How it Works
IBM
Loading...
6636AC1
User Manual
33 pgs1.35 Mb0

IBM ThinkVision L150, 6636AC1 User Manual

Download
Page 1
L150
User's Guide
ThinkVisionTM Flat Panel Monitor
English
Page 2
DEUTSCH
English
Page 3
First Edition (June/2003)
Note: For important information, refer to the Monitor Safety and Warranty manual that comes with
this monitor.
Page 4
1
DEUTSCH
Contents
Safety (Read first) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Setting up the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Handling Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Workplace Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Adjusting the Monitor Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Working Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Caring for your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Turning on your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the Device Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Windows 95 or Windows 98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Windows 2000 or Windows Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Automatic Image Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Image Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Image Setup for DOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setup for Windows 95, Windows 98, Windows NT, Windows 2000, Windows Me or Windows XP 13
Manual Image Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Adjusting your LCD Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
User Controls Accessible Via On Screen Display (OSD) . . . . . . . . . . . . . . . . 15
On-Screen Display (OSD) Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Further Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Display Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Product Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Help and Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Notices and Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Page 5
2
.
í í í
Page 6
3
DEUTSCH
Setting up the Monitor
Product Description
The IBM ThinkVision L150 Monitor works with a computer with a suitable on­board sub-system or Video Adapter card that can support XGA 1024 x 768, SVGA 800 x 600, or VGA 640 x 480 at 75 Hz.
Your option package includes the following:
• IBM ThinkVision L150 Monitor
• User's Guide and Installation Files CD
• Monitor Safety and Warranty Information Manual
• L150 Setup Guide
• Power Cord
• Analog Interface Cable - Attached to Monitor
Handling Instructions
Do not support the monitor within the screen area. The Liquid Crystal Display is glass and can be damaged by rough handling or excessive pressure.
1. To lift the monitor, place your hands on the areas indicated below.
2. Before using your monitor for the first time, remove the clear protective film from the front of the screen.
T
h
i
n
k
V
i
s
i
o
n
Page 7
4
Workplace Preparation
This section gives advice on what you should consider
before you set up your monitor.
Height
Position the monitor so that the top of the screen is slightly below your eye level when you sit at your workstation.
Orientation
Choose a position that gives the least reflection from lights and windows, usually at a right angle to any windows. Position the monitor directly in front of you so that you do not have to twist your body to use it. Tilt the monitor to a comfortable viewing angle.
Adjusting the Monitor Position
Viewing Angle
You can tilt the screen backward and forward as shown below.
Working Practices
This section gives
advice on how you can work comfortably and reduce fatigue.
Rest
Take regular breaks. Vary your posture, stand up and stretch occasionally as prolonged use of computer workstations can be tiring.
T
h
i
n
k
V
i
s
i
o
n
Page 8
5
DEUTSCH
Back
Sit back in your chair and use the backrest.
Hands
Adjust the seat height so that your forearms are approximately horizontal and your wrists are straight when using the keyboard. Your upper arms should be relaxed with your elbows near your body.
Use a light touch on the keyboard, keeping your hands and fingers relaxed. Allow a space in front of the keyboard to rest your wrists when not typing. Consider using a wristpad.
Eyesight
Working with monitors, in common with any prolonged close work, can be visually demanding. Look away from the screen periodically and have your eyesight checked regularly.
Screen settings
Set the screen brightness and contrast to a comfortable level. You may have to adjust this as the lighting changes during the day. Many application programs let you select color combinations which can help you to view in comfort. See the User Controls Accessible Via On Screen Display (OSD) section on page 15 for more information.
Caring for your Monitor
Be sure to turn off the power before you perform any maintenance on the monitor. Clean your monitor as follows:
• Gently wipe the device covers and the screen with a soft cloth.
• Remove finger marks and grease with a damp cloth and mild detergent; do not use solvents or abrasives.
• Never use flammable cleaning material to clean your IBM monitor or any other electrical apparatus.
Page 9
6
Connecting your Monitor
Be sure to read the 'Safety' Information located in the Monitor Safety and Warranty Information Manual before carrying out this procedure.
1. Turn off your computer and all attached devices.
2. Connect the signal cable to the video port on the back of your computer. This port might be directly attached to your computer (figure A), or it might be part of a video adapter card (figure B). The video port on your computer or video adapter card might be blue to match the blue connector on your monitor’s video cable.
