Hustler Turf Lawn Mower Accessory User Manual

GENERAL INFORMATION

This manual applies to the following Hustler equipment lines:

Mini FasTrak 36/42 FasTrak 36/42/48/54

To the new owner

The purpose of this manual is to assist owners and operators in maintaining and operating the FasTrak tractor and deck. Please read it carefully; information and instructions furnished can help you achieve years of de pen d able performance.

A separate Engine Owner’s Manual is included with your owner’s packet which contains additional engine information that will not be repeated in this manual. You are urged to read it before attempting any operation or repair of the engine.

The Quick Reference Decals are designed to give the operator brief information needed in the daily operation and service of the machine. These decals are not intended to be used in place of this manual but instead are to be used as an extension of this manual. These decals should not be removed or obliterated. Replace these decals if they become unreadable.

It is the owner’s responsibility to make certain that the operators and mechanics read and understand this manual and all decals before operating this machine. It is also the owner’s responsibility to make certain that the operators and mechanics are qualified and physically able individuals, properly trained in the operation of this equipment. All operator and mechanics must become familiar with the safe operation of the equipment, operator controls and safety signs.

Never let children or untrained people operate or service the equipment. Local regulations may restrict the age of the operator.

IMPORTANT: For more detailed maintenance and adjustment information refer to the proper parts manual f or your machine. Refer to the Product Literature section of this manual for ordering information.

The owner/user can prevent andis responsible for accidents or injuries occurring to themselves, other people or property.

Using this manual

General operation, adjustment and maintenance guidance is outlined for both the experienced and novice Hustler user . Operating conditions vary considerably and cannot all be addressed individually. Through experience, however, operators should find no difficulty in developing good operating skills suitable to most conditions.

Directions used in this manual, for example RIGHT or LEFT, refer to directions when seated on tractor facing forward, unless otherwise stated.

Photographs and illustrations used were current at the time of printing, but subsequent production changes may cause your machine to vary slightly in detail. Hustler Turf Equipment reserves the right to redesign and change the machine as deemed necessary, without notification. If a change has been made to your machine which is not reflected in this owner’s manual, or the parts manual, see your Hustler dealer for current information and parts.

Warranty registration

The Delivery and Warranty Registration form must be completed and signed to validate your warranty protection. As the new equipment owner, you are expected to see that the form is completed and forwarded to Hustler Turf Equipment at time of delivery.

Be sure to register the tractor plus each attachment that displays a model and serial identification number plate with Hustler Turf Equipment.

IMPORTANT: Any unauthorized modification, alteration, or use of non-approved attachments voids the warranty and releases Hustler Turf Equipment from any liability arising from subsequent use of this equipment.

Model and serial number

Tractor model and serial numbers are found on the serial identification plate, located on the frame directly below and to the right of the operator ’s platform.

These numbers are required on the Warranty Registration form. They will also assure you of the correct service parts when replacement becomes necessary.

Parts and service

Use original Hustler replacement parts only. These parts are available through your local Hustler dealer. To obtain prompt, efficient service, always provide the following information when ordering parts:

1. Correct part description

2. Correct model number.

3. Correct serial number.

All warranty repair and service must be handled through an authorized Hustler dealer. Arrangem ents should be made th rough y our local service center.

WARNING:

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

IMPORTANT: This engine is n ot eq uipped with a spark arrester muf fler. It is a violation of California Public Resource Code Section 4442 to use or operate this engine on any forest-covered, brush-covered, or grass-covered unimproved land. Other states or f e deral areas may have similar laws.

This spark ignition system complies with Canadian ICES-002.

The enclosed Engine Owner’s Manual is supplied for information regarding the U.S. Environmental Protection Agency (EPA) and the California Emission Control Regulation of emission systems, maintenance and warranty.

Keep this Engine Owner’s Manual with your unit. Should the Engine Owner’s Manual become damaged or illegible, replace immediately. Replacements may be ordered per the information found in the Product Information section of this manual.

601156_0308 1

2 601156_0307

MINI FASTRAK 36/42 TRACTORS & DECKS

FASTRAK 36/42 TRACTORS & DECKS

HUSTLER TURF CONSUMER PRODUCT THREE YEAR FULL WARRANTY FOR RESIDENTIAL USE (90 DAYS LIMITED WARRANTY FOR COMMERCIAL USE)

UNITS WITH SERIAL NUMBER 0701 (FIRST 4 DIGITS) AND LATER

WHAT IS COVERED BY THIS WARRANTY

Hustler Turf Equipment, makes the following warranty to the original purchaser only:

a. Residential use: Hustler Turf Consumer Products used for normal

residential purposes* are warranted for three (3) years from date of delivery on all materials and workmanship. If the Purchaser discovers within this warranty period (three years from date of delivery) a defect in materials or workmanship:

● He must promptly notify Hustler Turf Equipment, or an authorized dealer, in writing of the defect. In no event shall such notification be received by Hustler Turf Equipment, or an authorized dealer later than thirty-seven (37) months from date of delivery.

● Within a reasonable time after such notification, Hustler Turf Equipment, will correct any defect in material or workmanship on the Hustler Turf Equipment, by repairing or replacing part(s) with either new or used replacement parts.

● Such repair, including parts and labor shall be at the expense of Hustler Turf Equipment, and,

* Normal residential purpose means use of product on same lot as your home. Use at more than one location is considered commerical

use, and then the commercial use warranty would apply.

b. Commerical use: Hustler Turf Consumer Products used for commer-

cial or institutional use are warranted for 90 days from date of deliv-

ery, on all materials and workmanship. (Rental use is warranted for 90 days) NOTE: An hour meter kit must be installed to receive warranty coverage on Commercial units.

If the Purchaser discovers within this warranty period such a defect:

● Such repair, including parts and labor shall be at the expense of Hustler Turf Equipment, and,

c. Hustler Turf Equipment provides a limited warranty for the entire

length of ownership by the original purchaser (residential only)

for the following items:

● Against all defects in the tractor frame resulting from frame break- age.

● Against all defects in the mowing deck which results in the front edge of the deck being bent into the the blades.

If the original Purchaser discovers within this warranty period such a defect:

● He must promptly notify Hustler Turf Equipment or an authorized dealer, in writing of the defect. Such notification must be received by Hustler Turf Equipment or an authorized dealer during the period when the equipment is owned by the original purchaser.

● Hustler Turf Equipment will correct any defect in the frame resulting in frame breakage by repairing or replacing part(s) with new or used replacement parts.

● Hustler Turf Equipment will correct any defect in the deck resulting in the front edge of the deck being bent into the blades by repairing or replacing part(s) with either new or used replacement parts.

● Such repair, including parts and labor, shall be at the expense of Hustler Turf Equipment, and,

d. The Honda engine is covered by a two (2) year limited warranty, by

the engine manufacturer, to the original owner (commercial or residential) only, and,

The Kohler Courage engine is covered by a two (2) year limited warranty, by the engine manufacturer, to the original owner (residential only) and a 90 day limited warranty, by the engine manufacturer, to the original owner (commercial only), and,

e. The battery is covere d by a on e (1) yea r limited warranty to the orig-

inal owner only.

WHO MUST PERFORM THE WARRANTY SERVICE

All warranty service will be performed by dealers authorized by Hustler Turf Equipment. Service calls and/or transportation expense of the product to and from the authorized dealer, for warranty work, will be paid by the owner of the product. For warranty service contact an authorized dealer.

WHAT IS NOT COVERED BY THIS WARRANTY

Hustler Turf Equipment, does not warranty:

● Some product, components or parts not manufactured by Hustler Turf Equipment

● Repairs made by unauthorized persons

● Damage caused by use of the Hustler Turf Equipment for purposes

other than those for which it was designed

● Damages caused by disasters such as fire, flood, wind, and lightening

● Damages caused by neglect, abuse, abnormal use, improper or unreasonable use, accident, negligence or misuse

● Repairs or replacement resulting from the use of unauthorized parts, accessories or attachments

● Repairs or replacement as the result if any alterations or modifications, in the determination of Hustler Turf Equipment, which adversely affects the operation, performance or durability of the equipment.

● Hustler Turf Equipment which has the serial number removed or made illegible

● Depreciation or damage caused by normal wear, lack of reasonable and proper maintenance, failure to follow the product’s owner’s manual operating, maintenance and adjustment instructions or other operational instructions provided by Hustler Turf Equipment.

● Normal maintenance parts and service including, but not limited to, filters, fuel, lubricants, tune-up parts, belts, blades, blade sharpening, bearings, brake or steering adjustments

● Repairs necessary due to improper fuel, contaminates in the fuel system, or failure to properly prepare the fuel system prior to any period of non-use over three months

DISCLAIMER OF WARRANTY

The foregoing warranties are in lieu of all other warranties, expressed or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. However, if the Hustler Turf Equipment is purchased as a consumer product, any implied warranty of merchantability or fitness for a particular purpose is limited to the duration of this limited warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

LIMITATION OF REMEDIES

In no case shall Hustler Turf Equipment, be liable for any special, incidental, or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability in tort, or any other legal theory. Such damages include, but are not limited to:

● Loss of profits

● Loss of savings or revenue

● Loss of use of Hustler Turf Equipment or any associated equipment

601156_0308 3

● Cost of capital

● Cost of any substitute equipment, facilities, services or downtime

● The claims of third parties including customers, and injury to prop-

erty Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

TIME LIMIT

Any action for breach of warranty must be commenced within thirty-seven (37) months following delivery of the goods in a residential application. Any action for breach of warranty must be commenced within 120 days following delivery of the goods in a commercial application.

NO OTHER WARRANTIES

Unless modified in writing, signed by both parties, and approved by the President of Hustler Turf Equipment, this agreement is understood to be the complete and exclusive agreement between the parties, superseding all prior agreements, oral or written, and all other communications between the parties relating to the subject matter of this agreement. No employee of Hustler Turf Equipment, or any other party is authorized to make any warranty in addition to those made in this agreement.

ALLOCATION OF RISKS

This agreement allocates the risks of product failure between Hustler Turf Equipment, and the purchaser. This allocation is recognized by both parties and is reflected in the price of the goods.

