Husqvarna LZ5227TXPKOA, LZ6123LTKOA, LZ6127TKOA, LZ6130TXPKOA, LZ7230TXPKOA User Manual

Operator´s manual
LZ5227TXPKOA/968999309, LZ6123LTKOA/968999269,
LZ6127TKOA/968999271, LZ6130TXPKOA/968999311,
LZ7230TXPKOA/968999314
Please read the operator’s manual carefully and make sure
you understand the instructions before using the machine.
English
RIDER
LZ SERIES
Contents
Contents...................................................................1
Introduction .............................................................3
Congratulations....................................................3
General ................................................................3
Driving and Transport on Public Roads ...............3
Towing .................................................................3
Operating .............................................................3
Good Service .......................................................4
Manufacturing Number ........................................4
Symbols and Decals ...............................................5
Safety Instructions..................................................7
General Use.........................................................7
Driving on Slopes.................................................9
Children..............................................................10
Maintenance ......................................................11
Transport............................................................13
Roll over Protecion system ROPS .....................15
Customer responsibilities...................................15
Controls .................................................................16
Control Locations ...............................................16
1. Motion Control Levers....................................17
2. Hour Meter .....................................................18
3. Tracking knob ................................................18
4. Parking Brake ................................................18
5. Blade switch...................................................19
6. Ignition Switch................................................19
7. Fuses .............................................................19
8. Seat Locking Device ......................................20
9. Refueling........................................................20
10. Fuel Shut Off Valve......................................21
11. Seat Adjustment Lever.................................21
12. Choke Control ..............................................21
13. Throttle Control ............................................22
14. Lifting Lever for the Mower Deck .................22
Pump release valves..........................................23
Accessories........................................................23
Operation ...............................................................24
Training ..............................................................24
Roll bar and safety belt ......................................25
Before Starting ...................................................25
Starting the Engine ............................................25
To start an engine with a weak battery ..............29
Running..............................................................30
Operating on hills ...............................................31
Mowing Tips.......................................................32
Stopping the Engine...........................................33
Moving by Hand .................................................34
Maintenance ......................................................... 35
Maintenance Schedule...................................... 35
Battery............................................................... 37
Ignition System.................................................. 38
Checking the Safety System ............................. 39
Checking the Engine's Cooling Air Intake ......... 41
Checking and Adjusting the Throttle Cable....... 41
Checking and Adjusting the Choke Cable......... 41
Cyclon air filter maintenance............................. 42
Replacing the Fuel Filter ................................. 44
Checking the Fuel Pump’s Air Filter.................. 44
Checking Tire Pressures................................... 45
Checking the Parking Brake.............................. 45
Checking the V-belts ......................................... 45
Checking the Blades ......................................... 46
Adjusting the Mower Deck ................................ 48
Engine oil cooler................................................ 49
Cleaning and Washing ...................................... 50
Caster Wheels................................................... 50
Hardware........................................................... 50
Lubrication............................................................ 51
Lubrication Schedule......................................... 51
General ............................................................. 51
Lubricating the Cables ...................................... 52
Shaft Bushings and Linkage ............................. 52
Lubricating in Accordance with the Lubrication
Schedule ........................................................... 52
Trouble Shooting Guide ...................................... 62
Storage.................................................................. 65
Winter Storage .................................................. 65
Service .............................................................. 65
Wiring diagram .................................................. 66
Technical Data ..................................................... 67
Accessories .......................................................... 71
Torque Specifications........................................ 71
Conformity Certificates........................................ 72
USA requirements............................................. 72
Service Journal .................................................... 73
Delivery Service ................................................ 73
After the First 8 Hours ....................................... 74
25-Hour Service ................................................ 75
50-Hour Service ................................................ 76
100-Hour Service .............................................. 77
300-Hour Service .............................................. 78
At Least Once Each Year.................................. 79
English-1
WARNING!
Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower. Each person operating the mower must be of sound mind and body and must not be under the influence of any mind altering substance.
WARNING!
Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
WARNING!
Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
English-2

INTRODUCTION

Introduction
Congratulations
Thank you for purchasing a Husqvarna ride-on mower. This machine is built for the greatest efficiency and rapid mowing primarily of large areas. Controls in one place and a hydrostatic transmission regulated by steering controls also contribute to the machine’s performance.
This manual is a valuable document. Following the instructions (use, service, maintenance, etc.) by all who operate this machine can considerably increase the lifespan of your machine and even increase its resale value. It is also very important to follow the instructions for the safety of you and others.
If you sell your machine, be sure to give the operator’s manual to the new owner.
The final chapter of this operator’s manual comprises a Service Journal. Ensure that service and repair work is documented. A well kept service journal reduces service costs for the season-based maintenance and affects the machine’s resale value. Take the operator’s manual along when the machine is left at the workshop for service.
General
In this operator’s manual, left and right, backward and forward are used in relation to the machine’s normal driving direction.
Continuous dedication to improve our products require that specifications and design are subject to change without notice.
Driving and Transport on Public Roads
Check applicable road traffic regulations before driving or transporting on public roads. If the machine is transported, you must always use approved fastening equipment and ensure that the machine is well anchored. DO NOT operate this machine on public roadways.
Towin g
Do not tow this machine, it may cause damage to the drive system.
Do not tow any trailers, etc with this mower. They may jackknife or overturn causing damage to the mower and possibly serious injury to the operator.
Operating
This machine is constructed only for mowing grass on lawns and other free and even ground without obstacles such as stones, tree stubs, etc. The machine can also be used for other tasks when equipped with special accessories provided by the manufacturer, for which the operating instructions are provided in conjunction with delivery. All other types of use are incorrect. The manufacturer’s directions concerning operation, maintenance, and repairs must be carefully followed.
Lawnmowers and all power equipment, can be potentially dangerous if used improperly. Safety requires good judgement, careful use in accordance with these instructions and common sense.
The machine must only be operated, maintained, and repaired by persons that are familiar with the machine’s special characteristics and who are well versed in the safety instructions. Use only approved repair parts to maintain this machine.
Accident prevention regulations, other general safety regulations, occupational safety rules, and traffic regulations must be followed without fail.
Unauthorized modifications to the design of the machine may absolve the manufacturer from liability for any resulting personal injury or property damage.
English-3
INTRODUCTION
Good Service
Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer, see the certificate in the Service Journal in this operator’s manual.
When you need spare parts or support in service questions, warranty issues, etc., please consult the following professional:
This Operator’s Manual belongs to the machine with manufacturing number:
Engine Transmission
Manufacturing Number
The machine’s manufacturing number can be found on the printed plate affixed to the left in the engine compartment. Stated on the plate, from the top are:
The machine’s type designation (I.D.).
The manufacturer's type number (Model).
The machine’s serial number (Serial no.)
Please state the type designation and serial number when ordering spare parts.
The engine’s manufacturing number is stated on a barcode decal. This is placed on the left side of the crankcase, in front of the starter. The plate states:
The engine’s serial number (E/NO).
The engine’s type designation (Code).
Please state these when ordering spare parts.
The hydraulic pump’s manufacturing number is stated on a barcode decal affixed to the left side of the pump housing. The plate states:
The pump’s type designation.
The pump’s serial number.
The hydraulic motor’s manufacturing number is stated on a round metal plate. This is placed on the gable inside the motor. The plate states:
The hydraulic motor’s type designation and design version.
The hydraulic motor’s serial number.
English-4
SYMBOLS AND DECALS
Symbols and Decals
These symbols are found on the machine and in the operator’s manual. Study them carefully so that you know what they mean.
WARNING! Xxxxxxx xxxx xxxxxxxx xxx x
Xxxxx xxxxxx xx. xx xxxxxxxx xxxxx xxx xx.
Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should neglect to follow instructions given in the manual.
IMPORTANT INFORMATION Xxxxxxx xxxx xxxxxxxx xxx xxx
xxxx xxxxxx xx.
Used in this publication to notify the reader of a risk of material damage, particularly if the reader should neglect to follow instructions given in the manual. Used also when there is a potential for misuse or misassembly.
