Iiyama TE5564MIS-B2AG User Manual

USER MANUAL

Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.

ENGLISH

CE MARKING DECLARATION OF CONFORMITY

This LCD monitor complies with the requirements of the EC/EU Directive 2004/108/EC “EMC Directive”, 2006/95/EC “Low Voltage Directive” and 2011/65/EU “RoHS Directive”.

Warning

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands

ENGLISH

We recommend recycling of used product. Please contact your dealer or iiyama service center. Recycle information is obtained via the Internet, using the address: http://www.iiyama.com You can access the Web page of different countries from there.

We reserve the right to change speciﬁ cations without notice.



All trademarks used in this user manual are the property of their respective owners.



TABLE OF CONTENTS

FOR YOUR SAFETY ............................................................................1

SAFETY PRECAUTIONS................................................................1

SPECIAL NOTES ON LCD MONITORS .........................................3

CUSTOMER SERVICE ...................................................................4

CLEANING ......................................................................................4

BEFORE YOU OPERATE THE MONITOR ..........................................5

FEATURES......................................................................................5

CHECKING THE CONTENTS OF THE PACKAGE ........................5

UNPACKING ...................................................................................6

SPECIAL NOTES ON : ProLite TE5564MIS / ProLite TH5564MIS

CONTROLS AND CONNECTORS : MONITOR ..............................7

INSTALLATION .............................................................................10

CONTROLS AND CONNECTORS : REMOTE CONTROL ...........12

PREPARING THE REMOTE CONTROL.......................................13

BASIC OPERATION ......................................................................14

CONNECTING YOUR MONITOR .................................................17

COMPUTER SETTING .................................................................19

OPERATING THE MONITOR .............................................................21

ADJUSTMENT MENU CONTENTS ..............................................23

SCREEN ADJUSTMENTS ............................................................31

POWER MANAGEMENT FEATURE .............................................34

TROUBLE SHOOTING ......................................................................35

RECYCLING INFORMATION .............................................................36

APPENDIX ........................................................................................37

SPECIFICATIONS : ProLite TE5564MIS-B1AG ............................37

SPECIFICATIONS : ProLite TE5564MIS-B2AG ............................38

SPECIFICATIONS : ProLite TH5564MIS-B2AG ...........................39

SPECIFICATIONS : ProLite LE5564S ..........................................40

DIMENSIONS : ProLite TE5564MIS-B1AG ..................................41

DIMENSIONS : ProLite TE5564MIS-B2AG ..................................41

DIMENSIONS : ProLite TH5564MIS-B1AG ..................................42

DIMENSIONS : ProLite LE5564S .................................................42

COMPLIANT TIMING ....................................................................43

PAP SUPPORT SCREEN TABLE .................................................44

..6

ENGLISH

FOR YOUR SAFETY

SAFETY PRECAUTIONS

WARNING

STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE

If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause ﬁ re or electric shock.

NEVER REMOVE THE CABINET

High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of ﬁ re or electric shock.

DO NOT PUT ANY OBJECT INTO THE MONITOR

Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug your monitor immediately and contact your dealer or iiyama service center. Using the monitor with any object inside may cause ﬁ re, electric shock or damage.

INSTALL THE MONITOR ON A FLAT, STABLE SURFACE

The monitor may cause an injury if it falls or is dropped.

DO NOT USE THE MONITOR NEAR WATER

Do not use where water may be splashed or spilt onto the monitor as it may cause ﬁ re or electric shock.

OPERATE UNDER THE SPECIFIED POWER SUPPLY

Be sure to operate the monitor only with the speciﬁ ed power supply. Use of an incorrect voltage will cause malfunction and may cause ﬁ re or electric shock.

ENGLISH

PROTECT THE CABLES

Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy objects on the cables. If damaged, the cables may cause ﬁ re or electric shock.

ADVERSE WEATHER CONDITIONS

It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in power may cause malfunction. It is also advised not to touch the plug in these circumstances as it may cause electric shock.