OWNER'S RESPONSIBILITY

You must maintain your Hustler Turf Consumer Product following the maintenance procedures described in your owner's manual. Such routine maintenance, whether performed by a dealer or by you, is at your expense.

This machine like any other powered equipment is potentially dangerous unless properly operated. Any operator must be cautious and keep safety

in mind at all times. Any operator, prior to using the Hustler Turf Equipment, should thoroughly familiarize himself with the owner's manual regarding operation and safety of the machine, as well as all safety warnings on the machine itself.

WARRANTY REGISTRATION

1. Dealers must register the unit on-line at www.Hustlerdealer.com or by

filling out the Warranty registration form, provided in the owner’ s packet. If using the Warranty registration form it MUST be completed and signed by the authorized dealer and original purchaser.

2. For validation, the completed Warranty registration form MUST be for-

warded to Hustler Turf Equipment, within ten (10) days following date of purchase.

3. The date of purchase constitutes delivery.

4 601156_0308

FASTRAK 48/54 TRACTORS & DECKS

HUSTLER TURF CONSUMER PRODUCT

FOUR YEAR OR 400 HOURS FULL WARRANTY FOR RESIDENTIAL USE

(ONE YEAR OR 400 HOURS LIMITED WARRANTY FOR COMMERCIAL USE)

MODELS 928267, 928275, 928291, 928502, 928520

WHAT IS COVERED BY THIS WARRANTY

Hustler Turf Equipment, makes the following warranty to the original purchaser only:

a. Residential use: Hustler Turf Consumer Products used for normal

residential purposes* are warranted for four (4) years or 400 hours from date of delivery on all materials and workmanship. If the Purchaser discovers within this warranty period (four years from date of delivery) a defect in materials or workmanship:

● Such repair, including parts and labor shall be at the expense of Hustler Turf Equipment, and,

* Normal residential purpose means use of product on same lot as your home. Use at more than one location is considered commerical

use, and then the commercial use warranty would apply.

b. Commerical use: Hustler Turf Consumer Products used for commer-

cial or institutional use are warranted for one (1) year or 400 hours of use, whichever comes first, from date of delivery, on all materials and workmanship. (Rental use is warranted for 90 days)

NOTE: An hour meter kit must be installed to receive warranty coverage on Commercial units.

If the Purchaser discovers within this warranty period such a defect:

● Such repair, including parts and labor shall be at the expense of Hustler Turf Equipment, and,

c. Hustler Turf Equipment provides a limited warranty for the entire

length of ownership by the original purchaser (residential only)

for the following items:

● Against all defects in the tractor frame resulting from frame break- age.

● Against all defects in the mowing deck which results in the front edge of the deck being bent into the the blades.

If the original Purchaser discovers within this warranty period such a defect:

●

Hustler Turf Equipment will correct any defect in the frame resulting in frame breakage by repairing or replacing part(s) with new or used replacement parts.

● Such repair, including parts and labor, shall be at the expense of Hustler Turf Equipment, and,

d. The Honda engine is covered by a two (2) year limited warranty, by

the engine manufacturer, to the original owner (commercial or residential) only, and,

The Kohler Courage engine is covered by a two (2) year limited warranty, by the engine manufacturer, to the original owner (residential) only and a 90 day limited warranty, by the engine manufacturer, to the original owner (commercial only), and, The Kawaski engine is covered by a two (2) year limited warranty, by the engine manufacturer, to the or iginal owner (commercial or residential) only, and,

e. The battery is covered by a one (1) year limited warranty to the orig-

inal owner only.

WHO MUST PERFORM THE WARRANTY SERVICE

WHAT IS NOT COVERED BY THIS WARRANTY

Hustler Turf Equipment, does not warranty:

● Some product, components or parts not manufactured by Hustler Turf Equipment

● Repairs made by unauthorized persons

● Damage caused by use of the Hustler Turf Equipment for purposes

other than those for which it was designed

● Damages caused by disasters such as fire, flood, wind, and lightening

● Damages caused by neglect, abuse, abnormal use, improper or unreasonable use, accident, negligence or misuse

● Repairs or replacement resulting from the use of unau thorized par ts, accessories or attachments

● Hustler Turf Equipment which has the serial number removed or made illegible

● Normal maintenance parts and service including, but not limited to, filters, fuel, lubricants, tune-up parts, belts, blades, blade sharpening, bearings, brake or steering adjustments

● Repairs necessary due to improper fuel, contaminates in the fuel system, or failure to properly prepare the fuel system prior to any period of non-use over three months

DISCLAIMER OF WARRANTY

LIMITATION OF REMEDIES

601156_0308 5

● Loss of profits

● Loss of savings or revenue

● Loss of use of Hustler Turf Equipment or any associated equipment

● Cost of capital

● Cost of any substitute equipment, facilities, services or downtime

● The claims of third parties including customers, and injury to prop-

erty Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

TIME LIMIT

Any action for breach of warranty must be commenced within forty-nine (49) months following delivery of the goods in a residential application. Any action for breach of warranty must be commenced within thirteen (13) months following delivery of the goods in a commercial application. Any action for breach of warranty must be commenced within 120 days following delivery of the goods in a rental application.

NO OTHER WARRANTIES

ALLOCATION OF RISKS

This agreement allocates the risks of product failure between Hustler Turf Equipment, and the purchaser. This allocation is recognized by both parties and is reflected in the price of the goods.

OWNER'S RESPONSIBILITY

You must maintain your Hustler Turf Equipment product following the maintenance procedures described in your owner's manual. Such routine maintenance, whether performed by a dealer or by you, is at your expense.

This machine like any other powered equipment is potentially dangerous unless properly operated. Any operator must be cautious and keep safety

WARRANTY REGISTRATION

1. Dealers must register the unit on-line at www.Hustlerdealer.com or by

filling out the Warranty registration form, provided in the owner’ s packet. If using the Warranty registration form it MUST be completed and signed by the authorized dealer and original purchaser.

2. For validation, the completed Warranty registration form MUST be for-

warded to Hustler Turf Equipment, within ten (10) days following date of purchase.

3. The date of purchase constitutes delivery.

6 601156_0308

SAFETY PRECAUTIONS

This safety alert symbol is used to call attention to a message intended to provide a reasonable degree of PERSONAL SAFETY for operators and other persons during the normal operation and servicing of this equipment.

DANGER – denotes immediate hazards which WILL result in severe personal injury or death.

WARNING – denotes a hazard or unsafe practice which COULD result in severe personal injury or death.

This manual uses two other words to highlight information. IMPORTANT calls attention to special mechanical information and NOTE: emphasizes general information worthy of special attention.

All operators and mechanics should read this manual, and be instructed about safe operating and maintenance procedures. If the operators or mechanics cannot read and understand English, it is the owner’s responsibility to explain this material to them.

This machine meets or exceeds the B-71.1-2003 specifications of the American National Standards Institute, in effect at the time of production. However, improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert ▲ symbol, which means DANGER or WARNING - “personal safety instructions.”

Failure to comply with the instructions may result in personal injury or death.

Incorrect usage of this machine may result in severe injury. Personnel operating and maintaining it should be trained in the proper use and should read the manuals completely and thoroughly before attempting to set-up, operate, adjust, or service this machine.

It is the owner’s responsibility to make certain that the operators and mechanics read and understand this manual and all decals before operating this machine. It is also the owner’s responsibility to make certain that the operators and mechanics are qualified and physically able individuals, properly trained in the operation of this equipment. All operators and mechanics must become familiar with the safe operation of the equipment, operator controls and safety signs.

Never let children or untrained people operate or service the equipment. Local regulations may restrict the age of the operator.

The owner/user can prevent and is responsible accidents or injuries occur-

ring to themselves, other people or property.

The owner should also ensure that the operator/mechanic know that they

are responsible for their own safety as well as the safety of other persons within the vicinity. Remember, the operator is responsible for accidents or hazards occurring to other people or their property.

Safety and Instruction Decals

▲ Specific safety warning decals are located on the equipment near the immediate areas of potential hazards. These decals should not be removed or obliter-

ated. Replace them if they become non-readable.

The following illustrations show the various decals that are located on the machine. A brief explanation, for those requiring one, is shown to help the operator understand the meanings of these decals.

Part Number

727016

Read Owner’s Manual and Quick Reference Decal before attempting to operate this machine.

Avoid skin contact with battery acid. Always wear eye protection when checking the battery, acid can cause serious injury to skin and eyes. If contact occurs, flush area with clean water and call physician immediately. Acid will also damage clothing. Do not allow open flame near the battery when charging. Hydrogen gas forms inside the battery. This gas is both toxic and flammable and may cause an explosion if exposed to flame. Always remov e the negativ e ground first and replace it last. Do not overfill battery. Electrolyte may overflow and damage paint, wiring or structure. When cleaning the battery, use soap and water. Be careful not to get soap and water into the battery. Use soda mixed in water to clean corrosion off the terminals.

Part Number

727420

Part Number

727438

Do not smoke while refueling. Do not fill tank with engine running, or while the engine is hot. Allow engine to cool before storing machine inside a building. Store away from open flame or spark if there is fuel in tank. Clean up any gasoline spills. Do not refuel while in enclosed trailer or other enclosed areas

Never operate the mower deck with side deflector damaged, altered, removed or in raised position, except when the entire grass catcher attachment or mulching system is being used.

Whirling blades! Keep hands and feet away. Beware of thrown objects.

601156_0308 7

While Operating

Neverperform maneuvers

at high groundspeeds .

Avoidsudden turns. Avoidquick movements of steering levers. Reduce speed and use extreme

caution when operating on slopes.

Checkmowing area, and remove objects

that could be thrownby blades.

BeforeLeaving Operating Platform

Place drive/steering

controlsin par k brakeposition.

Place deckclutch switch

in the offposition.

Turnengine off and remove key. Chockmachine when par kedon a slope.

793547

ReadOwner’s Manual

HelpAvoid Injury

Operatortraining required. Knowall controls.

Keepshields in place. Maintainall safety devices. Lookbehind before backing. Keepchildren and others away. Stayclear of power driven parts. Donot operate in areas where

machinecould tip.

BeforeStar ting

Steering levers mustbe in

park brakeposition.

Deckclutch switch must

be in offposition.

