Hyundai H-LED15V8 User Manual [ru]

H-LED15V8

LED TV

ТЕЛЕВИЗОР

ЦВЕТНОГО ИЗОБРАЖЕНИЯ

ЖИДКОКРИСТАЛЛИЧЕСКИЙ

(LCD)

Руководство по эксплуатации Instruction manual

Table of contents

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start

Utilization of the product Important safeguards Installation

Stand installation

Connection

Outdoor antenna connection Other connections

Operation

Control elements

Front panel

Back panel Remote controller

Changing the battery

General operations

Teletext operations OSD operation

Picture setting Sound setting Setting page

Geometry setting

Channel setting

USB operation

General information File playback

General information

Troubleshooting

Causes of interference Accessories Specifications

2 3 3 3 4 4 5 5 5 5 6 6 6 6 7 7 8 8 8

9 10 10 10 10 11 11 11 13 13 13 14 14

Before you start

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Before connecting the AC power cord to the DC adapter outlet, make sure that the voltage designation of the DC adapter corresponds to the local electrical supply.

• Accessories include a DC adaptor marked with the TV model number. Do not use other adaptors with this unit.

• Please unplug the power cord from the AC outlet and contact a service center for repair if following occurs: any obvious abnormality appears in the unit, such as smoky, peculiar smell or strange sound; liquid has been spilled or other objects have fallen into the unit; no picture or sound; cover or panel is broken; although you have operated the unit following the operating instructions, it still cannot work normally.

• This unit can be connected to a power supply outlet without the third ground contact as well as with a ground contact.

• Always disconnect the power cord and antenna during a storm.

• Do not fix the power cord with a metal nail.

• Unplug the power cord from the AC outlet; also unplug the signal cables from the input ports when the unit is unused for long periods of time.

• When unplugging the plug, always hold the wide slot, do not touch the metal part, and do not destroy, refit, twist, pull or roast the power cord.

• Please contact the service center

immediately if you found that the core is showed in the air or has been broken.

• Please replace the AC outlet if the metal bolt cannot be inserted into the power socket completely or it cannot be fastened even when it was pushed in, otherwise, any accidents of shocks and fires would happen.

• Never touch the antenna lie or power plug if it stars to thunder.

• Do not touch the power plug with wet hands.

• Do not use any non-rated power socket with numerous devices jointed on one power socket or cable device. The wire of nondesignated capacity may cause the fire due to the generation of heat.

• All instructions must be read and understood well before you operate the unit. Heed all warnings and follow all instructions.

• Please use the accessories provided by the manufacturer. Using inadequate accessories may result in accidents.

• Please adjust the product through the panel buttons or the remote controller, do not remove the cover or attempt to service the product by yourself. Do not disassemble back cover and do not make maintenance by yourself to avoid the electric shock.

• Over-press the panel may destroy the product.

• Do not place the product on an unstable cart, stand surface, tripod, bracket, or table. The product may fall, causing serious accidents

Before you start

as well as the damage to the product.

• Please place the product on a flat surface in a well-ventilated location. Keep it away from the burning-light, direct sunlight, vibration, high-temperature and humidity.

• Do not place any vase, potted plant, cup, medicine and any container with water on this product. If the liquid is spilt, it may cause the fire, electric shock or breakdown.

• Do not install it at the place on the strong magnetic field or current field. It may cause break down. This equipment may be observed deterioration of the picture by electromagnetic radiation in electromagnetic environment.

• Fasten the wheel of the product or shelf with wheels when installing this product. If it moves or is tipped over, it may be damaged.

• Do not place any fire source such as candlelight close to this product or place it on this product. If it is tipped over or fallen down, it may cause damage or fire.

• Do not place the unit into closed space of TV for better ventilation; it can reduce the product lifetime. Keep a space at least 10 cm at above, left and right of the TV.

• Please place all the signal cords behind of rear panel.

