HD Panorama Network Camera
User’s Manual
Version 1.0.0
i
Welcome
Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series
product!
Please keep this user’s manual well for future reference!
ii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and
the Limited power source is rated 12V DC in the IEC60950-1. This series product
supports PoE too.
Note: Do not connect these two power supplying sources to the device at the same
time; it may result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
We are not liable for any problems caused by unauthorized modification or attempted
repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation,
storage and installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted
repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct
sunlight, inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam
device. Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding holes of the product are recommended to be grounded to further enhance
the reliability of the camera.
iii
Accessory Name
Amount
Network Camera
1
Quick Start Guide
1
Installation Accessories Bag
1
CD
1
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily
maintenance work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust
on the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use
the water to dilute the mild detergent first and then use it to clean the device. Finally use
the dry cloth to clean the device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use
the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are
installing the device or clean the enclosure when you are doing maintenance work.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
iv
Table of Contents
1 General Introduction ..................................................................................................... 1
1.1 Overview ........................................................................................................ 1
1.2 Features ......................................................................................................... 1
1.3 Specifications ................................................................................................. 2
1.3.1 Performance ........................................................................................... 2
1.3.2 Factory Default Setup ............................................................................. 4
2 Structure ..................................................................................................................... 10
2.1 Multi-function Combination Cable ................................................................ 10
2.2 Dimensions .................................................................................................. 10
2.3 Bidirectional Talk .......................................................................................... 11
2.3.1 Device-end to PC-end .......................................................................... 12
3 Installation................................................................................................................... 13
3.1 General Installation ...................................................................................... 13
3.2 Device Installation Steps ............................................................................. 13
3.3 Micro SD Card Installation ........................................................................... 14
3.4 Manual Zoom Lens Focus Operation .......................................................... 15
4 Quick Configuration Tool ............................................................................................ 16
4.1 Overview ...................................................................................................... 16
4.2 Operation ..................................................................................................... 16
5 Web Operation ........................................................................................................... 19
5.1 Network Connection..................................................................................... 19
5.2 Login and Main Interface ............................................................................. 19
5.3 Panorama Function on Web ........................................................................ 21
5.3.1 Installation Mode................................................................................... 21
5.3.2 Display Mode ........................................................................................ 22
6 FAQ ............................................................................................................................ 23
Appendix Toxic or Hazardous Materials or Elements ....................................................... 24
1
1 General Introduction
User
Management
Different user rights for each group, one user belongs to one group.
The user right shall not exceed the group right.
You can edit each group at anytime.
Storage
Function
Support central server backup function in accordance with your
configuration and setup in alarm or schedule setting
Support record via Web and the recorded file are storage in the client-end
PC.
Support built-in Micro-SD card.
Support network storage like FTP, support short-time storage when
encounter disconnection. (Only particular models have this function.)
Alarm
Function
Real-time respond to external local alarm input and video detect as user
pre-defined activation setup and exert corresponding message in screen
and audio prompt(allow user to pre-record audio file)
Real-time video detect: motion detect, camera masking.
Can generate an alarm when network abnormal, Micro-SD card abnormal
event occurred.
Network
Monitor
Network camera supports one-channel audio/video data transmit to
network terminal and then decode. Delay is within 270ms (network
bandwidth support needed)
Max supports 20 connections.
Adopt the following audio and video transmission protocol: HTTP, TCP,
UDP, RTP/RTCP, RTSP and etc.
Support web access, widely used in WAN.
1.1 Overview
This series network camera combines traditional camera and network video technology
into one unit which integrates A/V data collection and transmission through network
without aux devices. It uses standard H.264 and MJPEG video compression technology,
which maximally guarantee the audio and video quality.
This series network camera enclosure has the strong resistance capacity, which can
guarantee the proper work performance under heavy strike. It supports real-time monitor
and listening at the same time.
It can be used alone or used in a network area. When it is used lonely, you can connect it
to the network and then use a network client-end. Due to its multiple functions and various
uses, this series network camera is widely used in many environments such home, office,
bank, road monitor and etc.
1.2 Features
2
Network
Management
Realize network camera configuration and management via Ethernet.
Support device management via web or client-end.
Support various network protocols.
Power
External power adapter DC12V
PoE
Warning！
Do not connect two power supplying sources to the device at the
same time; it may result in device damage!
Assistant
Function
Log function
Support PAL/NTSC
Support display of system source info and working status
Day/Night mode auto switch
Backlight compensation: screen auto split to realize backlight
compensation to adjust the bright.
