Page 1
1330SB-XLSb
Owner's Manual / 96193004100 / 2008-11
Page 2
IMPORTANT
Safe Operation Practices for Walk-Behind Snow Throwers
This snow thrower is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury.
Look for this symbol to point out im por tant safety precautions. It means
CAUTION!!! BE COME ALERT!!! YOUR
SAFE TY IS IN VOLVED.
WARNING: Always disconnect spark
plug wire and place it where it can not
con tact plug in order to pre vent ac ci den tal start ing when setting up, trans port ing, ad just ing or making re pairs.
WARNING: This snow thrower is for
use on sidewalks, driveways and other
ground level surfaces. Caution should
be exercised while using on sloping surfaces. Do not use snow thrower on
surfaces above ground level such as
roofs of residences, garages, porch es
or other such structures or buildings.
Training
1. Read, understand and follow all instructions on the
machine and in the manual(s) before operating this
unit. Be thoroughly familiar with the controls and the
proper use of the equipment. Know how to stop the
unit and disengage the controls quickly.
2. Never allow children to operate the equipment. Never
allow adults to operate the equipment without proper
instruction.
3. Keep the area of operation clear of all persons, particularly small children.
4. Exercise caution to avoid slipping or falling, especially
when operating the snow thrower in reverse.
Preparation
1. Thoroughly inspect the area where the equipment is
to be used and remove all doormats, sleds, boards,
wires, and other foreign objects.
2. Disengage all clutches and shift into neutral before
starting the engine (motor).
3. Do not operate the equipment without wearing adequate
winter garments. Avoid loose fitting clothing that can
get caught in moving parts. Wear footwear that will
improve footing on slippery surfaces.
4. Handle fuel with care; it is highly flammable
(a) Use an approved fuel container.
(b) Never add fuel to a running engine or hot en-
gine.
(c) Fill fuel tank outdoors with extreme care. Never fill
fuel tank indoors.
(d) Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place
containers on the ground, away from your vehicle,
before filling.
(e) When practical, remove gas-powered equipment
from the truck or trailer and refuel it on the ground.
If this is not possible, then refuel such equipment
on a trailer with a portable container, rather than
from a gasoline dispenser nozzle.
WARNING: Snow throwers have ex posed rotating parts, which can cause
severe injury from contact, or from material thrown from the discharge chute.
Keep the area of operation clear of all
persons, small children and pets at all
times including startup.
CAUTION: Muffler and other engine
parts become extremely hot during
operation and remain hot after engine
has stopped. To avoid severe burns on
contact, stay away from these areas.
WARNING: Engine exhaust, some of
its con stit u ents, and certain vehicle
com po nents contain or emit chem icals known to the State of Cal i for nia
to cause can cer and birth defects or
oth er re pro duc tive harm.
(f) Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times, until refueling is complete. Do not use a nozzle lock-open
device.
(g) Replace gasoline cap securely and wipe up spilled
fuel.
(h) If fuel is spilled on clothing, change clothing im-
mediately.
5. Use extension cords and receptacles as specified by
the manufacturer for all units with electric drive motors
or electric starting motors.
6. Adjust the collector housing height to clear gravel or
crushed rock surface.
7. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by manufacturer).
8. Always wear safety glasses or eye shields during operation or while performing an adjustment or repair to
protect eyes from foreign objects that may be thrown
from the machine.
Operation
1. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
2. Exercise extreme caution when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden
hazards or traffic.
3. After striking a foreign object, stop the engine (motor),
remove the wire from the spark plug, disconnect the
cord on electric motors, thoroughly inspect the snow
thrower for any damage, and repair the damage before
restarting and operating the snow thrower.
4. If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the cause.
Vibration is generally a warning of trouble.
5. Stop the engine (motor) whenever you leave the operating position, before unclogging the collector/impeller
housing or discharge chute, and when making any
2
repairs, adjustments or inspections.