FOR YOUR SAFETY 1

CAUTION

INSTALLATION LOCATION

Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause ﬁ re, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor.

DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION

The monitor may topple and cause injury if not suitably located. Please also ensure that you do not place any heavy objects on the monitor, and that all cables are routed such that children may not pull the cables and possibly cause injury.

MAINTAIN GOOD VENTILATION

Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause

ENGLISH

ﬁ re. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls. Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the cabinet will be blocked and the monitor may overheat if the stand is removed. This may cause ﬁ re or damage. Operating the monitor on its back, side, upside down or on a carpet or any other soft material may also cause damage.

DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR

When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal cable is disconnected. If you do not disconnect them, it may cause ﬁ re or electric shock.

UNPLUG THE MONITOR

If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid accidents.

HOLD THE PLUG WHEN DISCONNECTING

To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself as this may cause ﬁ re or electric shock.

DO NOT TOUCH THE PLUG WITH WET HANDS

Pulling or inserting the plug with wet hands may cause electric shock.

WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER

Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage your computer.

REMARK FOR 24/7 USAGE

This product is not speciﬁ cally designed for 24/7 usage. (Recommended operating time is 12 hours/ Day.)

OTHERS

ERGONOMIC RECOMMENDATIONS

To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room. For optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches) away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour is recommended as looking at the screen continuously can cause eye strain.

2 FOR YOUR SAFETY

SPECIAL NOTES ON LCD MONITORS

The following symptoms are normal with LCD monitors and do not indicate a problem.

NOTE

When you ﬁ rst turn on the LCD monitor, the picture may not ﬁ t in the display area



because of the type of computer that is used. In this case, adjust the picture position to the correct position. You may ﬁ nd slightly uneven brightness on the screen depending on the desktop



pattern you use. Due to the nature of the LCD screen, an afterimage of the previous screen may



remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours. Max. non-stop operating time and conditions



(1) If a static image is displayed continuously, it is recommended to disrupt it with a

motion picture.

(2) It is recommended to periodically change the background colour and background

image.

ProLite LE5564S / ProLite TE5564MIS-B1AG / ProLite TE5564MIS-B2AG :

(3)

Recommended operating time is 12 hours/Day.

ProLite TH5564MIS-B2AG :

Maximum operating time of the display is 18 hours per day, if the Image Retention is set on. If the Image Retention is off, do not exceed a 12 hour non-

stop operating time limit. (4) If the screen is active for a longer period of time, it is recommended to I. Run the screensaver (motion picture or black pattern) II. Power off the system for a while (5) Make sure that the screen is suitably ventilated, or is used in conjunction with

climate control system if installed into any bespoke cabinets. (6) We strongly recommend an active cooling system with fans for long operating times,

especially for high luminance LCD models. This LCD cannot be used outdoors.



This LCD cannot be used with the screen facing upwards.



If you use a cable longer than the supplied one, the picture quality is not guaranteed.



Touch function can be disrupted if the USB cable length exceeds 3m.

ENGLISH

FOR YOUR SAFETY 3

CUSTOMER SERVICE

NOTE

CLEANING

WARNING

ENGLISH

CAUTION

NOTE

CABINET

LCD SCREEN

If you have to return your unit for service and the original packaging has been



discarded, please contact your dealer or iiyama service center for advice or replacement packaging.

If you drop any materials or liquids such as water into the monitor when cleaning,



unplug the power cable immediately and contact your dealer or iiyama service center. For safety reasons, turn off the power switch and unplug the monitor before you



clean it. To protect the LCD panel, do not scratch or rub the screen with a hard object.



Never use any of the following strong solvents. These will damage the cabinet and



the LCD screen.

Thinner Benzine Abrasive cleaner

Spray-type cleaner Wax Acid or Alkaline solvent

Touching the cabinet with any product made from rubber or plastic for a long time



may cause degeneration or loss of paint on the cabinet.

Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then wipe the cabinet with a soft dry cloth.

