HYUNDAI H-LED22V14 User Manual [ru]

H-LED22V14

LED TV

ЦВЕТНОГО ИЗОБРАЖЕНИЯ

ТЕЛЕВИЗОР

ЖИДКОКРИСТАЛЛИЧЕСКИЙ

(LCD)

Руководство по эксплуатации Instruction manual

Table of contents

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start

Utilization of the product Important safeguards Installation

Wall mounting Stand installation

Connection

Outdoor antenna connection Other connections

Operation

Control elements

Front panel

Back panel Remote controller

Changing the battery

General operations

Power

Operations

Teletext operations OSD operation

Channel setting Picture setting Sound setting Timer setting

Option setting USB operation

Background information Operatoins of file playback

General information

Troubleshooting

Causes of interference Accessories Specifications

2 3 3 3 4 4 4 5 5 5 5 6 6 6 6 7 7 8 8 8 8 9 9

9 10 10 10 11 11 11 12 12 12 13 13

Before you start

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Please unplug the power cord from the AC outlet and contact a service center for repair if following occurs: any obvious abnormality appears in the unit, such as smoky, peculiar smell or strange sound; liquid has been spilled or other objects have fallen into the unit; no picture or sound; cover or panel is broken; although you have operated the unit following the operating instructions, it still cannot work normally.

• This unit can be connected to a power supply outlet without the third ground contact as well as with a ground contact.

• Always disconnect the power cord and antenna during a storm.

• Do not fix the power cord with a metal nail.

• Unplug the power cord from the AC outlet; also unplug the signal cables from the input ports when the unit is unused for long periods of time.

• When unplugging the plug, always hold the wide slot, do not touch the metal part, and do not destroy, refit, twist, pull or roast the power cord.

• Please contact the service center immediately if you found that the core is showed in the air or has been broken.

• Please replace the AC outlet if the metal bolt cannot be inserted into the power socket completely or it cannot be fastened even when it was pushed in, otherwise, any accidents of

shocks and fires would happen.

• Never touch the antenna lie or power plug

if it stars to thunder.

• Do not touch the power plug with wet

hands.

• Do not use any non-rated power socket with numerous devices jointed on one power socket or cable device. The wire of nondesignated capacity may cause the fire due to the generation of heat.

• All instructions must be read and understood well before you operate the unit. Heed all warnings and follow all instructions.

• Please use the accessories provided by the manufacturer. Using inadequate accessories may result in accidents.

• Please adjust the product through the panel buttons or the remote controller, do not remove the cover or attempt to service the product by yourself. Do not disassemble back cover and do not make maintenance by yourself to avoid the electric shock.

• Over-press the panel may destroy the product.

• Do not place the product on an unstable cart, stand surface, tripod, bracket, or table. The product may fall, causing serious accidents as well as the damage to the product.

• Please place the product on a flat surface in a well-ventilated location. Keep it away from the burning-light, direct sunlight, vibration, high-temperature and humidity.

• Do not place any vase, potted plant, cup,

Before you start

medicine and any container with water on this product. If the liquid is spilt, it may cause the fire, electric shock or breakdown.

• Do not install it at the place on the strong magnetic field or current field. It may cause break down. This equipment may be observed deterioration of the picture by electromagnetic radiation in electromagnetic environment.

• Fasten the wheel of the product or shelf with wheels when installing this product. If it moves or is tipped over, it may be damaged.

• Do not place any fire source such as candlelight close to this product or place it on this product. If it is tipped over or fallen down, it may cause damage or fire.

• Do not place the unit into closed space of TV for better ventilation; it can reduce the product lifetime. Keep a space at least 10 cm at above, left and right of the TV.

• Please place all the signal cords behind of rear panel.

• Do not overexert or touch the panel when you convey the product. Do not transfer the LED TV up or down display direction.

• Do not transport it with the power cord or the connection cable connected. If you move this product with the power cord or the connection cable connected, the damaged power cord, connection cable or connection terminal may cause the fire, the electric shock or breakdown.

• 2 persons or more shall transport the device, which is heavier than 18 kg. If you drop or tip over the device, it can be damaged.

• The temperature of the product’s body becomes a little higher after a long period use. This phenomenon indicates that heat exchange in normal working mode, thus please do not let children or anyone who is sensitive of temperature to touch.

All images provided herein are schematic

drawings and may differ from of real objects.