Page 3
6. When cleaning, repairing or inspecting the snow thrower,
stop the engine and make certain the collector/impeller and all moving parts have stopped. Disconnect
the spark plug wire and keep the wire away from the
plug to prevent someone from accidentally starting the
engine.
7. Do not run the engine indoors, except when starting
the engine and for transporting the snow thrower in or
out of the building. Open the outside doors; exhaust
fumes are dangerous.
8. Exercise extreme caution when operating on slopes.
9. Never operate the snow thrower without proper guards,
and other safety protective devices in place and working.
10. Never direct the discharge toward people or areas
where property damage can occur. Keep children and
others away.
11. Do not overload the machine capacity by attempting
to clear snow at too fast a rate.
12. Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care when
operating in reverse.
13. Disengage power to the collector/impeller when snow
thrower is transported or not in use.
14. Use only attachments and accessories approved by
the manufacturer of the snow thrower (such as wheel
weights, counterweights, or cabs).
15. Never operate the snow thrower without good visibility
or light. Always be sure of your footing, and keep a firm
hold on the handles. Walk; never run.
16. Never touch a hot engine or muffler.
Clearing a Clogged Discharge Chute
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with
snow throwers. Never use your hand to clean out the discharge chute. To clear the chute:
1. SHUT THE ENGINE OFF!
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean-out tool, not your hands.
Maintenance and Storage
1. Check shear bolts and other bolts at frequent intervals
for proper tightness to be sure the equipment is in safe
working condition.
2. Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present
such as hot water heaters, space heaters, or clothes
dryers. Allow the engine to cool before storing in any
enclosure.
3. Always refer to operator’s manual for important details
if the snow thrower is to be stored for an extended
period.
4. Maintain or replace safety and instruction labels, as
necessary.
5. Run the machine a few minutes after throwing snow
to prevent freeze-up of the collector/impeller.
CONGRATULATIONS on your purchase of a new snow
thrower. It has been designed, engineered and man u fac tured to give best possible dependability and per for mance.
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center. We have competent, well-trained tech ni cians and
the proper tools to service or repair this unit.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your snow thrower
prop er ly. Always observe the “SAFETY RULES”.
SERIAL NUMBER: ___________________________
DATE OF PURCHASE: _______________________
THE MODEL AND SERIAL NUMBERS WILL BE FOUND
ON A DECAL ATTACHED TO THE REAR OF THE SNOW
THROWER HOUSING.
YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
TABLE OF CONTENTS
PRODUCT SPECIFICATIONS
Gasoline Capacity 4.0 Quarts
and Type: Unleaded Regular only
Oil Type SAE 30 (above 40°F)
(API SG–SL): SAE 5W-30 or 10W-30 (0° to +40°F)
SAE 0W-30 (below 0°F)
Oil Capacity: 28 Ounces
Spark Plug: Champion QC12YC (Gap: .030")
CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules.
• Follow a regular schedule in maintaining, caring for
and using your snow thrower.
• Follow the instructions under “Maintenance” and “Stor age” sec tions of this own er’s manual.