Checkperformance of all safety interlock switches daily (including operatorpresence switch).

Refueling

Stop engine and allow engine to cool for2 minutes prior to refueling.

Clean up anygasoline spills. Do not refuel while in enclosed

traileror other enclosed areas .

793570

Keep engine and pump compartment(s) clean (especially in exhaust area) to prevent fire and provide maximum engine and hydraulic cooling.

If you lose steering control while operating the machine, place the steering control levers in the park brake position immediately. Inspect the machine and

involve your Hustler dealer to resolve the problem before continuing to operate.

If pump belt fails, steering control will be lost. Refer to owner’s manual for inspection and replacement intervals and refer to above paragraph for emergency procedures.

Part Number

600899

Part Number

771436

Part Number

788968

If you loose steering control while operating the machine, place the steering

control levers in the park brake position immediately. Inspect the machine and

600899

involve your Hustler dealer to resolve the problem before continuing to operate.

If pump belt fails, steering control will be lost. Refer to owner’s manual for

inspection and replacement intervals and refer to above paragraph for emergency procedures.

Do not remove or modify stabilizer wheels or rear engine guard or injury can occur. Never stop suddenly while backing down slopes. This action may result in a reaction of the tractor that can cause serious physical injury.

Keep engine and pump compartment(s) clean (especially in exhaust area) to prevent fire and provide maximum engine and hydraulic cooling.

Never operate the mower deck with side deflector damaged, altered, removed or in raised position, except when the entire grass catcher attachment or mulching system is being used. Stay clear of mower blades as long as engine is running. Keep a safe distance from machine.

Keep shields or covers in place while machine is in operation. Keep hands away from rotating pulleys and belts. Whirling blades! Keep hands and feet away. Beware of thrown objects.

Never operate the mower deck with side deflector damaged, altered, removed or in raised position, except when the entire grass catcher attachment or mulching system is being used.

Stay clear of mower blades as long as

794297

engine is running. Beware of thrown objects.

Part Number

794297

Part Number

793570

Do not remove or modify stabilizer wheels or injury can occur. Keep a safe distance from machine. When operating on a slope (up to 15 degrees) be aware of any conditions that may cause the tractor drive tires to lose traction resulting in a possible loss of control of the machine.

Part Number

793547

Keep shields or covers in place while machine is in operation. Keep hands away from rotating pulleys and belts.

Part Number

727453

8 601156_0308

SLOPE GUIDE

Use this diagram when determining the degree of slope to be mowed.

Line B

E (15o)

D (10o)

C (5o)

Slope Guide Lines

Line A

1. Hold this sheet of paper in front of you. Make sure that Line A is horizontal.

2. Align Line B with a vertical surface such as pole, tree or building.

3. Fold the paper along the slope guide lines (C, D or E).

4. Align the closest slope guide line with the ground slope. This will give you a close estimation of the ground slope to be mowed.

601156_0308 9

10 601156_0308

OPERATION

Safe Operating Practices

This product is capable of amputating hands and feet and throwing

objects. Always follow all safety instructions to avoid serious injury or death.

Operation

▲ Evaluate the terrain to determine what accessories and attachments are

needed to properly and safely perform the job. Only use accessories and attachments approved by the manufacturer.

▲ Never leave a running machine unattended. Always stop on level

ground, disengage deck clutch, place steering control levers in park brake position, stop tractor engine, and remove ignition key before leaving operator’s seat for any reason including emptying the catcher or unclogging the chute.

▲ Do not change the engine governor setting or overspeed the engine. ▲ Always remain seated while operating machine. ▲ Always keep safety shields and covers in place, except for servicing. ▲ Always maintain a safe distance from people and pets when mowing.

Always stop machine if someone enters the area.

▲ Always operate machine in daylight or with adequate working lights. ▲ Follow daily and weekly checklists, making sure hoses are tightly

secured and bolts are tightened.

▲ Always observe traffic laws while driving machine from one location

to another. Watch for traffic when operating near or crossing roadways.

▲ Always be alert for hazards such as rocks, metal objects and other

debris which may be thrown or entangled by mower blades. Watch out for holes or deep depressions.

▲ Inspect area to be mowed for hazards such as rocks, metal objects and

other debris which may be thrown or entangled by mower blades. Remove these objects before mowing.

▲ Always inspect machine for damage after striking a foreign object. If

damage is found, repair machine immediately. Be sure to stop on level ground, disengage deck clutch, place steering control levers in park brake position, stop tractor engine, and remove ignition key when leaving operator’s seat to inspect damage.

▲ Always wear adequate ear protection, such as earplugs, when operat-

ing this equipment as prolonged exposure to uncomfortable or loud noises can cause impairment or loss of hearing. Do not wear radios or music headphones while operating the machinery. Safe operation requires your full attention.

▲ Do not operate the equipment while wearing sandals, tennis shoes,

sneakers, shorts or any type of loose fitting clothing. Long hair, loose clothing or jewelry may get tangled in moving parts. Always wear long pants, safety glasses, ear protection and safety shoes when operating this machine.

▲ Always be aware of what is behind the machine before backing up.

Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing up.

▲ Never push forward suddenly on your steering control levers while the

machine is in rearward motion because machine may tip backwards.

▲ Never pull back suddenly on your steering control levers while the

machine is in forward motion.

▲ When moving in reverse, push forward slowly on steering control

levers and avoid sudden movement. Rapid movement of the steering control levers in either direction could result in a reaction of the tractor that can cause serious injury.

▲ Never operate a poorly maintained machine. ▲ Never attempt high speed maneuvering, especially in crowded or con-

gested areas.

▲ Never allow persons to operate this machine without proper instruc-

tion or allow children to operate machine. Allow only responsible adults who are familiar with these instructions to operate this machine.

▲ Never put hands or feet under any part of the machine while it is run-

ning.

▲ Never carry passengers. ▲ Never direct discharged material toward anyone. Avoid discharging

material against a wall or obstruction. Material may ricochet back

toward the operator. Always disengage the blades and wait for them to stop before crossing gravel drives, walks or roads.

▲ Always keep clear of the mower blades and attachments during their

operation.

▲ Turn off blades when not mowing. ▲ Slow down before turning. ▲ Stop the engine before removing the grass catcher or unclogging the

discharge chute. Never clear the discharge chute with the engine running. Turn off the engine and be sure the blades have stopped before cleaning. Use a stick to clear a plugged discharge area. Never use

your hand!

▲ Do not operate the machine while under the influence of alcohol o r

drugs.

▲ Exercise caution when loading or unloading the machine onto a trailer

or truck.

▲ Always wear safety goggles or safety glasses with side shields when

operating the mower.

▲ Data indicates that operators, age 60 years and above, are involved in a

large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the mower safely enough to protect themselves and others from serious injury.

▲ Follow the manufacturer’s recommendation for wheel weights or

counterweights.

▲ If any attachment or additional weight is mounted on the rea r of the

unit, any rapid movement of the steering control levers in either direction could result in a reaction of the tractor that can cause serious injury.

▲ Clean flammable material from machine. Prevent fires by keep-

ing engine compartment, exhaust area, battery, fuel line, fuel tank and operator’s station clean of accumulated trash, grass clippings, and other debris. Always clean up spilled fuel and oil.

Using a ramp

▲ Use extreme caution when loading and unloading a unit onto a truck or

trailer with a ramp.

▲ Use only a single, full width ramp; do not use individual ramps for

each side of the unit. Having a full width ramp provides a surface for the tractor frame to contact if the unit starts to tip backwards. It also reduces the risk of a wheel going off and the machine tipping over.

▲ Do not exceed a 15 degree angle between the ramp and the ground or

between the ramp and the trailer or truck.

▲ When on a ramp avoid sudden acceleration

Slope Operation

Slopes are a major factor in loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it; do not mow it. REMINDER: Only operate on slopes of 15 degrees or less.

▲ Use extreme caution when operating on slopes.

• Be extremely careful changing directions on a slope. Slow down.

• Do not operate where the machine could slip or tip.

• Turn slowly

• Turn on the most level part of the slope

• To maximize traction, it is better to turn the front of the machine

uphill, rather than downhill. If drive tires lose traction, steering

control is lost which could cause serious injury or death.

• If it becomes necessary to turn downhill, turn slowly and gradually, if possible.

▲ Do not remove or modify the stabilizer wheels. ▲ Watch for holes, ruts, bumps, rocks or other hidden objects. Uneven

terrain could overturn the machine. Tall grass can hide obstacles.

▲ Remove obstacles such as rocks, tree limbs, etc. ▲ Keep all movement on slopes slow and gradual. Do not make sudden

changes in speed or direction.

▲ Avoid startin g and stopping on a slo pe. If tires lose traction, disengage

the blades and proceed slowly straight down the slope.

▲ Mow a safe distance (minimum of 10 feet) away from drop-offs,

retaining walls, drainage ditches, embankments, water, and other types

601156_0308 11

of hazards to avoid a wheel dropping over the edge or to avoid the ground from breaking away. This will reduce the risk of the machine suddenly rolling over causing serious injury or death.

▲ Use a walk behind, push mower or hand-held trimmer on slopes and

near drop-offs, retaining walls, drainage ditches, embankments and water to avoid machine rollover and serious injury or death.

▲ Do not mow on wet grass. Reduced traction could cause sliding and

loss of steering control.

▲ Do not tow on slopes. The weight of the towed equipment may cause

loss of traction and control.

▲ Do not try to stabilize the machine by putting your foot on the ground. ▲ If the mower’s tires lose traction when operating on slopes, disengage

the blades, place the steering control levers in the park brake position, turn the engine off and get help.

▲ Never make sudden starts, stops, turns, or reverse direction, especially

when maneuvering on slopes. The steering is designed for sensitive response. Rapid movement of the steering control levers in either direction could result in a reaction of the tractor that can cause serious injury.

▲ Never stop suddenly while backing down slopes. This action may

result in a reaction of the tractor that can cause serious physical injury.

▲ The Hustler mower is capable of operating horizontally (traver se) on

moderately steep slopes. When operating on slopes up to 15 degrees, be aware of any conditions that may cause the tractor drive tires to lose traction resulting in a possible loss of control of the machine. An operator should not operate on a slope until he is thoroughly familiar with the equipment.

