TWIST-5LED
Best.-Nr. 38.5980
LED MOVING HEAD
LYRE À LED
MOVING-HEAD A LED
BEDIENUNGSANLEITUNG • INSTRUCTION MANUAL • ISTRUZIONI PER L’USO
VEILIGHEIDSVOORSCHRIFTEN • SIKKERHEDSOPLYSNINGER
SÄKERHETSFÖRESKRIFTER • TURVALLISUUDESTA
1
2
2
4
4
6
6
7
7
7
8
8
8
11
11
12
13
13
14
14
14
14
14
14
15
15
15
15
15
16
16
18
19
19
20
20
20
20
20
22
TWIST-5LED Product Guide
Warning.................................................................................…...……………..…………………………….…………
Safety-instructions………………………………………………………………………………………………………
Operating Determinations.…………………………………………………………………………………………..
Rigging.……………………………………………………………………………………………………………………
Return Procedure…………………………………………………………………………….....................................
.
Description...............................................................................…...………………………………………….………..
Features and Overview ………………………………...….……………….………….……….……….……………
Backside…………………………………………………...…...….……………….…………………...……………….
Installation...............................................................................…...…………………………………………………….
Set Up and Operation.....................................................................……..……………………………………………
Control Modes…………………………………………………………………………………………………….…….
One TWIST-5LED (Built-in Programs)…..…………………………….……………….…………..…..…………..
One TWIST-5LED (Sound Control)…………………………………………..…………………….……..……….
Multiple TWIST-5LEDs (Master/Slave control).……………………………………………….....………………
Multiple TWIST-5LEDs (DMX control)………………………………………………….…..………..…………….
Fixture Linking…………………............……..……………………………………..…………………..…………..…..
Control Panel….............……....................................………………………………………………………….……..
Control Mode........................................……………………………………………………………………….……..
DMX addressing...................................………………………………………………………………………….……
MENU OVERVIEW ……..……………………………………..…………………………………….…….……….….....
Main Menu Options.……………………………………..…………………………………….…….……………
DMX Addressing.……………………………………..…………………………………….…….………………..
Built-in Programs Mode.……………………………………..…………………………………….……….…….
Pan movement Mode.……………………………………..…………………………………….…….……..…
Tilt movement Mode.…………………..…………………..…………………………………….…….……..….
Display Mode.………………………………………………..…………………………………….…….……..….
Advanced/Basic Mode…………………………………..…………………………………….………………..
Pan Mode…………………………………..…………………………………….…….…………………………..
Tilt Mode…………………………………..…………………………………….…….…………………………….
Reset…………………………………..…………………………………….…….…………………………………
Default Settings…………………………………..…………………………………….…………………….……
Password change…………………………………………………………………………………………………
Service Functions…………………………………………………………………………………………………..
DMX Channels………………………………………………………………………………...…………………………
13 Channels (ADVANCED) ……………………………………………………...………………………………
8 Channels (BASIC)…….…………………………………………………………………………….……………
Channel settings…………………………..…………………………………………………………………………….
Maintenance...................................................................................………..………….…….……………………..….
Replacing the Fuse........................................................................…………………….…………………………..
Rotating Gobowheel and Colorwheel……………….…………………..…………………………………………
Troubleshooting............................................................................………………….………………….………………
No Light, No Movement - All Products............................................………………….………………………….
No Response to DMX ....................................................................………………….…………………………….
Product Specifications.................................................................……………….…….………………………………
6
8
9
10
11
2
WARNING
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
• IMG Stage Line TWIST-5LED Spot with IEC powercable 0,9m
• 1 bracket for truss mounting
• Safety eye
• User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. It is estimated that a viable lifespan of 40,000 to 50,000 hours will be achieved
under normal operational conditions. If improving on this lifespan expectancy is of a higher priority, place
care in providing for lower operational temperatures. This may include climatic-environmental and the
reduction of overall projection intensity.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation and maintenance of this device has to:
- be qualified
- follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
CAUTION! Be careful with your operations.
With a dangerous voltage you can suffer
a dangerous electric shock when touching the wires!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
3
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the nonobservance of this manual or any unauthorized modification to the device.
Never let the power-cord come into contact with other cables! Handle the power-cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged.