SAFETY RULES ........................................................ 2-3
PRODUCT SPECIFICATIONS ...................................... 3
CUSTOMER RESPONSIBILITIES ................................ 3
ASSEMBLY / PRE-OPERATION ............................... 5-7
OPERATION ............................................................ 8-13
MAINTENANCE SCHEDULE ..................................... 14
MAINTENANCE ..................................................... 14-15
SERVICE AND AD JUST MENTS ........................... 16-18
STORAGE ................................................................... 18
TROU BLE SHOOT ING ................................................ 19
REPAIR PARTS ..................................................... 20-39
WARRANTY ............................................ BACK COVER
3
Page 4
PARTS PACKED SEPARATELY IN CARTON
(1) POWER CORD
(198563)
(1) DISCHARGE CHUTE
EXTRA SHEAR BOLTS AND NUTS
(6) SHEAR BOLTS 1/4-20 x 1-3/4
(198636)
(1) FUEL STABILIZER PACKET
(1) AUGER CONTROL ROD
(1) TRACTION DRIVE CONTROL ROD
(6) SPACERS
(198638)
(6) LOCKNUTS
1/4-20
(73800400)
(1) MULTI-
WRENCH
(180684)
(1) SAFTEY IGNITION KEY
(193071)
(1) WASHER 3/8
(19131316)
(1) LOCKNUT
5/16-18
(751153)
ROTATOR HEAD MOUNTING
(1) LOCKNUT 3/8
(73800600)
CHUTE DEFLECTOR REMOTE CONTROL
(1) CARRIAGE BOLT
5/16-18 x 5/8
(72250505)
(1) LOCKNUT
1/4-20
(191730)
(1) NYLON
WASHER
(179246)
(3) RETAINER
SPRINGS
(169675)
(1) SHOULDER
BOLT 1/4-20
(179829)
(1) SPRING
(184505)
(2) FLAT WASHERS
(2) CARRIAGE BOLTS
3/8-16 x 2.25
4
(2) HANDLE KNOBS
Page 5
ASSEMBLY / PRE-OPERATION
Read these instructions and this manual in its entirety before you attempt to assemble or operate your new
snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly,
operation and maintenance of the product.
Your new snow thrower has been as sem bled at the factory with the ex cep tion of those parts left unassembled for shipping
purposes. All parts such as nuts, washers, bolts, etc., necessary to com plete the as sem bly have been placed in the parts
bag. To ensure safe and proper operation of your snow thrower, all parts and hard ware you assemble must be tightened
se cure ly. Use the correct tools as nec es sary to ensure proper tightness.
REMOVE SNOW THROWER FROM CAR TON
1. Remove all accessible loose parts and parts boxes
from carton.
2. Cut down all four corners of carton and lay panels flat.
3. Remove the two (2) screws securing the auger housing
to the pallet.
4. Remove all packing materials ex cept plastic tie holding
speed control rod to lower handle.
5. Remove the two (2) plastic ties securing the upper
handle to the pallet.
6. Remove snow thrower from carton and check carton
thor ough ly for ad di tion al loose parts.
HOW TO SET UP YOUR SNOW THROWER
TOOL BOX (See Fig. 10)
A toolbox is provided on your snow thrower. The toolbox is
located on top of the belt cover. Store the extra shear bolts,
nuts and multi-wrench provided in parts bag in the toolbox.
NOTE: The multi-wrench may be used for assembly of the
chute rotator head to snow thrower and making ad just ments
to the skid plates.
UPPER
HANDLE
HANDLE
KNOB
LOWER
HANDLE
SPEED
CONTROL
ROD
PLASTIC TIE
UNFOLD UPPER HANDLE
1. Raise upper handle to the operating position and
tight en handle knobs securely. Additional carriage
bolts, washers and handle knobs are in bag of parts.
Use to secure upper handle to lower handle. Install
in lower holes in handles.
INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)
1. Remove plastic tie securing rod to lower handle.
2. Insert rod into speed control bracket and secure with
retainer spring.
SPEED
CONTROL
BRACKET
FIG. 1
SPEED CON TROL ROD
RETAINER
SPRING
SPEED
CONTROL
LEVER
FIG. 2
5
Page 6
ASSEMBLY / PRE-OPERATION
INSTALL TRACTION DRIVE CONTROL ROD
(See Figs. 3 and 4)
The traction drive control rod has the long loop on the end
of the spring as shown.
1. Slide rubber sleeve up rod and hook end of spring into
eye of cable with loop opening down as shown.
2. With top end of rod positioned under left side of control
panel, push rod down and insert top end of rod into hole
in drive control bracket. Secure with retainer spring.
TRACTION DRIVE
CONTROL ROD
RUBBER
SLEEVE
LOOP
OPEN ING
DOWN
INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)
The auger control rod has the short loop on the end of the
spring as shown.
