Ice-O-Matic CD40022 User Manual

SERVICE/INSTALLATION MANUAL

e

HOTEL DISPENSER

MODEL CD40030 and CD40022

Ice-O-Matic
11100 East 45th Av
Denver, Colorado 80239
Part Number 9081317-01 Print Date 10/08

SERVICE PARTS MANUAL

22 INCH WIDE ICE SERIES CUBERS

MODEL-ICE0320, ICE0520

Includes 50Hz. Units

ICE-O-Matic
11100 East 45th Ave
Denver, Colorado 80239

Part Number 9081297-01 PD04/02 Rev1/05

Introduction CD40030/CD40022

To the owner or user: This product manual is a source of information about the installation,
start up, cleaning, maintenance and repair of the product.

Table of Contents

Introduction Page 1
General Description and Warranty Information Page 2
Specification/Limitations Page 5
Product Description Page 6
Unpacking Page 7
Installation-Plumbing Page 8
Installation-Electrical and Ice Machine Assembly Page 9
Final Check List/Initial Start Up Page 10
Dispenser Use Page 11
General Care and Cleaning Page 12
Maintenance Page 14
Adjustments Page 15
Service Diagnosis Page 16
Wiring Diagram-115 volt 60Hz. Basic and Water Station Page 17
Wiring Diagram-Coin Mechanism Page 18
Wiring Diagram-230 volt, 50HZ basic Page 19

Ice-O-Matic
11100 E. 45th Ave.
Denver, Co. 80239
800-423-3367

The CD400 Service Parts Manual is available separately, Part Number 9081317-02

Page 1

General Description CD40030/CD40022

The CD40022 is a 22 inch wide hotel/motel cubed ice dispenser. It is designed to use an
Ice-O-Matic ICE0320 or ICE0520 cube ice machine as the source for ice.

The CD40030* is a 30 inch wide version of the CD40022 and is designed to use Ice-O-Matic
ICE0250 through ICE0500 cubers as its source of ice. Note: 22 inch wide ice machines
are not for use on the 30 inch wide dispensers.

*Higher capacity cubers, ICE0606, ICE0806 and ICE1006 may also be used, but they require
230-volt power.

Ice from the cuber falls into the insulated hopper, where it is stored until needed. When a
user pushes the dispense chute a rotating wheel scoops the ice up to the top front of the
hopper where there is an outlet to the ice chute. Ice is directed into the users container.

Flaked or nugget ice should not be used in these dispensers.
Do not double stack cubers on these dispensers.
Condensate drain pumps are not recommended for drainage.
This is not a waterglass style dispenser.

Basic Specifications

Model Dimensions Electrical Model Description Bin Storage

CD40022 22 x 53 x 33½ 115/60/1 Basic 22” Model 60 Hz. 120 Lbs.
CD40522 22 x 53 x 33½ 230/50/1 Basic 22” Model 50 Hz. 120 Lbs.
Note: The factory installed Water Dispenser and Coin /Token features are not available on the
22-inch wide Basic Push Button dispenser and are not available as a field installed kits.

CD40030 30 x 53 x33½ 115/60/1 Basic 30” Model 60 Hz 180 Lbs.
CD40130 30 x 53 x33½ 115/60/1 Basic 30” / Water Filler 180 Lbs.
CD40230 30 x 53 x33½ 115/60/1 Coin/Token 180 Lbs.
CD40530 30 x 53 x33½ 230/50/1 Basic 30” Model 50 Hz. 180 Lbs.
Note: The factory installed Water Dispenser is only available on the 30-inch wide Basic Push
Button dispenser and is not available as a field installed kit. The Coin/Token model is not
available with a Water Filler and is not available as a field installed Water Filler Kit.

Basic models dispense ice when their chute is pushed and will continue to dispense ice until
the chute is released or the bin is emptied. Coin/Token models require a coin or token first.
Tokens are available from Ice-O-Matic, the part number for 500 tokens is TKNS. Water
Dispenser models are basic models with a factory installed separate water dispenser.