Periodic cleaning with a soft dry cloth is recommended. Don't use tissue paper etc. because these will damage the LCD screen.

4 FOR YOUR SAFETY

BEFORE YOU OPERATE THE MONITOR

FEATURES

Supports Resolutions up to 1920 × 1080



High Contrast 1400:1 (Typical: without Touch panel) / Brightness 350cd/m2



(Typical: without Touch panel): ProLite TE5564MIS-B1AG / ProLite TE5564MISB2AG / LE5564S

High Contrast 4000:1 (Typical: without Touch panel) / Brightness 450cd/m



(Typical: without Touch panel): ProLite TH5564MIS-B2AG

Digital Character Smoothing



Automatic Set-up



Stereo Speakers



2 × 12W Stereo Speakers

Plug & Play VESA DDC2B Compliant



Windows

Power Management (VESA DPMS Compliant)



VESA Mounting Standard (400mm×400mm) Compliant



95/98/2000/Me/XP/Vista/7/8 Compliant

ENGLISH

CHECKING THE CONTENTS OF THE PACKAGE

The following accessories are included in your package. Check to see if they are enclosed with the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama ofﬁ ce.

Power Cable*



USB Cable*2



iiyama Logo Sticker



Quick Start Guide



CAUTION



The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using a power supply higher than this rating, then a power cable with a rating of 10A/ 250V must be used. However, all guarantees and warranties are void for any problems or damage caused by a power cable not supplied by iiyama.

*2 Accessory for ProLite TE5564MIS / ProLite TH5564MIS.

VGA(D-sub) Signal Cable  DVI-D Signal Cable Remote Control



Logo Guider



Touch Pen*2



Safety Guide



BEFORE YOU OPERATE THE MONITOR 5

UNPACKING

Before unpacking your monitor, prepare a stable, level, and clean surface near a wall outlet.

Set the LCD Monitor box in an upright position and open from the top of the box before removing

the top cushions. Remove the carton holders. Remove the top cushion and take

the accessories box and the Monitor out.

Pinch and Pull the Knob.

CAUTION

ENGLISH

Moving the monitor requires at least two people. If not, it may drop and could result in a serious injury. When moving/shipping the monitor, please hold by the carton holders.

SPECIAL NOTES ON : ProLite TE5564MIS / ProLite TH5564MIS

CAUTION

Permanent damage can occur if Sharp Edged, Pointed or Metal items are used to activate Touch. This could invalidate any remaining warranty. We recommend you use a plastic stylus (tip R0.8 or over) or ﬁ nger.

6 BEFORE YOU OPERATE THE MONITOR

CONTROLS AND CONNECTORS : MONITOR

VIDEO SOURCE

/ -

/ +

ProLite LE5564S-B1



ProLite TE5564MIS-B1AG

ENTER / VIDEO SOURCE Enter/Input Select Button MENU Menu Button

Up Button / - Left / - Button / + Right / + Button

Power Button

<Front>

ProLite TE5564MIS-B2AG



ProLite TH5564MIS-B2AG

Down Button

ENGLISH

Green Normal Operation

Flash : Power Management (Power Save : Low)

Power Indicator

Red

Lighting : If turn off the Power Button on the Remote Control and the Back Controller. Power Management (Power Save : High)

Off Power Off

Remote Sensor Remote Sensor

Detects ambient lighting conditions around the Monitor

Ambient Light Sensor

and adjusts screen brightness automatically when the Ambient Light Sensor function is activated.