Always hold the fixture at the transport handles.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Never unscrew the screws of the rotating gobo, as the ball bearing will otherwise be opened.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this would reduce the device’s life.
Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the fixture to cool for at least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoor, avoid contact with water or other liquids.
Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always allow free air space of at least 50 cm around the unit for ventilation.
Always disconnect power from the mains, when device is not used or before cleaning! Only
handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power-cord is never crimped or damaged. Check the device and the power-
cord from time to time.
If the lens is obviously damaged, it has to be replaced. So that its functions are not impaired, due
to cracks or deep scratches.
If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do
not switch it on immediately. The arising condensation water might damage your device. Leave
the device switched off until it has reached room temperature.
If your IMG Stage Line device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your dealer for service.
For adult use only. Movinghead must be installed out of the reach of children. Never leave the
unit running unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the TWIST-5LED. The manufacturer will
not accept liability for damages caused by the misuse or incorrect installation of this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
During the initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective.
Repairs, servicing and electric connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.
CAUTION ! EYEDAMAGES !.
Avoid looking directly into the light source.
(meant especially for epileptics) !
4
OPERATING DETERMINATIONS
• This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
• The minimum distance between light-output and the illuminated surface must be more than 1 meter.
• The maximum ambient temperature ta = 45°C must never be exceeded.
• If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
• Any other operation may lead to dangers like short-circuit, burns, electric shock, lamp explosion, crash
etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all other
safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
If the projector is lowered from the ceiling or high joists, professional trussing systems have to be
used.
Use a clamp to mount the projector, with the mounting-bracket, to the trussing system.
The projector must never be fixed swinging freely in the room.
The installation must always be secured with a safety attachment, e.g. an appropriate safety net
or safety-cable.
When rigging, derigging or servicing the projector, always make sure, that the area below the
installation place is blocked and staying in the area is forbidden.
The TWIST-5LED can be placed on a flat stage floor or mounted to any kind of truss by a clamp.
5
Mounting a clamp to the underside of the TWIST-5LED moving head
Improper installation can cause serious damage to people and property !
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
FASE
N
BLUE
BLACK
SILVER
NUL
YELLOW/GREEN
GREEN
GREEN
EARTH
Make sure that the device is always connected properly to the earth!
6
Description of the device
Features
The IMG Stage Line TWIST-5LED Spot is a moving-head with high output and great effects.
• DMX-control via standard DMX-controller
• Built-in Automatic Programs + Built-in Sound activated programs
• User-selectable Pan & Tilt ranges, 540° / 360° / 180°
• Reverse Pan / Tilt movement
• Special: Pan / Tilt movement blackout
• Pan 0º -- 540º
• Tilt 0º -- 270º
• Pan/Tilt resolution: 16 bit
• Control: DMX-512, Master/Slave, Sound-controlled
• 16 Built in programs selectable by DMX
• Light Source: 1 x 50W White LED
• Colourwheel with 8 dichroic-colours and white
• Color functions: Split colors, Rainbow-flow effect
• Rotating Gobowheel with 2 glass gobos, 5 metal gobos and open with Gobo Shake Function
• Rotation: Bi-directional
• Prism: 3-facet prism
• Gobo functions: Gobo-flow effect, Gobo shake
• 8 automatic and 8 sound-to-light programs with master / slave function
• Single clamp bracket, which makes it easy to handle and position in truss systems.
• Output: 18.500 Lux @ 1m.
• Beam Angle: 17°
• Input Voltage: 100-240 VAC
• Peak Power 227 Watt; Continuous Power 185 Watt
• Dimmer: 0-100%
• Strobe: 0-20Hz
• Focus: Manual focus
• Housing: Black Metal & Flame-retardant plastic
• Fixture Connection: XLR Data in/out (XLR 3-pin), IEC Power in
• Fuse F2A / 250V
• Weight: 5,64 kg
• User selectable Basic (8CH) or Advanced (13CH) operating modes
Overview
1) Lens
2) Menu Buttons + LCD Display
1
1
Fig. 1
2
7
Backside
Fig. 2
3 4 5 6
3) IEC power connector
4) Fuse F2A 250V
5) DMX signal connector (IN) 3-pin
6) DMX signal connector (OUT) 3-pin
Installation
Remove all packing materials from the TWIST-5LED Spot. Check that all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply. The device can be music-controlled by its built-in
microphone.