• Do not overexert or touch the panel when you convey the product. Do not transfer the LED TV up or down display direction.

• Do not transport it with the power cable connected. If you move this product with the power cord or the connection cable connected, the damaged power cord, connection cable or connection terminal may cause the fire, the electric shock or breakdown.

• 2 persons or more shall transport the device, which is heavier than 18 kg. If you drop or tip over the device, it may damage it.

• The temperature of the product’s body becomes a little higher after a long period use. This phenomenon indicates that heat exchange in normal working mode, thus please do not let children or anyone who is sensitive of temperature to touch.

All images provided herein are schematic

drawings and may differ from of real objects.

Installation

Stand installation

Place the LED TV on a solid flat surface. Use soft material to place over the front screen to avoid any damage. Insert the support to the bottom of the unit:

Align the screw holes of the base with the holes of the stand and fix the base and the stand to the unit body with 3 supplied screws.

Connection

Wall mounting

For wall mounting the back panel of this unit is equipped with 2 screw holes (4 mm diameter, 100 mm horizontal spread distance). The accessories also include 2 screws designed for using with whic unit for wall-mounting. A wall-mount bracket should be used for wall mounting (the bracket is not included and should be acquired separately). Manufacturer is not responsible for improper mounting resulting in damage of the unit.

Connection

Outdoor Antenna Connection

Use 75Ω coaxial cable plug or 300-75Ω impedance converter to plug in antenna input terminal on the rear of the cabinet.

Other connections

• Connect a video source to the Composite

video input jack with RCA cable (not included).

• Connect an audio source to the proper

Audio input jacks (left and right).

• Connect the included DC adapter to the

DC input of this unit.

• When using the unit as a computer screen, connect the PC to the VGA jack of the unit by the relevant cable to get the video signal from the PC. For audio signal from the PC, connect the left and right jacks of the VGA/Component audio input of this unit to the audio output jack of the PC by using relevant connector (not included).

• If the video source has a HDMI output jack, you can connect the signal to the unit by HDMI cable (not included).

• Component input is intended for receiving component video signal if connected to the component output of external signal source.

• Connect an external device (e.g., VCR-/ DVD-recorder) to the proper Audio/Video output jacks of this unit with AV RCA cable (not included).

• Coaxial output is intended for transmitting multi-channel sound to an external decoder (e.g. in 5.1-CH format). RCA cable should be used for connection.

Operation

Control elements

Front panel

Back panel

1. IR sensor

2. Power indicator

1. PRO.+/- buttons

2. VOL+/- buttons

3. MENU button

4. SOURCE button

5. POWER button

6. Component video input

7. Audio stereo input

8. Composite video input

9. Stereo audio input-1/Audio input for VGA and component video

10. DC adaptor input

11. Composite video/audio output

12. HDMI input

13. VGA input

14. RF antenna jack

15. USB port

16. Stereo audio input-2

17. Composite video input-2

8 9 10 11 12 13 14

Operation

Remote controller (RC)

10 11

Index

Size Rev. Hold. Sub

10. PICTURE/REV button

11. MTS button/red button

12. Green button

13. POWER button

14. RETURN button

15. MENU button

16. EXIT button

17. INDEX button

18. CH+/CH- buttons

19. FREEZE/SUB button

20. SOUND/HOLD button

21. DEMO button

22. Cyan button/ button

Changing the battery

19 20

1. Remove the battery compartment cover on the back of the RC.

2. Insert the batteries into the battery compartment making sure that the correct polarity is observed.

3. Install the cover back.

1. button

2. Number buttons

3. INFO button

4. SOURCE button

5. Cursor (UP/DOWN/LEFT/RIGHT) buttons/ OK button

6. TXT button

7. VOL+/VOL- buttons

8. USB button

9. SCALE/SIZE button

1 2 3

• Use two AAA batteries for the RC. The RC should be pointed at remote sensor within 8 meters and within 30 degrees at the left or the right side.

