Hustler Turf Super Mini Z 44, Hustler ATZ, Hustler Mini Z 52, Super Z Diesel, Super Mini Z 52 User Manual

...

0 (0)

This manual applies to the following Hustler equipment lines:

Hustler Z/Super Z Super Z Diesel Hustler ATZ Hustler Mini Z 44/52 Super Mini Z 44/52

To the new owner

The purpose of this manual is to assist owners and operators in maintaining and operating the Hustler Z tractor and deck. Please read it carefully; information and instructions furnished can help you achieve years of dependable performance.

A separate Engine Manual is included with your owner’s packet which contains additional engine information that will not be repeated in this manual. You are urged to read it before attempting any operation or repair of the engine.

The Quick Reference Decals are designed to give the operator brief information needed in the daily operation of the machine. These decals are not intended to be used in place of this manual but instead is to be used as an extension of this manual. These decals should not be removed or obliterated. Replace these decals if they become unreadable.

It is the owner’s responsibility to make certain that the operator reads and understands this manual and the Quick Reference Decals before operating this machine. It is also the owner’s responsibility to make certain that the operator is a qualified and physically able individual, properly trained in the operation of this equipment. Local regulations may restrict the age of the operator.

IMPORTANT: For more detailed maintenance and adjustment information refer to the proper parts manual for your machine. Refer to the Product Literature section of this manual for ordering information.

Using this manual

General operation, adjustment and maintenance guidance is outlined for both the experienced and novice Hustler user. Operating conditions vary considerably and cannot all be addressed individually. Through experience, however, operators should find no difficulty in developing good operating skills suitable to most conditions.

Directions used in this manual, for example RIGHT or LEFT, refer to directions when seated on tractor facing forward, unless otherwise stated.

Photographs and illustrations used were current at the time of printing, but subsequent production changes may cause your machine to vary slightly in detail. Hustler Turf Equipment reserves the right to redesign and change the machine as deemed necessary, without notification. If a change has been made to your machine which is not reflected in this operator’s manual or the parts manual, see your Hustler dealer for current information and parts.

Warranty registration

The Delivery and Warranty Registration form must be completed and signed to validate your warranty protection. As the new equipment owner, you are expected to see that the form is completed and forwarded to Hustler Turf Equipment at time of delivery.

Be sure to register the tractor plus each attachment that displays a model and serial identification number plate with Hustler Turf Equipment.

IMPORTANT: Any unauthorized modification, alteration, or use of non-approved attachments voids the warranty and releases Hustler Turf Equipment from any liability arising from subsequent use of this equipment.

Model and serial number

Tractor model and serial numbers are found on the serial identification plate, located on the frame directly below and to the left of the operator’s platform.

These numbers are required on the Warranty Registration form. They will also assure you of the correct service parts when replacement becomes necessary.

Parts and service

Use original Hustler replacement parts only. These parts are available through your local Hustler dealer. To obtain prompt, efficient service, always provide the following information when ordering parts:

1. Correct part description

2. Correct model number.

3. Correct serial number.

All warranty repair and service must be handled through an authorized Hustler dealer. Arrangements should be made through your local service center.

GENERAL INFORMATION

600876_0706

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

WARNING:

600876_0706

HUSTLER Z/SUPER Z/HUSTLER ATZ/SUPER Z DIESEL/HUSTLER MINI Z/SUPER MINI Z

TWO YEAR LIMITED WARRANTY FOR TRACTORS AND DECKS

(THREE YEAR LIMITED WARRANTY ON DECK

SPINDLE BEARING & DECK GAUGE FORK BEARING)

WHAT IS COVERED BY THIS WARRANTY

Hustler Turf Equipment, makes the following warranty to the original purchaser only:

a. First and Second Year: Hustler Turf Equipment Tractors and Power

Units are warranted for two (2) years from date of delivery on all materials and workmanship. If the Purchaser discovers within this warranty period a defect in materials or workmanship:

● He must promptly notify Hustler Turf Equipment, or an

authorized dealer, in writing of the defect. In no event shall such notification be received by Hustler Turf Equipment, or an authorized dealer later than twenty-five (25) months from date of delivery.