1. Slide rubber sleeve up rod and hook end of spring into
control arm with loop opening up as shown.
2. With top end of rod positioned under right side of
control panel, push down on rod and insert end of rod
into hole in auger control bracket. Secure with retainer
spring.
AUGER
CONTROL
ROD
RUBBER
SLEEVE
CONTROL
ARM
CABLE
TRACTION DRIVE
CON TROL LEVER
DRIVE
CONTROL
BRACKET
FIG. 3
FIG. 4
RETAINER
SPRING
TRACTION
DRIVE
CON TROL
ROD
LOOP
OPENING
FIG. 5
AUGER CONTROL ROD
RETAINER
SPRING
FIG. 6
UP
AUGER
CONTROL
LEVER
AUGER
CONTROL
BRACKET
6
Page 7
ASSEMBLY / PRE-OPERATION
INSTALL DISCHARGE CHUTE / CHUTE ROTATOR
HEAD (See Fig. 7)
NOTE: The multi-wrench provided in your parts bag may
be used to install the chute rotator head.
1. Place discharge chute assembly on top of chute base
with discharge opening toward front of snow thrower.
2. Position chute rotator head over chute bracket. If nec es sary, rotate chute assembly to align square and pin on un der side of chute rotator head with holes in chute brack et.
3. With chute rotator head and chute bracket aligned,
po si tion chute rotator head on pin and threaded stud
of mounting bracket.
4. Install 3/8 washer and locknut on threaded stud and
tighten securely.
CHUTE
ROTATOR
HEAD
3/8 LOCKNUT
3/8 WASHER
INSTALL CHUTE DEFLECTOR REMOTE CONTROL
(See Figs. 8 and 9)
1. Install remote cable bracket to discharge chute with
5/16-18 carriage bolt and 5/16-18 locknut as shown.
Tighten securely.
2. Install remote cable eyelet to chute deflector with
1/4-20 shoulder bolt, nylon friction washer and 1/4-20
locknut as shown. Tighten securely.
3. Install spring hooks between hex nuts on chute rotator
head and into hole in chute deflector as shown.
1/4-20
SHOULDER
BOLT
NYLON
WASHER
1/4-20
LOCK NUT
CABLE
EYELET
SPRING
CHUTE
DE FLEC TOR
HOOK
BE TWEEN HEX
NUTS
ON CHUTE
ROTATOR HEAD
5/16-18
CARRIAGE
BOLT
CHUTE
BRACKET
ALIGN BEFORE
TIGHTENING LOCKNUT
FIG. 7
PIN
THREADED
STUD
ROTATOR HEAD
MOUNT ING
BRACKET
REMOTE
CABLE
BRACKET
5/16-18
LOCKNUT
FIG. 8
CHUTE DEFLECTOR
CONTROL LEVER
FIG. 9
CHECK TIRE PRESSURE
The tires on your snow thrower were overinflated at the factory for shipping purposes. Correct and equal tire pres sure
is important for best snow throwing performance.
• Reduce tire pressure to 14-17 PSI (19-24.5 N-m).
7
Page 8
OPERATION
FORWARD
PRIMER
IGNITION KEY.
INSERT TO START
AND RUN,
PULL OUT TO STOP.
READ AND FOLLOW ALL SAFETY INFORMATION
AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
DANGER
OR WARNING
REVERSE
SNOW
DISCHARGE
TRACTION
DRIVE CONTROL
DISENGAGED
ENGAGED
KNOW YOUR SNOW THROWER
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare
the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save
this manual for future reference.
These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand
their meaning.
8
Page 9
OPERATION
GAS O LINE
FILLER CAP
MUF FLER
CHOKE
CON TROL
PRIM ER
SAFETY
IGNITION
KEY
NOTE: ITEMS ABOVE
ARE SHOWN IN
THEIR TYPICAL
LOCATION ON THE
ENGINE. ACTUAL
LOCATION MAY VARY
WITH THE ENGINE
ON YOUR UNIT.