Support electronic shutter and gain setup.
Support video watermark function to avoid vicious video modification.
Support language function.
Model
Parameter
ICIP D2360
System
Main
Processor
TI Davinci high performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network monitoring, local record, and remote
operation at the same time.
User
Interface
Remote operation interface such as WEB, DSS, PSS
System
Status
Micro-SD card status, bit stream statistics, log, and software version.
Video Parameter
Image
Sensor
1/2.9 inch CMOS
Pixel
1920(H)*1080(V)
Day/Night
Mode
Support day/night mode switch
Gain Control
Fix/Auto
White
Balance
Manual/Auto
BLC
On/Off
Electronic
Shutter
Manual/Auto
It ranges from 1/3 to 1/10000.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for network camera performance specification.
3
Video
Compressio
n Standard
H.264/H.264B/MJPEG
Video Frame
Rate
PAL:
Main stream
(1080P@25fps,SXGA@25fps,1.3M@25fps,720P@25fps,D1@25fps)
Extra stream (D1@25fps,CIF@25fps)
NTSC:
Main stream
(1080P@30fps,SXGA@30fps,1.3M@30fps,720P@30fps,D1@30fps)
Extra stream (D1@30fps,CIF@30fps)
Video Bit
Rate
H.264:56Kbps-8192Kbps. It is adjustable;
MJPEG: 40Kbps-20480Kbps. It is adjustable and bit rate is adjustable.
Support customized setup.
Video Flip
Support mirror.
Support flip function.
Snapshot
Max 1F/S JPEG snapshot
Privacy
Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, privacy mask.
Lens
1.25mm F1.8 D\H\V：180°±5°
Lens
Interface
M12 is the default accessories.
Video
Motion
Detect
396 (18 *22) detection zones；sensitivity level ranges from 1 to 6
(The 6th level has the highest sensitivity)
Activation event: video storage, image snapshot, log, email function
and etc.
Privacy
Mask
Activation event: video storage, image snapshot, log, email function
and etc.
Record and
Backup
Record
Priority
Manual>Video detect>Schedule
Local
Storage
Support Micro SD card storage
Network
Wired
Network
1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network
Protocol
HTTP,TCP/IP,IPv4/IPv6,ARP,IGMP ,ICMP,RTSP,RTP,UDP,SMTP,F
TP,DHCP,DNS,DDNS,PPPOE,UPNP,NTP,Bonjour,SNMP.
Platform
Interface
Standard
ONVIF
Remote
Monitor, system setup, log information, maintenance , upgrade and
4
Operation
etc
AUX
Interface
Reset
Built-in RESET button
General Parameter
Power
Support DC12V and PoE.
Power
Consumptio
n
2.5W MAX
Working
Temperatur
e
-10℃~+60℃
Working
Humidify
10%~90%
Dimensions(
mm)
¢110×54
Weight
0.25Kg
Installation
Mount on wall, ceiling and etc
Function
Setup Type
Item
Default setup
ICIP D2360
Camera Setup
Conditions
Brightness
50
Contrast
50
Saturation
50
Hue
50
Gain limit
0~50
Exposure mode
Auto
Scene mode
Auto
Day/night mode
Auto
BLC
Off
Mirror
Disable
Flip
Disable
Video
Video bit stream
Main
stream
Bit stream
type
General
Encode mode
H.264B
Resolution
1080P (1920*1080)
Frame
rate(FPS)
PAL: 25
NTSC: 30
1.3.2 Factory Default Setup
Please refer to the following sheet for factory default setup information.