• Take the battery out of the RC if it is not used for a long time.

• Do not mix new and used batteries or different types of batteries. Weak batteries can leak and severely damage the RC.

• Do not expose the RC to shock, liquids, and do not place it in an area with high humidity.

Operation

General operations

• Connect the terminal of the power cord to the power cord input of the TV (the position of the input is given in paragraph Control Elements above). Connect the plug of the power cord to the power supply outlet and then set the power switch on the rear panel to the on position, the power indicator will light up in red showing that the unit is in standby mode. To switch on the unit, press POWER button on the panel or on the RC; when the TV is on, the power indicator is off. Press POWER button again to switch the unit to the standby model, the power indicator will light up in red. To switch off the unit completely, set the power switch on the rear panel to the off position and then disconnect the power cord plug from the power supply outlet.

• Press VOL- button on the unit or on the RC repeatedly to decrease the volume; press VOL+ button on the unit or on the RC repeatedly to increase the volume.

• Press RETURN button on the RC to select from the present channel and the previously displayed channel.

• Press button to cut off sound, press this button again or adjust volume to resume sound.

• In TV mode press CH+/CH- buttons on the RC or on the unit to select previous or next channel; or press number buttons to enter a channel number directly.

• Press PICTURE button repeatedly to cycle through the available video picture modes from the following types: Standard => Bright => Soft => Personal.

• Press SOUND button repeatedly to cycle through the available sound modes from the following types: Stereo => Movie => Music => News => Personal.

• Press INFO button to display the preset TV channel information.

• In TV mode press MTS button to switch NICAM sound mode (not available for some channels).

• Press SCALE button repeatedly to select a screen display size from the available list: 4:3/Full/Subtitle/Wide/Zoom/Expand/Original/ Nature. Available aspects may differ for different signal sources.

• Press FREEZE button to freeze the picture on or off.

Press SOURCE button, then press cursor buttons on the RC to select a source from available source list: TV => YPbPr => PC => HDMI => AV1 => AV2. Press OK button to confirm. You can press USB button to access Media source mode directly; you can press TV button to access TV source mode directly.

• Press button to enable/disable Natural light function. This is to adjust the brightness of the backlight according to the content of the inputted signal automatically, so as to optimize the picture quality and decrease the power consumption.

• Press DEMO button to display the menu including E care (Eyes care), E saving (Energy saving) and E pic (Enhance picture) items. Press cursor buttons to select an item and press Ok button to demonstrate the selected mode of Natural light function. Press DEMO button or EXIT button to cancel.

It is recommended to demonstrate this

function in full-screen mode.

TELETEXT operations (option)

• Select the TV source mode. Then press CH-/CH+ buttons to select TV channel in order to pick up the picture signal of Teletext.

• Teletext button functions are as follows:

TXT: Press this button to enter into Teletext mode. Press this button to mix the teletext and current TV signal image. Press this button again to return to the channel you are watching.

HOLD: Press this button to stop the move to the next page. Press this button again to cancel operation.

INDEX: Press this button to go to the index page.

SIZE: Press this button to enlarge the top

Operation

part of the page. Press this button again to enlarge the bottom part of the page. Press this button third time to normal size text page view.

REV. (Reveal): Press this button to reveal the cancelled information. Press this button again to cancel the information.

SUB. (Subpage): Press this button to select sub-page. Input the number of sub-page and use numeric buttons in the format 0001 for sub page 1. The teletext will search for the sub page. Press SUBPAGE button again to exit the subpage mode.

Red/Green/Yellow/Cyan buttons: Press these 4 color buttons to access directly to corresponding color page displayed at the lower parts of teletext screen.

OSD operation

1. Press MENU button to enter the setting

menu displayed on the screen.

2. Press LEFT/RIGHT cursor buttons on the

RC to select setting page.

3. Press OK button on the RC to go to the

parameter list.

