Hyundai LT32DW002 Users Manual

FCC ID : PJILT32DW002

ATTACHMENT E.

- USER’S MANUAL -

HYUNDAI CALIBRATION & CERTIFICATION TECHNOLOGIES CO., LTD.

SAN 136-1, AMI-RI, BUBAL-EUP, ICHEON-SI, KYOUNGKI-DO, 467-701, KOREA

TEL:[phone]	FAX:[phone]	www.hct.co.kr
Report No. : HCT-F06-0403		1/1

FCC Information

User Instructions

The Federal Communications Commission Radio Frequency Interference Statement includes thefollowing warning :

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital devicepursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses, and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particularinstallation.

If this equipment does cause harmful interference to radio or television receptions, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures :

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.

•Consult the dealer or an experienced radio/TV technician for assistance.

User Information

Changes or modifications not expressly approved by the party responsible for compliance could voidthe user’s authority to operate the equipment.Connecting of peripherals requires the use of grounded shielded signal cables.

HYUNDAI LCD TV

Important Tip

Image Retention Effect (Image Sticking)
1.	Cause :
-	Image Retention Effect may come from displaying a still picture in certain period of time with at a
	certain area continuously, as the feature of LCD panel. This is caused due to brightness degradation.
	Many LCD manufacturers are trying to overcome this limitation.
2.	Prevention

- To avoid this matter, use the product after reducing brightness and contrast, especially when a still image is displaying for a long time. (Contrast 50/Brightness 50 - See 32 page)

Once image retention occurs, use the mode that displays more motion pictures. It will help reduce this matter.

3. Solution

-The temporary image sticking would decrease with displaying Full-White pattern during 10 hours.

*The permanent image sticking could not take off under the latest technology.

This method may be used to eliminate a temporary retained image that occurs after displaying a still image for a certain period of time. Since it may take several minutes to several hours to remove image sticking, it is recommendable to display motion pictures during 2~3 minutes every hour when keeping displaying a still image. As image sticking is influenced by the brightness of a still image being displayed and its display time, it is recommended that you reduce the brightness of the screen when displaying a still image for a long time.

* Image Sticking does not come under the warranty.

Image Sticking Precaution

When watching a still Image within motion pictures and Panorama/Wide/4:3 screen

Panorama, Wide, 4:3 screen

Box still image

1. Note :

-When the central area of the screen and the screen edges are fixed, the different brightness level of the edges may cause image retention on the edges when watching for a long time

-This phenomenon is the same matter to other LCD manufacturers. Please do not watch a still image for a long time.

-If you watch a still image for a long time, this may damage your TV.

* This matter does not come under the warranty.

HYUNDAI LCD TV

Features

Integrated HDTV

An HDTV has a built-in ATSC digital tuner.

It does not need a separate set-top box to receive over the-air DTV signal.

Dual Scan/Multi-Viewing

You can program analog TV broadcasting and digital TV broadcasting automatically at the same time for multi-viewing.

A Wide Array of Screen Settings

You can choose different screen settings depending on the type of program you are watching or the surrounding conditions (the outside weather conditions). You can switch among Standard, and Mild options or you can configure the screen settings for yourself.

A Wide Array of Sound Settings

You can choose an optimal sound setting for the type of program you are watching.

You can switch among custuom Standard, movies, Music, and Speech options or you can configure the sound settings for yourself.

Favorite Channel Memory

You can memorize the channels you are watching frequently.

SRS TrueSurround XT

You can enjoy dynamic and surround sound with ordinary speakers.

Dolby-Digital

When receiving digital broadcast signal, you can enjoy dynamic and surround sound with two ordinary speakers just like Dolby 5.1.

A Variety of Aspect Ratios

You can adjust the screen size at your preference.

Auto On/Off Function

This function allows you to turn on or off your TV at the preset time.

Game Prevention Function

This function is designed to prevent a VCR or game player from being connected to the TV.