FUEL
SHUT-OFF
VALVE
THROTTLE
/ ENGINE
CONTROL
ELECTRIC
START
BUTTON
DISCHARGE
CHUTE
CLEAN-OUT TOOL
AUGER
CONTROL
LEVER
RECOIL
(AUXILIARY)
STARTER
HANDLE
DE FLEC TOR
DRIVE SPEED
CON TROL LEVER
CHUTE
DISCHARGE CHUTE CONTROL LEVER
DEFLECTOR
REMOTE
CONTROL
LEVER
TRACTION
DRIVE
CONTROL
LEVER
LH TURN
TRIGGER
LIGHT
HANDLE
KNOB
MUF FLER
TOOLBOX
AU GERS
FIG. 10
MEETS A.N.S.I. SAFETY REQUIREMENTS
Our snow throwers conform to the standards of the American National Standards Institute.
Toolbox - used to store spare shear bolts, locknuts and
wrench.
Safety ignition key - must be inserted for the engine to
start and run. Remove when snow thrower is not in use.
Electric start button - used for starting the engine.
Recoil (auxiliary) starter handle - used for start ing en gine.
Primer - pumps additional fuel from the carburetor to the
cylinder for use when starting a cold engine.
Choke Control - used for starting a cold engine.
Throttle/engine control - used to se lect either FAST or
SLOW engine speed and to STOP the engine.
LH and RH turn triggers - used to steer the snow thrower.
Drive speed control lever - used to select forward or
reverse motion and speed of snow thrower.
Traction drive control lever - used to engage power-pro pelled for ward or reverse motion of snow thrower.
Auger control lever - used to engage auger motion (throw
snow).
Discharge chute control lever - used to change the di rec tion the snow is thrown.
Deflector remote control lever - used to change the
dis tance the snow is thrown.
Skid plate - used to adjust height of scraper bar from the
ground.
Drift cutter - used to cut through deep snowdrifts.
9
FREEWHEEL
CONTROL
DRIFT
CUTTER
SKID PLATE
Page 10
OPERATION
The operation of any snow thrower can result
in foreign objects thrown into the eyes, which
can result in severe eye damage. Always wear
safety glasses or eye shields while operating
your snow thrower or performing any ad just ments or repairs. We recommend standard safe ty glasses
or a wide vision safety mask worn over spectacles.
HOW TO USE YOUR SNOW THROWER
Know how to operate all controls before adding fuel or
attempting to start the engine.
STOPPING
TRACTION DRIVE
• Release traction drive control lever to stop the forward
or reverse movement of the snow thrower.
AUGER
• Release the auger control lever to stop throwing snow.
ENGINE
1. Move throttle control to “STOP” position.
2. Remove (do not turn) safety ignition key to prevent
unauthorized use.
NOTE: Never use choke to stop engine.
TO USE FUEL SHUT-OFF VALVE (See Fig. 11)
The fuel shut-off valve is located beneath the fuel tank on
the engine. Always op er ate the snow thrower with the fuel
shut-off valve in the OPEN position.
OPEN
OFF
FIG. 11
TO USE THROTTLE CONTROL (See Fig. 12)
The throttle control is located on the engine. Always op er ate
the snow thrower with the engine at full throttle. Full throttle
offers the best snow thrower performance.
FULLOFF
FIG. 13
TO CONTROL SNOW DISCHARGE (See Fig. 14)
WARNING: Snow throwers have ex posed rotating parts, which can cause
severe injury from contact, or from material thrown from the discharge chute.
Keep the area of operation clear of all
persons, small children and pets at all
times including startup.
WARNING: If the discharge chute or au ger become clogged, shut-off en gine
and wait for all moving parts to stop. Use
the clean-out tool, NOT YOUR HANDS,
to un clog the chute and/or auger.
The DIRECTION in which snow is to be thrown is controlled
by the discharge chute control lever.