3. The supplied power cord is not attached to the monitor. If you would like to route the power cord through the stand, follow the instructions below:
a. Tilt the monitor all the way forward.
b. Hold the top of the cable cover (a) and pull it off. c. Gently lift the stand cover (b) and slide it backwards and off the stand.
b
a
forward tilt
Page 10
7
DEUTSCH
d. Connect the power cord to the power port on the back of your monitor as shown in the illustration below.
e. Put the stand cover (e) back then put the cable cover (f) back.
4. Insert the plug into a properly grounded electrical outlet.
Turning on your Monitor
1. Turn on the power source and your computer.
2. To turn on your monitor, push and release the power switch marked . To turn off your monitor, push and release the power switch again.
3. Turn on the monitor and then the computer.
4. To update or install device drivers, follow the instructions in the Installing the Device Driver section on page 8.
5. To optimize the displayed image, run Image Setup by following the instructions in the Automatic Image Setup section on page 11.
e
f
forward tilt
Page 11
8
Installing the Device Driver
Installing the Device Driver for Windows 95 or Windows 98
This section must be completed before continuing with the Windows 95 or Windows 98
Image Setup section on
page 13.
To install the device driver in Microsoft® Windows® 95 or Windows 98, do the following:
Note: You must download files from the User's Guide and Installation Files CD to use the Plug and Play feature in Windows 95 or Windows 98.
1. Turn off the computer and all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow your computer to start the Windows 95 or Windows 98 operating system. Your computer’s Plug and Play code might warn you that your system hardware has changed. This means that it has detected your new monitor for the first time.
4. Open the Display Properties window by clicking Start > Settings > Control Panel and then double-clicking on the Display icon.
On LCD monitors, unlike
CRTs, a faster refresh rate does not improve display quality. For optimal performance, use 1024 x 768 at a refresh rate of 60Hz.
5. Click the Settings tab.
6. If you are using Windows 95, do the following:
a. Click the Change Display Type button.
b. Click the Change Monitor Type button.
If you are using Windows 98, do the following:
a. Click the Advanced button.
b. Click the Monitor tab. c. Open the Upgrade Device Driver Wizard window by clicking on the
Change button and then select the Next button.
d. Click the “Display a list of the known drivers for this device so that I can choose a specific driver” and then select the Next button.
7. Insert the User’s Guide and Installation Files CD into the CD drive and
click the Have Disk button.
8. Click OK.
9. Ensure that the CD drive letter is selected, and then select the DRIVERS folder.
10. Select IBM ThinkVision LCD L150 monitor and click OK. The files will be copied from the CD to your hard disk drive.
11. Close all open windows and remove the CD.
Page 12
9
DEUTSCH
12. Restart the computer. The system will automatically select the maximum refresh rate and corresponding Color Matching Profiles.
Installing the Device Driver for Windows 2000 or Windows Me
This section must be completed before continuing with the Windows 2000 or Windows Me
Image Setup section
on page 13.
To install the device driver in Microsoft Windows 2000 Professional or Microsoft Windows Millennium Edition (Me), do the following:
Note: You must download files from the User's Guide and Installation Files CD to use the Plug and Play feature in Windows 2000 or Windows Me.
1. Turn off the computer and all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow your computer to start the Windows 2000 or Windows Me operating system.
On LCD monitors, unlike
CRTs, a faster refresh rate does not improve display quality. For optimal performance, use 1024 x 768 at a refresh rate of 60Hz.
4. Open the Display Properties window by clicking Start > Settings > Control Panel and then double-clicking on the Display icon.
5. Click the Settings tab.
6. Click the Advanced button.
7. Click the Monitor tab.
8. Click the Properties button.
9. Click the Driver tab.
10. Open the Upgrade Device Driver Wizard window by clicking on Change button and then select the Next button.
11. Select “Display a list of the known drivers for this device so that I can choose a specific driver” and then click the Next button.
12. Insert the User’s Guide and Installation Files CD into the CD drive and click the Have Disk button.
13. Click OK.
14. Ensure that the CD drive letter is selected, and then select the DRIVERS folder.
15. Select IBM ThinkVision LCD L150 monitor and click OK. The files will be copied from the CD to your hard disk drive.
16. Close all open windows and remove the CD.
17. Restart the computer. The system will automatically select the maximum refresh rate and corresponding Color Matching Profiles.
Page 13
10
Installing the Device Driver for Windows XP
This section must be completed before continuing with the Windows XP
Image Setup
section
on page 13.