● Within a reasonable time after such notification, Hustler Turf

Equipment, will correct any defect in material or workmanship on the Hustler Turf Equipment, by repairing or replacing part(s) with either new or used replacement parts.

● Such repair, including parts and labor shall be at the expense of

Hustler Turf Equipment, and,

b. Third Year: At the conclusion of the two year limited warranty

described in paragraph (a) above, there shall be an additional one year limited warranty on deck gauge fork bearings and deck spindle bearings only, no labor. If the Purchaser discovers within this warranty period a defect in either of these bearings:

● He must promptly notify Hustler Turf Equipment, or an

authorized dealer, in writing of the defect. In no event shall such notification be received by Hustler Turf Equipment, or an authorized dealer later than thirty-seven (37) months from date of delivery.

● Within a reasonable time after such notification, Hustler Turf

Equipment, will provide new replacement bearing to install on the Hustler Turf Equipment.

● The installation of the deck gauge fork bearing and deck spindle

bearing shall be at the expense of the owner, and,

c. Rental Units (90 days): Within 90 days of date of delivery Hustler

Turf Equipment, provides a limited warranty on all materials and workmanship for units used for rental purposes. If the Purchaser discovers within this warranty period a defect in materials or workmanship:

● He must promptly notify Hustler Turf Equipment, or an

authorized dealer, in writing of the defect. In no event shall such notification be received by Hustler Turf Equipment, or an authorized dealer later than 120 days from date of delivery.

● Within a reasonable time after such notification, Hustler Turf

Equipment, will correct any defect in material or workmanship on the Hustler Turf Equipment, by repairing or replacing part(s) with either new or used replacement parts.

● Such repair, including parts and labor shall be at the expense of

Hustler Turf Equipment, and,

d. Hustler Turf Equipment provides a limited warranty for the entire

length of ownership by the original purchaser for the following items:

● Against all defects in the frame resulting from frame breakage.

● Against all defects in the mowing deck which results in the front

edge of the deck being bent into the the blades.

● Against hydraulic hose and fitting leaks. If the original Purchaser discovers within this warranty period such a defect:

● He must promptly notify Hustler Turf Equipment or an authorized

dealer, in writing of the defect. Such notification must be received by Hustler Turf Equipment or an authorized dealer during the period when the equipment is owned by the original purchaser.

● Hustler Turf Equipment will correct any defect in the frame

resulting in frame breakage by repairing or replacing part(s) with new or used replacement parts.

● Hustler Turf Equipment will correct any defect in the deck

resulting in the front edge of the deck being bent into the blades by repairing or replacing part(s) with either new or used replacement parts.

● Such repair, including parts and labor, shall be at the expense of

Hustler Turf Equipment, and,

e. The engines are covered by a two (2) year limited warranty, by the

engine manufacturer, to the original owner (commercial or residential) only except the Caterpillar diesel engine which is covered by a three (3) year limited warranty, and,

f. The battery is covered by a one (1) year limited warranty to the

original owner only.

WHO MUST PERFORM THE WARRANTY SERVICE

All warranty service will be performed by dealers authorized by Hustler Turf Equipment. Service calls and/or transportation expense of the product to and from the authorized dealer, for warranty work, will be paid by the owner of the product. For warranty service you can contact an authorized dealer or write Hustler Turf Equipment, 200 South Ridge Road, Hesston, Kansas 67062, or call 1-620-327-4911.

WHAT IS NOT COVERED BY THIS WARRANTY

Hustler Turf Equipment, does not warranty:

● Some product, components or parts not manufactured by Hustler

Turf Equipment

● Repairs made by unauthorized persons

● Damage caused by use of the Hustler Turf Equipment for

purposes other than those for which it was designed

● Damages caused by disasters such as fire, flood, wind, and

lightening

● Damages caused by neglect, abuse, abnormal use, improper or

unreasonable use, accident, negligence or misuse

● Repairs or replacement resulting from the use of unauthorized

parts, accessories or attachments

● Repairs or replacement as the result if any alterations or

modifications, in the determination of Hustler Turf Equipment, which adversely affects the operation, performance or durability of the equipment.