4. Press UP/DOWN cursor buttons on the

RC to select a parameter to adjust.

5. Press LEFT/RIGHT cursor buttons on the

RC to adjust the selected parameter.

6. Press MENU button to return to the previous menu page. Press EXIT button on the RC to quit the menu.

Some menu items may be in grey color, in this case they are not adjustable. Pictures of OSD menu are for reference only; they may differ from the real screens.

Picture setting page

Picture

Backlight Picture mode Scale Brightness Contrast Saturation Sharpness Tint Color temperature Natural light Dynamic contrast

• Backlight: adjust the brightness of screen

backlight depending on environmental lighting.

• Picture Mode: Standard/Bright/Soft/

Personal.

• Scale: 4:3/Full/Subtitle/Wide/Zoom/Ex--

pand/Original/Nature.

• Brightness, Contrast, Saturation,

Sharpness, Tint (tint available only for NTSC system).

• Color temperature: Select color

temperature mode of the picture - Normal/ Warm/Cool.

• Natural light: to adjust the brightness of

the backlight according to the content of the inputted signal automatically.

• Dynamic contrast: to adjust the image

contrast automatically.

Sound setting page

Sound

Sound mode Balance Sound EQ

• Sound mode: News/Music/Movie/Stereo/

Personal.

• Balance: adjust balance between left and

right speaker.

• Sound EQ: adjust the equalizer. Note:

after you adjust the equalizer, the sound mode will automatically switch to Personal.

Operation

Setting page

Setting

DNR Smart switch Startup setting Language TTX language Color system Watch time limit Time setting Restore to default

• DNR: Digital noise reduction effect for

reducing the video noise level: Off/On, if the broadcast signal received is weak.

• Smart switch:

Switch: when the connected external device is turned on, the TV will automatically switch to the corresponding source mode.

Display: when the connected external device is turned on, the TV will show a prompt message; select OK to switch to the corresponding source mode.

Off: disable Smart switch function.

• Startup setting: you can select the default

startup picture, captore picture (Logo) and no startup picture (Off).

• Language: select the language of the

OSD menu.

• TXT Language: select the language of the

teletext subtitles. If selected teletext language does not correspond to the program language, subtitles can be diplayed incorrectly.

• Color system: PAL/SECAM/NTSC.

• Watch time limit: set the period of time for

you to watch the TV; when the time elapses, the TV will switch off automatically. You must enter the password first (the default password is 0000; you can also assign your own password in PW Modify menu). If you forgot your password, you can use 0432 code.

• Time setting:

Current time: set the current time.

Turnon repeat: Select the mode of TV turnon at a specific time (Off/Once/Everyday). Note: If Off is selected, Turnon time, Wake source and Wake channel are unavailable.

Turnon time: set the time at which the TV will

turn on automatically.

Wake source: select the source mode to

which the TV will automatically turn on.

Wake channel: select the channel to which the TV will automatically turn on (available only if TV is selected as Wake source).

Turnoff repeat: Select the mode of TV turn-off at a specific time (Off/Once/Everyday). Note: If Off is selected, Turnoff time is unavailable.

Turnoff time: set the time at which the TV will turn off automatically.

Sleep time: set the period after which the TV will audomatically turn off (0 - 120 minutes).

• Restore to default: reset the parameters

to initial factory settings.

Geometry setting (only for PC mode)

Geometry

Auto adjust H position V position AD clock Phase

• Auto adjust: automatical setting of the

parameters.

• Horizontal Position: adjust horizontal

position of the image.

• Vertical Position: adjust vertical position

of the image.

• AD clock: adjust the image frequency

manually.

• Phase: adjust the phase manually.

Channel setting

Channel

Auto tuning Intellegent tuning Manual tuning Fine-tune Sound system Channel edit

• Auto tuning: press OK button to start

automatic search of available channels. To stop the process press MENU or EXIT button.

• Intellegent tuning: This operation will

+ 21 hidden pages