To install the device driver in Microsoft Windows XP, do the following:
Note: You must download files from the User's Guide and Installation Files CD to use the Plug and Play feature in Windows XP.
1. Turn off the computer and all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow your computer to start the Windows XP operating system.
4. Open the Display Properties window by clicking Start > Settings > Control Panel and then double-clicking on the Display icon.
On LCD monitors, unlike
CRTs, a faster refresh rate does not improve display quality. For optimal performance, use 1024 x 768 at a refresh rate of 60Hz.
5. Click the Settings tab.
6. Click the Advanced button.
7. Click the Monitor tab.
8. Click the Properties button.
9. Click the Driver tab.
10. Open the Hardware Update Wizard window by clicking on Update Driver and then click the Next button.
11. Select “Install from a list or Specific location(Advanced)” and then click the Next button.
12. Insert the User’s Guide and Installation Files CD into the CD drive and click the Have Disk button.
13. Click OK.
14. Ensure that the CD drive letter is selected, and then select the DRIVERS folder.
15. Select IBM ThinkVision LCD L150 monitor and click OK. The files will be copied from the CD to your hard disk drive.
16. Close all open windows and remove the CD.
17. Restart the computer. The system will automatically select the maximum refresh rate and corresponding Color Matching Profiles.
Page 14
11
DEUTSCH
Automatic Image Setup
Image Setup ( )
The Setup Utility included on the installation CD is for displaying dot patterns. They do not replace or modify the display driver.
The Image Setup (
)
instructions require the monitor to warm up for 15 minutes. This is not required for normal operation.
By pressing the Auto key, you will have direct access to Automatic Image Setup Adjustment.
When you first use your monitor you must perform Image Setup ( ). This procedure sets up your monitor to process the video signals from your computer without image discoloration or smearing. After you perform Image Setup ( ), the settings are stored and used each time you turn on the monitor.
To optimize the displayed image a set-up utility is provided on the CD. Operation of the utility is dependent on the operating system on your computer. For correct operation locate the operating system on your computer from the table below and follow the appropriate instructions. You can choose to run
IMAGE SETUP ( ) for each operating system that you use.
This means that if you use your monitor while running any version of Windows and also use it from within DOS (not a DOS window), you must run
IMAGE SETUP () for both Windows and DOS. You can run versions of IMAGE S
ETUP () in any order.
Before you begin
IMAGE SETUP ( ) for your computer:
1. Make sure the computer’s video mode is set in the range of the supported screen resolution shown in the table on page 20.
The
IMAGE SETUP ()
process only applies to the current screen mode. When a new mode is selected, repeat this section to reset the monitor.
You should perform IMAGE SETUP ( ) for each screen mode you use.
Operating System Corresponding Image Setup Procedure
DOS
Image Setup ( ) for DOS on page 12
Windows 95, Windows 98, Windows 2000,
Microsoft Windows NT®, Windows Me or Windows XP
Image Setup ( ) for Windows 95, Windows 98,
Windows NT, Windows 2000, Windows ME,
Windows XP on page 13
Page 15
12
Image Setup for DOS
To set up the monitor automatically in DOS, do the following:
If the monitor is in sleep
mode, it may automatically turn off while you are waiting for it to warm up. If this happens, turn off the monitor and turn it on again after a few seconds.
1. Turn on the monitor first; then turn on the computer.
If the message CHECK SIGNAL CABLE is displayed, or if nothing is displayed, check:
• that the video interface cable is connected properly.
• the correct video adapter card is installed.
• the correct supported display mode is selected for your computer.
If you are using PC-DOS/V,
change to U.S. mode by typing CHEV US and pressing ENTER at the command prompt.
2. Wait approximately 15 minutes, until the monitor warms up.
3. Insert the User’s Guide and Installation Files CD into the computer CD­ROM drive.
4. Display the command prompt screen of the DOS full-screen display.
5. Type d:\ (change the drive letter to match your CD-ROM drive if it is not drive D).
6. Type TESTPAT and press ENTER.
7. Select from the screen the number for the color or text mode you want to set up.
8. Select from the screen the number for the video mode you want to set up. You can repeat this process for as many of the color and video modes as you need.
The size and diversity of the dot pattern varies with the
screen resolution.
9. When the dot pattern appears, press the Image Setup ( ) button at the bottom of the monitor. This activates the
IMAGE SETUP ()
procedure, which will optimize the display settings with the provided dot patterns.
The screen will momentarily turn black while auto adjustment proceeds.
10. When finished, the Auto Adjustment menu disappears and the screen returns to a normal display.
11. Press the ESCAPE key to exit the test pattern program.
12. Type EXIT at the command prompt to return to Windows.
If you use other operating systems, perform the appropriate Image Setup ( ) for those systems using instructions given in "Image Setup ( ) for
Windows 95, Windows 98, Windows NT, Windows 2000, Windows ME, Windows XP on page 13".
Page 16
13
DEUTSCH
Setup for Windows 95, Windows 98, Windows NT, Windows 2000, Windows Me or Windows XP
To set up the monitor automatically in Windows 95, Windows 98, Windows NT, Windows 2000, Windows Me, or Windows XP, do the following:
If the monitor is in sleep
mode, it may automatically turn off while you are waiting for it to warm up.
1. Turn on the monitor and then the computer.
If the message CHECK SIGNAL CABLE is displayed, or if nothing is displayed, check:
• that the video interface cable is connected properly.
• the correct video adapter card is installed.
• the correct supported display mode is selected for your computer.
2. Wait approximately 15 minutes, until the monitor warms up.
3. Drag the icon bar and tool bar, if they are displayed, to the bottom of the screen.
4. Insert the User’s Guide and Installation Files CD into the computer CD- ROM drive.
The size and diversity of the dot pattern varies with the
screen resolution.
5. Check the operating system installed on your computer and follow the instructions from the table below.
Operating system
installation steps
6. When the test pattern appears, press the Image Setup ( ) button at the bottom of the monitor. This activates the
IMAGE SETUP procedure,
which will optimize the display settings with the provided test patterns.
The screen will momentarily turn black while auto adjustment proceeds.
7. When finished, the Auto Adjustment menu disappears and the screen returns to a normal display.
8. Press the
ESC key to return to Windows.
You have completed the monitor setup for Windows. If you are using the DOS operating system, go to Image Setup ( ) for DOS on page 12.
Operating System Step 1 Step 2 Step 3
Windows 95, Windows 98, Windows 2000, Windows NT, Windows Me or Windows XP
Select
START
Select
RUN
Type D:\TESTPAT (change
the drive letter to match your
CD-ROM drive if it is not drive
D) and press ENTER
Page 17
14
Manual Image Setup
Normally, you can complete the setup procedure using IMAGE SETUP (); however, if your screen image is still distorted after you perform
IMAGE SETUP
( ) or the User’s Guide and Installation CD does not run on your system, perform
MANUAL SETUP.
If the monitor is in sleep
mode, it might automatically turn off while you are waiting for it to warm up.
1. Have your monitor turned on for about 15 minutes, until the monitor warms up.
2. Display the image you most frequently use on the screen.
3. Press the OSD Enter button at the bottom of the bezel to display the initial OSD menu.
4. Use the button to select the Image Setup icon ( ) and press the OSD Enter button to access.
5. Use the button to select Manual. Press Enter and Clock becomes highlighted. Press Enter again and adjust the screen quality settings. Press Enter twice to select Phase, the right arrow icon, and then Enter again to select phase. Adjust Phase, then press Enter twice to save and exitsub-menu.
6. Press the Exit ( ) button to exit Image Setup.
You have completed monitor setup.
Page 18
15
DEUTSCH
Adjusting your LCD Monitor
User Controls Accessible Via On Screen Display (OSD)
User control features
• Direct access controls
• Main OSD menu controls
Icon Control Description
Image Setup Activates automatic image adjustment.
Brightness
Directly accesses the Brightness setting on the OSD main menu.
OSD Enter Displays the OSD main menu.
Power Switch Switches the monitor on and off.
Icon Control Description
Exit
Cancel
Exits from menus and sub-menus and cancels sub-menu settings.
Left Arrow
Moves the cursor to highlight icons and other options.
Right Arrow
Moves the cursor to highlight icons and other options.
OSD Enter
OK
Enters menus and sub-menus and selects the highlighted option.
Page 19
16
Operation
The image is already
optimized for many display modes; however, the user controls can be used to adjust the image to your liking.
• Press the OSD Enter button to display the main OSD menu.