● Hustler Turf Equipment which has the serial number removed or

made illegible

● Depreciation or damage caused by normal wear, lack of

reasonable and proper maintenance, failure to follow the product’s owner’s manual operating, maintenance and adjustment instructions or other operational instructions provided by Hustler Turf Equipment.

● Normal maintenance parts and service including, but not limited

to, filters, fuel, lubricants, tune-up parts, belts, blades, blade sharpening, bearings, brake or steering adjustments

● Repairs necessary due to improper fuel, contaminates in the fuel

system, or failure to properly prepare the fuel system prior to any period of non-use over three months

DISCLAIMER OF WARRANTY

The foregoing warranties are in lieu of all other warranties, expressed or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. However, if the Hustler Turf Equipment is purchased as a consumer product, any implied warranty of merchantability or fitness for a particular purpose is limited to the duration of this limited warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to

state.

LIMITATION OF REMEDIES

In no case shall Hustler Turf Equipment, be liable for any special, incidental, or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability in tort, or any other legal theory. Such damages include, but are not limited to:

● Loss of profits

● Loss of savings or revenue

● Loss of use of Hustler Turf Equipment or any associated

equipment

● Cost of capital

● Cost of any substitute equipment, facilities, services or downtime

● The claims of third parties including customers, and injury to

property Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

TIME LIMIT

Any action for breach of warranty must be commenced within twenty-five (25) months following delivery of the goods in a non-rental application. Any action for breach of warranty must be commenced within 120 days following delivery of the goods in a rental application.

NO OTHER WARRANTIES

Unless modified in writing, signed by both parties, and approved by the President of Hustler Turf Equipment, this agreement is understood to be the complete and exclusive agreement between the parties, superseding all prior agreements, oral or written, and all other communications between the parties relating to the subject matter of this agreement. No employee of Hustler Turf Equipment, or any other party is authorized to make any warranty in addition to those made in this agreement.

ALLOCATION OF RISKS

This agreement allocates the risks of product failure between Hustler Turf Equipment, and the purchaser. This allocation is recognized by both parties and is reflected in the price of the goods.

OWNER'S RESPONSIBILITY

You must maintain your Hustler Turf Equipment product following the maintenance procedures described in your owner's manual. Such routine maintenance, whether performed by a dealer or by you, is at your expense.

This machine like any other powered equipment is potentially dangerous unless properly operated. Any operator must be cautious and

keep safety in mind at all times. Any operator, prior to using the Hustler Turf Equipment, should thoroughly familiarize himself with the owner's manual regarding operation and safety of the machine, as well as all safety warnings on the machine itself.

WARRANTY REGISTRATION

1. Register the unit on-line at www.Hustler dealer.com or by filling out the Warranty registration form, provided in the owner’s packet. If using the Warranty registration form it MUST be completed and signed by the authorized dealer and original purchaser.

2. For validation, the completed Warranty registration form MUST be forwarded to Hustler Turf Equipment, within ten (10) days following date of purchase.

3. The date of purchase constitutes delivery.

600876_0706

This safety alert symbol is used to call attention to a message intended to provide a reasonable degree of PERSONAL SAFETY for operators and other persons during the normal operation and servicing of this equipment.

DANGER – denotes immediate hazards which WILL result in severe personal injury or death.

WARNING - denotes a hazard or unsafe practice which COULD result in severe personal injury or death.

This manual uses two other words to highlight information.

IMPORTANT calls attention to special mechanical information and NOTE: emphasizes general information worthy of special attention.

All operators should read this manual, or be instructed about safe operating and maintenance procedures. This is the owner’s responsibility.

Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert ▲▲symbol, which means DANGER or WARNING - “personal safety instructions.” Failure to comply with the instructions may result in personal injury or death.

Incorrect usage of this machine may result in severe injury. Personnel operating and maintaining it should be trained in the proper use and should read the manuals completely and thoroughly before attempting to set-up, operate, adjust, or service this machine.

