Precautions
Precautions
Display port Cable
DVI
HDMI Cable 1.4
HDMI Cable 2.0
HDMI2(MHL)
HDMI1
DP Cable
Display Port
Headphone out
Adapter Jack
Dual link DVI Cable
1. Press the “MENU” button to bring up the screen.
2. Press the " , " buttons to select the main option.
3. Press the " " button after selecting the main option.
4. Bring up the sub-menu. Use the " , " buttons to select the desired option.
5. Press the " " button after selecting the desired sub-menu option.
6. Use the " , " buttons to adjust the set value.
7. Pressing the " " button Three times saves and exits the setting mode.
* Pressing the " " button moves back to the previous menu.
MENU
Button Function description
Hot key setting
State lamp
Opens OSD Menu window.
Decreases value of chosen icon.
Increases value of chosen icon.
Indicates monitor's state.
On Mode : Blue
Standby Mode : Blue & RED
Soft Power Off : LED Off
No signal Message : RED
Volume(Option)
Mute(Option)
Chooses Sub icons of the Menu.
Moves left icon choice bar.
Moves Right icon choice bar.
Exits from icons of the Menu.
Source Information
Changes Input Signal.
Turns On/off Monitor.
Defalult : Auto
Picture
Color
Advance
Input
Other
Information
Main Menu
ICON
Main Menu SUB Menu Function
Backlight Adjusts the Backlight of the screen.
Brightness Adjusts the Brightness of the screen.
Contrast Adjusts the Contrast of the screen.
Shapness Adjusts the Sharpness of outlines.
Gamma Adjusts the accuracy of image .
Temperature Selects Warm or Cool colors suitable for video type.
Aspect Ratio Selects the screen ratio. ( Full , 16:9 , 4:3 , 5:4 , 1:1 )
User setting values returns to factory setting values.
Adjusts OSD display time on the screen.
Adjusts OSD screen left or right.
Adjusts OSD screen upwards or downwards.
Selects OSD language.(2 language)
Adjusts transparency of the OSD window.
Adjusts rotation of the OSD window. ( 0 , 90 , 270 )
Over Scan Selects the screen size. ( Used in case of DTV timing. )
Selects the input signal. ( Normal : Auto Select )
DP / HDMI 1 : 3840 2160@60Hz
HDMI2 / DVI : 3840 2160@30Hz
Over Drvie Adjusts response time of Panel.
DP Option
Auto Select
DP
HDMI 1
MHL(HDMI 2)
DVI
Reset
Menu Time
OSD H Position
OSD V Position
Signal : ( D0 : DP )
Displays the information of present signal.
Resolution : ( 3840 2160@60Hz )
Frequency : ( H : 133.5Khz PCLK : 533.5Mhz )
Language
Transparency
Rotate
Selects the version of DP signal.( Normal : 1.2 )
Color Effect Chooses optimum color condition by type of videos.
Demo Unsupported.
Color format Controls the Color format of the color. ( RGB or YUV )
PCM To compensate the image qulity.
Hue Adjusts the proportions of green and red.
Saturation Adjusts the Density of color.
Resolution
Power Consumption LED ColorState
Horizontal Frequency Vertical Frequency
300
12 ms
31 ~ 133.5KHz
56 ~ 75Hz
DVI , HDMI 1(60Hz) , HDMI 2(30Hz) , Disply port(60Hz)
29pin DVI, 19Pin HDMI, 20Pin Display port
45W (Max), 32W (Typ)
0.5W
596.16mm(H) x 335.34mm(V)
155.25um(H) x 155.25um(V)
3840 x 2160@60Hz
178º / 178º (H/V)
1.07 Billion
AC : 110V~240V 50/60Hz 1.5A , DC : 24Vdc, 5A
Yes(Option) , Headphone out(Option)
FCC compliance
-
FCC ID: PJIP278DPL
ote: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for h elp.
Change or modifications not expressly approved by the
party responsible for compliance could void the user’s authori ty
to operate the equipment under FCC rules.
Loading...