Bin Thermostats

Bin Thermostats are not required in ICE series cubers on CD400 Series Dispensers.

Warranty
The CD40030 and CD40022 have a 3 year parts and labor warranty from date of install.

W x H x D Capacity ARI
With 6” Legs

Page 2

General Description CD40030/CD40022

Dimensions
CD40022

558.8
22"

ICE FILL STATION

8 3/4 [221.5] HIEGHT

13 1/2 [342.9] WIDTH

8 1/2 [215.9] DEPTH

1351.3
53 1/4"

152.4
6"

FRONT

650.6

25 5/8"

850.1

33 1/2"

RIGHT SIDE

Page 3

General Description CD40030/CD40022

Dimensions
CD40030

254.8
10"

WATER VALVE HEIGHT

(WATER FILLER ONLY - Optional)

609.6
24"

762.4
30"

FRONT

152.4
6"

17 3/4"

1351.3
53 1/4"

451.1

ICE FILL STATION

8 3/4 [221.5] HIEGHT

13 1/2 [342.9] WIDTH

8 1/2 [215.9] DEPTH

(2) 5/16-18 UNC

ICE HEAD MOUNTING

24.1
1"

650.5

25 5/8"

849.4

33 1/2"

RIGHT SIDE

Machine Support

Screwed to Back Panel

179.1
7"

189.4
7 1/2"

3/4 FPT
DRAIN

189.7
7 1/2"

BACK

POWER
CORD

WATER INLET

3/8 FLARE

(WATER FILLER ONLY)

444.4

17 1/2"

Page 4

Specification & Limitations CD40030/CD40022

This dispenser is designed to be installed and operated indoors, in a controlled
environment. It’s minimum and maximum operating temperature limits are the same as

those for the ice machine.
Minimum Maximum

Air Temp 50oF 100oF
Water Pressure* 20 psi 60 psi * for water dispenser model

Check the dispenser nameplate, located on the back of the cabinet for specific information.
Ice-O-Matic reserves the right to make design changes and/or improvements at any time.
Specifications and designs are subject to change without notice.
Ice-O-Matic assumes no liability or responsibility of any kind for products manufactured by
Ice-O-Matic that have been altered in any way, including the use of any parts and/or other
components not specifically approved by Ice-O-Matic.

Models
There are three versions of the CD40030 dispensers: Basic, Coin/token and Water
Dispenser. The Basic version is constructed to deliver ice when the ice chute is pushed in,
and it continues to vend ice as long as the ice chute is held in or until the bin is empty.

The Coin/token version is designed to deliver ice after a coin or token is inserted into the coin
slot and then the ice chute is pushed in. Ice vending is limited to a preset time per coin or
token use. Coins or tokens are collected in a coin box at the bottom of the dispenser. A keyed
door allows access to the coin box without removing the front panel.

The Water Dispenser version is a Basic version with a mechanical water faucet added to the
left of the ice chute. Water is dispensed whenever the faucet lever is pushed back. The
CD40030 is available in all versions; the CD40022 is only available as a Basic model.

The Basic models of the CD40022 and CD40030 are available in 230 volt 50 Hz electrical for
those countries with that type of electrical service.

Kits: Bin tops and bin thermostats are not required. No other kits are available.
Warranty

other than that an unmodified new part purchased directly from Ice-O-Matic, Ice-O-Matic
Distributors, or any of its authorized service agents and/or the part being used is modified
from its original configuration, this warranty will be void. Further, Ice-O-Matic and its affiliates
will not be liable for any claims, damages or expenses incurred by customer which arises
directly or indirectly, in whole or in part, due to the installation of any modified part and/or part
received from an unauthorized service center. Adjustments are not covered under warranty.

Warranty Procedure
Ice-O-Matic authorized representative travels to the installation address to perform warranty
service, the service representative will advise customer the warranty is void. Such service
call will be billed to the customer at the authorized service center’s then-applicable time and
material rates.

If, during the warranty period, customer uses a part for this Ice-O-Matic equipment

If the customer is using a part that results in a voided warranty and an

Page 5