Do not operate on slopes greater than 15 degrees.

Refer to Slope Guide, page 9, when determining the degree of slope

to be mowed.

It is strongly recommended that the operator drive the machine off of the slope, using extreme caution, if any sign of loss of traction is detected. Wait until the condition that caused the problem is resolved before attempting to operate on the slope again.

Terrain conditions can affect traction resulting in possible loss of control of the machine. Some of the conditions to be aware of are:

1. Wet terrain

2. Depressions in the ground; i.e. holes, ruts, washouts

3. Mounds of dirt

4. Soil type; i.e. sand, loose dirt, gravel, clay

5. Grass type, density, and height

6. Extremely dry conditions of grass

7. Tire pressure

The attachments mounted to the tractor will also affect the way it handles on a slope. Be aware that each attachment’s characteristics vary.

Another consideration to safe mowing on slopes is to be aware of what is located at the bottom of the slope. Extreme caution should be used when there is a hazard located at the bottom of the slope. Some examples are:

1. Water; i.e. lake, river

2. Cliffs, retaining walls

3. Roads, highways

4. Buildings

5. Rocks

These are just a few examples of situations when caution must be used when operating on a slope. There are many other possibilities too numerous to mention. Just remember to always exercise extreme caution when operating on any slope.

Children

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.

▲ Never leave machine unattended with ignition key in switch, espe-

cially with children present.

▲ Children or bystanders may be injured if they move or attempt to oper-

ate the tractor while it is unattended. Always disengage deck clutch, place steering control levers in park brake position, stop tractor engine, and remove ignition key when leaving operator’s seat.

▲ Keep children out of the mowing area and under the watchful care of a

responsible adult other than the operator.

▲ Be alert and turn the machine off if children enter the area.

▲ Before and while backing, look behind and down for small children.

▲ Never carry children, even with the blades off. They may fall off and

be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine.

▲ Never allow children to operate the machine.

▲ Use care when approaching blind corners, shrubs, trees, the end of a

fence or other objects that may obscure vision.

▲ Never allow children or others in or on towed equipment.

Control Panel

IMPORTANT: When access is required under the seat platform and the

seat is equipped with the optional arm rests, make certain to place the control arms in the park brake position and pivot the arm rests upward before placing the seat platform in the full forward position to prevent arm rest damage.

Control Panel

A. Choke control (Fig. 3-1) — a cable is linked to manually operate the

engine choke. When the control knob is in the down position, the choke is in the off (run) position. When the control knob is pulled up, the choke is in the on (start) position. Do not operate the machine in the on (start) position.

B. Throttle control (Fig. 3-1) — a cable is linked to engine throttle for con-

trolling engine speed. Move lever forward to increase engine rpm, move lever rearward to decrease engine rpm.

C. Deck clutch switch (Fig. 3-1) — this switch engages the deck. Pull the

switch up to engage and push switch down to disengage the clutch. IMPORTANT: Never engage clutch with engine running at high rpm or when the deck is under load. Clutch, belts or deck could be damaged.

D. Ignition switch (Fig. 3-1) — a three position switch: off, run, and start.

With key inserted, rotate it clockwise to START position; release key when engine starts, and switch will automatically return to the RUN position.

E. Oil pressure light (Fig. 3-1) — this light comes on when the ignition

switch is placed in the RUN position and stays lit until the engine is run-

ning and a safe oil pressure is developed. If light comes on during operation, shut engine off immediately and locate and correct the problem.

F. 20 amp fuse (Fig. 3-1) — Main - 20 amp, blade-type G. 10 amp fuse (Fig. 3-1) — Clutch/Aux - 10 amp, blade-type

Controls

A. Steering control levers (Fig. 3-2 & 3-3) — these levers control the trac-

tor’s speed, direction, stopping, neutral lock, and park brake. Levers are used to steer, accelerate, decelerate, stop and change direction. When the control levers are in the park brake position (3-3) the tractor will not move when the engine is on and drive pumps are operating.

WARNING: The parking brake may not hold the tractor if parked on a slope. Block or chock the machine when parked on a slope

B. Deck lift pedal (Fig. 3-4) — the deck lift pedal is used to raise or lower

the deck. Push on the pedal to raise the deck and then place the deck height locking pin into the desired cutting height hole. Push the deck lift pedal to raise the deck when going over obstructions.

Safety start interlock system

The tractor is equipped with a safety start interlock system consisting of

the park brake switches, seat switch, and deck clutch switch.

Check tractor safety start interlock system daily, prior to operation.

This system is an important tractor safety feature. It should be repaired

12 601156_0308

Steering control levers in

park brake position

A -Choke E - Oil pressure light B -Throttle F - 20 amp fuse C - Deck clutch switch G - 10 amp fuse D - Ignition switch

Figure 3-1

Steering control lever

Deck lift pedal

Figure 3-3

Shown with steering control

levers in neutral position

Figure 3-2

immediately if it malfunctions. The machine incorporates a separate seat switch which will stop the tractor engine when the operator is unseated for any reason while the tractor is operating. This is a safety feature designed to prevent runaway or accidental entanglement. To inspect the system:

1. The operator must be on the seat when testing the seat switch.

2. Set both steering control levers in the park brake position.

3. Start the engine and allow it to warm up to operating temperature.

4. With the deck clutch switch down and the steering control levers in the park brake position, slowly raise off of the seat. The engine should continue to run.

5. With the deck clutch switch up and/or the steering control levers in the neutral, forward or reverse position, slowly raise off of the seat. The engine should stop.

6. If the engine fails to stop when the deck clutch switch is up or one or

both of the steering control levers are up and the operator is off the seat, check the function of the seat switch. If the seat switch is not operating properly (is not opening or closing) and if the cause can not be determined, replace the seat switch. If the problem can not be located, contact your Hustler Dealer.

Figure 3-4

WARNING: The safety interlock system should always func-

tion per steps 4 and 5. If it does not function properly, it should be corrected immediately. Do not operate machine without properly functioning seat safety switch.

Engine starting

The tractor’s safety start interlock system is also designed to protect the operator and others from accidental injury due to unintentional engine starting. The engine starting motor will not engage until:

A. Steering control levers are in the park brake position. B. Deck clutch switch is in the down (OFF) position.

WARNING: The safety interlock system must not be disconnected or bypassed. Doing so could cause the machine to operate unexpectedly resulting in personal injury.

NOTE: The operator’s seat is equipped with a separate safety switch. If for any reason the operator should become unseated when the steering control levers are not in the park brake position (park brake switches are disengaged) or the deck clutch switch is engaged the engine will stop.

The following steps are the correct procedures for starting the engine. If difficulty is encountered, contact the Hustler Dealer in your area.

1. Before starting tractor each day, perform daily pre-operation checking.

(See Safety start interlock system section)

2. Make sure the steering control levers are in the park brake position and

deck clutch switch is disengaged. Only start the engine from the opera-

tor’s position.

3. Use choke, if unit is equipped with one, when engine is cold, or if warm

engine fails to start within 5 seconds of cranking. Avoid flooding and

operate engine without choking as soon as possible.

4. Set throttle at approximately 1/2 open position.

601156_0308 13

Mini FasTrak 36/42

Slot

Bypass valve rod

(Left rod shown)

(Viewed from the rear left underneath side)

Figure 3-5

Stopping the engine

Use the following procedure to shut off the engine after operating the equipment.

1. Place the steering control levers in the park brake position

2. Disengage the deck clutch

3. Throttle back to low idle for a couple of minutes

4. Rotate ignition key counter-clockwise to the OFF position. Remove the

key from switch before leaving the tractor.

Moving tractor with stalled engine

If it becomes necessary to move the tractor when the engine is inoperative, the transaxles are equipped with bypass valves.

FasTrak 36/42 (Mini FasTrak 36/42) - Before moving the unit, pull out on the bypass valve rods and slide them into the slot to lock in position. Both bypass valve rods are located underneath the rear of the tractor at the back of the transaxle. (Fig. 3-5)

FasTrak 48 /54 - Before moving the unit, pull up on the bypass valve rod and slide it in the slot to the disengaged position.

The steering control levers must be placed in the neutral position, to release the park brakes, so that the tractor can be moved. Bo th by pass valv e rods are located at the front corners of the engine on the engine platform. Fig. 3-6

Do not tow the machine. Move it by hand or use a winch to load on a trailer for transporting.

When transporting on another vehicle, the tractor must be secured.

IMPORTANT: Always make certain the two bypass valves are r eturn ed to their operating position before running the tractor following repairs.

FasTrak 48/54

Bypass valve rod

(Left rod shown)

Bypass valve rod shown in towing position

Figure 3-6

5. Insert key in ignition switch and rotate full clockwise to engage starting

motor. Release key when engine starts. IMPORTANT: The engine starter should not be operated for periods

longer than 30 seconds at a time. An interval of at least two minutes should be allowed between such cranking periods to protect the starter from overheating and burn-out.

6. Perform test to make sure safety start interlock system is operating prop-

erly. Refer to Safety start interlock system section.

7. As soon as engine begins to run, check to make certain the oil warning

light, engine light and alternator warning light (if applicable) are off. If not, stop engine immediately and check for the cause.

8. Allow the engine to idle a few minutes before advancing the throttle and/

or engaging the deck clutch.

9. Before stopping the engine, place the steering control levers in the park

brake position, disengage the deck clutch, and throttle back to low idle for a couple of minutes; then rotate ignition key counter-clockwise to the OFF position. Remove the key from switch before leaving the tractor.

WARNING: Allow engine exhaust manifold to cool before engaging or disengaging the bypass valves. The bypass valve rods are located close to the exhaust system.

Driving the tractor

DANGER: Never make sudden stops or reverse direction,

especially when maneuvering on a slope. The steering is designed for sensitive response. Rapid movement of the steering control levers in either direction could result in a reaction of the tractor that can cause serious injury.

After starting engine, engage the control levers and steer as follows:

To go forward, push steering control levers forward an equal distance (Fig. 3-7).

To go in reverse, pull steering control levers rearward an equal distance (Fig. 3-7).

