Husqvarna HUV4421G, HUV4421D, HUV4421GXP, HUV4421DXP User Manual

2007

Utility Vehicles

Gasoline and Diesel

Owner’s Manual

HUV 4421G

HUV 4421GXP

HUV 4421D

HUV 4421DXP

NOTICE

Warranty information appears on the last pages of this manual. No other warranties, express or implied, are contained herein. Your authorized representative checked the vehicle before it was delivered to you and will provide you a copy of the completed vehicle warranty registration form.

Husqvarna is not liable for errors in this manual or for incidental or consequential damages that result from the use of the material in this manual.

This manual contains proprietary information that is protected by copyright. All rights are reserved. No part of this manual may be photocopied, reproduced, or translated to another language without the written consent of Husqvarna, Inc.

The information contained in this document is subject to change without notice. Husqvarna reserves the right to make design changes to vehicles without obligation to make these changes

on units previously sold. These vehicles do not conform to Federal Motor Vehicle Safety Standards for automobiles or to FMVSS 500

for low-speed vehicles, and are not equipped for operation on public streets, roads, or highways.

Husqvarna Forest and Garden

7349 Statesville Rd. Charlotte, NC 28269

USA

www.usa.husqvarna.com/huv

2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual Page 1

FOREWORD

Thank you for choosing Husqvarna, a world leader in outdoor products. You have chosen the finest utility vehicle on the market. Please protect your investment and ensure that your Husqvarna vehicle provides years of reliable, superior performance by reading and following the maintenance instructions in this manual.

Your comfort and safety are important to us, so we urge you to read and follow the step-by-step operating instructions and safety procedures in this manual. These instructions must be followed in order to avoid the risk of severe personal injury. If you rent or loan your vehicle to others, we recommend that you ask them to read this manual before they operate the vehicle.

Husqvarna products are backed by a customer support system designed to offer you fast, courteous service. In the event that your Husqvarna vehicle needs repairs or service, we recommend that your local authorized Husqvarna representative perform them. For the name and address of the Husqvarna representative nearest you, logon to our web site at www.usa.husqvarna.com. If you would prefer to write to us, direct your letter to: Husqvarna, Attention: Marketing Services, 7349 Statesville Rd., Charlotte, NC 28269 USA. Your local authorized Husqvarna representative can also provide technical advice, parts, and service manuals.

We hope you will consider this owner’s manual a permanent part of your Husqvarna vehicle. If you sell the vehicle, please include the manual so that the next owner will have the important operating, safety, and maintenance information it contains. Translated owner’s manuals can be downloaded from the Husqvarna web site at www.usa.husqvarna.com/huv.

Page 2 2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual

TABLE OF CONTENTS

Safety Details ............................................................................................................................................ 7

General Warnings ...................................................................................................................................... 8

General Information ................................................................................................................................... 10

Model Identification .................................................................................................................................... 10

Controls and Indicators .............................................................................................................................. 10

Roll-Over Protective Structure and Safety Belts ........................................................................................ 15

Seat Latch and Adjustment ....................................................................................................................... 17

Pre-Operation and Daily Safety Checklist ................................................................................................. 17

Performance Inspection ............................................................................................................................. 18

Driving Instructions .................................................................................................................................... 19

Bed Latch and Prop Rod – HUV 4421G and HUV 4421D Only ................................................................ 22

Loading and Unloading Cargo ................................................................................................................... 23

Vehicle Load Capacities ............................................................................................................................ 23

Towing with the Vehicle ............................................................................................................................. 25

Transporting on a Trailer ........................................................................................................................... 25

Storage ...................................................................................................................................................... 26

Maintenance .............................................................................................................................................. 28

Periodic Service Schedule ......................................................................................................................... 29

Periodic Lubrication Schedule ................................................................................................................... 32

Brake Fluid Reservoir ................................................................................................................................ 33

Engine Oil .................................................................................................................................................. 34

Gearcase Lubrication ................................................................................................................................ 39

Engine Coolant – Diesel Vehicles ............................................................................................................. 41

Air Intake System ...................................................................................................................................... 41

Fueling Instructions ................................................................................................................................... 42

Battery ....................................................................................................................................................... 45

