iHome iB75 User Manual

Model: iB75
Bluetooth wireless earbuds with mic + remote and pouch
Introduction
Your new iHome Bluetooth stereo headphones are designed to link with your Bluetooth enabled smartphone or music player to allow you to wirelessly listen to music and answer phone calls within the normal 10 meter (30 feet) Bluetooth operating range.
What’s Included
USB Cable
x 2
L
SIZE
x 1set
L
iB75 Bluetooth
Wireless Headphones
Specications
Bluetooth specication: Supports V2.1 + EDR with Handsfree Prole 1.5,
Standby time: 100 hours (with fully charged battery)
Talk time: 8 hours (with fully charged battery)
Music Playing Time: 7 hours (with fully charged battery)
Operating Distance: up to 10 meters / 30 feet
Weight: 16 grams
Certications: CE, FCC, RoHS, BQB
Headset Prole 1.1 and A2DP prole 1.2 (Class ll)
SIZE
M
x 2
SIZE
Silicon Tips
M
x 1set
SIZE
Stabilizer Fins
S
SIZE
S
SIZE
x 2
x 1set
Controls and Indicators
2
1
3
2
4
5
+
-
7 8
6
9
1. Multi-function button: Power On/Off, Answer/End, Pair, Play, and Pause
2. Speakers
3. Back button
4. Forward button
5. Mini 8-pin USB Charging Port (located under water resistant cover)
6. Microphone
7. Volume + button
8. Volume - button
9. Power On, Charging, Pairing LED Indicator
Charging Your Headphones
IMPORTANT: Your headphones operates on a built-in rechargeable lithium-ion battery. You should charge the battery for a full 4 hours before rst time use.
1. Lift up the water resistant cover to expose the Mini 8-pin USB charging port.
2. Connect the Mini 8-pin USB plug on the charging cable to the Mini 8-pin USB port on the headphones.
3. Connect the standard USB plug on the charging cable to any standard USB power port such as found on a notebook computer, or the charging adapter for an iPod, iPhone, etc.
4. The Power/Charging/Pairing indicator will glow RED while the headphones is charging. The indicator will turn Off when the battery is fully charged.
Reminder: Allow the battery to charge for 4 hours before rst time use. Normal recharge time after rst use should take about 2 hours. When full charged the battery will provide up to 8 hours of talk time, 7 hours of music playing time, or 100 hours of standby time.
Switching the Power On and Off
1. Press and hold the Multi-function button for approximately 3 seconds until a ‘beep’ is heard. The LED indicator turns blue and begins ashing slowly. This indicates that the power is ‘On’.
2. When the power is ‘On’ press and hold the Multi-function button for approximately 3 seconds until a ‘beep’ is heard. The LED indicator turns red, ashes for a few seconds and then shuts off. This indicates that the power is ‘Off’.
Pairing With a Bluetooth Enabled Smartphone or Music Player
If your smartphone or music player, such as the iPod touch, is Bluetooth enabled (supports the A2DP Bluetooth Prole) you may pair these iHome headphones with your phone or music player to listen to music and make or receive calls as long as the two devices are within the Bluetooth operating range of approximately 30 feet of each other.
1. Make sure that your iHome iB75 headphones are in the Power Off mode. Make sure that your smartphone or music player is ‘On’.
2. Press and hold the Multi-function button on your iB75 headphones for about 5 seconds until the LED indicator alternately ashes red and blue to indicate it is trying to pair with a compatible device.
3. If necessary, turn on the Bluetooth function of your phone or music player so that it begins searching for a compatible device.
4. “iHome iB75” should appear on your phone or music player’s compatible devices list. You may also see a message such as “Not Paired”. Tap on that message to complete the pairing process. If your phone or music player asks for a ‘password’ to complete the pairing process, enter ‘0000’ on the keypad of your phone or music player.
5. When pairing is successful the screen on your phone should show “iHome iB75 Connected” or similar message and the blue LED indicator on the iB75 headphones should ash repeatedly. Your headphones are now ready for use.
Wearing Your Headphones
Your iHome Bluetooth headphones are supplied with 3 different sizes of silicon ear cushions (tips) and three different sizes of soft rubber stabilizer ‘ns’ designed to prevent the headphones from falling out of your ears during periods of strenuous physical activity. Refer to the following illustration showing the proper way to t the headphones in your ears with the stabilizer ns installed.
Although you must use the headphones with the silicon cushions to form a proper seal in your ear canals, using the stabilizer ns is optional.
The medium (M) size cushions and ‘ns’ were installed at our factory. If you nd that the M size cushions and ns are either too big or too small for you, you may change to the S or L size cushions and ns. Start by removing the cushions simply by pulling them off the plastic tubes. Then remove the rubber ‘ns’ from the speaker housing. Install either the S of L fins on the speaker housings first, then install either the S or L cushions by pushing them onto the plastic posts as far as they will go. Make sure that the cushions are securely xed on the posts so that a cushion does not remain in your ear when you remove the headphones.
Loading...
+ 5 hidden pages