To turn left, move the right steering control lever farther forwar d from neutral than the left steering control lever.(Fig. 3-7)

To turn right, move the left steering control lever farther fo rward from neutral than the right steering control lever. (Fig. 3-7)

“0” degree turn, move one steering control lever forward and the other steering control lever back of neutral. This will allow the drive wheels to counter-rotate. (Fig. 3-7)

To stop or decrease speed, move steering control levers to neutral. When going forward pull back gently on steering control levers. When going in reverse push forward gently on steering control levers.

For emergency stop, when traveling forward or rearward, place the steering control levers in the park brake position immediately.

DANGER: When moving in the rearward direction push forward gently on steering control levers and avoid sudden movement. Any sudden movement could cause the front of the mower to come off of the ground resulting in possible loss of control causing serious injury or death.

To make a three point turn to the right, move the left steering control lever farther forward from neutral than the right steerin g control lever and start the turn. Next, pull back on the steering control levers until they are past neutral and the machine starts to go rearward. Pull right steering control lever farther rearward from neutral than the left stee ring control lever until the rear of the machine has pivoted around. Then, push the steering control levers forward until they are both past neutral and the machine starts to go

14 601156_0308

FRONT OF TRACTOR FACES THIS DIRECTION

N N

FORWARD TRAVEL ZERO DEGREE

TURN

N = NEUTRAL POSITION Direction of arrows indicate direction of tractor movement

forward. Push the left steering control lever farth er forward from neutral than the right steering control lever and finish the turn. (Fig. 3-9)

WARNING: Always be aware of what is behind the machine before backing up. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing up.

IMPORTANT: Rapid movement of s teering control lever s is not r ecom-

mended as damage to the hydraulic system components may occur.

To increase speed, increase steering control lever’s distance from neu-

tral. The farther forward steering control levers are from neutral, the faster tractor will travel forward. The farther back steering control levers are from neutral, the faster tractor will go in reverse.

FORWARD TRAVEL

RIGHT TURN

Figure 3-7

Operating suggestions

DANGER: Prior to operating the tractor the operator should

be thoroughly familiar with the proper use and operation of the equipment, should read the manual completely and thoroughly, and should have attempted slow moving maneuvers to become familiar with the operation of the equipment before attempting normal speed operation. An inexperienced opera tor s houl d not mow on slopes or on uneven terrain.

WARNING: If you lose steering control while operating the machine, place the steering control levers in the park brake position immediately. Inspect the machine and involve your Hustler dealer to resolve the problem before continuing to operate.

REVERSE TRAVEL

RIGHT TURN

until the wheel clears and then pivot the opposite wheel around.

When turning on soft wet turf, keep both wheels rolling either forward or backward. Pivoting on one stopped wheel can damage turf. This is especially important when mowing.

Tractor performance is maximum when the throttle is set at full rpm. This gives maximum power to the drive wheels and deck when needed. Use the control levers to control ground speed rather than engine rpm.

Keep blades sharp. Many professional mowing companies have additional sets of blades and change blades twice a day: once in the morning and again at noon. Many problems with incorrect cutting patterns are due to dull blades or blades which have been sharpened incorrectly. Information on sharpening blades is listed in this manual’s maintenance section. In addition, most communities have individuals or companies which specialize in sharpening mower blades. Blade sharpness should be checked daily.

DANGER: Never work with blades while engine is running or deck clutch switch is engaged (on). Always place deck clutch switch in the disengaged position, place steering control levers in the park brake position and turn engine off and disconnect negative battery cable. Block up mower when you must work under it. Wear gloves when handling blades. Always check for blade damage if mower strikes rock, branch or other foreign object during mowing!

REVERSE TRAVEL

WARNING: The unit’s steering control levers are very

responsive: Easy does it! For smooth operation, move lever slowly, avoid sudden movement. Skill and ease of operation come with practice and experience. The machine can spin very rapidly. Use caution when making turns and slow down before making sharp turns.

Inexperienced operators may have a tendency to oversteer and lose control. Slow-moving practice maneuvers are recommended to become familiar with these characteristics before attempting normal speed operation.

WARNING: Sharp depressions or raised obstacles (such as gutters or curbs) should not be directly approached at high speed in an attempt to “jump” them as the operator could be thrown from the equipment. Approach at a slow speed and angle one drive wheel at the obstruction. Continue at an angle

601156_0308 15

Side

discharge

chute

Figure 3-8

Three point turn

Step 1

Step 2

Step 3

Use high blade speed. Your mower is designed to operate at full throt-

tle. The throttle setting directly controls blade speed. The highest blade speed generally gives best cut.

Direct grass discharge to right, away from unmown area. Select a

mowing pattern that directs grass discharge towards the outside, not towards center, of mowing area. Generally, this means using a pattern utilizing left turns because side discharge is to right. In any case, avoid throwing grass discharge onto unmowed area because grass is then mowed “twice”. Mowing twice puts an unnecessary load on the unit and reduces mowing efficiency.

When mowing a lawn for the first time cut grass slightly longer than

normal to avoid scalping uneven terrain. When possible, it is best to use the cutting height that was used in the past. When cutting grass taller than six inches, you may want to mow the lawn twice to achieve a better quality of cut.

During normal mowing cut only about 1/3 of the grass blade. Cutting

more than that is not recommended unless grass is sparse or it is the end of the mowing season.

Alternate mowing direction to keep the grass growing straight and bet-

ter dispersion of the clippings.

Remember, grass grows at different rates at different time of the year.

Mow more often in the early spring to maintain the same cutting height. As the growth rate slows in mid summer, mow less frequently. If you cannot mow at a regular interval, mow at a high cutting height; then mow again two days later at a lower cutting height.

Raise the cutting height of the mower if the cutting width of the mower

is wider than the previous mower. This ensures that uneven turf is not cut too short.

Raise the cutting height of the mower if the grass if slightly taller than

normal or if it contains a high degree of moisture. Then mow it again with the cutting height set lower.

If the machine’s forward motion must be stopped while mowing, a

clump of grass clippings may drop onto your lawn. To avoid this, move onto a previously cut area with the blades engaged.

WARNING: Never direct discharge of material from mower deck towards bystanders. Do not operate the mower without either the discharge chute or the entire grass collection system in place. Fig. 3-8

Mower deck operation

DANGER: Never attempt to make any adjustments to the

Figure 3-9

Stop handle

16 601156_0308

mower deck while the engine is running or with the deck drive clutch engaged. Mower blades cannot be seen and are located very close to deck housing. Fingers and toes can be cut off instantly.

Height

adjusting

stop

Figure 3-10

With the engine running, engage the deck clutch switch (Fig. 3-1) and advance engine throttle to full rpm.

NOTE: Engaging the deck clutch at high engine rpm or when under heavy load (in tall grass for example) can cause belts and/or electric clutch to slip, resulting in premature wear or possible damage.

Deck cutting height adjustment

Deck height is adjustable from 1-1/2”- 4-1/2” (3.81 cm - 11.43 cm) in 1/4” (.64 cm) increments. The holes in the height adjusting bar are spaced at 1/2” (1.27 cm) intervals. By turning the height adjusting stop around, 1/4” (.64 cm) increments can be attained due to the 1/4” (.64 cm) plate that is part of the stop. Fig. 3-10

EXAMPLE: When the height adjusting stop is placed in the 1-1/2” (3.81 cm) hole, with the 1/4” (.64 cm) plate facing to the front of the unit, the cutting height is at 1-1/2” (3.81 cm). When the height adjusting stop is placed in the 1-1/2” (3.81 cm) hole, with the 1/4” (.64 cm) plate on the operator’s

side of the hole, the cutting height is at 1-3/4” (4.45 cm).

The notch located at the rear of the height adjusting bar is to be used

when the deck is placed in the transport mode.

Anti-scalp wheels

Anti-scalp wheel kits are standard on FasTrak units. These anti-scalp wheels are designed to minimize scalping when mowing on rough uneven terrain.

After setting the cutting height, adjust the anti-scalp wheels so they extend below the deck but do not contact the ground. They should always be at least 1/4” to 3/4” (6.35mm to 19.05mm) below the deck. With the unit sitting on a flat level surface, the wheel position can be adjusted up or down as needed from 3/4” to 1-3/4” (19.05mm to 44.45mm) below the blade surface. Move the wheels up or down, in 1/2” (12.70mm) increments, using the different axle mount holes in the wheel mount bracket. Fig. 3-11

When adjusting the rear anti-scalp wheels, the wheel should be in the same axle mount hole as the front anti-scalp wheels.

Anti-scalp wheel

Adjusting holes

Figure 3-11

601156_0308 17

18 601156_0308

MAINTENANCE & ADJUSTMENTS

Safe Servicing Practices

This product is capable of amputating hands and feet and throwing objects. Always follow all safety instructions to avoid serious injury or death.

Service

▲ Unless specifically required, DO NOT have engine running when ser-

vicing or making adjustments to tractor. Park the machine on level ground. Place steering control levers in the park brake position, disengage deck clutch, lower deck, remove ignition switch key and disconnect negative battery cable before doing any maintenance. Wait for all movement to stop before adjusting, cleaning or repairing. Repairs or maintenance requiring engine power should be performed by trained maintenance personnel only. To prevent carbon monoxide poisoning, be sure proper ventilation is available when engine must be operated in an enclosed area. Read and observe safety warnings in front of manual.

▲ Before working on or under the deck, make certain engine cannot be

accidentally started. Shut engine off and remove ignition switch key for maximum safety. Repairs or maintenance requiring engine power should be performed by trained maintenance personnel only.

▲ Except when changing or checking belt, always keep belt covers on

mower deck for safety as well as cleanliness.

▲ Use a stick or similar instrument to clean under the mower making

sure that no part of the body, especially arms and hands are under mower.

▲ Keep your machine clean and remove any deposits of trash and clip-

pings, which can cause engine fires and hydraulic overheating as well as excessive belt wear. Clean up oil or fuel spillage. Allow machine to cool before storing.

▲ Clean flammable material from machine. Prevent fires by keep-

ing the top of the deck, engine compartment, exhaust area, battery, hydraulic lines, fuel line, fuel tank and operator’s station clean of accumulated trash, grass clippings, and other debris. Always clean up spilled fuel and oil.

▲ Always wear adequate eye protection when servicing the hydraulic

system and battery, or when grinding mower blades and removing accumulated debris.

