IC Realtime NVR 6000 Quick Start Manual

NVR 6000 Series Quick Start Guide

V2.0.0

i

Table of Contents

1 INSTALLATION AND CONNECTIONS ....................................................1

1.1 Check Unpacked NVR............................................................................................................1

1.2 Front Panel...............................................................................................................................1

1.3 Rear Panel................................................................................................................................2

1.4 Alarm Input and Output Connection .....................................................................................2

1.4.1 Alarm Input and Output Details.........................................................................................3

1.4.2 Alarm Input Port ..................................................................................................................3

1.4.3 Alarm Output Port...............................................................................................................4

2 OVERVIEW OF NAVIGATION AND CONTROLS ....................................5

2.1 Search & Playback ..................................................................................................................8

2.2 Network...................................................................................................................................12

2.2.1 Network Setting.................................................................................................................12

2.3 Remote Device ......................................................................................................................13

2.4 Manual Record.......................................................................................................................14

2.4.1 Manual record menu ........................................................................................................14

2.4.2 Basic operation .................................................................................................................14

2.4.3 Enable/disable record ......................................................................................................14

2.4.4 Enable all channel recording...........................................................................................14

2.4.5 Stop all channel recording...............................................................................................15

2.5 Shutdown................................................................................................................................16

ii

3 SYSTEM UPGRADE .............................................................................. 17

4 WEB OPERATION .................................................................................18

4.1 General Introduction..............................................................................................................18

4.1.1 Preparation ........................................................................................................................18

4.2 Login........................................................................................................................................18

APPENDIX H TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS........21

iii

Welcome

Thank you for purchasing our NVR!

This quick start guide is designed to be a reference tool for the installation and operation

of your system.

Before installation and operation please read the following safeguards and warnings

carefully!

Please keep it for future reference!

iv

Important Safeguards and Warnings

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.

We assume no liability or responsibility for all the fires or electrical shock caused by

improper handling or installation.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation,

storage and installation.

3．Installation

Keep upwards. Handle with care.

Do not apply power to the NVR before completing installation.

Do not place objects on the NVR.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted

repair.

5．Environment

The NVR should be installed in a cool, dry place away from direct sunlight, inflammable,

explosive substances and etc.

This series product shall be transported, storage and used in the specified environments.

6. Lithium battery

Improper battery use may result in fire, explosion, or personal injury!

When replace the battery, please make sure you are using the same model!

7. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Name Quantity

Front panel key 2

HDD screws 68

Quick start guide 1

CD 1

1

1 Installation and Connections

Note: All the installation and operations here should conform to your local electric safety

rules.

1.1 Check Unpacked NVR

When you receive the NVR from the forwarding agent, please check whether there is any

visible damage. The protective materials used for the package of the NVR can protect most

accidental clashes during transportation. Then you can open the box to check the accessories.

Please check the items in accordance with the list. Finally you can remove the protective film of

the NVR.

1.2 Front Panel

The front panel is shown as below. See Figure 1-1.

Figure 1-1

Please refer to the following sheet for front panel button information.

SN Name Function

1 Power button Press it once to turn on the device.

Press it for a long time to turn off the device. (Usually we do not

recommend).

2 System HDD

Indication light

The blue light flashes when system is reading or writing the system

HDD.

In the system HDD, there are device important configuration file,

factory default configuration file, and device initial boot up data.

3 Alarm indication

light

The alarm indication light becomes on once an alarm occurred. The

alarm includes hardware alarm, network abnormal events, or system

receives the alarm signal and etc.

4 Network

indication light

The network indication light is blue and it flashes when you connect

the device to the network.

5 USB port /

6 Front panel lock /

After you remove the front panel, you can see there are 16 HDDs. From the left to the right and

2

from the top to the bottom, it ranges from 1~4, 5~8, 6~12, 13~16.

You can see there are two indication lights on the HDD bracket.

z The power indication light is at the top. The light is yellow after you connected the device to

the power.

z The read-write indication light is at the bottom. The blue light flashes when system is

reading or writing the data.

1.3 Rear Panel

The rear panel is shown as below. See Figure 1-2.

Figure 1-2

Please refer to the following sheet for detailed information.

SN Function SN Function

1 Power socket 6 Video VGA output

2 Audio Input 7 eSATA port

3 Audio output 8 USB port

4 Bidirectional talk input 9 HDMI port

5 Network port 10 Alarm input, alarm output, RS485 port.

1.4 Alarm Input and Output Connection

Please refer to the following sheet for alarm input and output connection.

There are two alarm input types for you to select: normal open (NO) and normal close (NC).

1. Alarm input

a. Please make sure alarm input mode is grounding alarm input.

b. Grounding signal is needed for alarm input.

c. Alarm input needs the low level voltage signal.

d. Alarm input mode can be either NC (normal Open) or NO (Normal Close)

e. When you are connecting two NVRs or you are connecting one NVR and one other device,

please use a relay to separate them.

2. Alarm output

The alarm output port should not be connected to high power load directly (It shall be less than

1A) to avoid high current which may result in relay damage. Please use the co contactor to

3

realize the connection between the alarm output port and the load.

3. Please make sure the front-end device has soundly earthed.

Improper grounding may result in chip damage.

1.4.1 Alarm Input and Output Details

You can refer to the following sheet X for alarm input and output information. See Figure 1-3.

Figure 1-3

Please refer to the following sheet and Figure 1-3 for detailed information.

1，2，3，4，5，6，
7，8，9，10，11 ，
12，13，14，15，16

ALARM 1 to ALARM 16. The alarm becomes active in low voltage.

1-ON C，2- ON C，
3- ON C，4- ON C，
5- ON C，6- ON C，
7 - ON C，8- ON

Eight groups of normal open activation output (on/off button)

G GND cable.

485 A/B The A/B cable to control the RS485 devices. It is to connect to

control decoder such as the recorder.

Tx and Rx RS232 port. Tx is the data output cable and the Rx is the data input

cable.

1.4.2 Alarm Input Port

Please refer to the following sheet for more information.

z Grounding alarm inputs. Normal open or Normal close type)

z Please parallel connect COM end and GND end of the alarm detector (Provide external

power to the alarm detector).

z Please parallel connect the Ground of the NVR and the ground of the alarm detector.

z Please connect the NC port of the alarm sensor to the NVR alarm input(ALARM)

z Use the same ground with that of NVR if you use external power to the alarm device.