Table of Contents

General Information
Safety Precaution ................................................................	5
Contents of the Package .......................................................	9
Products Sold Separately ......................................................	9
Kensington Lock Anti-theft Device ......................................	10
How to Mount and Detach The Speakers ...........................	11
How to adjust the view angle ..............................................	12
Parts Names and Functions ................................................	13
Remote Control ...................................................................	17
Connections
How to Watch Both Analog and Digital Broadcasts
with a Single Antenna .........................................................	19
How to Watch Both Analog and Digital Broadcasts
with Two Antennas .............................................................	20
Before Connecting the Video/Audio Connections to
External Devices... .............................................................21
How to Connect a VCR/Cable Receiver ................................	22
How to Connect a DTV Receiver or DVD Player ....................	23
How to Connect a Camcorder/Game Player .........................	24
How to Connect to a PC ......................................................	25
HDMI Connection ................................................................	27
How to Connect an External Visual Device ...........................	29
How to Use Digital Sound ....................................................	30
Picture Setup
How to Select the Picture Mode ..........................................	31
How to Set the Desired Picture ...........................................	32
How to Adjust the Color Temperature of the Screen ............	33
How to Select the Aspect Ratio ...........................................	34
How to Watch the PIP .........................................................	36
How to Set the INPUT for the Sub-Picture ...........................	37
How to Reduce Noise ..........................................................	39
Sound Setup
How to Select the Audio Mode ............................................	40
How to Adjust the Desired Audio Mode ..............................	41
How to Use the Automatic Volume Control ..........................	42

HYUNDAI LCD TV

How to Select MTS(Multi-Channel Sound) ...........................	43
How to Listen to SRS TruSurround XT (Surround) ................	44
How to Set the Output of Subwoofer ...................................	45
How to Set the Audio Output ...............................................	46
How to Set the Digital Audio Output ....................................	47
How to Set Audio Language ................................................	48
Channel Setup
How to Store Channels Automatically ..................................	49
How to Add/Erase Channels Manually .................................	50
How to Set Favorite Channels .............................................	51
How to Fine Tune Channel Reception ..................................	52
How to the LNA (Low-Noise-Amplifier) Feature ...................	53
Function Setup
How to Choose Your Language ...........................................	54
How to Set Clock, On/Off Time, Sleep Time ........................	55
How to Set the Geometry in PC Mode ..................................	57
How to Set Key Lock ...........................................................	58
How To Set Block Program .................................................	60
How to View Closed Captions ..............................................	62
DTV Setup
How to Use the Current Channel Guide ..............................	64
How to Reserve TV Programs Using the Total Channel Guide ....	64
How to Use TV Program Reservation ...................................	65
How to Check or Cancel a Scheduled TV Program ...............	66
How to Use Memory Mode ...............................	67
Appendix
How to Use an External Device Using the Remote Control ...	75
Glossary .............................................................................	78
Troubleshooting ..................................................................	81
Care and Cleaning ..............................................................	83
Product Specifications ........................................................	84

GENERAL INFORMATION

Safety Precaution

The contents of this section are provided for the safety of users and their property. Please read the instructions carefully before using.

Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No.70-1984, provides information about proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Example of Grounding According to National Electrical Code Instruction

Do not connect multiple electrical appliances to a single outlet.

-It may cause a fire due to overheating from the outlet.

Make sure to remove the speakers before moving the TV with speakers mounted on it.

- When the speakers are detached from the unit while carrying it, this may cause damage to the unit or personal injury.

Do not use or store a flammable spray or inflammable things near the TV.

- They may cause explosion or fire.

Do not install the TV in a bookshelf, closet, or a place where there is poor air circulation.

-Fire may be caused due to the rise of internal temperature.

Any necessary action such as making the antenna cable loop at the entrance of the building should be taken to prevent rainwater on the outdoor antenna cable from possibly running into the indoor.

-If raindrop gets into the LCD TV, it may cause a fire or an electric shock.