• Use the Arrow buttons to move among the icons. Select an icon and press
OSD Enter to access a function. If there is a sub-menu, you can move between options using the Arrow buttons, then press OSD Enter to select a function. Use the Arrow buttons to make adjustments. Press the button to save.
The settings are saved after
adjustment and when exiting the OSD and will be effective thereafter.
• Press the Exit/Cancel ( ) button to move backwards through the sub-
menus, cancel settings, and exit from the OSD.
Page 20
17
DEUTSCH
On-Screen Display (OSD) Controls
The settings can be adjusted with the user controls on the On-Screen Display (OSD). Press the OSD Enter button ( ) to activate the OSD.
The LCD monitor needs
time to become thermally stable the first time you turn it on each day. Thus, to achieve more accurate adjustments for parameters, allow the LCD monitor to warm up (be On) for at least 15 minutes before making any screen adjustments.
Initial appearance of OSD
OSD functions
Brightness/Contrast
Exit OK
OSD Icon on
Main Menu
Submenu Description Controls and Adjustments
Brightness/
Contrast
Brightness
Adjusts brightness.
Contrast
Adjusts contrast.
Image Position
Horizontal Position
Moves the screen left or right.
Vertical Position
Moves the screen up or down.
Page 21
18
Image Setup
Automatic
Activates automatic image adjustment.
Manual
• Clock
• Phase
Use the
or button to adjust the interference. If satisfactory results are
not obtained using the Phase adjustment, use the Clock adjustment and then use Phase again.
Image
Properties
Color
Adjusts intensity of red, green and blue.
1. Preset Mode
• 6500K
• 7200K
• 9300K
6500K makes the screen redder. 7200K adjusts the screen to the default color settings. 9300K makes the screen bluer.
2. Custom
•Red
•Green
•Blue
Increases or decreases 'red'. Increases or decreases 'green'. Increases or decreases 'blue'.
Options
Information
Shows resolution, refresh rate, and product details. Note: This screen does not allow any changes to the settings.
Language
The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.
Select one of the 5 languages (English, French, Italian, German and Spanish) to use for the OSD.
OSD Icon on
Main Menu
Submenu Description Controls and Adjustments
Page 22
19
DEUTSCH
OSD Icon on
Main Menu
(Continued)
Submenu Description Controls and Adjustments
Options
Menu Position
Adjusts menu location on the screen.
1. Default Returns the menu position to the default settings.
2. Custom
• Horizontal
Changes the horizontal position of OSD.
•Vertical
Changes the vertical position of OSD.
Factory Default
Resets monitor to the original settings.
• Cancel
• Reset
Does not make the adjustment. Resets the settings.
Accessibility
Changes button repeat rate and menu time out setting.
• Button repeat
rate
Selects
or button repeating rate. Off - increases by 1 each time the
button is pressed. Default - increases continuously while the button is pressed. Slow - increases by 1 every 2 seconds while the button is pressed.
• Menu time out
Sets the length of time the OSD will remain active after the last time a button is pressed.
Use the
or button to select
the time from 5 to 60 seconds.
Exit / Cancel
Exits from current OSD MENU. / Cancels adjustments and exits sub-menu screens.
Page 23
20
Further Information
Display Modes
Your computer controls the monitor’s display mode. Refer to your computer documentation for details on how to change display modes.
The image size, position and shape might change when the display mode changes. This is normal and the image can be readjusted using
IMAGE SETUP
( ) and the monitor controls.
Unlike CRT monitors, which require a high refresh rate to minimize flicker, TFT technology is inherently flicker-free. If possible, configure your computer for 1024 × 768 addressability at 60Hz vertical refresh rate.
For the display modes listed on the next page, the screen image has been optimized during manufacture.
For image problems, you
may want to run AUTO Setup again before consulting this section. In most cases, AUTO SETUP can fix the problems. See
Image Setup (
)
for DOS
on
Page 12 for details.
Factory Set Display Modes
† Recommended
Note: VESA timings are as detailed in the VESA “Display Monitor Timing Specification”.
Version 1.0, Revision 0.8, dated 09/17/98.
