Instructions for use
WASHING MACHINE
GB |
|
DE |
|
PL |
|
|
|
|
|
|
|
English,1 |
Deutsch,13 |
Polski,25 |
Contents |
GB |
|
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
EWSD 61253
Care and maintenance, 4
Cutting off the water or electricity supply Cleaning the washing machine
Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Description of the washing machine and starting a wash cycle, 6-7
Control panel Indicator lights Starting a wash cycle
Wash cycles, 8
Table of wash cycles
Fast daily cycles
Personalisation, 9
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 10
Detergent dispenser drawer Preparing the laundry Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
1
Installation
! This instruction manual should be kept in a safe GB place for future reference. If the washing machi-
ne is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/herself with its operation and features.
! Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance.
Unpacking and levelling
Unpacking
1.Remove the washing machine from its packaging.
2.Make sure that the washing machine has not been damaged during the transportation process. If it has been damaged, contact the retailer and do not proceed any further with the installation process.
3.Remove the 4 pro-
tective screws (used during transportation) and the rubber washer with the corresponding spacer, located on the rear part of the appliance (see figure).
4.Close off the holes using the plastic plugs provided.
5.Keep all the parts in a safe place: you will need them again if the washing machine needs to be moved to another location.
! Packaging materials should not be used as toys for children.
Levelling
1. Install the washing machine on a flat sturdy floor, without resting it up against walls, furniture cabinets or anything else.
2. If the floor is not perfectly level, compensate for any unevenness by tightening
or loosening the adjustable front feet (see figure); the angle of inclination, measured in relation to the worktop, must not exceed 2°.
Levelling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or a rug, adjust the feet in such a way as to allow a sufficient ventilation space underneath the washing machine.
Connecting the electricity and water supplies
Connecting the water inlet hose
|
|
|
|
|
|
1. Insert seal A into |
|
|
|
|
|
|
the end of the inlet |
|
|
|
|
|
|
hose and screw the |
|
|
|
|
|
|
latter onto a cold wa- |
|
|
|
|
|
A |
ter tap with a 3/4 gas |
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
threaded mouth (see |
|
|
|
|
|
|
|
figure). Before making |
|
|
|
|
|
|
the connection, allow |
|
|
|
|
|
|
|
|
|
|
|
|
|
the water to run fre- |
|
|
|
|
|
|
ely until it is perfectly |
|
|
|
|
|
|
clear. |
|
|
|
|
|
|
2. Connect the inlet |
|
|
|
|
|
|
|
|
|
|
|
|
|
hose to the washing |
|
|
|
|
|
|
machine by screwing |
|
|
|
|
|
|
it onto the correspon- |
|
|
|
|
|
|
ding water inlet of the |
|
|
|
|
|
|
appliance, which is |
|
|
|
|
|
|
situated on the top |
|
|
|
|
|
|
right-hand side of the |
|
|
|
|
|
|
rear part of the ap- |
|
|
|
|
|
|
pliance (see figure). |
|
|
|
|
|
|
3. Make sure that the hose is not folded over or bent.
!The water pressure at the tap must fall within the values indicated in the Technical details table (see next page).
!If the inlet hose is not long enough, contact a specialised shop or an authorised technician.
!Never use second-hand hoses.
!Use the ones supplied with the machine.
2
Connecting the drain hose
65 - 100 cm |
Connect the drain hose, without bending it, to a drainage duct or a wall drain located at a height between 65 and 100 cm from the floor;
alternatively, rest it on the side of a washbasin or bathtub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater.
! We advise against the use of hose extensions; if it is absolutely necessary, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity socket, make sure that:
•the socket is earthed and complies with all applicable laws;
•the socket is able to withstand the maximum power load of the appliance as indicated in the Technical data table (see opposite);
•the power supply voltage falls within the values indicated in the Technical data table
(see opposite);
•the socket is compatible with the plug of the washing machine. If this is not the case, replace the socket or the plug.
!The washing machine must not be installed outdoors, even in covered areas. It is extremely dangerous to leave the appliance exposed to rain, storms and other weather conditions.
!When the washing machine has been installed, the electricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
GB
!The cable should not be bent or compressed.
!The power supply cable must only be replaced by authorised technicians.
Warning! The company shall not be held responsible in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, using the wash cycle 2.
Technical data
Model |
EWSD 61253 |
|||
|
|
|
|
|
|
|
|
width 59.5 cm |
|
Dimensions |
height 85 cm |
|||
|
|
|
depth 42 cm |
|
Capacity |
from 1 to 6 kg |
|||
|
|
|
|
|
Electrical |
please refer to the technical |
|||
data plate fixed to the ma- |
||||
connections |
||||
chine |
||||
|
|
|
maximum pressure 1 MPa |
|
Water con- |
(10 bar) |
|||
minimum pressure 0.05 |
||||
nection |
||||
MPa (0.5 bar) |
||||
|
|
|
||
|
|
|
drum capacity 40 litres |
|
Spin speed |
up to 1200 rotations per |
|||
minute |
||||
|
|
|
||
Test wash |
|
|||
cycles in |
Programme 15: |
|||
accordance |
||||
with re- |
Eco Cotton 60°C. |
|||
gulations |
Programme 15: |
|||
1061/2010 |
Eco Cotton 40°C. |
|||
and |
|
|||
1015/2010 |
|
|||
|
|
|
This appliance conforms to |
|
|
|
|
the following EC Directives: |
|
|
|
|
- 2004/108/EC (Electroma- |
|
|
|
|
gnetic Compatibility) |
|
|
|
|
- 2012/19/EU - WEEE |
|
|
|
|
- 2006/95/EC Low Voltage) |
|
|
|
|
|
3
Care and maintenance
GB |
Cutting off the water and electri- |
|
city supplies |
||
|
||
|
• Turn off the water tap after every wash cycle. |
|
|
This will limit wear on the hydraulic system |
|
|
inside the washing machine and help to pre- |
|
|
vent leaks. |
|
|
• Unplug the washing machine when cleaning |
|
|
it and during all maintenance work. |
|
|
Cleaning the washing machine |
|
|
The outer parts and rubber components of the |
|
|
appliance can be cleaned using a soft cloth |
|
|
soaked in lukewarm soapy water. Do not use |
|
|
solvents or abrasives. |
|
|
Cleaning the detergent dispenser |
|
|
drawer |
|
|
Remove the dispenser |
|
|
by raising it and pul- |
|
|
ling it out (see figure). |
|
|
Wash it under running |
|
|
water; this operation |
|
|
should be repeated |
|
|
frequently. |
2. unscrew the lid by rotating it anticlockwise (see figure): a little water may trickle out. This is perfectly normal;
3.clean the inside thoroughly;
4.screw the lid back on;
5.reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are any cracks, it should be replaced immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.
! Never use second-hand hoses.
Caring for the door and drum of your appliance
•Always leave the porthole door ajar in order to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-clea- ning pump which does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber which protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and unplug the appliance.
To access the pre-chamber:
1. using a screwdriver, remove the cover panel on the lower front part of the washing machine (see figure);
4
Precautions and tips
! This washing machine was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully.
Consumers should contact their local authority or
retailer for information concerning the correct GB disposal of their old appliance.
General safety
•This appliance was designed for domestic use only.
•This appliance can be used by children aged
from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
•Do not touch the machine when barefoot or with wet or damp hands or feet.
•Do not pull on the power supply cable when unplugging the appliance from the electricity socket. Hold the plug and pull.
•Do not open the detergent dispenser drawer while the machine is in operation.
•Do not touch the drained water as it may reach extremely high temperatures.
•Never force the porthole door. This could damage the safety lock mechanism designed to prevent accidental opening.
•If the appliance breaks down, do not under any circumstances access the internal mechanisms in an attempt to repair it yourself.
•Always keep children well away from the appliance while it is operating.
•The door can become quite hot during the wash cycle.
•If the appliance has to be moved, work in a group of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy.
•Before loading laundry into the washing machine, make sure the drum is empty.
Disposal
•Disposing of the packaging materials: observe local regulations so that the packaging may be re-used.
•The European Directive 2012/19/EU - WEEE on Waste
Electrical and Electronic Equipment, requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected.
5
Description of the washing machine and starting a wash cycle
|
|
|
|
|
|
|
|
|
|
|
|
Control panel |
|
|
|
|
|
||
GB |
|
WASH CYCLE |
|||||||
|
|
||||||||
|
|
|
DELAY TIMER |
||||||
|
|
|
|
PROGRESS |
|||||
|
|
|
|
button |
|
||||
|
|
|
|
FUNCTION |
|
|
START/ |
||
|
|
|
DISPLAY |
|
|
||||
|
|
ON/OFF button |
|
|
PAUSE |
||||
|
|
|
|
buttons with |
|
|
|||
|
|
|
|
|
indicator lights |
|
|
button with |
|
|
|
|
|
|
|
|
indicator light |
||
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TEMPERATURE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DOOR LOCKED |
||
|
|
|
knob |
|
||
Detergent dispenser drawer |
|
|
||||
WASH CYCLE |
SPIN SPEED |
indicator light |
||||
|
|
|
|
|||
|
|
knob |
|
knob |
|
|
Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”).
ON/OFF button: switches the washing machine on and off.
WASH CYCLE knob: programmes the wash cycles. During the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the available functions. The indicator light corresponding to the selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold wash cycle (see “Personalisation”).
SPIN SPEED knob: sets the spin speed or exclude the spin cycle completely (see “Personalisation”).
DISPLAY: used to view the duration of the various cycles available and the remaining time of a cycle in progress;
if the DELAY TIMER option has been selected, the countdown to the start of the selected cycle will appear.
DELAY TMER button : press to set a delayed start time for the selected wash cycle. The delay time will be shown on the display.
WASH CYCLE PROGRESS indicator lights: used to monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in progress.
DOOR LOCKED indicator light: indicates whether the door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or temporarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this button; the corresponding indicator light will flash orange, while the indicator light for the current wash cycle phase will remain lit in a fixed manner. If the DOOR LOCKED indicator light is switched off, the door may be opened (wait approximately 3 minutes).
To start the wash cycle from the point at which it was interrupted, press this button again.
Standby mode
This washing machine, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected. Press the ON-OFF button briefly and wait for the machine to start up again.
6
Indicator lights
The indicator lights provide important information. This is what they can tell you:
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has begun, the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress.
Wash
Rinse
Spin
Drain
End of wash cycle
Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator light will illuminate.
If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and the function will not be activated.
If the selected function is not compatible with another function which has been selected previously, the indicator light corresponding to the first function selected will flash and only the second function will be activated; the indicator light corresponding to the enabled option will remain lit.
Door locked indicator light
When the indicator light is on, the porthole door is locked to GB prevent it from being opened; make sure the indicator light is
off before opening the door (wait approximately 3 minutes). To open the door during a running wash cycle, press the START/PAUSE button; the door may be opened once the DOOR LOCKED indicator light turns off.
Starting a wash cycle
1.Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then they will switch off and the START/PAUSE indicator light will pulse.
2.Load the laundry and close the door.
3.Set the WASH CYCLE knob to the desired programme.
4.Set the washing temperature (see “Personalisation”).
5.Set the spin speed (see “Personalisation”).
6.Measure out the detergent and washing additives (see “Detergents and laundry”).
7.Select the desired functions.
8.Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the END indicator light will switch on. The door can be opened once the DOOR LOCK indicator light turns off (wait approximately 3 minutes). Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch the washing machine off by pressing the ON/OFF button.
7
Wash cycles
Table of wash cycles
GB
cycles |
|
Max. |
Max. |
|
Wash |
Description of the wash cycle |
temp. |
speed |
|
|
(°C) |
(rpm) |
||
|
|
|||
|
EVERYDAY FAST |
|
|
|
|
|
|
||
1 |
Colour Mix 59’ |
40° |
1000 |
|
2 |
Cotton 59’ |
60° |
1000 |
|
3 |
Cotton 45’ |
40° |
1200 |
|
4 |
Synthetics 59’ (3) |
40° |
1000 |
|
(Max. 60°) |
||||
|
|
|
||
5 |
Mix 30’ |
30° |
800 |
|
6 |
Express 20’ |
20° |
800 |
|
|
Special & Partial |
|
|
|
7 |
Gym Kit |
40° |
600 |
|
8 |
Sport Shoes |
30° |
600 |
|
9 |
Baby: Heavily soiled delicate colours. |
40° |
800 |
|
10 |
Rinse |
- |
1200 |
|
11 |
Spin + Drain |
- |
1200 |
|
11 |
Only Drain * |
- |
|
|
|
Dedicated |
|
|
|
|
|
|
||
12 |
Duvet: for down-stuffed garments. |
30° |
1000 |
|
13 |
Wool: for wool, cashmere, etc. |
40° |
800 |
|
14 |
Silk/Curtains: for garments in silk and viscose, lingerie. |
30° |
0 |
|
15 |
Eco Cotton 60° (1): heavily soiled whites and resistant colours. |
60° |
1200 |
|
15 |
Eco Cotton 40° (2): lightly soiled whites and delicate colours. |
40° |
1200 |
|
16 |
Cotton with prewash: extremely soiled whites. |
90° |
1200 |
|
|
|
|
|
*If you select programme 11 and exclude the spin cycle, the machine will drain only.
**The duration of the wash cycle can be checked on the display.
Pre-wash |
|
Wash |
|
softener |
Max. (kg)load |
Residual %dampness |
Energy consumption kWh |
waterTotallt |
Cycle duration |
|
Detergents |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fabric |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- |
|
|
|
|
|
|
|
|
59’ |
|
|
6 |
- |
- |
- |
||||
- |
|
|
|
|
6 |
- |
- |
- |
59’ |
- |
|
|
|
|
3 |
- |
- |
- |
45’ |
- |
|
|
|
|
3 |
44 |
0,72 |
36 |
59’ |
- |
|
|
|
|
3 |
71 |
0,16 |
27 |
30’ |
- |
|
|
|
|
1,5 |
- |
- |
- |
20’ |
- |
|
|
|
|
|
|
|
|
|
|
|
2,5 |
- |
- |
- |
** |
|||
- |
|
|
|
|
Max. 1 |
- |
- |
- |
** |
|
|
pairs |
|||||||
|
|
|
|
|
|
|
|
|
|
- |
|
|
|
|
2 |
- |
- |
- |
** |
- |
|
- |
|
|
6 |
- |
- |
- |
** |
- |
|
- |
|
- |
6 |
- |
- |
- |
** |
- |
|
- |
|
- |
6 |
- |
- |
- |
** |
- |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
1 |
- |
- |
- |
** |
|||
- |
|
|
|
|
1 |
- |
- |
- |
** |
- |
|
|
|
|
1 |
- |
- |
- |
** |
- |
|
|
|
|
6 |
53 |
0,80 |
50,0 |
200’ |
- |
|
|
|
|
6 |
53 |
0,65 |
66 |
170’ |
|
|
|
|
|
6 |
- |
- |
- |
** |
|
|
|
|
|
|
|
|
|
|
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 15 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 15 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2)Long wash cycle for cottons: set wash cycle 15 with a temperature of 40°C.
3)Long programme for synthetics: set programme 4, then select the “Extra Wash ” option.
Fast daily cycles
A complete set of fast programmes to wash the most commonly used fabrics - even with a full load - and to remove the most frequent daily dirt in less than 1 hour.
Colour Mix 59’: to wash mixed and coloured items together.
Cotton 59’: cycle designed to wash cotton garments - mainly white items. It can be used with powder detergent too. Cotton 45’: short cycle designed to wash delicate cotton items.
Synthetics 59’: specific for synthetic items. If the dirt is difficult to remove, the temperature can be increased up to 60° and powder detergent can be used too.
Mix 30’: short cycle designed to wash a mixed load of cotton and synthetic fabrics - white and coloured items together. Express 20’: this programme refreshes your items, making them perfumed again in just 20 minutes.
8
Personalisation
|
|
|
|
|
|
Setting the temperature |
|
|
|
||
|
|
GB |
|||
Turn the TEMPERATURE knob to set the wash temperature (see |
Table of wash cycles). |
||||
|
|||||
The temperature may be lowered, or even set to a cold wash . |
|
|
|
||
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value |
|
||||
set for each wash cycle. |
|
|
|
||
! Exception: if the 4 programme is selected, the temperature can be increased up to a value of 60°C. |
|
||||
Setting the spin speed |
|
|
|
||
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle. |
|
||||
The maximum spin speeds available for each wash cycle are as follows: |
|
||||
Wash cycles |
Maximum spin speed |
|
|
|
|
Cottons |
1200 rpm |
|
|
|
|
Synthetics |
1000 rpm |
|
|
|
|
Wool |
800 rpm |
|
|
|
|
Silk |
drain only |
|
|
|
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time. To activate the functions:
1.Press the button corresponding to the desired function;
2.the function is enabled when the corresponding indicator light is illuminated.
Note:
-If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and the function will not be activated.
-If the selected function is not compatible with another function which has been selected previously, the indicator light corresponding to the first function selected will flash and only the second function will be activated; the indicator light corresponding to the enabled option will remain lit.
Delay timer
To set a delayed start for the selected programme, press the corresponding button repeatedly until the required delay period has been reached. When this option is enabled, the symbol lights up on the display. To remove the delayed start option press the button until the text “OFF” appears on the display.
Extra Wash
Enable the Extra Wash option for very dirty items, where compatible. Press this option to let the cycle automatically re-adjust all wash parameters through a longer lasting cycle. The option always leaves the temperature unchanged, while the spin cycle is automatically brought back to maximum levels. The user can set the spin cycle back to the desired value at any time.
The option washes cotton and synthetic items, saving energy and helping the environment. Energy saving is due to a cold wash cycle, while an enhanced mechanical action and optimised water use make it possible to reach the desired result. Recommended for slightly soiled garments. Use of liquid detergent recommended.
9
Detergents and laundry
Detergent dispenser drawer
GB
Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause build up on the inside of your appliance and contribute to environmental pollution.
!Do not use hand washing detergents because these create too much foam.
!Use powder detergent for white cotton garments, for prewashing, and for washing at temperatures over 60°C.
!Follow the instructions given on the detergent packaging.
Open the detergent dispenser drawer and pour in the detergent or washing additive, as follows.
3
1 2
compartment 1: Pre-wash detergent (powder) compartment 2: Detergent for the wash cycle (powder or liquid)
Liquid detergent should only be poured in immediately prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Note: If a “tablet detergent” is used, always follow the manufacturer’s instructions.
Preparing the laundry
•Divide the laundry according to:
-the type of fabric/the symbol on the label
-the colours: separate coloured garments from whites.
•Empty all garment pockets and check the buttons.
•Do not exceed the values listed in the “Table of wash cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Special wash cycles
Gym Kit: cycle suitable to wash all sports items together, including gym towels, while respecting their fibres (follow the
instructions in the garment labels).
Sport Shoes: is for washing sports shoes; for best results, do not wash more than 1 pairs simultaneously.
We recommend fastening any strings before introducing the shoes into the drum.
Baby: cycle designed for dirt typical of children’s garments in that it effectively removes any traces of residual detergent.
Duvet: to wash single duvets (the weight of which should not exceed 1 kg), cushions or clothes padded with goose down such as puffa jackets, use the special wash cycle number 12. We recommend that duvets are placed in the drum with their edges folded inwards (see figure) and that no more than ¾ of the total volume of the drum is used. To achieve the best results, we recommend that a liquid detergent is used and placed inside the detergent dispenser drawer.
Wool: all wool garments can be washed using programme 13, even those carrying the “hand-wash only” label. For best results, use special detergents and do not exceed 1 kg of laundry.
Silk: use special wash cycle 14 to wash all silk garments. We recommend the use of special detergent which has been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or mesh bag. Use wash cycle 14.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and to distribute the load in a uniform manner, the drum rotates continuously at a speed which is slightly greater than the washing rotation speed. If, after several attempts, the load is not balanced correctly, the machine spins at a reduced spin speed. If the load is excessively unbalanced, the washing machine performs the distribution process instead of spinning. To encourage improved load distribution and balance, we recommend small and large garments are mixed in the load.
10
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure |
GB |
that the problem cannot be not solved easily using the following list. |
Problem:
The washing machine does not switch on.
The wash cycle does not start.
The washing machine does not take in water (“H2O” will flash on the display).
Possible causes / Solutions:
•The appliance is not plugged into the socket fully, or is not making contact.
•There is no power in the house.
•The washing machine door is not closed properly.
•The ON/OFF button has not been pressed.
•The START/PAUSE button has not been pressed.
•The water tap has not been opened.
•A delayed start has been set (see “Personalisation”).
•The water inlet hose is not connected to the tap.
•The hose is bent.
•The water tap has not been opened.
•There is no water supply in the house.
•The pressure is too low.
•The START/PAUSE button has not been pressed.
The washing machine continuously • The drain hose is not fitted at a height between 65 and 100 cm from the floor takes in and drains water. (see “Installation”).
•The free end of the hose is under water (see “Installation”).
•The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the appliance off and contact the Assistance Service. If the dwelling is on one of the upper floors of a building, there may be problems relating to water drainage, causing the washing machine to fill with water and drain continuously. Special anti-draining valves are available in shops and help to avoid this inconvenience.
The washing machine does not drain or spin.
•The wash cycle does not include draining: some wash cycles require the drain phase to be started manually.
•The drain hose is bent (see “Installation”).
•The drainage duct is clogged.
The washing machine vibrates a lot • The drum was not unlocked correctly during installation (see “Installation”). during the spin cycle. • The washing machine is not level (see “Installation”).
• The washing machine is trapped between cabinets and walls (see “Installation”).
The washing machine leaks. • The water inlet hose is not screwed on properly (see “Installation”).
•The detergent dispenser drawer is blocked (for cleaning instructions, see “Care and maintenance”).
•The drain hose is not fixed properly (see “Installation”).
The “function” indicator lights and the “start/pause” indicator light flash, while one of the “phase in progress” indicator lights and the “door locked” indicator light will remain lit in a fixed manner.
•Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
There is too much foam. • The detergent is not suitable for machine washing (it should display the text
“for washing machines” or “hand and machine wash”, or the like).
• Too much detergent was used.
11