5

HYUNDAI LCD TV

If there is a persistent accumulation	Do not use a damaged power cord
of dusts or water on the plug, please	or plug, or loose outlet.
make sure to wipe it off using a dry	- It may cause electric shock or fire.
cloth.
- It may cause a fire or an electric shock.

Firmly plug in the power cord so that it does not pull out.

- An unstable connection may cause fire.

Do not install in a place where there is oil, smoke, excessive humidity, or where water may be sprinkled on it.

- This may cause electric shock or fire.

Do not put a water bowl, vase, candle, bug repellant smoke, cigarette, plants, or heavy thing on the TV.

- It may cause electric shock or fire and also heavy things may cause injury when they fall.

Do not install on an unstable place or small support.

-This may cause the TV to fall, resulting in serious injury to a child or adult.

Never attempt to open, fix, or modify your TV.

-When there is a need for fixing, call a service center. Fire or electric shock may be caused.

When the TV produces abnormal noise, burning smell, or smoke, unplug the TV immediately and call a service center.

- Electric shock or fire may be caused.

Do not put a metallic object like chopstick, wire, or puncher or inflammables like paper or a match in a vent, headphone jack, or AV jacks of the TV.

- Electric shock or fire may be caused.

INFORMATION GENERAL

6

GENERAL INFORMATION

Safety Precaution ......................................

Continued from previous page

The contents of this section are provided for the safety of users and their property.

Please read the instructions carefully before using.

Do not block ventilating slits with a table cloth.

- Blocking the ventilation slits may produce inner heat increase, resulting in a fire.

	Keep the TV at least 10cm away from the	Do not place any heat sources such as
		radiators and heat registers, etc. near the TV.
	wall for ventilation.
		- It may cause a fire.
	- Fire may be caused due to the rise of inner
	temperature.
		Do not place toys and cookies, etc. on the TV,
		which may attract children’s attention.
		- If it falls over on children, it may cause serious
		injury.

Do not allow children to climb or play on the TV.

-If it falls over on children, it may cause serious injury.

When cleaning the TV, make sure to disconnect the power plug and use a dry, soft cloth for a cleanup.

-Please avoid using chemicals such as wax, benzene, alcohol, thinner, mosquito spray, air freshener, lubricant or synthetic detergent.

Unplug when you do not use your TV for a long time.

-If dust is stacked on the TV, electric shock or fire may be caused from heat, fire, or deterioration of insulation.

Consult a service center or customer service for inside cleaning about once a year.

- When dust is piled inside the TV for long time, fire or malfunction may be caused.

When moving the TV, two or more people are advised to carry it.

- Injury or damage may be caused when the TV falls.

7

HYUNDAI LCD TV

Unplug the product during lightning or thunderstorms and never touch the antenna cable.

- It may cause a fire or an electric shock.

	Keep the remote control batteries out of
Do not install the product on the floor.	sight and out reach of children.
- If it falls over, your child may be injured.	- If your child swallows a battery, see your
	doctor immediately.

When replacing batteries, make sure to match the batteries to the (+) and (-) marks in the battery compartment.

- Mismatching of polarities may result in internal damage to batteries, fire due to leakage or contamination.

			In the event of damaging or dropping the
		Always use the standard batteries and avoid	product, switch off the power and remove
			the plug.
		using old batteries together with new ones.
			- Using a damaged product may cause an
		- Otherwise it may result in internal damage
			electric shock or a fire.
		to batteries, fire due to leakage or
			- Contact your local service center.
		contamination.

INFORMATION GENERAL

Before moving the product, ensure to switch off the power and unplug all the electrical cords and the external connection cords such as an antenna cable and other source connections, etc.

-An electrical cord(s) may be damaged, resulting in a fire or an electrical shock.

Ensure the power cord doesn’t trail across any hot objects like a heater.

- This may cause a fire or an electric shock.

Consult a service center or customer service for inside cleaning about once a year.

-When dust is piled inside the PDP for long time, fire or malfunction may be caused.

8

GENERAL INFORMATION

Contents of the Package

hen opening the package, please ensure to check the following accessories provided.