Installation

Wall mounting

For wall mounting the back panel of this unit is equipped with 4 screw holes (4 mm diameter, 75 mm horizontal and vertical spread distance). A wall-mount bracket should be used for wall mounting (the bracket is not included and should be acquired separately). Manufacturer is not responsible for improper mounting resulting in damage of the unit.

Stand installation

Place the LED TV on a solid flat surface. Use soft material to place over the front screen to avoid any damage. Then put the slits of the stand onto the fixing elements in the lower part of the unit and fix the two parts by four supplied screws as shown below:

Small screw

Big screw

Connection

Antenna cable connector

75 Ohm co-axis cable

Outdoor Antenna Connection

Use 75Ω coaxial cable plug or 300-75Ω impedance converter to plug in antenna input terminal on the rear of the cabinet.

Other connections

• Connect a TV or CATV antenna to the

antenna jack.

• Connect a video source to the Composite

video input jack with RCA cable.

• Connect an audio source to the proper

Audio input jacks (left and right).

• When using the unit as a computer screen, connect the PC to the PC jack of the unit by the relevant cable.

• Connect PC audio input to PC main unit with related audio cable in PC mode.

TVRF antenna jack

• If the video source has a HDMI output jack, you can connect the signal to the unit by HDMI cable (not included).

• Component input YUV is intended to receive component video signal from the external device. Connection is made with the help of supplied YUV connection cable. To receive audio signal for component video, please use Left and Right audio inputs of this unit.

• Connect your headphones or earphones (not included) to the headphone socket of this unit. When earphones are connected, the sound output through the built-in speakers of this unit is mute.

Operation

Control elements

Front panel

1 2

Back panel

4 5

6 7 8 9 10 11 12

1. Remote control sensor

2. Power indicator

1. CH+/CH- buttons

2. VOL+/VOL- button

3. MENU button

4. SOURCE button

5. POWER button

6. HDMI input

7. Power cord

8. PC (VGA) input

9. PC audio input

10. Composite video input

11. Stereo audio input

12. Component video input YPbPr

13. Headphone output

14. Antenna input

15. USB port

Operation

Remote controller (RC)

8 9

12 13

11. Red button/

button

12. TEXT ( )/ button

13. HOLD ( )/ STILL button

14. INFO/INDEX ( ) button

button

15.

16. AUDIO ( ) button

17. RECALL (

) button

18. EXIT button

19. CH+/CH- buttons

20. CANCEL (

) button

21. button

22. Yellow button/

23. Blue button/

24. E/W button

25. SUBPAGE ( ) button

button

Changing the battery

1. Remove the battery compartment cover on the back of the RC.

20 21 22 23

2. Insert the batteries into the battery compartment making sure that the correct polarity is observed.

3. Install the cover back.

1. POWER button

2. Number buttons

3. SOURCE/REVEAL (

4. SIZE (

)/ZOOM ( ) button

) button

5. MENU button

6. ENTER button/cursor buttons (LEFT/RIGHT/ UP/DOWN)

7. VOL+/VOL- buttons

8. SLEEP button

9. REPEAT button

10. Green button/

button

1 2 3

• Use two AAA batteries for the RC. The RC should be pointed at remote sensor within 8 meters and within 30 degrees at the left or the right side.

• Take the battery out of the RC if it is not used for a long time.

• Do not mix new and used batteries or different types of batteries. Weak batteries can leak and severely damage the RC.

• Do not expose the RC to shock, liquids, and do not place it in an area with high humidity.

Operation

General operations

Power

• Connect the plug of the power cord to the power supply outlet, the power indicator will flash for a while in red showing that the unit is in standby mode. To switch on the unit, press POWER button on the panel or on the RC; the indicator will light in green. Press POWER button again to switch the unit to the standby mode. To switch off the unit completely, disconnect the power cord plug from the power supply outlet.

• Do not leave your TV in standby mode for a long period of time; if you are not going to use the unit, disconnect it from power supply.

• In TV mode the unit will automatically go to standby mode if no signal for 5 minutes. In PC mode the unit will automatically go to standby mode if no signal for 30 seconds.

Operations

• Press VOL- button repeatedly to decrease the volume; press VOL+ button repeatedly to increase the volume.

• Press again or increase volume to resume sound.

• Press SLEEP button repeatedly to set the sleep time (up to 240 minutes). When sleep time is set, press this button to display the time remaining until the auto turn off.