5
Function
Setup Type
Item
Default setup
ICIP D2360
Bit stream
type
CBR
Reference bit
rate
3584-8192 Kb/S
Bit rate
8192
I frame interval
50
Watermark
settings
Enable
Watermark
character
DigitalCCTV
Extra
stream
Enable
Enable
Bit stream
type
General
Encode mode
H.264B
Resolution
CIF(352×288/352*240)
Frame
rate(FPS)
PAL: 25
NTSC: 30
Bit rate type
CBR
Reference bit
rate
192-1024Kb/S
Bit rate
1024
I frame
interval
50
Snapshot
Snap type
General snap
Image size
1080P (1920*1080)
Quality
Better
Speed
1s/picture
Overlay
Privacy mask
Disable
Channel title
Enable
Time title
Enable
Path
Snapshot path
C:\PictureDownload
Record path
C:\RecordDownload
Network
setup
TCP/IP
Host name
IPC
Ethernet card
Wired(Default)
6
Function
Setup Type
Item
Default setup
ICIP D2360
Mode
Static
MAC address
Depends on the device
IP version
IPV4
IP address
192.168.1.108
Subnet mask
255.255.255.0
Default
gateway
192.168.1.1
Preferred DNS
8.8.8.8
Alternate DNS
8.8.8.8
Enable
ARP/Ping to
set IP address
service
Enable
Connection
Max
connection
10
TCP port
37777
UDP port
37778
HTTP port
80
RTSP port
554
PPPoE
Enable
Disable
User name
N/A
Password
N/A
DDNS
Server type
Disable ， CN99
DDNS
Server IP
none
Port
80
Domain name
none
User name
none
Password
N/A
Update period
10m
IP filter
Trusted sites
Disable
SMTP(email)
SMTP server
none
Port
25
Anonymity
Disable
User name
anonymity
Password
N/A
Sender
none
Authentication
(Encrypt
mode)
N/A
Title (Subject)
IPC Message
7
Function
Setup Type
Item
Default setup
ICIP D2360
Main Receiver
N/A
Interval
0s
Health email
Disable ，
interval=60m
UPnP
Enable UPnP
Disable
SNMP
SNMP v1
Disable
SNMP v2
Disable
SNMP port
161
Read
community
public
Write
community
private
Trap address
N/A
Trap port
162
Bonjour
Enable
Enable
Server name
“Device name+SN”.
Depends on the
device.
Multicast
Multicast
address
239.255.42.42
Port
36666
QoS
Real-time
monitor
0
Command
0
Event
management
Video detect
Motion detect
Enable
Disable
Anti-dither
5 seconds
Sensitivity
3
Record
Channel
Enable
Record Delay
10 seconds
Send email
Disable
Snapshot
Disable
Video (Camera)
masking
Enable
Disable
Record
Channel
Enable
Record Delay
10 seconds
Send email
Disable
Snapshot
Disable
Abnormity
N
o
M
i
c
r
o
-
S
D
Enable
Disable
8
Function
Setup Type
Item
Default setup
ICIP D2360
Send email
Disable
Capacity
warning
Enable
Disable
Capacity limit
(Space
threshold)
10%
Send email
Disable
Micro-
SD
card
error
Enable
Disable
Send email
Disable
Disconn
ection
Enable
Disable
Record
Enable
Record delay
10s
IP
conflict
Enable
Disable
Record
Enable
Record delay
10s
Storage
management
Storage
FTP
FTP enable
Disable
Server IP
N/A
Port
21
User name
anonymity
Password
N/A
Remote
storage path
share
Emergency
storage to
local path
Disable
Record control
Pack duration
8m
Pre-record
5s
Disk full
Overwrite
Record mode
Auto
System
management
General setup
Local
setup
Device name
Depends on the device
Language
English
Video
standard
NTSC
Date and time
Date format
Y-M-D
Time format
24H
Time zone
GMT+08:00
Current time
Sync PC
DST
Disable
DST type
Week
Start time
00:00:00 of the first
Sunday of the month
9
Function
Setup Type
Item
Default setup
ICIP D2360
End time
00:00:00 of the second
Monday of the month
Synchronize
with NTP
Disable
NTP server
clock.isc.org
Port
37
Update period
10m
Auto maintenance
Auto reboot
Disable
Auto delete
old files
Disable
10
2 Structure
No.
Port
Port Name
Connector
Description
1
LAN
Network port
Ethernet
Connect to Ethernet cable.
2
DC12V
Power input
/
Power port, input 12V DC.
2.1 Multi-function Combination Cable
Figure 2- 1
The multi-function cable is in Figure 2- 1.
Please refer to the following sheet for corresponding information.
2.2 Dimensions
You can refer to the following figures for dimension information. The Unit is mm. See
Figure 2- 2, Figure 2- 3, and Figure 2- 4.
Figure 2- 2
11
Figure 2- 3
Figure 2- 4
2.3 Bidirectional Talk
12
2.3.1 Device-end to PC-end
Device Connection
Please connect the speaker to the audio input port of the PC.
Login the Web and then click the Talk button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the bidirectional talk function.
Click Talk button again to stop the bidirectional talk function.
Listening Operation
At the device end, speak via the speaker, and then you can get the audio at the pc-end.
13
3 Installation
Important
Before you complete the installation and setup, do not remove the electrostatic
attraction film on the transparent enclosure. Otherwise it may result in injury.
After remove electrostatic attraction film, do not touch dome enclosure in case
it may leave stain.
Before the installation, please make sure the installation surface can sustain at
least 3X weight of the bracket and the camera.