Using A Booster Battery (Jump Starting) ................................................................................................... 46

Cleaning the Vehicle .................................................................................................................................. 47

Accessories ............................................................................................................................................... 48

Subsequent Owner Registration ................................................................................................................ 49

Vehicle Specifications ................................................................................................................................ 50

2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual Page 3

ALL HUV 4421 MODELS

DIESEL WARNING DECAL

Vehicle Feature Identification

GASOLINE WARNING DECAL

(GASOLINE VEHICLES ONLY,

ON PASSENGER-SIDE SEAT SUPPORT)

HOT MANIFOLD

WARNING DECAL

(ON ENGINE

VALVE COVER)

(DIESEL VEHICLES ONLY,

ON PASSENGER-SIDE SEAT SUPPORT)

OPERATING

INSTRUCTIONS

(ON INSTRUMENT PANEL)

WINCH CABLE WARNING DECAL

(FOR VEHICLES WITH WINCH ACCESSORY)

(ON FRONT BODY)

HOT SURFACE WARNING DECAL

(ON COOLANT PIPES AND

UNDERSIDE OF BOTH SEATS)

FRAME GROUND WARNING DECAL

(ON VEHICLE FRAME NEAR BATTERY)

ROTATING PARTS AND HOT MANIFOLD DECAL

(ON DRIVER-SIDE VEHICLE FRAME)

Page 4 2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual

ALL HUV 4421 MODELS

UNDERAGE

WARNING DECAL

• Do not modify or remove Roll-over Protective Structure (ROPS).

• Replace ROPS if damaged. Do not attempt repair.

• Use seat belts during operation. Do not jump from vehicle.

• Keep away from drop-offs, steep slopes, and unstable surfaces.

NOTICE AND WARNING DECAL

Vehicle Feature Identification

WARNING

CCI 102961201

CERTIFICATION

DRIVER/PASSENGER WARNING

DECAL

ROTATING PARTS

DECAL - DIESEL

(UNDER SEAT ON

DRIVER-SIDE FRAME)

SERIAL NUMBER

DECAL

CRUSH AREA DECAL

AND PASSENGER SIDE)

VEHICLE LOADING DECAL

(ON DRIVER SIDE

(UNDER SEAT ON DRIVER-SIDE FRAME)

BED LATCH

WARNING DECAL

ROTATING PARTS DECAL - GAS

TRAILER HITCH

DECAL

(ON REAR RECEIVER HITCH)

(STANDARD VEHICLE)

(HIGH-CAPACITY OPTION)

2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual Page 5

Vehicle Feature Identification

Page 6 2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual

Safety Details

SAFETY DETAILS

ý WARNING

• This owner’s manual should be read completely before attempting to drive or service the vehicle. Failure to follow the instructions in this manual could result in property damage, severe personal injury, or death.

It is important to note that some vital statements throughout this manual and on the decals affixed to the vehicle are preceded by the words DANGER, WARNING, or CAUTION. For your protection, we recommend that you take special notice of these safety precautions. Safety precautions are essential and must be followed.

If any of the operation or warning decals on the vehicle become damaged, have been removed, or cannot be easily read, they should be replaced immediately to avoid possible property damage, personal injury, or death. Contact your Husqvarna dealer.

ý DANGER

• A DANGER indicates an immediate hazard that will result in severe personal injury or death.

ý WARNING

• A WARNING indicates an immediate hazard that could result in severe personal injury or death.

ý CAUTION

• A CAUTION with the safety alert symbol indicates a hazard or unsafe practice that could result in minor personal injury.

CAUTION

• A CAUTION without the safety alert symbol indicates a potentially hazardous situation that could result in property damage.

POS

TO FUSE BLOCK

NEG

TO GROUND

DIESEL VEHICLE SHOWN

Remove negative (–) cable first.

Figure 1 Battery Cable Removal

2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual Page 7

General Warnings

GENERAL WARNINGS

The following safety statements must be heeded whenever the vehicle is being operated, repaired, or serviced. Safety decal identification information is also included beginning on page 4. Other specific safety statements appear throughout this manual and on the vehicle.

DANGER

• Battery – Explosive gases! Do not smoke. Keep sparks and flames away from the vehicle and service area. Ventilate when charging or operating vehicle in an enclosed area. Wear a full face shield and rubber gloves when working on or near batteries.

• Gasoline/Diesel – Flammable! Explosive! Do not smoke. Keep sparks and flames away from the vehicle and service area. Service only in a well-ventilated area.

• Do not operate engine in an enclosed area without proper ventilation. The engine produces carbon monoxide, which is an odorless, deadly poison.

• A Husqvarna vehicle will not provide protection from lightning, flying objects, or other stormrelated hazards. If caught in a storm while driving a Husqvarna vehicle, exit the vehicle and seek shelter in accordance with applicable safety guidelines for your location.

ý WARNING

• Follow the procedures exactly as stated in this manual, and heed all DANGER, WARNING, and CAUTION statements in this manual as well as those on the vehicle.

• Do not leave children unattended on vehicle.

• Children requiring a child safety seat must not ride on the vehicle. Comply with state and local laws pertaining to child safety.

• The driver and passenger must be restrained at all times with the safety belts provided to help prevent injury in the event of sudden braking, collision, or roll-over.

• No more than one person per bucket seat at one time. No more than two persons per bench seat at one time. Do not allow people to ride in any part of the vehicle that is not equipped with a seat and a safety belt. Do not allow a passenger to hold a child in his or her lap while the vehicle is moving.

• Prior to leaving the vehicle unattended or servicing the vehicle, place attachment on the ground, set the park brake, place the Forward/Reverse handle in the NEUTRAL position, turn the key switch to the OFF position, and remove the key. Chock the wheels when servicing the vehicle.

• Improper use of the vehicle or failure to properly maintain it could result in decreased vehicle performance, severe personal injury, or death.

• Any modification or change to the vehicle that affects the stability or handling of the vehicle, or increases maximum vehicle speed beyond factory specifications, could result in severe personal injury or death.

• Check the vehicle for proper location of all vehicle safety and operation decals and make sure they are in place and are easy to read.

• For vehicles with cargo beds, remove all cargo before raising the bed or servicing the vehicle. If the vehicle is equipped with a prop rod, ensure that it is securely engaged while bed is raised. Do not close bed until all persons are clear of cargo bed area. Keep hands clear of all crush areas. Do not drop cargo bed; lower gently and keep entire body clear. Failure to heed this warning could result in severe personal injury or death.

WARNING CONTINUED ON NEXT PAGE...

Page 8 2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual

General Warnings

ý WARNING

• Only trained technicians should service or repair the vehicle. Anyone doing even simple repairs or service should have knowledge and experience in electrical and mechanical repair. The appropriate instructions must be used when performing maintenance, service, or accessory installation.

• To avoid unintentionally starting the vehicle:

- Disconnect battery cables, negative (–) cable first (Figure 1).

- Gasoline vehicles only: Disconnect the spark plug wires from the spark plugs.

• Frame ground – Do not allow tools or other metal objects to contact frame when disconnecting battery cables or other electrical wiring. Do not allow a positive wire to touch the vehicle frame, engine, or any other metal component.

• Wear safety glasses or approved eye protection when servicing the vehicle. Wear a full face shield and rubber gloves when working on or near batteries.

• Do not wear loose clothing or jewelry such as rings, watches, chains, etc., when servicing the vehicle.

• Use insulated tools when working near batteries or electrical connections. Use extreme caution to avoid shorting of components or wiring.

• When servicing the vehicle with part of the vehicle on jack stands, do not operate the engine with the Forward/Reverse handle in either the FORWARD or REVERSE position. The all-wheel

drive system will engage any wheel(s), front or rear, with traction.

Figure 2 All-wheel Drive Warning

2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual Page 9

General Information

SERIAL NUMBER

DH0601-123456

GENERAL INFORMATION

This manual includes operating procedures, maintenance, and regular servicing information for HUV 4421G, HUV 4421D, HUV 4421GXP, and HUV 4421DXP gasoline and diesel vehicles. All operating procedures, maintenance, and regular servicing are identical unless otherwise noted.

MODEL IDENTIFICATION

The serial number of each vehicle is printed on a bar code decal mounted on the frame above the brake pedal (Example: RC0601-123456) (Figure 3). There is also a second serial number decal mounted on the rear body frame behind the fuel tank. The fuel tank must be removed to view this decal. See following NOTE.

NOTE: Have the vehicle serial number available when ordering parts or making inquiries.

7349 STATESVILLE RD. CHARLOTTE, NC 28269

Figure 3 Serial Number

CONTROLS AND INDICATORS

See General Warnings on page 8.

ý WARNING

• Before allowing anyone to drive the vehicle, make sure the driver is familiar with all controls and operating procedures.

• Do not tamper with the high idle speed setting on the diesel vehicle. Doing so will void the warranty, as well as damage the engine and other components, and could result in property damage, personal injury, or death due to unsafe speeds.

• Do not shift the Forward/Reverse handle while the vehicle is in motion.

• Engine must be at idle before shifting the Forward/Reverse handle. Failure to do so may result in injury to inattentive passengers and (or) damage to the vehicle.

• To avoid unintentionally starting or rolling the vehicle, place attachment on the ground, set the park brake, place the Forward/Reverse handle in the NEUTRAL position, turn the key

switch to the OFF position, and remove the key when leaving the vehicle.

Page 10 2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual

Controls and Indicators

01/21

OPERATING INSTRUCTIONS

OFF

START

Figure 4 Instrument Panel – Gasoline Vehicles

01/21

OPERATING INSTRUCTIONS

OFF

PREHEAT

START

Figure 5 Instrument Panel – Diesel Vehicles

2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual Page 11

Controls and Indicators

KEY SWITCH – GASOLINE VEHICLES

The key switch (7) is mounted on the instrument panel to the right of the steering column (Figure 4, Page 11). It has three positions: OFF, ON, and START.

To start the vehicle, place the Forward/Reverse handle in the NEUTRAL position and turn the key to the START position, and hold it there until the engine starts. Activate the choke (14) as necessary. If the engine does not start after 10-15 seconds, release the key and repeat the procedure. Once the engine starts, release the key and it will return to the ON position. The engine will idle in neutral.The engine will continue to idle until the key is turned to the OFF position. See following WARNING, CAUTION, and NOTE.

ý WARNING

• Moving parts! Keep clear of the engine compartment while the engine is running.

CAUTION

• Do not shift the Forward/Reverse handle while the accelerator pedal is pressed. Shift the handle only when the vehicle is at a complete stop and the engine is at idle. Failure to heed this caution could result in damage to the transmission.

NOTE: The key can be removed only when the key switch is in the OFF position.

KEY SWITCH – DIESEL VEHICLES

The key switch (7) is mounted on the instrument panel to the right of the steering column (Figure 5, Page 11). It has four positions: PREHEAT, OFF, ON, and START.

Use the PREHEAT feature if the temperature falls below 23 °F (–5 °C). Do not hold the key in the PREHEAT position longer than 20 seconds. To preheat the glow plugs in cold weather, turn the key to the PREHEAT position, and hold it there for 10-15 seconds. Then turn the key to the START position, and hold it there until the engine starts. If the engine does not start after 10-15 seconds, turn the key to the OFF position and repeat the procedure. Once the engine starts, release the key and it will return to the ON position. The engine will idle in neutral. The engine will continue to idle until the key is turned to the OFF position. See previous WARN-

ING, CAUTION, and NOTE.

FORWARD/REVERSE CONTROL

The Forward/Reverse handle (6) is located on the right side of the instrument panel (Figure 4 and Figure 5, Page 11). The handle has three distinct positions: FORWARD (A), NEUTRAL (B), and REVERSE (C). Push

the handle up to operate the vehicle in the forward direction, or pull the handle down to operate the vehicle in reverse. The engine can be started only when the handle is in the NEUTRAL (middle) position. The engine must be at idle before shifting the Forward/Reverse handle. See WARNING and CAUTION on page 12.

Husqvarna vehicles operate at a reduced speed in reverse. The reverse buzzer will sound as a warning when the Forward/Reverse handle is in the REVERSE position.

ACCELERATOR PEDAL

The accelerator pedal (1) is the pedal farthest to the right (Figure 4 and Figure 5, Page 11).

With the engine running and the Forward/Reverse handle in the FORWARD or REVERSE position, vehicle speed will increase as the accelerator pedal is pressed. When the accelerator pedal is released, it will return to the original position and the engine will idle. See WARNING and CAUTION on page 12.

Page 12 2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual

Controls and Indicators

BRAKE PEDAL

The brake pedal (2) is located to the immediate left of the accelerator pedal (Figure 4 and Figure 5, Page

11). To slow or stop the vehicle, press the brake pedal.

PARK BRAKE

The park brake pedal (3) is located to the left of the brake pedal (Figure 4 and Figure 5, Page 11). To engage the park brake, first apply pressure to the brake pedal, then firmly press the park brake pedal until it latches into place. To disengage the park brake, pull the park brake release handle (4) (Figure 6). See following

WARNING.

ý WARNING

• The park brake has multiple locking positions and should be firmly locked to prevent the vehicle from rolling.

R E

U N L

R E S

TR0601-123456

Figure 6 Park Brake Release

STEERING ADJUSTMENT LOCK

The steering wheel position is adjustable. To adjust the steering wheel position, press down on the steering adjustment lock lever (5), then move the steering wheel to the desired position

(Figure 4 and Figure 5,

Page 11). While holding the steering wheel in the desired position, pull up on the steering adjustment lock lever to firmly lock the steering column in position. See following WARNING.

ý WARNING

• Ensure that the steering wheel lock is fully engaged before operating the vehicle.

12-VOLT ACCESSORY OUTLET

The 12-volt accessory outlet (11) is located to the right of the key switch (Figure 4 and Figure 5, Page 11). It provides a constant 12VDC with the key switch in the ON or OFF position. See following NOTE.

NOTE: Extended use of this accessory outlet can cause the battery to become heavily discharged.

2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual Page 13

Controls and Indicators

LOW OIL WARNING LAMP

The low oil warning lamp (9) is located on the instrument panel just to the left of the steering column (Figure 4 and Figure 5, Page 11). If the warning lamp lights up, oil should be checked and added to the engine as nec-

essary before vehicle use continues. The vehicle should never be driven when the low oil warning lamp remains lit. If the warning lamp alternately lights and darkens, the vehicle may be driven, but oil should be added at the first opportunity. If the oil level is correct and the warning lamp remains lit, have a trained technician check the vehicle. See following CAUTION.

CAUTION

• Failure to add oil immediately when the low oil warning lamp remains lit may result in permanent engine damage.

FUEL GAUGE/HOUR METER

The fuel gauge and hour meter (8) are housed together on the right side of the instrument panel (Figure 4 and Figure 5, Page 11). The fuel gauge operates when the key switch is in the ON position and allows the

operator to monitor the fuel level in the vehicle. The hour meter operates only when the engine is running, and should be used by the trained technician to track vehicle usage and determine when periodic service procedures are required. See Periodic Service Schedule on page 29.

HEADLAMP CONTROL

The headlamp control (12) is located on the left side of the instrument panel (Figure 4 and Figure 5, Page

11). Press the headlamp rocker switch to turn the headlamps on or off. See following NOTE.

NOTE: Using the headlamps for extended periods while the engine is either off or idling will discharge the

battery.

ELECTRIC BED LIFT – OPTIONAL ON SOME VEHICLES

The electric bed lift switch (13) is located on the instrument panel to the left of the key switch (Figure 4 and Figure 5, Page 11). See following NOTE.

NOTE: Remove cargo before raising the bed.

To lift the bed, push up and hold the rocker switch in the upper position. Release the switch to stop the lifting operation. To close the bed, press down and hold the switch in the lower position. The bed lift will make a loud clicking sound to signal that the bed is in the rest position.

HIGH-TEMPERATURE WARNING LAMP – DIESEL VEHICLES ONLY

The high-temperature warning lamp (10) is located on the instrument panel to the left of the steering column, next to the low oil warning lamp (9) (Figure 5, Page 11). The diesel engine is liquid-cooled; if the engine coolant has exceeded its normal safe operating temperature, the warning lamp will illuminate. If the warning lamp lights up, stop the vehicle and allow it to idle for approximately five minutes before stopping the engine. Contact a Husqvarna dealer/distributor or a trained technician. See following WARNING.

ý WARNING

• Allow the engine to cool before servicing the engine coolant system. Engine coolant can cause severe burns.

Page 14 2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual

Roll-Over Protective Structure and Safety Belts

ROLL-OVER PROTECTIVE STRUCTURE AND SAFETY BELTS

All HUV 4421 vehicles are equipped with a Roll-Over Protective Structure (ROPS) and safety belts for each occupant. See following WARNING.

ý WARNING

• The ROPS must be properly installed before operating the vehicle. Husqvarna strongly urges that the vehicle’s occupants be properly restrained at all times with the safety belts provided.

Pregnant woman: Consult your doctor for specific recommendations. The safety belt should be worn securely and as low as possible over the hips and not on the waist.

Injured person: Depending on the injury, first check with your doctor for specific recommendations. To secure the safety belt, sit up straight and well back in the seat. Pull the safety belt out of the retractor and

insert the tab into the buckle. A click will be heard when the tab locks into the buckle. Position the lap belt as low as possible on the hips – not on the waist.

The retractor will lock the belt during a sudden stop. It also may lock if the occupant leans forward too quickly. A slow, easy motion will allow the belt to extend, and the occupant can move freely. If the safety belt cannot be pulled out of the retractor, firmly pull the belt and release it. It should then pull smoothly out of the retractor.

To release the safety belt, press the buckle release button (1) and allow the belt to retract (Figure 7). If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains free of twists

as it retracts.

Figure 7 Release Safety Belt

ý WARNING

• Do not operate the vehicle with the ROPS removed. Doing so could result in property damage, personal injury, or death.

• Do not remove or modify any component of the ROPS structure. Doing so will result in voiding the ROPS certification and could weaken the ROPS, resulting in serious injury or death.

• Do not operate the vehicle if the ROPS is damaged. If the ROPS is damaged, replace the structure. Do not attempt repair.

• The driver and passenger must be restrained at all times with the safety belts provided to help prevent injury in the event of sudden braking, collision, or roll-over.

• In the event of a roll-over, do not attempt to jump or otherwise exit the vehicle. Remain seated with safety belt fastened and with arms and legs inside the vehicle.

WARNING CONTINUED ON NEXT PAGE...

2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual Page 15

Roll-Over Protective Structure and Safety Belts

ý WARNING

• After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.

• Loose fitting safety belts could increase the chance of injury due to sliding under the belt if sudden braking should occur. Keep the safety belt snug and positioned as low on the hip bone as possible.

• Use a single safety belt for one person at a time. Do not use a single safety belt for two or more people – this includes children.

• The Husqvarna vehicle is not designed to meet child seat compatibility requirements. Children requiring a child safety seat must not ride on the vehicle. Comply with state and local laws pertaining to child safety.

ý CAUTION

• Be careful not to damage the safety belt webbing or hardware.

• Inspect the safety belt system periodically. Check for cuts, fraying, and loose parts. Damaged parts should be replaced immediately. Do not disassemble or modify the system.

• Keep safety belts clean and dry. If cleaning is necessary, use a mild soap and lukewarm water solution. Do not use bleach, dye or abrasive cleaners as they may severely weaken the safety belts.

• Do not insert coins, clip, etc. in the buckle as this may prevent the tab from locking into the buckle properly.

• If the safety belt does not function normally, contact your Husqvarna dealer/distributor or trained technician immediately. Do not occupy the seat until the safety belt is repaired.

CARGO CAGE HEADRESTS

Vehicles Equipped with Cargo Cage Option

Some vehicles are equipped with a rear cargo cage. This cargo cage includes two adjustable headrests.

To adjust the headrests

1. Remove the headrest hardware (1) (Figure 8).

2. Raise or lower the headrest to the desired height.

3. Install the headrest hardware (1).

4. Hand-tighten the hardware until the headrest is securely attached to the cargo cage. See following

NOTE.

NOTE: Using tools to tighten the headrest hardware could result in overtightening. Overtightening the

headrest hardware could result in damage to the cargo cage structure and/or the hardware.

Page 16 2007 HUV 4421 Gasoline and Diesel Vehicle Owner’s Manual

+ 42 hidden pages