• To change the discharge chute position, press down ward
on discharge chute control lever and move lever left
or right until chute is in desired position. Be sure lever
springs back and locks into desired position.
The DISTANCE that snow is thrown is controlled by the
position of the chute deflector. Set the deflector low to
throw snow a short distance; set the deflector higher to
throw snow farther.
• Press downward on chute deflector control lever and
move lever forward to lower the deflector and decrease
the distance. Move lever back to raise the deflector
and increase the distance. Be sure lever springs back
and locks into desired position.
DISCHARGE CHUTE
CONTROL LEVER
SLOW FAST
FIG. 12
TO USE CHOKE CON TROL (See Fig. 13)
The choke con trol is located on the en gine. Use the choke
control when ev er you are starting a cold en gine. Do not
use to start a warm en gine.
• To engage choke, turn knob counterclockwise. Slowly
turn knob clockwise to disengage.
CHUTE DEFLECTOR
REMOTE CONTROL LEVER
FIG. 14
TO THROW SNOW (See Fig. 15)
The auger rotation is controlled by the auger control lever
located on the right side handle.
• Squeeze auger control lever to handle to engage the
auger and throw snow.
10
• Release the auger control lever to stop throwing snow.
Page 11
AUGER
CONTROL
LEVER
OPERATION
SPEED and DIRECTION are controlled by the drive speed
control lever.
• Move speed control lever to de sired po si tion AFTER
engaging the trac tion drive control lever.
CAUTION: Do not move speed con trol le ver
unless engine is running. Damage to the snow
thrower can result.
FIG. 15
USING THE CLEAN-OUT TOOL (See Fig. 16)
In certain snow conditions, the discharge chute may become clogged with ice and snow. Use the clean-out tool
to dislodge this blockage.
When cleaning, repairing, or in spect ing, make
certain all controls are disengaged and the auger/impeller and all moving parts have stopped.
Disconnect the spark plug wire and keep the
wire away from the spark plug to prevent accidental starting.
• Release the auger control lever and shut off the engine.
• Remove the clean-out tool from it's mounting clip. Grasp
the tool firmly by the handle and push and twist the tool
into the discharge chute to dislodge the blockage.
After the packed snow has been dislodged, return the cleanout tool to it's mounting clip by pushing it into the clip.
• Make sure the discharge chute is pointed in a safe direction (no vehicles, buildings, people, or other objects are
in the direction of discharge) before restarting engine.
• Restart the engine, then squeeze the auger control
lever to the handle to clear snow from the auger housing and the discharge chute.
DISCHARGE CHUTE
• Slower speeds are for heavier snow and faster speeds
are for light snow and transporting the snow thrower. It
is recommended that you use a slower speed until you
are familiar with the operation of the snow thrower.
NOTE: When both traction drive and auger control levers
are engaged, the traction drive control lever will lock the
auger control lever in the engaged position. This will allow
you to release your right hand from the handle and adjust
the discharge chute direction without interrupting the snow
throwing process.
TRACTION DRIVE
CONTROL LEVER
FIG. 17
DRIVE
SPEED
CONTROL
LEVER
POWER STEERING OPERATION (See Fig. 18)
Steering triggers are used to assist in steering your snow
thrower. The triggers are located on the underside of each
handle. When a trigger is squeezed, it disengages the drive
wheel on that side of snow thrower and allows it to turn in
that direction.
• To turn left – squeeze left side trigger.
• To turn right – squeeze right side trigger.
CLEAN-OUT
TOOL
MOUNTING
CLIP
FIG. 16
TO MOVE FORWARD AND BACKWARD (See Fig. 17)
SELF-PROPELLING, forward and reverse movement of
the snow thrower, is controlled by the traction drive control
lever located on the left side handle.
• Squeeze traction drive control lever to handle to en gage
the drive system.
• Release traction drive control lever to stop the forward
or reverse movement of the snow thrower.