The owner should also ensure that the operator/mechanic know that they are responsible for their own safety as well as the safety of other persons within the vicinity. Remember, the operator is responsible for accidents or hazards occurring to other people or their property.

SAFETY PRECAUTIONS

Safety and Instruction Decals

▲▲

Specific safety warning decals are located on the equipment near the immediate areas of potential hazards. These decals should not be removed or obliterated. Replace them if they become non-readable.

The following illustrations show the various decals that are located on the machine. A brief explanation, for those requiring one, is shown to help the operator understand the meanings of these decals.

Read Owner’s Manual and Quick Reference Decal before attempting to operate this machine.

Do not smoke while refueling. Do not fill tank with engine running, or while the engine is hot. Allow engine to cool before storing machine inside a building. Store away from open flame or spark if there is fuel in tank. Clean up any gasoline spills. Do not refuel while in enclosed trailer or other enclosed areas

Do not remove or modify stabilizer wheels or injury can result. Never stop suddenly while backing down slopes. This action may result in a reaction of the tractor that can cause serious physical injury.

Keep shields or covers in place while machine is in operation. Keep hands away from rotating pulleys and belts.

Whirling blades! Keep hands and feet away. Beware of thrown objects.

Never operate the mower deck with side deflector removed or in raised position, except when the grass catcher attachment is being used.

Hot surface!

Avoid skin contact with battery acid. Always wear eye protection when checking the battery, acid can cause serious injury to skin and eyes. If contact occurs, flush area with clean water and call physician immediately. Acid will also damage clothing. Do not allow open flame near the battery when charging. Hydrogen gas forms inside the battery. This gas is both toxic and flammable and may cause an explosion if exposed to flame. Always remove the negative ground first and replace it last. Do not overfill battery. Electrolyte may overflow and damage paint, wiring or structure. When cleaning the battery, use soap and water. Be careful not to get soap and water into the battery. Use soda mixed in water to clean corrosion off the terminals.

Hydraulic fluid escaping under pressure can penetrate skin. Hydraulic fluid may also cause infection in a minor cut or opening in the skin; if exposed to hydraulic fluid, see a doctor at once. Before applying pressure to hydraulic system, make sure all connections are tight and all hoses and lines are in good condition. Relieve all pressure in the system before disconnecting or working on hydraulic lines. To find a leak under pressure, use a piece of cardboard or wood – never use your hands. To relieve all pressure in system, turn engine off and lower attachment.

Keep engine and pump compart-ment(s) clean (especially in exhaust area) to prevent fire and provide maximum engine and hydraulic cooling.

Avoid crushing Do not jump if machine tips Use seat belt Seat belt must be fastened while operating this machine. Failure to use seat belt will result in serious injury in the event of a roll over.

Use seat belt.

This structure’s protective capability may be impaired by structural damage, overturn, or alteration. To minimize chance of injury or death from rollover; keep ROPS in the raised and locked position and use the seat belt. There is no roll over protection when the ROPS is in the lowered position. Lower the ROPS only when absolutely necessary. Drive slowly and carefully. Raise the ROPS as soon as clearance permits. Read and follow sloper operation instructions and warnings. Do no wear seat belt when the ROPS is in the lowered position.

600876_0706

If you loose steering control while operating the machine, place the steering control levers in the park brake position immediately. Inspect the machine and involve your Hustler dealer to resolve the problem before continuing to operate.

If pump belt fails, steering control will be lost. Refer to owner’s manual for

inspection and replacement intervals and refer to above paragraph for emergency procedures.

If you lose steering control while operating the machine, place the steering

Part Number

600899

control levers in the park brake position immediately. Inspect the machine and involve your Hustler dealer to resolve the problem before continuing to operate.

If pump belt fails, steering control will be lost. Refer to owner’s manual for inspection and replacement intervals and refer to above paragraph for emergency procedures.

600899

600876_0706

C (5o)

D (10o)

E (15o)

Line A

Line B

Slope Guide Lines

F (25o) - Hustler ATZ only

600876_0706

1. Hold this sheet of paper in front of you. Make sure that line A is horizontal.

2. Align line B with a vertical surface such as a pole, tree or building.

3. Fold the paper along the slope guide lines (C, D or E).

4. Align the closest slope guide line with the ground slope. This will give you a close estimation of the ground slope to be mowed.