Addressability Refresh Rate Horizontal Frequency
640 × 350 70 Hz 31.5 kHz
640 × 480 75 Hz 37.5 kHz
640 × 480 72 Hz 37.8 kHz
640 × 480 66 Hz 35.0 kHz
640 × 480 60 Hz 31.5 kHz
720 × 400 70 Hz 31.4 kHz
800 × 600 56 Hz 35.1 kHz
800 × 600 60 Hz 37.8 kHz
800 × 600 72 Hz 48.0 kHz
800 × 600 75 Hz 46.8 kHz
832 × 624 75 Hz 49.7 kHz
1024 × 768 60 Hz 48.4 kHz
1024 × 768 70 Hz 56.5 kHz
1024 x 768 75 Hz 60.0 kHz
†
Page 24
21
DEUTSCH
Power Management
If your computer has
previously been used with a CRT monitor and is currently configured to a display mode outside the range that the Flat Panel monitor can display, your monitors failsafe feature will display an image sufficient to allow you to re­configure the computer, preferably to 1024 x 768 at 60Hz.
The power management feature is invoked when the computer recognizes that you have not used your mouse or keyboard for a user-definable period. There are several states as described in the table below.
As an
ENERGY STAR
®
Partner, IBM has determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
For optimal performance, switch off your monitor at the end of each working day, or whenever you expect to leave it unused for long periods during the day.
* There may be a slight delay before the picture reappears.
Product Disposal
The fluorescent lamp in the liquid crystal display contains a small amount of mercury. Dispose of it as required by local ordinances and regulations.
State
Power
Indicator
Screen
Restoring Operation
Compliance
On Steady green Normal
Active Off Blinking green Blank
Press a key or
move the mouse. *
E
NERGY STAR
®
Page 25
22
Troubleshooting
If you have a problem setting up or using your monitor, you might be able to solve it yourself. Before calling your retailer or IBM, try the suggested actions that are appropriate to your problem.
Problem
Possible
Cause
Suggested Action Reference
Computer does not boot after the graphics adapter is installed
There is another graphics adapter in the computer
Remove the other
graphics adapter plugged into one of the expansion slot.
If the card is built-in to
the motherboard, check your system manual for instructions on how to disable the built-in adapter.
Connecting your Monitor
section on page 6
The screen image is garbled or unusable (rolling screen images, overlapping screen images or a blank screen)
The display driver is trying to use a setting your monitor does not support
Select the correct
monitor.
Connecting your Monitor
section on page 6
Screen is blank and power indicator is off
No power to monitor
Ensure that the
electrical outlet and the monitor are both switched on.
Check that the power
cord is firmly plugged into the electrical outlet and the power supply unit.
If the power cord plug
has a removable fuse, replace it.
Try another power
cord.
Try another electrical
outlet.
Connecting your Monitor
section on page 6
Page 26
23
DEUTSCH
Screen is blank and power indicator is steady green
Brightness and Contrast may be too low
Adjust brightness and
contrast.
User Controls Accessible Via On Screen Display (OSD)
section
on page 15
Screen is blank and power indicator is blinking green.
The monitor is in the Power Saving state
Press any key on the
keyboard or move the mouse to restore operation.
Check the Power
Management software on your computer
Power Management
section on page 21
The monitor is not receiving a video signal
Check that the signal
cable is firmly connected to the computer.
Check that no pins are
bent in the signal cable connector.
Connecting your Monitor
section on page 6
The monitor is in the Active Off state
Press any key on the
keyboard or move the mouse to restore operation.
Check the Power
Management software on your computer.
Power Management
section on page 21
Display mode of the computer is outside the range of the monitor
Reconfigure the
computer to use a supported display mode.
Further Information
section on page 20
Image appears to be smeared
There are noises in the video signal
Select Image Setup
menu in the OSD. Then select MANUAL to adjust Phase/Clock settings.
User Controls
section on page 17
Image appears to be discolored
The Color setting may be incorrect
Adjust the Color
settings.
User Controls
section on page 17
Problem
Possible
Cause
Suggested Action Reference
Page 27
24
A few dots are missing, discolored, or inappropriately lighted.
A small number of missing, discolored, or
lighted dots may be present on the screen, which is an intrinsic characteristic of the TFT LCD technology and is not an LCD defect.
Problem
Possible
Cause
Suggested Action Reference
Page 28
25
DEUTSCH
Help and Service Information
If you are unable to correct the problem yourself, you may seek further help as follows:
Call the IBM HelpCenter
®
.
In the US call 1-800-772-2227
In Canada (Toronto Only) call 416-383-3344
In Canada (all others) call 1-800-565-3344
If possible, stay by your
computer. Your Technical Support Representative may wish to go through the problem with you during the call.
In other countries contact your dealer, retailer, or other IBM authorized Servicer.
