IBM 6734-AG9, 6734-AB9 User Manual

L170

User's Guide

IBM ThinkVisionTM Monitor L170

English

iii

First Edition (April/2004)

Note: For important information, refer to the Monitor Safety and Warranty manual that comes with this monitor.

ENGLISH

Safety (Read first).......................................................................................................2

Setting up the monitor...............................................................................................5

Product description..............................................................................................5

Handling instructions............................................................................................5

Kensington security slot.......................................................................................6

Workplace preparation.........................................................................................7

Adjusting the monitor position..............................................................................7

Working practices.................................................................................................8

Caring for your monitor........................................................................................8

Connecting your monitor......................................................................................9

Turning on your monitor.....................................................................................10

Device driver installation.........................................................................................11

Windows 95/98...................................................................................................11

Windows 2000/Me..........................................................................................................12

Windows XP...................................................................................................................13

Automatic Image setup............................................................................................14

Image setup.......................................................................................................14

Image setup for DOS.........................................................................................15

Image setup for Windows 95, Windows 98, Windows 2000, Windows NT, Windows Me, or Windows XP

..................................................................................

Manual Image setup.................................................................................................17

Adjusting your LCD monitor ...................................................................................18

User controls......................................................................................................18

On-screen display (OSD) controls.....................................................................19

Further information..................................................................................................22

Display modes ...................................................................................................22

Power management...........................................................................................23

Product disposal ................................................................................................23

Troubleshooting.......................................................................................................24

Help and service information .............................................................................26

Specifications...........................................................................................................27

Service information..................................................................................................28

Notices and trademarks...........................................................................................29

Contents

ENGLISH

Always observe the following precautions to reduce the risk of injury and property damage.

Do not attempt to service a product yourself unless instructed to do so by the IBM Support Center. Use only an IBM authorized service provider who is approved to repair your particular product.

Note: Some parts can be upgraded or replaced by the customer. These parts are referred to as Customer Replaceable Units, or CRUs. IBM expressly identifies CRUs as such, and provides documentation with instructions when it is appropriate for customers to replace those parts. You must closely follow all instructions when performing such replacements. Always make sure that the power is turned off and that the product is unplugged from any power source before you attempt the replacement. If you have any questions or concerns, contact the IBM Support Center.

Use only the power cords and power adapters supplied by the product manufacturer.

Never wrap a power cord around the power adapter or other object. Doing so can stress the cord in ways that can cause the cord to fray, crack or crimp. This can present a safety hazard.

Always route power cords so that they will not be walked on, tripped over, or pinched by objects.

Protect the cord and power adapters from liquids. For instance, do not leave your cord or power adapter near sinks, tubs, toilets, or on floors that are cleaned with liquid cleansers. Liquids can cause a short circuit, particularly if the cord or power adapter has been stressed by misuse. Liquids can also cause gradual corrosion of the power cord terminals and/or the connector terminals on the adapter which can eventually result in overheating.

Always connect power cords and signal cables in the correct order and ensure that all power cord connectors are securely and completely plugged into receptacles.

Do not use any power adapter that shows corrosion at the ac input pins and/or shows signs of overheating (such as deformed plastic) at the ac input or anywhere on the power adapter.

Do not use any power cords where the electrical contacts on either end show signs of corrosion or overheating or where the power cord appears to have been damaged in any way.

Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you use are rated to handle the electrical requirements of the product. Never overload these devices. If power strips are used, the load should not exceed the power strip input rating. Consult an electrician for more information if you have questions about power loads, power requirements, and input ratings.

If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician.

Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement.

Some products are equipped with a three-pronged plug. This plug fits only into a grounded electrical outlet. This is a safety feature. Do not defeat this safety feature by trying to insert it into a non-grounded outlet. If you cannot insert the plug into the outlet, contact an electrician for an approved outlet adapter or to replace the outlet with one that enables this safety feature. Never overload an electrical outlet. The overall system load should not exceed 80 percent of the branch circuit rating. Consult an electrician for more information if you have questions about power loads and branch circuit ratings.

Be sure that the power outlet you are using is properly wired, easily accessible, and located close to the equipment. Do not fully extend power cords in a way that will stress the cords.

Connect and disconnect the equipment from the electrical outlet carefully.

All IBM personal computers contain a non-rechargeable coin cell battery to provide power to the system clock. In addition many mobile products such as ThinkPad notebook PCs utilize a rechargeable battery pack to provide system power when in portable mode. Batteries supplied by IBM for use with your product have been tested for compatibility and should only be replaced with IBM approved parts.

Never attempt to open or service any battery. Do not crush, puncture, or incinerate batteries or short circuit the metal contacts. Do not expose the battery to water or other liquids. Only recharge the battery pack strictly according to instructions included in the product documentation.

