Icom RS-R301 User Manual
REMOTE CONTROL SOFTWARE
RS-R30I
The RS-R30I is an iOS application to control the IC-R30 from your iOS device. These instructions show how to
use the application. Refer to the IC-R30 BASIC MANUAL for the Bluetooth connection details.
Major functions
Single band display
Dual band display
VFO Mode Setting a frequency
Selecting a receive
mode
Duplex setting
Tone Setting
NV, ANL, AFC, VSC
settings
TS setting
Memory Mode Display a memory
channel
Writing a memory
channel
Scan Start/Stop scan
SKIP settings
Adjusting VOL/SQL
Recording
ATT settings
RF gain settings
N/A: Not Applicable
System requirements
✓
✓
✓
✓
✓
✓
✓
✓
✓
N/A
✓
✓
✓
✓
✓
✓
Operating notes
• ConrmtheIC-R30ʼsSerialportfunctionissetto
“CI-V (Echo Back OFF)”
( [MENU] > Bluetooth Set > Data Device Set >
Serialport Function)
• Pair the IC-R30 from the application. Refer to the
IC-R30 ADVANCED MANUAL for details.
• Bluetooth LE is used to connect with the receiver,
so there may be a time delay between the receiver’s
operation and the display on the data device.
The time delay may happen while scanning, or
using a Bluetooth headset.
• Bluetooth connection may be canceled when:
- The device’s screen is locked.
- Wi-Fi is turned ON on your iOS device.
- The application is in the Background mode.
- The surrounding radio wave environments affect
the connection.
- Connecting or disconnecting a Bluetooth headset.
• When receiving pictures using D-STAR “FAST
mode,” the headset audio will be temporarily
interrupted because of the receiver’s Bluetooth unit
limitations.
• The application does not output the audio received
by the receiver.
• Restart the application when you edited the Memory
channel on the IC-R30.
• The application supports only portrait orientation. It
does not support Auto Rotate.
INSTRUCTIONS
The following system is required to use the
application. (As of September 2018)
Data device
iPhone or iPad with 64 bit CPU*.
* iPhone 5S or later, iPad Air, and so on.
Operating system
iOS version 9.0 or later
L Download the application from the App Store.
Receiver
IC-R30
Disclaimer
• The application may not work, depending on the
iOS version, installed applications, and so on.
• These Instructions are based on using iPad (iOS
11.4.1). Depending on the iOS version or setting,
the indications or items may differ.
• The screen shots on these Instructions are just
examples, so the contents may differ from the
actual ones.
- 1 -
Function display
3
1
Touch the sub band area to
set it as a main band.
Group*/Channel
selector buttons
* Usable for only the Memory
mode
2
Tub bar
1
Touch to display the screen, as shown below.
“Control”
Displays the frequency or memory channel that the
IC-R30 is receiving. You can change the receive
mode, or start/stop scanning.
“Settings”
Displays functions usable in the current receiving
mode. Refer to the IC-R30 ADVANCED MANUAL for
each function details.
“VOL/SQL”
z Select whether or not to synchronize the A band
and B band audio level.
z Adjust the volume and squelch.
Menu bar
2
“Control”
Touch to display the “Control,” “Settings,” or
“VOL/SQL” screen.
“Application Settings”
Edit the application settings such as Bluetooth
connection, CI-V address, and so on.
Touch buttons
3
Touch to use assigned functions, or edit the receiver
settings, as shown below.
L The grayed out buttons are not usable.
[MAIN]/[DUAL]
z Touch to set the A or B band as the main band.
z Long touch to turn the Dualwatch function ON or
OFF.
[MODE]
Touch to display the Receive mode options.
[VFO]/[MR]
Touch to select the VFO mode or Memory mode.
[RFG]
Touch to display the RF Gain options.
[ATT]
Touch to display the Attenuator options.
[TS]
Touch to display the Tuning step options.
[●REC]
Touch to start or stop voice recording on the IC-R30.
[SCAN]
Touch to start or stop scanning.
L TouchChannelselectorbuttons(▲/▼)tochangethe
scanning direction.
[SKIP] (For only the Memory mode)
Touch to display the Skip/Program Skip options.
- 2 -
Loading...