SLOPE GUIDE

Figure 2-1

Use this diagram when determining the degree of slope to be mowed.

600876_0706

Safe Operating Practices

Some of the following safety instructions are from ANSI Standard B-

71.4-1999 while others are specific to the Hustler Mid Mount Z line. This product is capable of amputating hands and feet and throwing

objects. Always follow all safety instructions to avoid serious injury or death.

Operation

▲

Never leave a running machine unattended. Always disengage deck clutch, place control levers in park brake position, stop tractor engine, and remove ignition key when leaving operator’s seat.

▲

Always remain seated while operating machine.

▲

Always keep safety shields and covers in place, except for servicing.

▲

Always maintain a safe distance from people and pets when mowing. Always stop machine if someone enters the area.

▲

Always operate machine in daylight or with adequate working lights.

▲

Follow daily and weekly checklists, making sure hoses are tightly secured and bolts are tightened.

▲

Always observe traffic laws while driving machine from one location to another. Watch for traffic when operating near or crossing roadways.

▲

Always be alert for hazards such as rocks, metal objects and other debris which may be thrown or entangled by mower blades. Watch out for holes or deep depressions.

▲

Inspect area to be mowed for hazards such as rocks, metal objects and other debris which may be thrown or entangled by mower blades. Remove these objects before mowing.

▲

Always inspect machine for damage after striking a foreign object. If damage is found, repair machine immediately. Be sure to disengage deck clutch, place control levers in park brake position, stop tractor engine, and remove ignition key when leaving operator’s seat to inspect damage.

▲ Always wear adequate ear protection, such as earplugs, when

operating this equipment as prolonged exposure to uncomfortable or loud noises can cause impairment or loss of hearing. Do not wear radios or music headphones while operating the machinery. Safe operation requires your full attention.

▲ Do not operate the equipment while wearing sandals, tennis shoes,

sneakers, shorts or any type of loose fitting clothing. Always wear long pants, safety glasses, ear protection and safety shoes when operating this machine.

▲

Always be aware of what is behind the machine before backing up. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing up.

▲

Never push forward suddenly on your control levers while the machine is in rearward motion because machine may tip backwards.

▲

Never pull back suddenly on your control levers while the machine is in forward motion.

▲

When moving in reverse, push forward slowly on control levers and avoid sudden movement. Rapid movement of the control levers in either direction could result in a reaction of the tractor that can cause serious injury.

▲

Never operate a poorly maintained machine.

▲

Never attempt high speed maneuvering, especially in crowded or congested areas.

▲

Never allow persons to operate this machine without proper instruction or allow children to operate machine. Allow only responsible adults who are familiar with these instructions to operate this machine.

▲

Never put hands or feet under any part of the machine while it is running.

▲

Never carry passengers.

▲

Always disengage the blades and wait for them to stop before crossing gravel drives, walks or roads.

▲

Always keep clear of the mower blades and attachments during their operation.

▲

Turn off blades when not mowing.

▲

Slow down before turning.

▲

Stop the engine before removing the grass catcher or unclogging the

discharge chute. Never clear the discharge chute with the engine running. Turn off the engine and be sure the blades have stopped before cleaning. Use a stick to clear a plugged discharge area.

Never use your hand!

▲

Always keep clear of the mower blades and attachments during operation.

▲

Do not operate the machine while under the influence of alcohol or drugs.

▲

Exercise caution when loading or unloading the machine onto a trailer or truck.

▲

Always wear safety goggles or safety glasses with side shields when operating the mower.

▲

Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the mower safely enough to protect themselves and others from serious injury.

▲

If any attachment or additional weight is mounted on the rear of the unit, any rapid movement of the control levers in either direction could result in a reaction of the tractor that can cause serious injury.

▲▲

Clean flammable material from machine. Prevent fires by keeping engine compartment, battery, fuel line, fuel tank and operator’s station clean of accumulated trash, grass clippings, and other debris. Always clean up spilled fuel and oil.