Battery abuse or mishandling can cause the battery to overheat, which can cause gasses or flame to "vent" from the battery pack or coin cell. If your battery is damaged, or if you notice any discharge from your battery or the buildup of foreign materials on the battery leads, stop using the battery and obtain a replacement from the battery manufacturer.

Batteries can degrade when they are left unused for long periods of time. For some rechargeable batteries (particularly Lithium Ion batteries), leaving a battery unused in a discharged state could increase the risk of a battery short circuit, which could shorten the life of the battery and can also pose a safety hazard. Do not let rechargeable Lithium-Ion batteries completely discharge or store these batteries in a discharged state.

Computers generate heat when turned on and when batteries are charging. Notebook PCs can generate a significant amount of heat due to their compact size. Always follow these basic precautions:

• Do not leave the base of your computer in contact with your lap or any part of your body for an extended period when the computer is functioning or when the battery is charging. Your computer produces some heat during normal operation. Extended contact with the body could cause discomfort or, potentially, a skin burn.

• Do not operate your computer or charge the battery near flammable materials or in explosive environments.

• Ventilation slots, fans and/or heat sinks are provided with the product for safety, comfort, and reliable operation. These features might inadvertently become blocked by placing the product on a bed, sofa, carpet, or other flexible surface. Never block, cover or disable these features.

CD and DVD drives spin discs at a high speed. If a CD or DVD is cracked or otherwise physically damaged, it is possible for the disc to break apart or even shatter when the CD drive is in use. To protect against possible injury due to this situation, and to reduce the risk of damage to your machine, do the following:

• Always store discs in their original packaging

• Always store discs out of direct sunlight and away from direct heat sources

• Remove discs from the computer when not in use

• Do not bend or flex discs, or force them into the computer or their packaging

• Check discs for cracks before each use. Do not use cracked or damaged discs

ENGLISH

Setting up the monitor

Handling instructions

1. Lift the monitor by placing your hands where indicated by the arrow in the figure below.

2. Before using your monitor for the first time, remove the clear protective film from the front of the screen.

Product description

The IBM ThinkVision Monitor, L170, is a TFT LCD Color Monitor. It requires a computer with a suitable on-board sub-system or Video Adapter card that can support SXGA 1280 x 1024, XGA 1024 x 768, SVGA 800 x 600, or VGA 640 x 480 at 60Hz.

In addition to your monitor, your option package includes the following:

• User's Guide and Installation Files CD

• Monitor Safety and Warranty Information Manual

• IBM ThinkVision Monitor L170 Setup Guide

• Power Cord

• L170 ThinkVision Monitor

• Analog Interface Cable - Attached to Monitor

Do not support the monitor within the screen area. The Liquid Crystal Display is glass and can be damaged by rough handling or excessive pressure.

Kensington security slot

This slot can be used to connect to a locking cable. Locking cables can be purchased separately at most computer stores.

Kensington

security slot

ENGLISH

With the IBM Flat Panel

Monitor, you can adjust its position in various ways for maximum comfort.

Viewing angle

You can tilt the screen forward and backward as shown below in Figure A.

Figure A

Adjusting the monitor position

This section gives advice

on what you should consider before you set up your monitor.

Workplace preparation

Height

Position the monitor so that the top of the screen is slightly below your eye level when you sit at your workstation.

Orientation

1. Choose a position that gives the least reflection from lights and windows, usually at a right angle to any windows.

2. Position the monitor directly in front of you so that you do not have to twist your body to use it.

3. Tilt the monitor to a comfortable viewing angle.

Be sure to turn off the power before you perform any maintenance on the monitor. Clean your monitor as follows:

• Do not use solvents or abrasives.

• Gently wipe the covers and the screen with a soft cloth.

• Remove finger marks and grease with a damp cloth and mild detergent.

• Never use flammable cleaning materials to clean your IBM monitor or any other electrical apparatus.

Caring for your monitor

This section gives advice

on how you can work comfortably and reduce fatigue.

Rest

Take regular breaks. Vary your posture, stand up and stretch occasionally as prolonged use of computer workstations can be tiring.

Back

Sit back in your chair and use the backrest.

Hands

Adjust the seat height so that your forearms are approximately horizontal and your wrists are straight when using the keyboard. Your upper arms should be relaxed with your elbows near your body.

Use a light touch on the keyboard, keeping your hands and fingers relaxed. Allow a space in front of the keyboard to rest your wrists when not typing. Consider using a wristpad.

Eyesight

Working with monitors, in common with any prolonged close work, can be visually demanding. Look away from the screen periodically and have your eyesight checked regularly.

Screen settings

Set the screen brightness and contrast to a comfortable level. You may have to adjust these settings as the lighting changes during the day. Many application programs let you select color combinations which can help you to view in comfort. See the User controls section on page 18 for more information.

Working practices

+ 22 hidden pages