FuelChokeSlowFastNeutralReverse
Warning!
and flammable
Parking brake
CE conformity marking. Only for European market
Warning! Rotating blades, keep away from the discharge deck
Do not stand hereBattery acid is corrosive, explosive,
Noise emissions to the surroundings in accordance with the European Union’s directive. The machine’s emission is stated in the chapter
TECHNICAL DATA and on the decals.
Only machines for European market
Do not touch rotating parts
Use protective glasses
Use protective gloves
English-5
SYMBOLS AND DECALS
Read Operator´s Manual.
Whole body exposure to thrown objects.
Shut off engine & remove key before performing any maintenance or repair work.
Severing of fingers & toes.
Keep a safe distance from the machine.
Do not open or remove safety shields while engine is running.
Use on slopes no greater than 10°.
Careful backing up, watch for other people.
No passengers
Careful going forward, watch for other people.
Moving sharp blades under cover
English-6
ROPS warning decal

SAFETY INSTRUCTIONS

Safety Instructions
These instructions are for your safety. Read them carefully.
WARNING!
This symbol means that important safety instructions need to be emphasized. It concerns your safety.
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND
THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
General Operation
Read, understand, and follow all instructions on the machine and in the manual before starting.
Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.
Only allow responsible adults, who are familiar with the instructions, to operate the machine.
Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blades.
Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.
Never carry passengers. The machine is only intended for use by one person.
Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.
Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces.
Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working
Slow down before turning.
8011-512
Read the operator’s manual before starting the machine
8011-513
Clear the area of objects before mowing
Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting.
English-7
8011-520
Never take passengers
SAFETY INSTRUCTIONS
Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge guard.
Operate machine only in daylight or good artificial light.
Do not operate the machine while under the influence of alcohol or drugs.
Watch for traffic when operating near or crossing roadways.
Use extra care when loading or unloading the machine into a trailer or truck.
Always wear eye protection when operating machine.
Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.
Follow the manufacturer’s recommendation for wheel weights or counterweights.
Anyone who operates this machine must first read and understand this Operation Manual. Local laws may regulate the age of the user.
WARNING!
Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects, or other reproductive system damage. The engine exhaust contains carbon monoxide, which is a odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces.
Keep machine free of grass, leaves or other debris build-up which can touch hot exhaust / engine part and burn. Do not allow the mower deck to plow leaves or other debris which can cause build-up to occur. Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage.
English-8
SAFETY INSTRUCTIONS
Personal Safety Equipment
WARNING!
When using the machine, approved personal protective equipment (shown in illustrations) shall be used. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your retailer for help in choosing the right equipment.
Make sure that you have first aid equipment close at hand when using the machine.
Never use the machine when barefoot. Always wear protective shoes or boots, preferably with steel toecaps.
Always wear approved protective glasses or a full visor when assembling or driving.
Always wear gloves when handling the blades.
Never wear loose clothing that can get caught in moving parts.
Use ear protectors to avoid damage to hearing.
8011-670
Personal protective equipment
Slope Operation
Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
Mow up and down slopes (10 degrees maxium), not across.
Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles.
Choose a low ground speed so that you will not have to stop while on the slope.
Do not mow on wet grass. Tires may lose traction.
Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed slowly straight down the slope.
Mow up and down, not side-to-side
WARNING!
Do
not drive up or down hills with slopes greater than 10 degrees. And do not drive across any slopes.
6003-004
Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction, which could cause the machine to roll over.
English-9
SAFETY INSTRUCTIONS
Use extra care while operating machine with grass catchers or other attachments; they can affect the stability of the machine. Do not use on steep slopes.
Do not try to stabilize the machine by putting your foot on the ground.
Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel is over the edge or if the edge caves in.
Children
Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.
Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator.
Be alert and turn machine off if a child enters the area.
Before and while backing, look behind and down for small children.
Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine.
Never allow children to operate the machine.
Use extra care when approaching blind corners, shrubs, trees, or other objects that may block your view of a child.
8011-519
Be extra cautious when driving on slopes
8011-517
Never allow children to operate the machine
Keep children away from the work area
8011-518
English-10
SAFETY INSTRUCTIONS
Maintenance
WARNING!
The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed.
Safe Handling of Gasoline
To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.
Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
Use only approved gasoline container.
Never remove gas cap or add fuel with the engine running. Allow engine to cool at least two (2) minutes before refueling.
Never fuel the machine indoors.
Never store the machine or fuel container where there is an open flame, spark, or pilot light such as on a water heater or other appliances.
Before you begin refueling, minimize the risk of static electricity by touching a metal surface.
Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner. Always place containers on the ground away from your vehicle when filling.
Remove gas-powered equipment from the truck or tailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.
If fuel is spilled on clothing, change clothing immediately.
8011-516
Never fill the fuel tank indoors
WARNING!
The engine and the exhaust system, become very hot during operation. Risk for burns if touched.
Allow engine and exhaust system to cool at least two (2) minutes before refueling
Never overfill fuel tank. Replace gas cap and tighten securely.
Do not start the engine near spilled fuel.
Never use gasoline as a cleaning agent.
If leaks arise in the fuel system, the engine must not be started until the problem has been resolved.
English-11
SAFETY INSTRUCTIONS
Check the fuel level before each use and leave space for the fuel to expand, because the heat from the engine and the sun may otherwise cause the fuel to expand and overflow.
General Maintenance
Never operate machine in a closed area.
Keep all nuts and bolts tight to be sure the equipment is in safe working condition.
Never tamper with safety devices. Check their proper operation regularly.
Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage and remove any fuel-soaked debris. Allow machine to cool before storing.
If you strike a foreign object, stop and inspect the machine. Repair, if necessary, before restarting.
Never make any adjustments or repairs with the engine running.
8011-515
Never drive the machine in an enclosed space
Check grass catcher components and the discharge guard frequently and replace with manufacturer’s recommended parts, when necessary.
Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them.
Check brake operation frequently. Adjust and service as required.
Maintain or replace safety and instruction labels, as necessary.
Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven with defective or unmounted protective plates, protective cowlings, safety switches, or other protective devices.
Do not change the settings of governors and avoid running the engine with overly high engine speeds. If you run the engine too fast, you risk damaging the machine components.
Be very careful when handling battery acid. Acid on skin can cause serious corrosive burns. If you spill battery acid on your skin, rinse immediately with water.
Always use protective glasses when handling the battery.
WARNING!
The battery contains lead and lead compounds, chemicals that are considered to cause cancer, birth defects, and other reproductive system damage. Wash your hands after handling the battery.
English-12
SAFETY INSTRUCTIONS
Acid in the eyes can cause blindness, contact a doctor immediately.
Be careful when servicing the battery. Explosive gases form in the battery. Never perform maintenance on the battery when smoking or near open flames or sparks. The battery can explode and cause serious injury/damage.
Ensure that nuts and bolts, especially the fastening bolts for the blade attachments, are properly tightened, torqued and that the equipment is in good condition.
Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven with defective or unmounted protective plates, protective cowlings, safety switches, or other protective devices.
Do not change the settings of governors and avoid running the engine with overly high engine speeds. If you run the engine too fast, you risk damaging the machine components.
Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye injury. Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery.
WARNING!
Avoid electrical sparking and its consequences by the following routines:
6003-009
Do not smoke when performing maintenance on the battery. The battery can explode and cause serious injury/damage
8009-728
Risk of sparking
Use protective goggles.
Ensure that the fuel filler cap is mounted tightly and no flammable substances is stored in an open vessel.
Never work with the starter circuit if there is spilled fuel.
Disconnect the chassis cable from the battery first and reconnect it last.
Do not make a bridge short circuit across the starter relay to run the starter.
Never use the machine indoors or in spaces lacking proper ventilation. The exhaust fumes contain carbon monoxide, an odorless, poisonous, and lethal gas.
Stop and inspect the equipment if you
English-13
SAFETY INSTRUCTIONS
run over or into anything. If necessary, make repairs before starting.
Never make adjustments with the engine running.
The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. Only use approved repair parts for the machine.
The blades are sharp and can cause cuts and gashes. Wrap the blades or use protective gloves when handling them.
Check the parking brake’s functionality regularly. Adjust and service as necessary.
The mulch blades should only be used in familiar areas when higher quality mowing is desired.
Reduce the risk of fire by removing grass, leaves, and other debris that may have accumulated on the machine. Allow the machine to cool before putting it in storage.
8011-644
Clean the machine regularly
Regularly clean deck and underside of deck, avoid spraying engine and electrical components with water.
Transport
The machine is heavy and can cause serious crushing injuries. Be extra cautious when it is loaded on or unloaded from a vehicle or trailer.
Use an approved trailer to transport the machine. Activate the parking brake, turn off the fuel supply, and fasten the machine with approved fastening devices, such as bands, chains, or straps, when transporting.
Do not operate this machine on public roadways.
Check and abide by local traffic regulations before transporting the machine on any road.
Do not tow this machine, it may cause damage to the drive system.
WARNING!
Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin, causing serious injury. If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not administered immdediately.
IMPORTANT INFORMATION
The parking brake is not sufficient to lock the machine in place during transport. Ensure that the machine is well fastened to the transport vehicle. Always reverse the machine onto the transport vehicle to avoid tipping it over.
Do not tow any trailers, etc. with this mower. They may jackknife or overturn causing damage to the mower and possibly serious injury to the operator.
English-14
SAFETY INSTRUCTIONS
Roll over Protecion system ROPS
The ROPS increases the basic weight of the unit by 42 lbs/19 kg. The ROPS on the US units are standard, on the European units is the ROPS an accessory.
WARNING!
The structures capability may be imparired by structural damage if overturned, or alteration occurs. If any of these conditions take place, the total structure MUST be replaced.
Do not use ROPS as a lifting, attaching or anchoring point.
Do not use ROPS for wrecking or towing.
Do not exceed Max GVW: 2822 lbs/1283 kg.
Read machine operator´s manual before each use.
Securely fasten your seat belt if the unit has a ROPS.
Where possible, avoid operating the unit near ditches, embankments and holes.
Reduce speed when turning, crossing slopes and on rough, slick or muddy surfaces.
Stay off slopes too steep for safe operation.
Watch where you are going, especially at row ends, on roads and around trees.
Do not permit others to ride.
Operate the mower smoothly - no jerky turns, starts or stops.
When mower is stopped, set brakes securely and use park brake.
If any part of ROPS is damaged, the entire ROPS must be replaced.
Check all bolts including seat belt for correct torque before each use.
Check ROPS structure for damage before each use.
ROPS bar is NOT intended for use in sub zero temperatures.
Customer responsibilities
Read and observe the safety rules.
Follow a regular schedule in maintaining, caring for and using your mower.
Follow the instructions under "Maintenance” and "Storage” sections of this owner’s manual.
This machine has no brain. Use yours!
WARNING!
This mower is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, bush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
A spark arrester for the muffler is available through your authorized Husqvarna dealer.
English-15

CONTROLS

Controls
This operator’s manual describes the Husqvarna Zero Turn Rider. The rider is fitted with a Kawasaki or Kohler four-stroke V-Twin engine developing 25-30 horse power.
Transmission from the engine is made via two belt-driven hydraulic pumps, which in turn drive a hydraulic motor for each drive wheel. Using the left and right steering controls, the flow is regulated and thereby the direction and speed.
8011-464
Zero Turn Rider
Locations of the controls
Control Locations
Page Page
1. Motion control, levers 17 8. Seat locking device 20
2. Hour meter 18 9. Fuel tank cap 20
3. Tracking knob 18 10. Fuel shut off valve 21
4. Parking brake 18 11. Seat adjustment lever 21
5. Blade-switch 19 12. Choke control 21
6. Ignition switch 19 13. Throttle control 22
7. Fuses 19 14. Cutting height adjuster 22
English-16
8011-767
CONTROLS
1. Motion Control Levers
The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position. Furthermore, there is a neutral position, which is locked if the steering controls are moved outward.
When both controls are in the neutral position (N), the machine stands still.
By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively.
In order, for example, to turn right while moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right.
Zero turn can be achieved by moving one control backward (behind the neutral position) and carefully moving the other steering control forward from its neutral position. The rotation direction when zero turning is determined by which steering control is moved backward behind the neutral position. If the left steering control is pulled backward, the machine turns to the left. Use extra care when using this maneuver.
8011-788
Steering controls
WARNING!
The machine can turn very rapidly if one steering control is moved much further forward than the other.
If the steering controls are in uneven positions when standing still they can be adjusted using the adjustment screws on the steering lever, not the link system, for the controls.
1
2
4
1Forward 2 Neutral 3 Neutral slot, Neutral lock 4 Reverse
Motion control lever pattern (right side)
3
8011-791
English-17
CONTROLS
2. Hour Meter
The hour meter displays the total operating time.
It will flash CHG OIL (Change Oil) at 50 hour intervals. The flash duration is one hour before and one hour after the interval. The CHG OIL icon will come on and shut off automatically. The hour meter can not be manually reset.
3. Tracking knob
The tracking knob is located in front of the left control lever. Rotating this knob allows fine tuning adjustments so that the machine tracks straight with the drive levers in the full forward position.
hour meter
Hour meter
Rotate the knob clockwise (as viewed from the operating position) to increase the speed or counter clockwise to decrease the speed on the left control lever. Example: If control levers are full forward and the unit turns to the right, turn the tracking knob counter clockwise to decrease the speed on the left control lever.
4. Parking Brake
The parking brake is found on the left of the machine. Pull the lever backward to activate the brake and forward to release it.
8011-442
Tracking knob
English-18
8011-511-1
Parking brake not activated
CONTROLS
5. Blade switch
In order to engage the mower deck, pull the knob out; the mower blades are disengaged when the knob is depressed.
6. Ignition Switch
The ignition key is placed on the driver’s panel and is used to start and stop the engine.
8011-510
Blade Switch
IMPORTANT INFORMATION
Do not run the starter for more than five seconds each time. If the engine does not start, wait about 10 seconds before re­trying.
7. Fuses
The fuses are located in a holder to the left of the hydraulic tank. They are flat pin fuses of the same type used in automobiles.
There are three fuses, as well as socket for one spare fuse.
Fuse ratings and functions:
20 A, Primary fuse.
7.5 A, Mower deck coupling.
7.5 A, Accessory outlet
Socket for spare fuse.
8011-521
Ignition key and hour meter
8011-746
Fuses
English-19
CONTROLS
8. Seat Locking Device
Under the rear part of the seat is a locking device that locks the seat into its folded position. The seat has a linked fixture at the front edge and can be folded forward when the locking device is pushed.
9. Refueling
The machine has two fuel tanks, one on each side just behind the seat. The tanks take
5.7 gallons (22 liters) each.
8011-440
The seat’s locking device
The engine will run on a minimum of 87-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used beneficially. See also Technical Data concerning methanol and ethanol fuels.
WARNING!
Gasoline is highly flammable. Observe caution and fill the tank outdoors (see the safety rules).
WARNING!
Fill to bottom of filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.
When operating in temperatures below 32° F. (0° C.), use fresh, clean winter grade gasoline to help insure good cold weather starting.
8011-524
Fuel tanks
IMPORTANT INFORMATION
Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel the next season. See Storage Instructions for additional information. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur.
English-20
CONTROLS
10. Fuel Shut Off Valve
The fuel shut off valve is located at the right rear of the seat. The valve has three positions; right tank, left tank and center is the off position.
11. Seat Adjustment Lever
The seat can be adjusted lengthways. When making adjustments, the lever under the front edge of the seat is moved to the left (as seen by the driver in the seat), after which the seat can be moved backward or forward.
8011-506
Fuel shut off valve
12. Choke Control
The choke control is used for cold starts in order to provide the engine with a richer fuel mixture.
For cold starts the control should be pulled out.
8011-441
Lengthways adjustment
8011-508
Choke control
English-21
CONTROLS
13. Throttle Control
The throttle control regulates the engine speed and thereby the rate of rotation of the blades, assuming the blade switch is pulled out, see Engaging the Mower Deck.
In order to increase or decrease the engine speed, the control is moved downward or upward respectively.
Avoid idling the engine for long periods, as there is a risk of fouling the spark plugs.
USE FULL THROTTLE WHEN MOWING, for best mower performance and battery charging.
14. Lifting Lever for the Mower Deck
The lifting lever is used to place the mower deck in the transport position or one of the 17 different cutting height positions.
The cutting height is set by placing a peg in the hole for the desired cutting height and the peg is then locked on the inside (hidden in the illustration) with the supplied pin.
1. Pull the lever backward to the locked position to engage the transport position. The deck is then raised.
2. Depress the lock handle, counter hold, and move the lifting lever forward toward the peg to engage the set cutting height. The deck is then lowered.
3. The lifting lever can also be used to temporarily adjust the cutting height, such as when passing a minor bump in the lawn.
8011-509
Throttle control
8011-525-1
The mower deck’s lifting lever
IMPORTANT INFORMATION
In order to obtain an even cutting height it is important that the air pressure in all four tires is the same 15 psi (1 bar).
English-22
Cutting height pedal
On some models there is a deck assist lift pedal to aid in the lifting of the deck.
Pump release valves
IMPORTANT INFORMATION
Only rotate valve 1/4 - 1/2 turn to release system.
Tighten the valve moderately.
Do not overtighten the valve when closing. That can damage the valve seat.
CONTROLS
8011-465
Cutting height pedal
Pump release valves are located at the pumps. They are used to release the system so the machine may be moved by hand when not running. Tilt seat forward to gain access to the pumps. Use a 5/8” wrench to open valve.
Accessories
For mulching, there is a BioClip attachment available. This is mounted underneath the mower deck and consists of control plates and BioClip blades.
8011-507
Pump release valve
8011-566
BioClip attachment
English-23

OPERATION

Operation
Read "Safety Instructions" section and following pages, if you are unfamiliar with the machine.
Training
Zero turn mowers are far more manueverable than typical riding mowers due to their unique steering capabilities.
We recommend that this section be reviewed in its entirety prior to attempting to move the mower under its own power. Additionally, we suggest when first operating mower, use a reduced throttle speed and reduced ground speed by NOT moving control levers to the furthest forward or reverse positions during initial operation, or until operator becomes comfortable with controls. We also suggest first time users, or new users to ZeroTurn mowers to become familiar with the mowers movement on a hard surface, such as concrete or blacktop PRIOR to attempting to operate on turf. Until operator becomes comfortable with mower controls and zero turning capability, they may damage turf due to over aggressive maneuvers.
To move forward and backward
The direction and speed of the mowers movements is effected by the movement of the control lever(s) on each side of mower. The left control lever controls the left wheel motor. The right control lever controls the right wheel motor.
IMPORTANT INFORMATION
When control levers are in the reverse position they return to neutral when released. This may cause the mower to suddenly stop.
First time users should push mower (see "Moving by Hand" in the "Operation" section) to an open, flat area, without other people or vehicles/obstacles near by. In order to move unit under its own power, the operator must be in the seat, start engine (see "Before Starting" in the "Operation" section), adjust engine speed to idle, disengage park brake, do not engage blades at this time, rotate control levers inward. As long as the control levers have not been moved forward or backwards, mower will not move. Slowly move both control levers forward slightly, this will allow mower to start moving forward in a straight line. Pull back on control levers to the neutral position and mower should stop moving. Pull back slightly on control levers, this will allow mower to start moving backwards. Push forward on control levers to the neutral position and mower should stop moving.
To turn to the right
While moving in a forward direction, pull the right lever back towards the neutral position while maintaining the position of the left lever, this will slow the rotation of the right wheel and cause the machine to turn in that direction.
To turn to the left
While moving in a forward direction pull the left lever back towards the neutral position while maintaining the position of the right lever, this will slow the rotation of the left wheel and cause the machine to turn in that direction.
To zero turn
While moving in a forward direction, first pull both control levers back until the mower stops or slows dramatically. Then by alternating one lever slightly to the forward position and the other in the reverse position.
English-24
Loading...
+ 58 hidden pages