Before calling, please have available as much of the following information as possible:
More help, late-breaking
news and details of the latest accessories for these products may be found on the worldwide web at:
http://www.pc.ibm.com/us/ accessories
1. Model and serial number from the label on your monitor.
2. Purchase receipt.
3. Description of problem.
4. Computer type and model.
5. System configuration (hardware fitted, etc.).
6. System BIOS version number.
7. Operating System and version number.
8. Display driver version number.
9. Video Adapter Type.
Page 29
26
Specifications
This color monitor (Type-model 6636-xx2) uses a 15-inch TFT LCD
Dimensions Height:
Depth: Width:
370 mm (14.57 in.) 214 mm (8.43 in.)
363.6 mm (14.32 in.)
Weight Unpackaged:
Packaged:
4.202 Kg (8.85 lb)
5.620 Kg (12.379 lb)
Tilt Tilt: – 4° / + 40°
Image Viewable Image Size:
Maximum Height: Maximum Width: Pixel Pitch:
381 mm (15.0 in.) 228 mm (8.98 in.) 304 mm (11.97 in.)
0.297 mm (.010 in.) (H) × 0.297 mm (.010 in.) (V)
Power Input Supply Voltage:
Max Supply Current:
100 - 240 V ac, 50/60 Hz
0.5 A
Power Consumption
Normal Operation: Active off:
< 25 W < 2 W
Video Input Input Signal:
Horiz. Addressability: Vert. Addressability: Clock Frequency:
Analog Direct Drive, 75 ohm 0.7 V 1024 pixels (max) 768 lines (max) 80 MHz
Communications VESA DDC: 2 B
Supported Display Modes
VESA Standard modes between Horiz. Frequency: Vert. Frequency:
IBM, VESA, HP, Sun, Mac 30 kHz - 61 kHz 56 Hz - 75 Hz
Environment Temperature:
Operating: Storage: Shipping:
Humidity:
Operating: Storage: Shipping:
10 to 35° C (5 to 95° F)
- 20 to 60° C (-4 to 140° F)
- 20 to 60° C (-4 to 140° F)
10 to 80% 5 to 95% 5 to 95%
Power consumption figures are for the monitor and the
power supply combined.
Page 30
27
DEUTSCH
Service Information
The following parts are for use by IBM service or IBM authorized dealers to support the customer warranty. Parts are for service use only.
Model Type 6636-XX2
31P9960 6636-AB2 Monitor - Stealth Black 31P9963 6636-AB2 Stand - Stealth Black 31P9965 6636-AB2 Analog Video Cable
Page 31
28
Notices and Trademarks
This section contains information on notices and trademarks.
Notices
IBM may not offer the products, services, or features discussed in this document in all
countries. Consult your local IBM representative for information on the products and services
currently available in your area. Any reference to an IBM product, program, or service is not
intended to state or imply that only that IBM product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe any IBM intellectual
property right may be used instead. However, it is the user’s responsibility to evaluate and
verify the operation of any non-IBM product, program, or service.
IBM may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not give you any license to these patents. You
can send license inquiries, in writing, to:
IBM Director of Licensing
IBM Corporation
North Castle Drive
Armonk, NY 10504-1785
U.S.A.
The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES
CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied
warranties in certain transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors. Changes are
periodically made to the information herein; these changes will be incorporated in new editions
of the publication. IBM may make improvements and/or changes in the product(s) and/or the
program(s) described in this publication at any time without notice.
IBM may use or distribute any of the information you supply in any way it believes appropriate
without incurring any obligation to you.
Any references in this publication to non-IBM Web sites are provided for convenience only and
do not in any manner serve as an endorsement of those Web sites. The materials at those
Web sites are not part of the materials for this IBM product, and use of those Web sites is at
your own risk.
Page 32
29
DEUTSCH
Trademarks
The following terms, used in this publication, are trademarks or service marks of the IBM Corporation in the United States, other countries, or both:
IBM Logo
ThinkVision
HelpCenter IBM
E
NERGY STAR
®
and the ENERGY STAR® logo are U.S. Govt. registered
trademarks.
Microsoft
®
Windows®, and Windows NT are trademarks of Microsoft
Corporation in the United States, other countries, or both.
Other company, product, and service names may be trademarks or service marks of others.
© Copyright International Business Machines Corporation 2003. All rights reserved.
Page 33
30
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use