▲ Use extra caution when handling gasoline and other fuels. They are

flammable and vapors are explosive.

▲ Never attempt to start engine when there is a strong odor of gasoline

fumes present. Locate and correct cause.

▲ Never remove fuel cap or refuel tractor while engine is running; never

refuel near an open flame or near devices which can create a spark. Refuel outdoors. Never refuel or drain the fuel from the machine indoors.

▲ Never run the engine in an enclosed area unless exhaust is vented to

the outside. Exhaust gases contain carbon monoxide which is odorless and deadly poison.

▲ Never attempt to make any adjustments or repairs to the tractor drive

system, mower deck or any attachment while the tractor engine is running or deck clutch is engaged. Repairs or maintenance requiring engine power should be performed by trained maintenance personnel only.

▲ Never work under the machine or attachment unless it is safely sup-

ported with jack stands. Make certain machine is secure when it is raised and placed on the jack stands. The jack stands should not allow the machine to move when the engine is running and the drive wheels are rotating. Use only certified jack stands. Use only appropriate jack stands, with a minimum weight rating of 2000 pounds to block the unit up. Use in pairs only. Follow the instructions supplied with the vehicle stands.

▲ Do not touch hot parts of machine.

▲ Keep nuts and bolts tight, especially the blade attachment bolts. Keep

equipment in good working condition.

▲ Never tamper with safety devices. Check their proper operation regu-

larly.

▲ Stop the engine before removing the grass catcher or unclogging the

your hand!

▲ Grass collection system components are subject to wear, damage and

deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer’s recommended parts, when necessary.

▲ Exercise caution when working under the deck as the mower blades

are extremely sharp. Wrap the blade(s) or wear gloves and use extra caution when servicing them.

▲ Use only genuine Hustler replacement parts to ensure that original

standards are maintained

Introduction

Regular maintenance is the best prevention for costly downtime or expensive, premature repair. The following pages contain suggested maintenance information and schedules which the operator should follow on a routine basis. For more detailed information order the correct pa rts manual for your unit. Refer to the Product Literature section of this manual.

Remain alert for unusual noises, they could be signaling a problem. Visually inspect the machine for any abnormal wear or damage. A good time to detect potential problems is while performing scheduled maintenance service. Correcting the problem as quickly as possible is the best insurance.

Clear away heavy build-up of grease, oil and dirt, especially in the engine and under the seat platform areas; minute dust particle are abrasive to closetolerance engine and hydraulic assemblies.

Daily inspect mower for grass clippings and wire and string tangles. The underside of the mower deck will collect a build-up of grass clippings and dirt, especially when grass is wet or has high moisture content. This build-up will harden, restricting blade and air movement and will probably show a poorer quality of cutting. Therefore it should be removed routinely.

To do this it will be necessary to raise and block the deck, using jack stands or blocks, in the full up position and scrape the build-up from underneath.

Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel. Consult your Hustler service center when assistance is needed.

Torque values

WARNING: Particular attention must be given to tightening

the drive wheel lug nuts and blade spindle bolts. Failure to correctly torque these items may result in the loss of a wheel or blade, which can cause serious damage or personal injury.

Torque values are given below:

Ft-lbs. Nm

Wheel (lug) nuts.................................................65-75............88.14-101.7

Blade spindle bolt top ..........................................118.................. 160.01

Blade spindle bolt bottom ....................................118..................160.01

Lug nuts only - It is recommended that these be checked after the first 2 hours of operation, initially, every 50 hours and following removal for repair or replacement.

For all other torques refer to the various tractor parts manuals for standard torque chart. See the Product Literature section of this manaul for ordering information.

For engine torque values, see engine owner’s manual.

Tires

It is important for level mowing that the tires have the same amount of air pressure. The recommended pressure are:

Drive wheels.................................... ................ 8-12 psi (55-83 KPa)

Gauge wheels.......................... ......................... 8-12 psi (55- 83 KPa )

601156_0308 19

Solid fill tires are not recommended for Hustler turf equipment. On

any machine, with solid filled tires, the warranty claim will be denied.

Lubrication

Use SAE multi-purpose grease.

Electrical system

The electrical system is a 12-volt, negative ground. Recommended battery size is a garden tractor BCI group U1R with 225 or better cranking AMP rating. A maintenance-free battery is recommended. Otherwise, follow battery manufacturer’s maintenance, safety, storing and charging specifications.

WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

WARNING: Change batteries in an open well ventilated area, away from spark and flames. Unplug charger before connecting or disconnecting from the battery . Wear protective clothing and use insulated tools.

WARNING: Avoid skin and clothing contact with battery acid. Always wear eye protection when checking the battery, acid can cause serious injury to skin and eyes. If contact occurs, flush area with clean water and call physician immediately. Acid will also damage clothing. Do not drink the battery electrolyte. Do not allow open flame near the battery when charging. Hydrogen gas forms inside the battery. This gas is both toxic and flammable and may cause an explosion if exposed to flame. Always remove the negative ground first and replace it last. Do not overfill battery. Electrolyte may overflow and damage paint, wiring or structure. When cleaning the battery, use soap and water. Be careful not to get soap and water into the battery. Clean the battery terminals with a solution of four parts water and one part baking soda when they become corroded.

WARNING: Shorts caused by battery terminals or metal tools touching metal tractor components can cause sparks. Sparks can cause a battery gas explosion which will result in personal injury. Prevent the battery terminals from touching any metal tractor parts when removing or installing the battery . Do not allow metal tools to short between the battery terminals and metal tractor parts.

WARNING: Incorrect battery cable routing could c ause damage to the tractor and battery cables. This can cause sparks which can cause a battery gas explosion which will result in personal injury. Always disconnect the negative (black) battery cable(s) before disconnecting the positive (red) cable(s). Always connect the positive (red) battery cable(s) before connecting the negative (black) cable(s).

Hydraulic system

The FasTrak 48/54 is equipped with two Hydro-Gear ZT 2800 transaxles. Fig. 4-1

IMPORTANT: Never use hydraulic or automatic transmission fluid in this system; use only motor oil as specified. Remember, dirt is the primary enemy of any hydraulic system.

The hydraulic expansion tank is located in front of the engine and under the operator’s platform. Fig. 4-1

Check oil level in hydraulic system after every 50 hours of operation or weekly, whichever occurs first. Check more often if system appears to be leaking or otherwise malfunctioning.

ZT 2800 transaxle

Expansion

tank

FasTrak 48/54 shown

Figure 5-1

ZT 2800 Filter

Figure 5-2

Fluid level should be at the “Full Cold” line on the expansion tank. Use

only SAE 20W50 SL service motor oil.

Initial system oil and filter change must be after the first 75 hours of use

or 1 year whichever comes first. Thereafter, replace filter and oil in each transaxle every 2 years or 200 hours, whichever comes first. NOTE: The fil- ter guard must be removed to access filter.

Each transaxle’s filter is located per Fig. 4-2. A standard oil filter wrench

is used to change filter, threads are right handed. Use a Hustler approved filter element only.

IMPORTANT: Purging procedures must be followed after changing the

oil and filter. Refer to Parts Manual (Hustler P/n 108277) for more detailed oil changing and purging information.

WARNING: When washing the mower, direct the spray away (especially if using a power washer) from the Hydro-Gear ZT 2800 transaxle’s seals to prevent water intrusion and to ensure component performance.

The FasTrak 36/42 (Mini FasTrak 36/42) is equipped with two

Hydro-Gear EZT integrated pump/motor transmissions. Fig. 4-3

The EZT integrated pump/motor transmissions are sealed for life and do

not require any scheduled service.

WARNING: When washing the mower, direct the spray away (especially if using a power washer) from the Hydro-Gear EZT transmission’s seals to prevent water intrusion and to ensure component performance.

20 601156_0308

EZT Integrated

pump/motor

FasTrak 48/54 shown

Closed

position

FasTrak 36/42 shown

Figure 5-3

Fuel system

DANGER: Observe usual fuel handling precautions:

Do not smoke while refueling. Extinguish all cigarettes, cigars, pipes andother sources of ignition. Do not remove fuel cap or fill tank with engine running or while engine is hot. Clean up any gasoline spills. Allow engine to cool before storing machine inside a building. Keep fuel away from open flame or spark and store machine away from open flame or spark or pilot light such as on a water heater or other appliances. Use extreme care when handling gasoline and other fuels. They are extremely flammable and vapors are explosive. A fire or explosion from gasoline can burn you and others and can damage property. Never refuel or drain the fuel from the machine indoors. Never attempt to start engine when there is a strong odor of gasoline fumes present. Locate and correct cause. Store gasoline in an approved container and keep it out of the reach of children. Never buy more than a 30 day supply of gasoline. Always place gasoline containers on the ground away from your vehicle before filling. Do not fill gasoline containers inside a vehicle or on a truck or trailer bed with interior carpets or plastic truck bed liners. Always place gasoline containers on the ground away from your vehicle before filling. When practical, remove gas-powered equipment from the truck or trailer and refuel the equipment with its wheels on the ground. If this is not possible, then refuel such equipment on the truck or trailer using a portable container and not a gasoline dispenser nozzle. If a gasoline dispenser nozzle must be used, keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device. Read and observe safety precautions elsewhere in this manual.

WARNING: Gasoline is harmful or fatal if swallowed. Long-term exposure to vapors can cause serious injury and illness. Avoid prolonged breathing of vapors. Keep face away from nozzle and gas tank or fuel container opening. Keep gas away from eyes and skin. If fuel is spilled on clothing, change clothing immediately.

The fuel tanks are located in the tractor’s fenders. Use regular unleaded gasoline with an octane rating of 87 or higher.

IMPORTANT: Never use methanol, gasoline containing methanol, or gaso-

Left fuel tank

position

Figure 5-4

Oil drain valve

Figure 5-5

hol containing more than 10% ethanol because the fuel system could be damaged. Do not mix oil with gasoline.

A fuel shut-off valve is located on each tractor. The location and opera-

tion of the fuel valve will vary depending upon the unit. Close the fuel valve to prevent fuel flow to the engine. The valve’s two other positions will allow fuel to be drawn from either one or the other fuel tank. 4-4

IMPORTANT: Do not overfill the fuel tanks. The fuel tanks should be

filled no higher than 2” (5.08 cm) below the tank’s fill neck.