• Press AUDIO ( ) button in TV mode repeatedly to switch between Stereo, Mono, Dual I, Dual I+II and Dual II sound modes (can be unavailable for some channels).

• Press repeatedly SOURCE button on the unit or on the RC, then press UP/DOWN cursor buttons to cycle through the available source list as follows: TV - Component - PC - HDMI USB - AV.

• Select the TV function mode. Press CH-/CH+ buttons to select previous or next channels; or press number buttons to enter a channel number from 1 to 235 directly.

• Press RECALL ( to select from the present channel and the

to mute sound, press this button

) button on the RC

previously displayed channel.

• Press channel list in TV mode (you should setup your favourite channels in Program Edit menu).

• Press INFO button to display the preset TV channel play information.

• Press ZOOM ( select an aspect ratio: 4:3/14:9/16:9/Zoom1/ Zoom2. The set of available aspects can vary depending on the current signal source.

button to display the Favourite

) button repeatedly to

Teletext operations (option)

Select a TV channel in order to pick up the picture signal of Teletext. Teletext button functions are as follows:

TEXT ( TEXT mode. Press this button again to enter mixed mode. Press the button again to return to the channel you are watching.

HOLD ( move to the next page. Press this button again to cancel operation.

INDEX ( index page.

SIZE ( top part of the page. Press this button again to enlarge the bottom part of the page. Press this button third time to normal size text page view.

REVEAL ( cancelled information. Press this button again to cancel the information.

SUBPAGE ( sub-page. Input the number of sub-page and use numeric buttons in the format 0001 for sub page 1. The teletext will search for the sub page. Press SUBPAGE button again to exit the subpage mode.

CANCEL ( the teletext; press again to show the teletext.

E/W: Press this button to switch between available teletext languages.

Red/Green/Yellow/Blue buttons: Press these 4 color buttons to access directly to corresponding color page displayed at the lower parts of teletext screen.

): Press this button to enter into

): Press this button to stop the

): Press this button to go to the

): Press this button to enlarge the

): Press this button to reveal the

): Press this button to select

): Press this button to cancel

Operation

OSD operation

1. Press MENU button to enter the setting

menu displayed on the screen.

2. Press LEFT/RIGHT cursor buttons on the RC or VOL+/- buttons on the panel to select setting page; press ENTER button on the RC or SOURCE button on the panel to confirm.

3. Press UP/DOWN cursor buttons on the RC or CH+/- buttons on the panel to select a parameter to adjust.

4. Press cursor buttons on the RC or VOL+/or CH+/- buttons on the panel to adjust the selected parameter.

5. Press MENU button to return to the previous menu page. Press EXIT button on the RC to quit the menu.

Some menu items may be in grey color, in this case they are not adjustable. Pictures of OSD menu are for reference only; they may differ from the real screens.

Channel setting

CHANNEL

Auto Tuning Color system Sound system Manual Tuning Programme Edit

• Program Edit: this item allows you to sort

TV programs according to your preferences. Enter into program edit menu:

Delete: Select the channel you want to delete.

Press red button to delete the channel.

Rename: Highlight the needed channel. Press green button; then press UP/DOWN buttons to select a symbol. Press LEFT/RIGHT buttons to select previous or next symbol. Press green button to confirm.

Move: Highlight the needed channel. Press yellow button; select the position to put the channel into. Press yellow button to confirm.

Skip: Highlight the needed channel. Press blue button; now this channel will be skipped when you select previous/next channels.

Favorite: Select the channel you want to edit. If this channel is your favorite channel, you can add the mark to the channel as your favorite channel by pressing button.

Picture setting

PICTURE

Picture mode Color temp Aspect ratio DNR Screen

Select Press “ENTER” to select Press “MENU” to return

• Auto tuning: press ENTER button to start

automatic search and saving of available TV channels.

• Color system: PAL/SECAM/NTSC/Auto.

• Sound system: select BG/DK/I/M.

• Manual tuning: you can manuall tune and

arrange TV channels in whatever order you need.

Select Press “ENTER” to select Press “MENU” to return

• Picture Mode: Vivid/Standard/Soft/User.

When User mode is selected, you can adjust contrast, brightness, saturation, sharpness and tint (in NTSC) of the image.

• Color Temperature: Normal/Warm/User/

Cool.

• Aspect ratio: Set the picture format:

4:3/14:9/16:9/Zoom1/Zoom2.

• DNR: Dynamic noise reduction effect for

+ 20 hidden pages