacuation murale pla­cés à une distance du sol comprise entre 65 et 100 cm;
! N’utiliser ni rallonges ni prises multiples.
! Le câble ne doit être ni plié ni trop écrasé.
! Le câble d’alimentation ne doit être remplacé
que par des techniciens agréés.
Attention! Nous déclinons toute responsabilité en cas de non-respect des normes énumérées ci-dessus.
Premier cycle de lavage
FR
ou bien l’accrocher à un évier ou à une bai­gnoire, dans ce cas, fixer le support en pla­stique fourni avec l’ap­pareil au robinet (voir figure). L’extrémité libre du tuyau d’évacuation ne doit pas être plon­gée dans l’eau.
! L’utilisation d’un tuyau de rallonge est abso­lument déconseillée mais si on ne peut faire autrement, il faut absolument qu’il ait le même diamètre que le tuyau original et sa longueur ne doit pas dépasser 150 cm.
Branchement électrique
Avant de brancher la fiche dans la prise de cou­rant, s’assurer que:
• la prise est bien reliée à la terre et est conforme aux réglementations en vigueur;
• la prise est bien apte à supporter la puissance maximale de l’appareil indiquée dans le tableau des Caractéristiques techniques (voir ci-contre);
• la tension d’alimentation est bien comprise entre les valeurs figurant dans le tableau des Caractéristiques techniques (voir ci-contre);
• la prise est bien compatible avec la fiche du lave­linge. Autrement, remplacer la prise ou la fiche.
! Le lave-linge ne doit pas être installé dehors, même à l’abri, car il est très dangereux de le laisser exposé à la pluie et aux orages.
! Après installation du lave-linge, la prise de courant doit être facilement accessible.
Avant la première mise en service de l’appareil, ef­fectuer un cycle de lavage avec un produit lessiviel mais sans linge et sélectionner le programme 2.
Caractéristiques techniques
Modèle
Dimensions
Capacité Raccordements
électriques
Raccorde­ments hydrau­liques
Vitesse d'essorage
Pr o gr am me s de contrôle se­lon les directi­ves 1061/2010 et 1015/2010
IWD 71052 largeur 59,5 cm
hauteur 85 cm profondeur 53,5 cm
de 1 à 7 kg Voir la plaque signalétique
appliquée sur la machine pression maximale
1 MPa (10 bar) pression minimale 0,05 MPa (0,5 bar) capacité du tambour 52 litres
jusqu'à 1000 tours minute
programme 2; programme coton standard à 60°C. programme 3; programme coton standard à 40°C.
Cet appareil est confor­me aux Directives Com­munautaires suivantes:
- 2004/108/CE (Compati­bilité électromagnétique)
- 2012/19/EU
- 2006/95/CE (Basse Tension)
15
Loading...
+ 33 hidden pages