Right fuel

tank position

Oil drain hose

Engine oil and filter

Check engine oil daily and after every 4 hours of operation. Tractor must be setting level when checking oil. Refer to engine manual and maintenance schedule for oil recommendation and capacities.

Change the engine oil and filter after the first 5 hours of operation, per the engine manufacturer’s recommendations after that. If tractor is being operated in extremely dirty conditions, then it is recommended oil be changed more frequently. IMPORTANT: When removing the oil filter take precau- tions to minimize oil spillage on the exhaust system.

Attach the oil drain hose, furnished with the unit, to the oil drain valve when draining the engine oil. Oil drain hose must be removed after oil is drained. IMPORTANT: All oil drips or spills must be cleaned off of the exhaust system before operating the machine. Fig. 4-5

Engine air filter

Perform engine air filter maintenance per the engine’s owner’s manual.

601156_0308 21

Cutting Plane

Cutting edge

Twisted Blade Edge

Cutting edge

(replace)

Do not sharpen to original pattern (below). It is easier to get a straight cutting edge following the resharpening pattern show above.

Original edge

Figure 5-6

Warped Blade (Replace)

Comparison of Warped and Straight Blades

Resharpening

pattern

Cutting

plane

Straight Blade Edge

End view of blades, comparing

twisted and straightened blades

Figure 5-8

Inspect the belt pulley grooves and flanges for wear. A new belt, or one in good condition, should never run against the bottom of the groove. Replace the pulley when this is the case, otherwise belt will lose power and slip excessively.

Never pry a belt to get it on a pulley as this will cut or damage the fibers of the belt covering.

Keep oil and grease away from belts, and never use belt dressings. Any of these will destroy the belt composition in a very short time.

Mower blade maintenance

Check the mower blades daily, they are the key to power efficiency and well groomed turf. Keep them sharp, a dull blade will tear rather than cut the grass, leaving a brown ragged top on the grass within a few hours. A dull blade also requires more power from the engine.

Replace any blade which is bent, cracked or broken.

WARNING: Never attempt to straighten a bent blade by heating, or weld a cracked or broken blade as the blade may break and cause serious injury. Replace worn or damaged blades.

DANGER: Never work with blades while engine is running or deck clutch switch is engaged (on). Always place deck clutch switch in the disengaged position, place steering control levers in the park brake position and turn engine off and disconnect negative battery cable. Block up mower when you must work under it. W ear gloves when handling blades. Always check for blade damage if mower strikes rock, branch or other foreign object during mowing!

Figure 5-7

General engine maintenance

Detailed instructions and recommendations for break-in and regular maintenance are specified in the Engine Owner’s manual. Please refer to this manual for engine servicing, lubricating oil levels with quality and viscosity recommendations, bolt torques, etc. The engine warranty is backed by the manufacturer. Special attention should be paid to applicable data which will not be duplicated here.

Belts

Inspect belts frequently for wear and serviceability. Replace a belt that shows signs of severe cuts, tears, separation, weather checking and cracking, or burns caused by slipping. Slight raveling of belt covering does not indicate failure, trim ravelings with a sharp knife.

WARNING: If the pump belt fails, loss of control will occur especially when operating on a slope. If you lose steering con-

trol while operating the machine, place the steering control levers in the park brake position immediately. Inspect the machine and involve your Hustler dealer to resolve the problem before continuing to operate.

WARNING: Always wear adequate eye protection when gr inding mower blades.

Always place deck clutch switch in the disengaged position, place steer-

ing control levers in the park brake position and turn engine off and disconnect negative battery cable. Block up mower when you must work unde r it. Wear gloves when handling blades. Always check for blade damage if mower strikes rock, branch or other foreign object during mowing!

Mower blade removal

Use a 15/16" wrench to remove the 5/8" cap screw holding the blade to

the spindle shaft from underneath. NOTE: A blade holding tool (part number

381442) is available from Hustler Turf Equipment. It is designed to prevent the blades from rotating when they are being removed or installed on the spindle. Contact your Hustler dealer for more information.

Sharpen the blades on a grinder f ollowing pattern as shown (Fig. 4-6).

Touch-up sharpening can be done with a file.

Check the blades for balance following grinding. A commercial balancing tool is available through most hardware supply stores, or balancing can be done by placing the blade on an inverted line punch or 5/8" bolt. Blade should not lean or tilt. Spin the blade slowly, blade should not wobble. If blade is out of balance, true it up before reinstalling.

22 601156_0308

Cap screw

FasTrak 36/42 shown

Cap screw

Seat

release

handle

FasTrak 36/42 shown

Figure 5-11

IMPORTANT: When mounting blades, rotate them after installation to

ensure blade tips do not touch each other or sides of the mower.

Upper

control

lever

Lower

control

lever

Figure 5-1

Figure 5-9

Figure 5-10

Lay the blade on a flat surface and check for distortion (Fig. 4-7 and 4-

8). Replace any distorted blade. Do not re-use spindle bolts which have stripped, worn or undercut

threads. Torque bolts on spindles to 118 foot-pounds (160.01nm) when reinstalling blades.

IMPORTANT: The blade sail (curved part) must be pointing upward

toward the inside of the deck to ensure proper cutting.

WARNING: Failure to correctly torque the bolt may result in the loss of the blade which can cause serious injury.

WARNING: Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves and use extra caution when servicing them.

Seat adjustment

FasTrak 36/42 (Mini FasTrak 36/42) - The seat can be adjusted for-

ward and rearward by removing the locknut that locks the seat platform in place and pivoting the seat platform up and forward. Then loosen the four cap screws on the underneath side of the operator’s platform. Position the seat where you have the best control of the machine and are the most comfortable and then tighten the cap screws. Fig. 4-9

FasTrak 48/5 4 - The seat can be adjusted forward and rearward by slid-

ing the seat release handle and moving the seat until a comfortable operating position is attained. Fig. 4-10

Steering control lever adjustment

The steering control levers can be adjusted for operator comfort. By loosening the cap screws that attaches the upper control lever to the lower lever (Fig. 4-11), the upper control lever can be pivoted to fit the operator’s personal preference.

The steering control levers can also be adjusted up and down. Remove the cap screws and slide the upper control lever up or down and align the holes in it with the holes in lower lever. Re-install the cap screws and tighten.

The steering control levers should be adjusted so that they align with each other when in the neutral position.

601156_0308 23

FasTrak 36/42

Mini FasTrak 36/42

Maintenance Schedule

Refer to Fig. 4-12

SERVICE AT

INTERVALS INDICATED

Verify safety start interlock system Prior to each use Visually inspect unit for loose

hardware and/or damaged parts Prior to each use Visually inspect tires Prior to each use Check oil level, engine (1) Prior to each use or every 4 hours Clean air intake screen (4) Prior to each use or every 4 hours Clean foam element (4) Prior to each use or every 4 hours Check fuel level Prior to each use Blades - sharpen & securely fastened Prior to each use Discharge chute - securely in place &

in lowest position Prior to each use Clean engine and transaxle

compartment Daily Grease deck height pivots X Grease gauge wheel bearings X Change engine oil and filter (1) (3) X Clean cylinder and head fins(a) X Check battery connections X Check tire pressure with a gauge X Clean engine exterior (a) X Replace air cleaner paper el ement (4 ) X Clean & regap spark plugs (a) X Check pump and deck belt tension

and condition (5) X Check fuel and hydraulic lines (6) X Check fuel valve and grommet (6) X Tighten lug nuts on wheels (2) X Change fuel filter X Replace spark plugs X

WEEKLY

OR 50

HOURS

ANNUALLY

OR 100 HOURS

FasTrak 48/54

Maintenance Schedule

Refer to Fig. 4-13

SERVICE AT

INTERVALS INDICATED

Verify safety start interlock system Prior to each use Visually inspect unit for loose

in lowest position Prior to each use Clean engine and transaxle

compartment Daily Change transaxle oil and filter (7) Every 200 hours or 2 years Grease deck height pivots X Grease gauge wheel bearings X Change engine oil and filter (1) (3) X Clean cylinder and head fins(a) X Check battery connectio ns X Check tire pressure with a gauge X Check hydraulic oil level X Clean engine exterior (a) X Clean & regap spark plugs (a) X Check pump and deck belt tension

and condition (5) X Check fuel and hydraulic lines (6) X Check fuel valve and grommet (6) X Tighten lug nuts on wheels (2) X Change fuel filter X Replace spark plugs X

WEEKLY

OR 50

HOURS

MONTHLY

OR 100 HOURS

ANNUALLY

OR 300 HOURS

NOTES:

1. Initial oil change is after 5 hours of operation. Thereafter, change oil after

every 40 hours operation. Change more often under dusty or dirty conditions and during hot weather periods.

2. Torque initially and after first 2 hours of oper ation.

3. Change engine oil filter per the engine manufacturer’s recommendations.

Refer to Engine Owner’s Manual for recommendations and other maintenance items.

4. Service more often under dusty or dirty conditions.

5. Pump drive belt only - Inspect every 6 months or 100 hours and replace if worn or cracking is noticed. Otherwise, replace every 200 hours or 2 years whichever comes first.

6. Check fuel line hoses, fuel valve and grommets for any cracks or leaks

REFERENCES:

a — Refer to Engine Owner’s Manual

NOTE: After completing maintenance cycle (100 hours), repeat cycle.

601156_0308 24

NOTES:

1. Initial oil change is after 5 hours of operation. Thereafter, change oil after

every 40 hours operation. Change more often under dusty or dirty conditions and during hot weather periods.

2. Torque initially and after first 2 hours of operation.

3. Change engine oil filter per the engine manufacturer’s recommendations.

Refer to Engine Owner’s Manual for recommendations and other maintenance items.

4. Service more often under dusty or dirty conditions.

5. Pump drive belt only - Inspect every 6 months or 100 hours and replace if worn or cracking is noticed. Otherwise, replace every 200 hours or 2 years whichever comes first.

6. Check fuel line hoses, fuel valve and grommets for any cracks or leaks

7. Initial system oil and filter change must be after the first 75 hours of use o r

1 year whichever comes first. Thereafter, replace filter and oil in each transaxle every 2 years or 200 hours, whichever comes first.