▲

Always buckle seat belt, if provided with one, and only if a ROPS is installed properly, before starting tractor.

Using a ramp

▲

Use extreme caution when loading and unloading a unit with a ramp.

▲

Use only a single, full width ramp; do not use individual ramps for each side of the unit. Having a full width ramp provides a surface for the tractor frame to contact if the unit starts to tip backwards. It also reduces the risk of a wheel going off and the machine tipping over.

▲

Do not exceed a 15 degree angle between the ramp and the ground or between the ramp and the trailer or truck.

▲

When on a ramp avoid sudden acceleration

Slope Operation

Slopes are a major factor in loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it; do not mow it.

▲

Use extreme caution when operating on slopes.

• Be extremely careful changing directions on a slope. Slow down.

• Do not operate where the machine could slip or tip.

• Turn slowly

• Turn on the most level part of the slope

• To maximize traction, it is better to turn the front of the machine uphill, rather than downhill. If drive tires lose traction, steering

control is lost which could cause serious injury or death.

▲

Do not remove or modify the stabilizer wheels.

▲

Watch for holes, ruts or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles.

▲

Remove obstacles such as rocks, tree limbs, etc.

▲

Keep all movement on slopes slow and gradual. Do not make sudden changes in speed or direction.

▲

Avoid starting and stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope.

▲

Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.

▲

Mow a safe distance (minimum of two mower widths) away from drop-offs, retaining walls, drainage ditches, steep banks, water, and other types of hazards to avoid a wheel dropping over the edge or to avoid the ground from breaking away. This will help avoid machine rollover and serious injury or death.

▲

Use a walk behind or push mower on slopes and near drop-offs, retaining walls, drainage ditches, steep banks and water to avoid machine rollover and serious injury or death.

OPERATION

600876_0706

▲

Do not mow on wet grass. Reduced traction could cause sliding.

▲

Do not try to stabilize the machine by putting your foot on the ground.

▲

If the mower’s tires lose traction when operating on slopes, disengage the blades, place the control levers in the park brake position, turn the engine off and get help.

▲

Never make sudden starts, stops, turns, or reverse direction, especially when maneuvering on slopes. The steering is designed for sensitive response. Rapid movement of the control levers in either direction could result in a reaction of the tractor that can cause serious injury.

▲

Never stop suddenly while backing down slopes. This action may result in a reaction of the tractor that can cause serious physical injury.

▲

The Hustler mower is capable of operating horizontally (traverse) on moderately steep slopes. When operating on slopes up to 15 degrees, be aware of any conditions that may cause the tractor drive tires to lose traction resulting in a possible loss of control of the machine. An operator should not operate on a slope until he is thoroughly familiar with the equipment.

Do not operate on slopes greater than 15 degrees.

Refer to Figure 2-1, page 7, when determining the degree of slope to be mowed.

IMPORTANT: The Hustler ATZ only, is capable of operating on slopes of 15 degrees or more (maximum 25 degrees). Do not

operate the Hustler ATZ on slopes greater than 25 degrees.

Refer to Figure 2-1, page 7 when determining the degree of slope to be mowed.

It is strongly recommended that the operator drive the machine off of the slope, using extreme caution, if any sign of loss of traction is detected. Wait until the condition that caused the problem is resolved before attempting to operate on the slope again.

Terrain conditions can affect traction resulting in possible loss of control of the machine. Some of the conditions to be aware of are:

1. Wet terrain

2. Depressions in the ground; i.e. holes, ruts, washouts

3. Mounds of dirt

4. Soil type; i.e. sand, loose dirt, gravel, clay

5. Grass type, density, and height

6. Extremely dry conditions of grass

7. Tire pressure

The attachments mounted to the tractor will also affect the way it handles on a slope. Be aware that each attachment’s characteristics vary.

Another consideration to safe mowing on slopes is to be aware of what is located at the bottom of the slope. Extreme caution should be used when there is a hazard located at the bottom of the slope. Some examples are:

1. Water; i.e. lake, river

2. Cliffs, retaining walls

3. Roads, highways

4. Buildings

5. Rocks

These are just a few examples of situations when caution must be used when operating on a slope. There are many other possibilities too numerous to mention. Just remember to always exercise extreme caution when operating on any slope.