	Antenna Cable	Power Cord
	(coaxial cable)

Remote Control & 2 batteries	User's Guide
(1.5V AAA)

Products Sold Separately

If you want to purchase separately sold products, consult a service center, electronics shops, or parts seller.

Hdmi cable	S-video Cable

Wall Mounting Support

Component Cable	Composite Cable
(Y, Pb, Pr)	(Video/Audio)

Audio Cable (DIV/DVD)

Audio Cable (PC)

PC signal Cable (D-SUB)

9

HYUNDAI LCD TV

Parts Names and Functions - For Q40* Model only

Front View

INFORMATION GENERAL

* This product image may be a bit different from the actual product.

Speaker

Power switch

Use this switch to turn on/off power.

Remote sensor and power LED.

-Point the remote control toward here.

-It displays standby or operation status.

-Power Indicator Status -

Indicator	Status
Red	Standby
Green	Power on

Power button

Use this button to turn on or off the TV.

Source button

Use this button to switch among inputs connected to the TV.

Menu button

Use this button to display or exit from menus.

Select button

Use this button to select each item of menu.

Channel buttons

Use these buttons to change channels. These buttons also serve as the cursor of Down and Up buttons when in Menu mode.

Volume buttons

Use these buttons for your desired sound level. These buttons also serve as the cursor of Select/Adjust when in Menu mode.

10

GENERAL INFORMATION

Rear View

* This product image may be a bit different from the actual product.

Power Switch

use this switch to tum on/off power

Power(AC) Input terminal Connect the power cord to this

terminal.

RS-232 input terminal

Connect to the RS-232 terminal of a PC to check its service.

S/P DiF optical digital audio output terminal

D-SUB input terminal

D-SUB Audio input terminal

Component 1 Video input terminal

Component 1 Audio input terminal

Component 2 Video input terminal

Component 2 Audio input terminal

Video input terminal

S-Video input terminal

S-Video/Video Audio input terminal

Antenna (Analog/DTV) input terminal

11

HYUNDAI LCD TV

Rear View

* This product image may be a bit different from the actual product.

Power Switch

use this switch to tum on/off power

Power(AC) Input terminal Connect the power cord to this

terminal.

RS-232 input terminal

Connect to the RS-232 terminal of a PC to check its service.

S/P DiF optical digital audio output terminal

D-SUB input terminal

D-SUB Audio input terminal

Component 1 Video input terminal

Component 1 Audio input terminal

Component 2 Video input terminal

Component 2 Audio input terminal

Video input terminal

S-Video input terminal

S-Video/Video Audio input terminal

Antenna (Analog/DTV) input terminal

INFORMATION GENERAL

12

Remote Control

GENERAL INFORMATION

1.POWER/STANDBY

2.POWER LED

3.MAGIC

4.ASPECT

5.CAPTION

6.ADD/ERASE

Use this button to add or erase channels. 7. INFOMATION

Use this button to display resolution or various program

8.PICTURE

9.SOUND

10.SRS

Use this button to select 3D surround sound.

11.SAP

12.EXIT

13.MENU SELECTION

Use this button to select menu item

14. LEFT/RIGHT MOVE/ADJUST

Use these buttons to move between menu items or to adjust each item.

15.SOURCE

16.TILT

17.PIP

-ON/OFF

-SIZE

:Use this button to select the size of sub-picture.

-SIZE

:Use this button to select the size of sub-picture.

-POSITION

:Use this button to select the position of sub-picture.

-SWAP

:Use this button to swap main and sub-picture.

13

18.EPG

19.MENU

Use this button to call the OSD to the screen.

20.NUMERIC KEYS

21.SERVICE

22.FAV

23.SELLP

24.FREEZE

HYUNDAI LCD TV

INFORMATION GENERAL

How to Insert Batteries in Remote Control

Press and hold ∆ part and push	Insert batteries with proper	Use the remote control with cover
to open cover.	polarities of +and -.	closed.
* Battery type :1.5V/AAA

14

CONNECTIONS

How to Watch Both Analog and Digital Broadcasts with a Single Antenna

You can watch both analog and digital broadcasts by connecting a single antenna.