3.1 General Installation
Please refer to Figure 3- 1 for device installation information. You can see there are
installation screws in the accessories bag for you to install the device conveniently.
Figure 3- 1
3.2 Device Installation Steps
Step 1
Use the inner hex wrench from the accessories bag to unfasten the 3 hex screws on the
dome camera enclosure and then remove it.
Step 2
Take the installation position diagram from the accessories bag and then paste it on the
installation ceiling or the wall according to the monitor area. Please dig three bottom holes
of the plastic expansion bolts according to the diagram. Take three expansion bolts from
the accessories bag and then insert them to the holes you just dug and then fix firmly. If
14
you need to dig a hole to pull through the cable on top of installation surface, you need to
dig a cable exit hole on the installation surface according to the installation positioning
diagram. If you need to pull through the cable on the side, you need to dig through the
U-shape exit hole on the side of chassis.
Step 3
Adjust the device chassis and pull the cable through the exit hole. Make “TOP” direction of
the device identical with installation diagram. Make fixture hole on chassis face the three
plastic expansion bolts (in Step 1). Take 3 ST3.0 self-tapping screw out from the
accessories bag and fix them on the three plastic expansion bolts to secure the chassis on
installation surface.
Step 4
Line up the dome camera protection enclosure and follow step 1 reversely to put it back.
Use the inner hex wrench from the accessories bag to fasten the 3 hex screws. For
Micro-SD card installation, please refer to Chapter 3.3.
See Figure 3- 2 for grounding hole (GND).
Figure 3- 2
Note: If connect the GND to ground lead, may improve device reliability. The GND
locates next to exit hole on chassis and the GND screw is M3.
3.3 Micro SD Card Installation
Warning!
Please unplug the device power cable and then shutdown the device before you
install the Micro SD card.
Please make sure the wire between power panel and device motherboard is firm,
15
otherwise may cause abnormity.
Please put the enclosure back and fasten the screws tightly to prevent dust.
Step 1
Please refer to Step 1 in chapter 3.2 to open the device protection enclosure.
Step 2
Please find the “SD” mark inside the device according to Figure 3- 3. Insert Micro-SD card
and put the enclosure back.
Figure 3- 3
3.4 Manual Zoom Lens Focus Operation
The lens of the HD panorama network camera is 180°, no manual zoom is required.
16
4 Quick Configuration Tool
4.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same
time, you can use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
4.2 Operation
Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure
4-1.
In the device list interface, you can view device IP address, port number, subnet mask,
default gateway, MAC address and etc.
Figure 4-1
Select one IP address and then right click mouse, you can see an interface is shown as in
Figure 4-2.
Note:
You can set the IP address, subnet mask and gateway for the network camera and PC.
Please note network camera IP address and PC IP address shall be in the same network
segment if there is no router. Network camera default IP address is 192.168.1.108. If
there is a router, please set the corresponding gateway and subnet mask.
The factory default user name is admin and password is admin. For security reasons,
please modify your password after you first login.
For detailed WEB operation, please refer to the Network Camera Web Operation Manual
in the resource CD.
17
Figure 4-2
Select the “Open Device Web” item; you can go to the corresponding web login interface.
See Figure 4-3.
Figure 4-3
If you want to modify the device IP address without logging in the device web interface,
you can go to the configuration tool main interface to set.
In the configuration tool search interface (Figure 4-1), please select a device IP address
and then double click it to open the login interface. Or you can select an IP address and
then click the Login button to go to the login interface. See Figure 4-4.
In Figure 4-4, you can view device IP address, user name, password and port. Please
modify the corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP
port in Web Network interface. Otherwise, you cannot login the device.
If you are using device background upgrade port 3800 to login, other setups are all invalid.
18
Figure 4-4
After you logged in, the configuration tool main interface is shown as below. See Figure
4-5.
Figure 4-5
For detailed information and operation instruction of the quick configuration tool,
please refer to the Quick Configuration Tool User’s Manual included in the
resources CD.
19
5 Web Operation
Input your IP
address here
This series network camera products support the Web access and management via PC.
Web includes several modules: Monitor channel preview, system configuration, alarm and
etc.
5.1 Network Connection
Please follow the steps listed below for network connection.
1. Make sure the network camera has connected to the network properly.
2. Please set the IP address, subnet mask and gateway of the PC and the network
camera respectively. Network camera default IP address is 192.168.1.108. Subnet
mask is 255.255.255.0. Gateway is 192.168.1.1
3. Use order ping ***.***.***.***(* network camera address) to check connection is OK or
not.