▲ When operating on terrain where there is a potential for a roll

over, it is important that a ROPS be installed on the equipment. The ROPS will minimize chance of injury or death from rollover. Seat belt must be fastened while operating a machine equipped with ROPS. Failure to use seat belt will result in serious injury in the event of a roll over.

Children

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.

▲

Never leave machine unattended with ignition key in switch, especially with children present.

▲

Children or bystanders may be injured if they move or attempt to operate the tractor while it is unattended. Always disengage deck clutch, place control levers in park brake position, stop tractor engine, and remove ignition key when leaving operator’s seat.

▲

Keep children out of the mowing area and under the watchful care of another responsible adult.

▲

Be alert and turn the machine off if children enter the area.

▲

Before and while backing, look behind and down for small children.

▲

Never carry children, even with the blades off. They may fall off and be seriously injured or interfere with safe machine operation.

▲

Never allow children to operate the machine.

▲

Use care when approaching blind corners, shrubs, trees, the end of a fence or other objects that may obscure vision.

IMPORTANT: When access is required under the seat platform and the seat is equipped with the optional arm rests, make certain to place the control arms in the park brake position and pivot the arm rests upward before placing the seat platform in the full forward position to prevent arm rest damage.

Control Panel

A. Choke control (Fig. 3-1) – a cable is linked to manually operate the

engine choke. When the lever is in the down position, the choke is in the off (run) position. When the lever is pulled up, the choke is in the on (start) position. Do not operate the machine in the on (start) position. NOTE: The choke control is not used on Models 927053 & 927061.

B. Throttle control (Fig. 3-1) — a cable is linked to engine throttle for

controlling engine speed. Move lever forward to increase engine rpm, move lever rearward to decrease engine rpm.

C. Deck clutch switch (Fig. 3-1) — this switch engages the deck. Pull

the switch up to engage and push switch down to disengage the clutch. IMPORTANT: Never engage clutch with engine running at high rpm or when the deck is under load. Clutch, belts or deck could be damaged.

D. Ignition switch (Fig. 3-1) – a three position switch: off, run, and

start. With key inserted, rotate it clockwise to START position; release key when engine starts, and switch will automatically return to the RUN position.

E. Oil pressure light and alarm (Fig. 3-1) — this light comes on

Kohler EFI

units only

Kawasaki liquid

cooled units only

A - Choke F - Check engine light B - Throttle G - Temperature warning light C - Deck clutch switch H - Alternator warning light D - Ignition switch I - Pre-heat switch E - Oil pressure light J - Hour meter

Figure 3-1

Control Panels

CAT diesel

units only

when the ignition switch is placed in the RUN position and stays lit until the engine is running and a safe oil pressure is developed. If light comes on during operation, shut engine off immediately and locate and correct the problem. Models 927558 and 927566 only — an audible alarm will sound when the engine oil pressure drops below normal operating pressure.

F. Check engine light (Fig. 3-1) — refer to Kohler engine owner’s

manual for details.

G. Temperature warning light and alarm (Fig. 3-1) — this light will

come on when the engine coolant temperature reaches an unsafe level during operation. If light comes on, shut down the machine as soon as possible. Never risk continued operation when light remains on; high temperatures can severely damage the engine. Never risk continued operation when light remains on: high temperatures can severely damage the engine. Models 927558 and 927566 & Diesel units only — an audible alarm will sound when the engine coolant is close to overheating.

H. Alternator warning light (Fig. 3-1) — this light comes on when

the ignition switch is placed in the RUN position and stays lit until the engine is running and the battery is being charged. If light comes on during operation, shut engine off immediately, locate and correct the problem. If light remains on while engine is running, it indicates that the battery(s) is being discharged.

I. Pre-heat switch (Fig. 3-1) — this is an intermittent rocker switch

position. Turn ignition key to run, depress and hold pre-heat switch six (6) seconds to start engine.

600876_0706

+ 25 hidden pages