Connection Method

Make sure that the antenna cable is connected to ANT (ATV/DTV).

-Antenna or Cable service without a cable box connections

-For optimum picture quality, adjust antenna direction if need,

-When inserting a 75 ohm coaxial cable into the input connection, ensure the wire tip not to bend.

-If you experience poor signal reception, we recommend you purchase a signal amplifier for better picture quality.

How to Watch

1	Turn on TV to activate Auto Channel (See page 49) to memorize the available channels.
2	Press SOURCE		INPUT on remote control.
3	Press	OK	to move to Analog TV or Digital TV and press		OK	to select.
4				CH-
	Press		button or	button to select the desired channels.
	Ex.) When you want to watch cable channel number 120, press					+100 + 2 + 0
	the digit buttons.

15

HYUNDAI LCD TV

Before Connecting the Video/Audio Connections to External Devices...

Please make sure to read the following information on connection to enjoy best picture quality.

Video/Audio connectors

Types of video/audio cable :

HDMI 15-Pin D-Sub COMPONENT S-VIDEO COMPOSITE

Best picture quality is displayed in the following order.

The superior picture quality starts from the far left side.

CONNECTIONS

-When connecting an external device, ensure to read the connecting device’s manual. The location or the number of the terminals on the external device may be different depending on its model.

-Connect a HDMI (or DVI) connection to the output of DVD, cable receiver or satellite receiver. Connecting a HDMI (or DVI) connection to a PC may result in a message, “Unknown Signal”.

-Do not power on until all necessary connections are made. If power is given before connections completed, this may damage the product.

-Make sure to match the cable in color with the terminal.

-Make sure to check the type of terminals to be connected.

16

CONNECTIONS

How to Connect a VCR/Cable Receiver

Connection Method

1	Connect the Video cable or S-Video cable between Video/S-Video output terminal of VCR or Cable receiver and
	Video/S-Video input terminal of TV. (Connect the jacks to terminals in the same color.)
2	Connect the Audio cable (Left: white, Right: red) between Audio output terminal of VCR or cable receiver and
	Audio input terminal of TV. (Connect the jacks to terminals in the same color.)

Video/Cable receiver

S-Video Cable

Audio cable

Video cable

How to Watch

1				SOURCE
	Turn on TV to press			on remote control.
2	Press	OK	to move to Video or S-Video and press OK to select.

For more information, read the user’s guide of VCR or cable receiver.

To enjoy better picture quality, use the S-Video cable rather than the composite cable.

17

HYUNDAI LCD TV

How to Connect a DTV Receiver or DVD Player

Connection Method

1	Connect the Video cable (Y, Pb, Pr) between output terminals (Y, Pb, Pr) of DTV receiver or DVD player and the
	input terminals (Y, Pb, Pr) of DTV/DVD (480i/480p/720p/1080i) on the rear of TV.
	(Connect the jacks to terminal in the same color.)
2	Connect the Audio cable between Audio output terminal of DTV receiver or DVD player and Audio input
	terminal for DTV/DVD Audio on the rear of TV. (Connect the jacks to terminals in the same color.)

DTV receiver / DVD Player

CONNECTIONS

Video (Y, Pb, Pr) cable

Audio cable

How to Watch

1				SOURCE
	Turn on TV and press			on remote control.
2	Press	OK	to move Component 1 or Component 2 and press		OK	to select.

For more information, read the user’s guide of DTV receiver or DVD player.

-Output terminal mark (Y, Pb, and Pr) of DVD player may be indicated as Y, B-Y, R-Y/Y-Cb-Cr /Y-Pb-Pr according to the type of DVD player models.

-If your DVD player or Set Top Box supports HDMI (or DVI) /D-SUB, see Connecting to a PC (page 25) for connection. You can enjoy more clear picture quality.

18