8
Control Modes
There are 4 modes: • Stand-alone (built-in programs)
• Sound-controlled
• Master/Slave
• DMX512 (13 Channels ADVANCED or 8 channel BASIC)
One TWIST-5LED (Built-in Programs)
1. Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
2. When the TWIST-5LED is not connected by a DMX-cable, it functions as a stand-alone device.
Please see page 15 for more information about the built-in programs.
One TWIST-5LED (Sound-control)
1.Plug the end of the electric mains power cord into a proper electric power supply socket.
2. Turn on the music. If the device is set to sound-control, then the TWIST-5LED will react to the beat of the
music. Please see page 15 for more information about the sound-control options.
Multiple TWIST-5LEDs (Master/Slave control)
1. Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
2. Use a 3-p XLR cable to connect the TWIST-5LED.
The pins:
1. Earth
2. Signal -
3. Signal +
3. Link the units as shown in (Fig. 3), Connect a DMX signal cable from the first unit's DMX "out"
socket to the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.
You can use the same functions on the master device as described on page 15 (Built-in Programs,
or Music control). This means on the master device you can set your desired operation Mode
and all slave devices will react the same as the master device.
Multiple TWIST-5LEDs (Master/Slave control)
Fig. 3
9
Multiple TWIST-5LEDs (DMX Control)
1. Fasten the effect light onto firm trussing Leave at least 1 meter on all sides for air circulation.
2. Always use a safety cable.
3. Use a 3-p XLR cable to connect the TWIST-5LEDs and other devices.
4. Link the units as shown in (figure 4), Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.
5. Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains power cord into proper electric power supply sockets, starting with the first unit.
Do not supply power before the whole system is set up and connected properly.
Multiple TWIST-5LEDs DMX Set Up
Note : Link all cables before connecting electric power
Fig. 4
10
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of TWIST-5LEDs on a DMX data link: 30 fixtures
The TWIST-5LED Spot can be operated with a controller in control mode or without the controller in
stand-alone mode.
11
Control Panel
Fig. 5
A. LCD Display D. Down Button
B. MODE/ESC button E. ENTER Button
C. Up Button
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address the next time.)
DMX Addressing
The control panel on the front side of the base allows you to assign the DMX fixture address, which is the
first channel from which the TWIST-5LED will respond to the controller.
Please note when you use the controller, the unit has 13 channels.
When using multiple TWIST-5LEDs, make sure you set the DMX addresses right.
Therefore, the DMX address of the first TWIST-5LED should be 1(001); the DMX address of the second TWIST-5LED
should be 1+13=14 (014); the DMX address of the third TWIST-5LED should be 14+13=27 (027), etc.
Please, be sure that you don’t have any overlapping channels in order to control each TWIST-5LED
correctly.
If two or more TWIST-5LEDs are addressed similarly, they will work similarly.
For address settings, please refer to the instructions under ”Addressing’.
Controlling:
After having addressed all TWIST-5LED fixtures, you may now start operating these via your lighting
controller.
Note: After switching on, the TWIST-5LED will automatically detect whether DMX 512 data is received or
not. If there is no data received at the DMX-input, the “LED “ on the control panel will not flash.
The problem may be:
- The XLR cable from the controller is not connected with the input of the TWIST-5LED.
- The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It’s necessary to insert a XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
12
Menu Overview
13
Main Menu Options
DMX address
Built-in Programs Slow/Fast/Sound-control/Remote control/Slave
Pan/Reverse Pan
Tilt/Reverse Tilt
Display/Reverse Display
Advanced 13 channels/ Basic 8 channels
Pan 540º, 360º, 180º
Tilt 270º, 180º, 90º
Reset
Load factory default settings
DMX Addressing
With this menu you can set the DMX address.
1) Press Mode/Esc, until the display shows .
2) Press Enter to confirm. You can choose 512 different DMX addresses.
Use the Up / Down buttons to select the required address from .
3) Once you have set the desired DMX address, press the enter button to store your DMX address.
14
Built-in Programs Mode
You can select 5 different Programs when using the Giant LED.
Press MODE until the display shows ,then press the UP / DOWN buttons to select all 5 programs.
Built-in Program Slow
When the display shows : ,then press ENTER. The display will show .
The device is now in a fast built-in program mode.
Built-in Program Fast
When the display shows : ,then press ENTER. The display will show .
The device is now in a slow built-in program mode.
Sound-controlled Mode
When the display shows : ,then press ENTER. The display will show .
The device is now sound-controlled and will react to the music.
Slave Mode
When the display shows : , then press ENTER. The display will show .
The device is now a slave device. It will now react the same as its master.
Pan movement Mode
When the display shows : , the device is in normal Pan Mode.
When you press Up/Down. The display will show . The Pan function is reversed.
Tilt movement Mode
When the display shows : , the device is in normal Tilt Mode.
When you press Up/Down. The display will show . The Tilt function is reversed.
Display Mode
When the display shows : , the device is in normal Display Mode.
When you press Up/Down. The display will show . The Display function is reversed.
Advanced/Basic Mode
When the display shows : , the device has 13 Channels.
When you press Up/Down. The display will show . The device now has 8 channels.
Pan Mode
When the display shows : , the Pan is 540º.
When you press Up/Down and the display shows , the Pan is 360º.
When you press Up/Down and the display shows , the Pan is 180º.
15
Tilt Mode
When the display shows : , the Tilt is 270º.
When you press Up/Down and the display shows , the Pan is 180º.
When you press Up/Down and the display shows , the Pan is 90º.
Reset
When the display shows : and you press ENTER the device will reset.
Default Settings
When the display shows : and you press ENTER the device will return to the factory default
settings.
Password Change
This is a Service Function.
Press and hold MODE/ESC for 2 seconds.
The display will show 0000.
Press the Up button to change the value. Press the Down button to go to the next digit.
Enter password: 2323.
A new menu will open, you can scroll through the menu with the MODE/ESC button.
Use the Up/Down buttons to change a certain value.
Press the ENTER button to store your setting. This option will auto-exit after 10 seconds.
Service Functions
This is a Service Function.
Press and hold MODE/ESC for 2 seconds.
The display will show 0000.
Press the Up button to change the value. Press the Down button to go to the next digit.
Enter password: 2322.
Use the Up/Down buttons to change a certain value.
Press the ENTER button to store your setting. This option will auto-exit after 10 seconds.
16
DMX Protocol 13 Channels ( )
Channel 1 – Horizontal movement (Pan)
Push the slider up, in order to move head horizontally (PAN).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
The head can be turned by 540° and stopped at any position you wish.
Channel 2 – Vertical movement (Tilt)
Push the slider, up in order to move head vertically (TILT).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
The head can be turned by 270° and stopped at any position you wish.
Channel 3 – Pan fine 16 bit
Channel 4 – Tilt fine 16 bit
Channel 5 – PAN/TILT Speed
0-255
From Max Speed (0) to Min. Speed (255)
Channel 6 – Colourwheel
Linear color change following the movement of the slider. Between 128 - 255, the color-wheel rotates
continuously the so-called “Rainbow” effect.
0-6
Open / White
7-13
Yellow
14-20
Pink
21-27
Green
28-34
Red
35-41
Light Blue
42-48
Light Green
49-55
Orange
56-64
Dark Blue
65-71
Split Color White / Yellow
72-78
Split Color Yellow / Pink
79-85
Split Color Pink / Green
86-92
Split Color Green / Red
93-99
Split Color Red / Light Blue
100-106
Split Color Light Blue / Light Green
107-113
Split Color Light Green / Orange
114-120
Split Color Orange / Dark Blue
121-127
Split Color Dark Blue / White
128-191
Clockwise rotation (CW) rainbow effect from slow to fast
192-255
Counter-clockwise rotation (CCW) rainbow effect from slow to fast
Channel 7 – Shutter / Strobe (Dimmer must be open )
0-3
Close
4-7
Shutter open
8-215
Strobe effect, from slow to fast (0-10 flashes/sec.)
216-255
Shutter open
Channel 8 – Dimmer intensity
0-255
From black to brightest
Channel 9 – Rotating Gobo-wheel + Gobo Shake
0-7
Open / White
8-15
Gobo 1 (Glass)
16-23
Gobo 2 (Glass)
24-31
Gobo 3 (Metal)
32-39
Gobo 4 (Metal)
40-47
Gobo 5 (Metal)
17
48-55
Gobo 6 (Metal)
56-63
Gobo 7 (Metal)
64-71
Gobo Shake 7 from slow to fast
74-79
Gobo Shake 6 from slow to fast
80-87
Gobo Shake 5 from slow to fast
88-95
Gobo Shake 4 from slow to fast
96-103
Gobo Shake 3 from slow to fast
104-111
Gobo Shake 2 from slow to fast
112-119
Gobo Shake 1 from slow to fast
120-127
Open / White
128-191
Clockwise rotation (CW) rainbow effect from slow to fast
192-255
Counter-clockwise rotation (CCW) rainbow effect from slow to fast
Channel 10 – Gobo rotation
0-7
No Rotation
8-119
Clockwise rotation (CW) from slow to fast
120-231
Counter-clockwise rotation (CCW) from slow to fast
232-255
Gobo bouncing
Channel 11 – Prism
0-15
Open
16-255
3-facet Prism Effect
Channel 12 – Channel Functions
0-7
No Function
8-27
Blackout during Pan/Tilt movement
28-47
Blackout during Gobowheel movement
48-67
Disabled blackout during Pan/Tilt/Gobowheel movement
68-87
Blackout during Colorwheel movement
88-107
Disabled blackout during Pan/Tilt/Colorwheel movement
108-127
Disabled blackout during Gobowheel /Colorwheel movement
128-147
Disabled blackout during Pan/Tilt/Gobowheel /Colorwheel movement
148-157
Reset Pan
158-167
Reset Tilt
168-177
Reset Colorwheel
178-187
Reset Gobowheel
188-197
Reset Prism
198-207
Reset All channels
208-255
No Function
Channel 13 – Built-in Programs + Sound-controlled Programs
0-7
No Function
8-23
Built-in Program 1
24-39
Built-in Program 2
40-55
Built-in Program 3
56-71
Built-in Program 4
72-87
Built-in Program 5
88-103
Built-in Program 6
104-119
Built-in Program 7
120-135
Built-in Program 8
136-151
Sound-controlled Program 1
152-167
Sound-controlled Program 2
168-183
Sound-controlled Program 3
184-199
Sound-controlled Program 4
200-215
Sound-controlled Program 5
216-231
Sound-controlled Program 6
232-247
Sound-controlled Program 7
248-255
Sound-controlled Program 8
18
DMX Protocol 8 Channels ( )
Channel 1 – Horizontal movement (Pan)
Push the slider up, in order to move head horizontally (PAN).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
The head can be turned by 540° and stopped at any position you wish.
Channel 2 – Vertical movement (Tilt)
Push the slider, up in order to move head vertically (TILT).
Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
The head can be turned by 270° and stopped at any position you wish.
Channel 3 – Colourwheel
Linear color change following the movement of the slider. Between 128 - 255, the color-wheel rotates
continuously the so-called “Rainbow” effect.
0-6
Open / White
7-13
Yellow
14-20
Pink
21-27
Green
28-34
Red
35-41
Light Blue
42-48
Light Green
49-55
Orange
56-64
Dark Blue
65-71
Split Color White / Yellow
72-78
Split Color Yellow / Pink
79-85
Split Color Pink / Green
86-92
Split Color Green / Red
93-99
Split Color Red / Light Blue
100-106
Split Color Light Blue / Light Green
107-113
Split Color Light Green / Orange
114-120
Split Color Orange / Dark Blue
121-127
Split Color Dark Blue / White
128-191
Clockwise rotation (CW) rainbow effect from slow to fast
192-255
Counter-clockwise rotation (CCW) rainbow effect from slow to fast
Channel 4 – Shutter / Strobe (Dimmer must be open )
0-3
Close
4-7
Shutter open
8-215
Strobe effect, from slow to fast (0-10 flashes/sec.)
216-255
Shutter open
Channel 5 – Dimmer intensity
0-255
From black to brightest
Channel 6 – Rotating Gobo-wheel + Gobo Shake
0-7
Open / White
8-15
Gobo 1 (Glass)
16-23
Gobo 2 (Glass)
24-31
Gobo 3 (Metal)
32-39
Gobo 4 (Metal)
40-47
Gobo 5 (Metal)
48-55
Gobo 6 (Metal)
56-63
Gobo 7 (Metal)
64-71
Gobo Shake 7 from slow to fast
74-79
Gobo Shake 6 from slow to fast
80-87
Gobo Shake 5 from slow to fast
88-95
Gobo Shake 4 from slow to fast
96-103
Gobo Shake 3 from slow to fast
104-111
Gobo Shake 2 from slow to fast
112-119
Gobo Shake 1 from slow to fast
120-127
Open / White
19
128-191
Clockwise rotation (CW) rainbow effect from slow to fast
192-255
Counter-clockwise rotation (CCW) rainbow effect from slow to fast
Channel 7 – Gobo rotation
0-7
No Rotation
8-119
Clockwise rotation (CW) from slow to fast
120-231
Counter-clockwise rotation (CCW) from slow to fast
232-255
Gobo bouncing
Channel 8 – Prism
0-15
Open
16-255
3-facet Prism Effect
Channel settings
Fig. 6
Maintenance
The operator has to make sure that safety-relating and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
1. All screws used for installing the device or parts of the device have to be tightly connected and must
not be corroded.
2. There may not be any deformations on housings, fixations and installation spots.
3. Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
4. The electric power supply cables must not show any damages or material fatigue.
The IMG Stage Line TWIST-5LED Spot requires almost no maintenance. However, you should keep the unit
clean. Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power
supply, and then wipe the cover with a damp cloth. Do not immerse in liquid. Wipe lens clean with glass
cleaner and a soft cloth. Do not use alcohol or solvents. The front lens will require weekly cleaning, as
smoke-fluid tends to build up residues, reducing the light-output very quickly.
The cooling-fans, colour-wheel, the gobowheel, the gobos and the internal lenses should be cleaned
monthly with a soft brush.
Please clean internal components once a year with a light brush and vacuum cleaner.
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections
with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying
electric power.
20
Replacing a Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out. If the
fuse burns out, the product will not function whatsoever. If this happens, follow the directions below to do
so.
1. Unplug the unit from electric power source.
2. Insert a flat-head screwdriver into a slot in the fuse cover. Turn the screwdriver to the left, at the same
time gently push a bit (Turn and Push). The fuse will come out.
3. Remove the used fuse. If brown or unclear, it is burned out.
4. Insert the replacement fuse into the holder where the old fuse was. Reinsert the fuse cover. Be sure to
use a fuse of the same type and specification. See the product specification label for details.
Rotating Gobo-wheel Colorwheel
1
8 2
7 3
6 4
5
Fig. 7 Fig. 8
Troubleshooting
No Light, No Movement - All Products
This troubleshooting guide is meant to help solve simple problems. If a problem occurs, carry out the steps
below in sequence until a solution is found. Once the unit operates properly, do not carry out following
steps.
If the light effect does not operate properly, refer servicing to a technician.
Response: Suspect three potential problem areas: the power supply, the lamp, the fuse.
1. Power supply. Check that the unit is plugged into an appropriate power supply.
2. The LEDs. Return the TWIST-5LED Spot to your IMG Stage Line dealer.
3. The fuse. Replace the fuse. See page 22 for replacing the fuse.
No Response to DMX
Response: Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card
malfunction.
1. Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
2. Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products ? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.
21
Problem
Probable cause(s)
Remedy
One or more
fixtures are
completely dead.
No power to the fixture
· Check that power is switched on
and cables are plugged in.
Primary fuse blown.
· Replace fuse.
Fixtures reset
correctly, but all
respond
erratically or not
at all to the
controller.
The controller is not connected.
· Connect controller.
3-pin XLR Out of the controller
does not match XLR Out of the first
fixture on the link (i.e. signal is
reversed).
· Install a phase reversing cable
between the controller and the first
fixture on the link.
Fixtures reset
correctly, but
some respond
erratically or not
at all to the
controller.
Poor data quality
· Check data quality. If much lower
than 100 percent, the problem may
be a bad data link connection, poor
quality or broken cables, missing
termination plug, or a defective
fixture disturbing the link.
Bad data link connection
· Inspect connections and cables.
Correct poor connections. Repair or
replace damaged cables.
Data link not terminated with 120
Ohm termination plug.
· Insert termination plug in output jack
of the last fixture on the link.
Incorrect addressing of the fixtures.
· Check address setting.
One of the fixtures is defective and
disturbs data transmission on the
link.
· Bypass one fixture at a time until
normal operation is regained: unplug
both connectors and connect them
directly together.
· Have the defective fixture serviced
by a qualified technician.
3-pin XLR Out on the fixtures does
not match (pins 2 and 3 reversed).
· Install a phase-reversing cable
between the fixtures or swap pin 2
and 3 in the fixture, that behaves
erratically.
Shutter closes
suddenly
The color wheel, gobo wheel, or a
gobo has lost its index position and
the fixture is resetting the effect.
· Contact a technician for servicing if
the problem persists.
No light
The power supply settings do not
match local AC voltage and
frequency.
· Disconnect fixture. Check settings
and correct if necessary.
LEDs damaged
· Disconnect fixture and return to your
dealer.
Lamp cuts out
intermittently.
Fixture is too hot.
· Allow fixture to cool.
· Clean fan.
· Make sure air vents at control panel
and front lens are not blocked.
· Turn up the air conditioning.
The power supply settings do not
match local AC voltage and
frequency.
· Disconnect fixture. Check settings
and correct if necessary.
22
Product Specification
Model: IMG Stage Line TWIST-5LED Spot
Input Voltage: 100-240 VAC
Peak Power 227 Watt; Continuous Power 185 Watt
Fuse: F2A / 250V
Dimensions: 210x225x340mm (LxWxH)
Weight: 5,64 kg
Operation and Programming
Signal pin OUT: pin 1 earth, pin 2 (-), pin 3 (+)
Set Up and Addressing: LED control panel
Pan/Tilt resolution: 8-16 bit
DMX Channels: 13 or 8
Signal input 3-pin XLR male
Signal output 3 -pin XLR female
13mm
Electro-mechanical effects
DMX-control via standard DMX-controller
Built-in Automatic Programs + Built-in Sound activated programs
User-selectable Pan & Tilt ranges, 540° / 360° / 180°
Reverse Pan / Tilt movement
Special: Pan / Tilt movement blackout
Pan 0º -- 540º
Tilt 0º -- 270º
Pan/Tilt resolution: 16 bit
16 Built in programs selectable by DMX
Rotation: Bi-directional
Prism: 3-facet prism
Light Source: 1 x 50W White LED
Colourwheel with 8 dichroic-colours and white
Gobo functions: Gobo-flow effect, Gobo shake
Color functions: Split colors, Rainbow-flow effect
Control: DMX-512, Master/Slave, Sound-controlled
Rotating Gobowheel with 2 glass gobos, 5 metal gobos and open with Gobo Shake Function
8 automatic and 8 sound-to-light programs with master / slave function
Single clamp bracket, which makes it easy to handle and position in truss systems.
Output: 18.500 Lux @ 1m.
Beam Angle: 17°
Dimmer: 0-100%
Strobe: 0-20Hz
Focus: Manual focus
Housing: Black Metal & Flame-retardant plastic
Fixture Connection: XLR Data in/out (XLR 3-pin), IEC Power in
User selectable Basic (8CH) or Advanced (13CH) operating modes
Gobos
Colourwheel: heat-resistant and intensify glass; dichroic glas coating
Max. ambient temperature t
a
: 40°C; Max. housing temperature tB: 80°C
Cooling: 2 axial fans – 1 fan in the projector and 1 in the base
Motor: high quality stepping-motor controlled by microprocessors
Minimum distance:
Minimum distance from flammable surfaces: 0.5m
Minimum distance to lighted object: 1.3m
Design and product specifications are subject to change without prior notice.
®
MONACOR INTERNATIONAL GmbH & Co. KG •Zum Falsch 36 •28307 Bremen •Germany
Copyright
©
by MONACOR INTERNATIONAL. All rights reserved. A-0000.99.01.12.2011
Loading...