5.2 Login and Main Interface
Open IE and input network camera address in the address bar.
For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108
in IE address bar. See Figure 5- 1.
Figure 5- 1
The login interface is shown as below. See Figure 5- 2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please change your password after you first login.
20
Figure 5- 2
If it is your first time to login in, system pops up warning information to ask you whether
install control webrec.cab or not after you logged in for one minute. Please click OK button,
and system will automatically install the control. When system is upgrading, it will
overwrite the previous Web too.
If you can’t download the ActiveX file, please check whether you have installed the plug-in
to disable the control download. Or you can lower the IE security level. See Figure 5- 3.
Figure 5- 3
After you logged in, you can see the main window. See Figure 5- 4.
21
Figure 5- 4
Please refer to the Web Operation Manual included in the resource CD for detailed
operation instruction.
5.3 Panorama Function on Web
There is a panorama icon at the lower-left corner of web interface and you can click it to
view installation mode and display mode at the right.
Please set installation mode according to actual installation condition.
5.3.1 Installation Mode
There are three modes: wall mount, in-ceiling and ground.
Wall mount: It is wall mount and the camera is pointing to the front.
In-ceiling: It is the in-ceiling mount and the camera is pointing to the bottom.
Ground: It is the ground installation and the camera is pointing to the top.
See Figure 5- 5.
22
Figure 5- 5
5.3.2 Display Mode
There are four modes: 360°1-window, dual-picture panorama, 1-window and 90°
4-window
360° 1-window: It takes the whole panorama and is one-window 360 degrees
panorama.
Dual-picture panorama: It is the dual-window 180 degrees panorama.
1-window: It is to display one of the four windows. It can show the video around the
360 degrees panorama. You can select video and then implement corresponding
operation.
Where you can:
1. Adjust camera direction via arrow keys. Click OK to restore default position.
2. Step length is mainly used for speed adjustment as the longer the step, the higher the
speed. Zoom step length is to adjust zoom speed; movement step length is to adjust
rotation speed per step; rotation step length is to adjust clockwise/counterclockwise
rotation speed.
90°4-window: Panorama 360 digress is divided into four windows. Each window has
90 digress and totally displayed in four channels.
23
6 FAQ
Bug
Solution
I cannot boot up
the device.
Please click RESET button for at least five seconds to restore factory
default setup.
Micro SD card
write times
Do not set the Micro SD card as the storage media to store the
schedule record file. It may damage the Micro SD card duration.
I cannot use the
disk as the storage
media.
When disk information is shown as hibernation or capacity is 0,
please format it first (Via Web).
I cannot upgrade
the device via
network.
When network upgrade operation failed, you can use port 3800 to
continue upgrading.
Recommended
Micro SD card
brand
Kingston 4GB, Kingston 16GB, Kingston 32GB, Transcend 16GB，
SanDisk 4GB, SanDisk 32GB.
Usually we recommend the 4GB (or higher) or industry-level high
speed card in case the slow speed results in data loss.
Save config
When you are done with config, to ensure the config is saved on
storage media, we recommend you to reboot the device via software.
General power
adaptor
The suggested environment temperature of a general power adaptor
is 0~40 ℃, and for other temperatures, a industry-level power
adaptor is required.
24
Appendix Toxic or Hazardous Materials or Elements
Component Name
Toxic or Hazardous Materials or Elements
Pb
Hg
Cd
Cr VI
PBB
PBDE
Circuit Board Component
○ ○ ○ ○ ○
○
Device Case
○ ○ ○ ○ ○
○
Wire and Cable
○ ○ ○ ○ ○
○
Packing Components
○ ○ ○ ○ ○ ○ Accessories
○ ○ ○ ○ ○
○
O: Indicates that the concentration of the hazardous substance in all homogeneous
materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all
homogeneous materials in the parts is above the relevant threshold of the
SJ/T11363-2006 standard. During the environmental-friendly use period (EFUP) period,
the toxic or hazardous substance or elements contained in products will not leak or mutate
so that the use of these (substances or elements) will not result in any severe
environmental pollution, any bodily injury or damage to any assets. The consumer is not
authorized to process such kind of substances or elements, please return to the
corresponding local authorities to process according to your local government statutes.
Note
This user’s manual is for reference only. Slight difference may be found in user
interface.
All the designs and software here are subject to change without prior written
notice.
All trademarks and registered trademarks mentioned are the properties of their
respective
owners.
If there is any uncertainty or controversy, please refer to the final explanation
of us.
Please visit our website for more information.
Loading...