BEFORE YOU OPERATE THE MONITOR 7

ProLite LE5564S-B1



ProLite TE5564MIS-B1AG

ENGLISH

ProLite TE5564MIS-B2AG



ProLite TH5564MIS-B2AG

<Back>

8 BEFORE YOU OPERATE THE MONITOR

RJ45 RJ45 RJ45 Connector RS232C OUT D-SUB 9pin RS232C IN D-SUB 9pin

RS232C Connector

RS232C Connector DisplayPort (DP) DisplayPort DisplayPort Connector DVI OUT DVI-D 24pin DVI-D 24pin Connector DVI IN DVI-D 24pin DVI-D 24pin Connector HDMI2 HDMI HDMI1 HDMI COMPONENT

VIDEO (VIDEO IN)

RCA G/B/R Component Video Connector

S-Video Mini Din 4pin

HDMI Connector

S-Video Connector AV OUT BNC Video Connector AV IN BNC Video Connector VGA OUT VGA(D-sub) mini 15pin VGA(D-sub) mini 15pin Connector VGA IN VGA(D-sub) mini 15pin VGA(D-sub) mini 15pin Connector AUDIO IN1 (PC Audio In) Mini Jack AUDIO IN2 RCA L/R AUDIO OUT RCA L/R

Audio Connector

Audio output Connector

SPEAKERS OUT Jack External Speakers Connector USB* USB Touch USB Connector AC SWITCH (ON) / (OFF) MAIN POWER Main Power Switch

AC IN AC-INLET AC OUT AC-OUTLET

AC Connector

( : Alternating current) (AC-IN)

AC Connector (AC-OUT)

SPEAKERS Speakers

* Available for ProLite TE5564MIS / ProLite TH5564MIS only.

ENGLISH

BEFORE YOU OPERATE THE MONITOR 9

INSTALLATION

CAUTION

Follow the manual instructions for the type of mount you have selected. Refer all servicing to



qualiﬁ ed service personnel.

Moving the monitor requires at least two people.



Before installing, please make sure the wall is strong enough to hold the necessary weight of the



display and the mount.

[WALL MOUNTING]

Mounting Stage

ENGLISH

CAUTION

When using the wall mounting, consideration of thickness of the mounting stage needs to be taken. Tighten the M8 Screw with washer which “L” length is 10mm to fasten the monitor. Using a screw longer than this may cause electric shock or damage because it may contact with the electrical parts inside the monitor.

Screw

Chassis

[INSTALLATION NOTE]

*Available for ProLite TE5564MIS / ProLite TH5564MIS only.

The touch kit of this monitor is an optical device that utilizes infrared light source and sensitive sensors for touch detection. Notice the incident light that contains large quantities of infrared light may affect touch screen operation and performance.

Please install it with care as follows to ensure reliable touch performance. Intense light / Specular light / Focus spotlight / Wide spread light / Direct sunlight / Indirect sunlight from the window and/or the glass door. / Not install the touch monitor right under the light source.

Light source

Front Front

Side

10 BEFORE YOU OPERATE THE MONITOR

Light source

Side

Windows

Direct

Sunlight

Light

source

[ROTATING THE DISPLAY]

It is designed to be compatible in landscape mode.

ProLite LE5564S-B1 / ProLite TE5564MIS-B1AG / ProLite TE5564MIS-B2AG



Available

Not Available

Landscape

Power indicator

ProLite TH5564MIS-B2AG



Available

Landscape

Power indicator

Portrait

ENGLISH

Power indicator

Not Available

Power indicator

BEFORE YOU OPERATE THE MONITOR 11

CONTROLS AND CONNECTORS : REMOTE CONTROL

ON/OFF Turns the monitor ON and OFF. INPUT Selects the source.

Serve as input source buttons when Number (1-9) / Input source

EXIT

ENGLISH

ENTER

INFO

Number (0)/ MUTE MULTI-MEDIA Not available on this model.

the Menu is not displayed.

The SDI and MULTI-MEDIA functions

are not available with this monitor.

Returns to a previous menu or closes

the OSD Menu.

Navigates through submenus and

settings.

volume.

Conﬁ rms your selection or save

changes.

Provides source and resolution

information.

Opens the monitor's on-screen menu

systems. When the menu system is

already open, pressing this button will

select the previous submenu.

Turns on or off the mute function

when the Menu is not displayed.

: Up Button

: Down Button : Left Button : Right Button (VOLUME-): Decreases the sound

(VOLUME+): Increases the sound

12 BEFORE YOU OPERATE THE MONITOR

+ 32 hidden pages