Indesit DI 6 User Manual

User

Instruction

Book

for

INDESIT

Dishwasher

Model:

DI 6

.

Safety Is a Good Habit to Get Into

NOTICE
Carefully read the instructions contained in this manual, as
they provide important information which is essential to
safe and proper installation, use and maintenance of the
appliance.

This appliance complies with the following EEC
directives:

- 73/23/EEC (Low Voltage) and subsequent
modifications;

- 89/336/EEC (Electromagnetic Compatibility) and
subsequent modifications.

- 97/17/EEC (Labelling)

1.Carefully dispose of the packing material.

2.After removing the packing, check to make sure that

the appliance is not damaged. If in doubt, contact a
qualified professional.

3.The dishwasher must only be used by adults for the
washing of household dishes and cooking utensils.

4.Fundamental rules to follow when using the appliance:

- Never touch the dishwasher when barefoot or with wet
hands or feet;

- We discourage the use of extension cords and multiple
sockets;

- During installation, the power supply cord must not be
excessively or dangerously bent or flattened;

- If the appliance is not operating properly or maintenance
must be performed, disconnect the appliance from the power
supply .

5.Keep detergents out of the reach of children, who must
also be kept away from the dishwasher when it is open.

6.This appliance cannot be installed outdoors, not even if
the area in which it is installed is covered by a roof; it is also
very dangerous to leave it exposed to the rain and elements.

7.Do not touch the heating element during or after a wash
cycle.

8.Do not lean or sit on the door when it is open, as this could
overturn the dishwasher .

9.If the appliance malfunctions, turn off water supply to the
appliance and disconnect the plug from the wall socket.
Then, consult the section entitled, "T roubleshooting." If you
cannot resolve the problem, contact a service centre.

10.Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing
the door lock.

To maintain the EFFICIENCY and SAFETY of this
appliance, we recommend:

l call only the Service Centers authorized

by the manufacturer

l always use original Spare Parts

Close-up View (control panel)

1

ON-OFF Button

ON - OFF Light

Cycles Indicator Lights

C

2

P

34

Cycles Indicator Lights

P

B

Cycle select button

A

11

GB

Close-up View (Interior)

G

J

I

E

F

H

K

L

Upper Rack

T op Sprayer Arm

Rack Height Adjustor

Lower Rack

Bottom Sprayer Arm

Salt Container Cap

Washing Filter

Detergent and Rinse Aid Dispenser

Technical characteristics

Width cm. 59,5
Depth cm. 57
Height cm. 82
Capacity 12 standard place settin gs
Mains water pressure 30 KPa÷ 1MPa (0,3 ÷10 bar)

Power voltage See data plate

Total absorber power See data plate
Fuse See data plate

GB

12

Salt .......

Salt

The hardness of the water varies from place to place. If
hard water is used in the dishwasher, deposits will form on
the dishes and utensils.
The appliance is equipped with a special softener that uses
a salt specifically designed to eliminate lime and minerals
from the water.

Loading the Salt into the Softener

Always use salt intended for use with dishwashers.
The salt container is
located beneath the lower
rack and should be filled
as follows:

1. Remove the lower rack
and then unscrew and
remove the cap from the
salt container;

2. If you are filling the
container for the first time,
fill it with water;

3. Place the end of the
funnel (supplied) into the
hole and introduce about
2 kg of salt. It is normal for a small amount of water to
come out of the salt container .

4. Carefully screw the cap back on.

The salt container should be filled after about every
30 wash cycles.

Adjusting Salt Consumption

The dishwasher is designed to allow for adjusting the amount
of salt consumed based on the
harness of the water used. This
is intended to optimize and cus­tomize the level of salt con­sumption so that it remains at a
minimum.
Your Local Water Board can
supply the degree of hardness
of the water
in your area.
T o adjust salt consumption, pro­ceed as follows:

1) Unscrew the cap from the salt container.

2) There is a ring on the container with an arrow on it (see
figure to the side), if necessary, rotate the ring in the anti­clockwise direction from the "_" setting towards the "+"
sign, based on the hardness of the water being used.
It is recommended that adjustments be made in accord­ance with the following schema:

Water Hardness

Salt

Autono­my

(cycles\2­kg)

Clarke

degrees

°fH mmol/l

Selector
position

consu­mption

(grams/ ­cycle)

To prevent the formation of rust, load the salt just before
beginning a wash cycle.

0 - 14 0 - 17 0 -1,7 / 0 /

14 - 36 18 - 44 1,8 - 4,4 "-" 20 60

36 - 71 45 - 89 4,5 - 8,9 MED 40 40

>71 >89 > 8,9 "+" 60 25

13

GB