REFERENCES:

a — Refer to Engine Owner’s Manual

NOTE: After completing maintenance cycle (300 hours), repeat cycle.

FasTrak 36/42

Mini FasTrak 36/42

Maintenance Locator Chart

1. Engine Oil Fil & Dipstick

2. Fuel Filter 3a. Engine Air Cleaner (Honda) 3b. Engine Air Cleaner (Kohler)

4. Engine Oil Drain Plug

5. Battery

6. Fuel Tanks

7. Gauge Wheel Bearing Zerks (2)

8. Engine Oil Filter

9. Deck Lift Pivot Zerks (3)

10. Park Brake Switch (2)

11. Drive Tire

12. Deck Belt

13. Pump Belt

14. Blades

15. Engine Air Intake Screen

16. Front Gauge Wheel Tires

Viewed from top of unit

Figure 5-12

601156_0308 25

Viewed from top of unit

FasTrak 48/54 Maintenance

Locator Chart

Viewed from top of unit

1. Engine Oil Fil & Dipstick 2a. Fuel Filter (Honda) 2b. Fuel Filter (Kawasaki) 2c. Fuel Filter (Kohler) 3a. Engine Air Cleaner (Honda & Kawasaki) 3b. Engine Air Cleaner (Kohler)

4. Engine Oil Drain Plug

5. Battery

6. Fuel Tanks

7. Gauge Wheel Bearing Zerks (2)

8. Engine Oil Filter

9. Deck Lift Pivot Zerks (4)

10. Park Brake Switch (2)

11. Drive Tire

12. Deck Belt

13. Pump Belt

14. Blades

15. Engine Air Intake Screen

16. Front Gauge Wheel Tires

Viewed from bottom of unit

Figure 5-13

26 601156_0308

TROUBLESHOOTING

SYMPTOMS PROBABLE CAUSES

Starting motor does not crank

The engine will not start, starts hard or fails to keep running

Engine: Runs with continuous misfiring or engine runs unevenly or erratically

Loss of power or system will not operate in either direction

Overheating Air intake screen or clean-

Low engine oil pressure Low oil level Add oil

High oil consumption Numerou s See y ou r dea l er

Tractor jerky when starting or operates in one direction only

Steering control levers not in park brake position or switch not adjusted

Deck clutch switch engaged

Weak or dead battery Recharge or replace

Electrical connections are corroded or loose

20 amp fuse is blown Replace the 20 amp

For additional causes See engine manual

No fuel or line plugged Fill tank or replace line

Fuel valve is turned off Open the fuel valve

There is incorrect fuel in the fuel system

There is dirt in the fuel filter

Dirt, water or stale fuel in the fuel system

The choke is not on Move the choke lever to

Numerous See engine manual

Restrictions in air cleaner Service air cleaner

Poor compression See your dealer

Steering linkage needs adjustment

Tow valve open Close tow valve

The traction drive belt is worn, loose or broken

For additional causes See engine manual

ing fins clogged

For additional causes See engine manual

Oil diluted or too light Change oil and check for

Steering control linkage needs adjustment

Loose steering linkage Tighten linkage

Transaxle component faulty

SUGGESTED

REMEDIES

Place steering control levers in park brake position or re-adjust switch

Disengage clutch switch

Check the electrical connections

fuse

Drain the tank and replace the fuel with the proper type

Replace ther fuel filter

Contact your Hustler Dealer

Adjust linkage

Install a new traction driv e belt

Clean screen and fin

source of contamination

Adjust linkage

See your dealer

SYMPTOMS PROBABLE CAUSES

Tractor creeps when steering control levers are in neurtal

Tractor circles or veers in one direction

There is abnormal vibration

Uneven cutting height The blade(s) are not

Blades do not rotate The deck drive belt is

Steering linkage needs adjustment

Loose steering linkage Tighten linkage

Tires improperly inflated Adjust air pressure to 8 -

T ransxle component faulty See your dealer

The engine mounting bolts are loose

The engine pulley, idler pulley or blade pulley is loose

The engine is pulley is damaged

The cutting blade(s) is/are bent or unbalanced

A blade mounting bolt is loose

Spindle bearing is worn or loose

A blade spindle is bent Contact your Hustler

sharp

A cutting blade(s) is/are bent

The deck is not level Level the deck per the

An anti-scalp wheel is not set correctly

The underside of the deck is dirty

Tires improperly inflated Adjust air pressure to 8 -

A blade spindle is bent Contact your Hustler

worn, loose or broken

The deck drive belt is off the pulley

Electric clutch is not engaging

SUGGESTED

REMEDIES

Adjust linkage

10 psi

Tighten the engine mounting bolts

Tighten the appropriate pulley

Contact your Hustler Dealer

Install new cutting blade(s)

Tighten the blade mounting bolt

Replace or tighten spindle bearing

Dealer

Sharpen the blades

Install new cutting blade(s)

Deck leveling and height adjustment section of the parts manual

Adjust the height of the anti-scalp wheel

Clean the underside of the deck

10 psi

Dealer

Install a new deck drive belt

Install the deck drive belt and check for a reason

Check and/or replace 10 amp fuse. Contact your Hustler dealer

601156_0308 27

28 601156_0308

STORAGE

When storing the unit at the the end of the mowing season, the following

steps should be taken to ensure readiness for the next mowing season.

1. Remove all grass, dirt, and trash from tractor and mower. Clean tractor

and mower and touch up all scrapes with Hustler spray paint. IMPORTANT: Wash the machine with a mild detergent and water. Do not pressure wash the machine. Avoid excessive use of water, especially near the control panel, engine and the integrated pump/motor units.

2. Install new air filter per Engine Owner’s Manual.

3. Check thoroughly for any worn or damaged parts that need replacing

and order them from your dealer.

4. Thoroughly lubricate machine, according to lubrication instructions.

5. Block tractor up so weight is off tires.

NOTE: Do not deflate tires.

6. Remove the battery from machine A. Clean battery B. Check the electrolyte level C. Charge the battery, if necessary D. Store battery in a cool, dry place (do not expose to freezing temper-

atures)

E. Always keep the battery fully charged. (Especially important to

prevent battery damage when the temperature is below 32

F.)

6. Perform separate engine preparation as listed below.

7. Store tractor in a clean, dry place.

Preparation of engine for storage

When engine is to be unused for long periods, proceed as follows:

1. Run engine for a minimum of 15 minutes.

2. Drain oil from crankcase while engine is still warm.

3. Refill with fresh oil of proper viscosity.

4. Drain fuel tank and run the engine until it stops from lack of fuel. Gas-

oline evaporates if left in carburetor for long periods, forming gum and varnish deposits in carburetor. These deposits will cause engine flooding and loss of power.

5. Remove and replace fuel filter if not done in previous 100 hours.

6. Remove spark plugs and pour a tablespoon of engine oil into each spark

plug hole, Install plugs, but do not reconnect plug leads.

7. Crank engine with starter at least a dozen revolutions to distribute oil

over cylinder walls and valve mechanism.

8. Clean exterior surface of engine. Spread a light film of oil over any

exposed metal surfaces of engine that are subject to corrosion.

9. Clean dirt and chaff from cylinders and fins, blower housing and muf-

fler.

10. Check oil filler cap and fuel tank cap to make certain they are securely

in place.

11. Refer to engine manual for more information.

New season preparation

Before starting the tractor following post season storage, the following

servicing is required:

1. Clean tractor, removing trash and dirt accumulation.

2. Check engine oil level.

3. Fill fuel tank with fresh gasoline. Run machine at half speed for 5 min-

utes, checking operation of steering control lever. Stop engine and check for oil leaks, loose fittings and so forth.

4. Tighten any bolts that have loosened and make sure all hair pins, cotter

pins and clevis pins are in place.

5. Install all safety shields and review safety precautions listed in this

manual.

6. Check and inflate tires to 8-12 psi.

7. Refer to engine manual for more information.

PRODUCT LITERATURE

This section contains sources of additional literature concerning your tractor. Literature should be ordered from your Hustler dealer or direct fr om indicated source.

Parts Manuals

If you would like to order a Parts Manual for a particular tractor, the Hustler part number for that manual is listed in the following chart. Please contact your Hustler dealer to order the manual.

Model Model Number Parts Manual P/N List Price

FasTrak 36/42 Mini FasTrak 36/42

FasTrak 48/54 928275, 928291,

927343, 927350, 927368, 927376

928267, 928520, 928502

333559 $22.50

108277 $22.50

601156_0308 29

30 601156_0308

INDEX

PAGE PAGE

Anti-scalp wheels Belts

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Children Control Panel Controls Deck cutting height adjustment Driving the tractor Electrical system Engine air filter Engine oil and filter Engine starting FasTrak 48/54 Maintenance Locator Chart FasTrak 48/54 Maintenance Schedule Fuel system General engine maintenance Hydraulic system Lubrication Maintenance & Adjustments Introduction Mini FasTrak 36/42 Maintenance Locator Chart Mini FasTrak 36/42 Maintenance Schedule

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

. . . . . . . . . . . . . . . . . . . . . . . . . . . 17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

. . . . . . . . . . . . . . . . . . 27

. . . . . . . . . . . . . . . . . . . . . 25

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

. . . . . . . . . . . . . . . . . . . . 19

. . . . . . . . . . . . . . 26

. . . . . . . . . . . . . . . . . . 25

Mower blade removal Mower deck operation New season preparation Operating suggestions Operation Parts and service Parts Manuals Preparation of engine for storage Safe Operating Practices Safe Servicing Practices Safety and Instruction Decals Safety start interlock system Seat adjustment Slope Operation Steering control lever adjustment Stopping the engine Tires To the new owner Torque values Using a ramp

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

. . . . . . . . . . . . . . . . . . . . . . . . . .31

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

. . . . . . . . . . . . . . . . . . . . . . . . . .23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Model and serial number Moving tractor with stalled engine Mower blade maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

. . . . . . . . . . . . . . . . . . . . . . . . . 14

Using this manual Warranty registration

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

601156_0308 31

32 601156_0308

Hustler Turf Lawn Mower Accessory User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual