IKA RO 10, RO 15, RO 5, RT 5, RT 10 User Manual

20000004954

RO/RT_072017

IKA® RT 5/10/15

IKA® RO 5/10/15

Contents

Page

Control panel and display 02
Contents 09
Declaration of conformity 09
Warranty 09
Explication of warning symbols 09
Safety instructions 10
Unpacking 11
Correct use 11
Commissioning 11
Safe temperature limit 11

Setting the safe temperature limit 11
Stirring function 11
Eco mode 12
Operating modes 12
Direction of rotation reversal 12
Function heating 12
Maintenance and cleaning 12
Error codes (RT 5/10/15) 13
Accessories 13
Technical data 14

EN

Declaration of conformity

We declare under our sole responsibility that this product is in compliance with the regulations 2014/35/EU, 2014/30/EU and 2011/65/
EU and conforms to the standards or normative documents: EN 61010-1, EN 61010-2-010, EN 61010-2-051, EN 61326-1, EN 60529
and EN ISO 12100.

Warranty

In accordance with IKA® warranty conditions, the warranty period is 24 months. For claims under the warranty please contact your
local dealer. You may also send the machine direct to our factory, enclosing the delivery invoice and giving reasons for the claim. You
will be liable for freight costs.
The warranty does not cover worn out parts, nor does it apply to faults resulting from improper use, insucient care or maintenance
not carried out in accordance with the instructions in this operating manual.

Explication of warning symbols

General hazard.

DANGER

WARNING

CAUTION

This symbol identifies informaton that is of absolute importance to ensure health and safety. Failure
to observe this information may be detrimental to health or may result in injuries.

This symbol indicates information witch is important for ensuring that the appliance functions
without any technical problems.
Failure to observe this information could damage the appliance.

This symbol indicates information which is important for proper use of the appliance and / or

ensuring that the appliance functions correctly.

Failure to observe this information can lead to inaccurate results.

ATTENTION

DANGER

ATTENTION - Risk of damage due to magnetism.

DANGER - Reference to the endangerment by a hot surface

9

Safety instructions

For your protection

• Read the operating instructions in full before starting

up and follow the safety instructions.

• Keep the operating instructions in a place where they can be
accessed by everyone.

• Ensure that only trained staff work with the appliance.

• Follow the safety instructions, guidlines, occupational health
and safety and and accident prevention regulations.

• Socket must be earthed (protective ground contact).
Attention - Magnetism!

ATTENTION

Effects of the magneticfield have to be
into account (e.g. data storage media,
cardiac pacemakers ...).
RT

DANGER

Risk of burns!
Exercise caution when touching the

housing parts and the heating plate.
The heating plate can reach temperatures in excess of 125 °C.
Pay attention to the residual heat after switching off.
RT

WARNING

Ensure that the mains power supply
cable does not touch the heating base
plate.

• Wear your personal protective equipment in accordance with
the hazard category of the media to be processed. Otherwise
there is a risk from:

- splashing and evaporati on of liquids

- ejection of parts

- release of toxic or combustable gases.

• Set up the appliance in a spacious area on an even, stable,
clean, non-slip, dry and fireproof surface.

• The feet of the appliance must be clean and undamaged.

• Check the appliance and accessories beforehand for damage
each time you use them. Do not use damaged components.

• Gradually increase the speed.

• Reduce the speed if

- the medium splashes out of the vessel because the speed is
too high

- the appliance is not running smoothly

- the container moves on the base plate.

RT

WARNING

Caution! Only process and heat up any
media that has a flash point higher than
180 °C.
The safe temperatue limit must always be set to at least 25 °C
lower than the fire point of the media used.
Beware of hazards due to:

WARNING

- flammable materials

- combustibles media with a low boiling temperature

- glass breakage

- inkorrect container size

- overfilling of media

- unsafe condition of container.

• The appliance may heat up when in use.

• The base plate can heat up due to the action of the drive mag­ nets at high motor speeds, even if the heater is not operational.

• Process pathogenic materials only in closed vessels under a
suitable extractor hood. Please contact IKA
questions.
Do not operate the appliance in explo-

DANGER

sive atmospheres, with hazardous
substances or under water.
Only process media that will not react

DANGER

dangerously to the extra energy produ­ ced through processing. This also ap­ plies to any extra energy produced in other ways, e.g. through
light irridiation.

• Please observe the operating instructions for any accessories
used.

• Safe operation is only guaranteed with the accessories descri­ bed in the „Accessories“ chapter.

• Accessories must be securely attached to the device and cannot
com off by themselves. The centre of gravity of the assembly
must lie within the surface on which it is set up.

• Always disconnect the plug before fitting accessories.

• The appliance can only be disconnected from the mains supply
by pulling out the mains plug or the connector plug.

• The socket for the mains cord must be easily accessible.

• It may be possible for wear debris from rotating accessory parts
to reach the material being processed.

• When using PTFE-coated magnetic bars, the following has to
be noted:
Chemical reactions of PTFE occur in contact with molten or

solute alkali metals and alkaline earth metals, as well as with
fine powders of metals in groups 2 and 3 of the periodic sys­ tem at temperatures above 300 °C - 400 °C. Only elementary
fluorine, chlorotrifluoride and alkalimetals attack it; halogena­ ted hydrocarbons have a reversible swelling effect.

For protection of the equipment

• The appliance may only be opened by experts.

• The voltage stated on the type plate must correspond to the
mains voltage.

• Do not cover the device, even partially e.g. with metallic plates
or film. This results in overheating.

• Protect the appliance and accessories from bumps and impacts.

• Ensure that the base plate is kept clean.

• Observe the minimum distances between the devices, between
device and wall and minimum distances (min. 800 mm) above
the assembly, see Fig. 2.

(Source: Römpps Chemie-Lexikon and „Ullmann“ Volume 19)

>100 mm

>100 mm

>100 mm

®

if you have any

Fig. 2

10