LH TURN
TRIGGER
RH TURN
TRIGGER
FIG. 18
TO ADJUST SKID PLATES (See Fig. 19)
NOTE: The wrench provided in your parts bag may be
used to adjust the skid plates.
Skid plates are located on each side of the auger housing
and adjust the clearance between the scraper bar and the
ground surface. Adjust skid plates evenly to proper height
for current surface conditions. For removal of snow in
normal con di tions, such as a paved driveway or side walk,
place skid plates in the highest position (lowest scraper
clear ance) to give a 1/8" clearance between the scraper
bar and the ground. Use a middle position if the surface
to be cleared is uneven.
11
Page 12
OPERATION
NOTE: It is not recommended to operate the snow thrower
over gravel or rocky surfaces. Objects such as gravel, rocks
or other debris, can easily be picked up and thrown by the
impeller, which can cause serious personal injury, property
dam age or damage to the snow thrower.
• If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clear ance) position.
1. Shut off engine and wait for all moving parts to stop.
2. Adjust skid plates by loosening the 1/2" hex nuts, then
moving skid plate to desired position. Be sure both
plates are adjusted evenly. Tighten securely.
SCRAPER BAR (See Fig. 19)
The scraper bar is not adjustable, but is reversible. After
con sid er able use it may become worn. When it has worn
almost to the edge of the housing, it can be reversed,
providing additional service before requiring replacement.
Replace a dam aged or worn scrap er bar.
HIGH POSITION
(LOW GROUND
CLEARANCE)
LOW POSITION
(HIGH GROUND
CLEAR ANCE)
HEX
NUTS
AUGER
HOUSING
SCRAPER
BAR
SKID PLATE
FREEWHEEL POSITION
TRANSMISSION ENGAGED
FIG. 21
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL (See Fig. 22)
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
1. Check engine oil with snow thrower on level ground.
2. Remove oil fill cap/dipstick and wipe clean, reinsert
the dipstick and screw tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
• To change engine oil, see “TO CHANGE ENGINE OIL”
in the Main te nance sec tion of this manual.
CHOKE
CONTROL
ENGINE OIL
FILL CAP / DIPSTICK
GAS O LINE
FILLER CAP
FUEL SHUT-
OFF VALVE
FIG. 19
TO USE DRIFT CUTTERS (See Fig. 20)
Use the drift cutters to cut through deep snowdrifts that are
higher than the front of the snow thrower.
• Loosen adjustment nuts enough to allow drift cutter to
be raised to highest position and tighten nuts securely.
Repeat for opposite side of snow thrower.
• When not using drift cutters, loosen adjustment nuts,
lower to storage position and tighten nuts securely.
AUGER
HOUSING
STORAGE
POSITION
FIG. 20
DRIFT
CUTTER
ADJUST-
MENT NUTS
TO TRANSPORT (See Fig. 21)
When pushing or towing your snowthrower, be sure to
disengage transmission by placing freewheel control into
FREE WHEEL po si tion. Freewheel control is located at the
rear of snowthrower.
• Pull freewheel control out to FREEWHEEL position.
• To reengage transmission, push control back in.
PRIM ER
SAFETY
IG NI TION
KEY
NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
FIG. 22
THROT TLE
ADD GASOLINE (See Fig. 22)
• Fill fuel tank to bottom of tank filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quan ti ties that can be used within 30
days to assure fuel freshness.
WARNING: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
12
STARTER
BUTTON
RECOIL
STARTER
HANDLE
Page 13
OPERATION
CAUTION: Alcohol blended fuels (called gas o hol or using ethanol or methanol) can attract
moisture which leads to separation and for ma tion of acids dur ing storage. Acidic gas can
damage the fuel system of an engine while in
storage. To avoid engine problems, the fuel
system should be emptied be fore stor age of
30 days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. See Storage In struc tions for ad di tion al
information. Never use engine or car bu re tor
cleaner products in the fuel tank or per ma nent
damage may occur.
TO START ENGINE
• Be sure fuel shut-off valve is in the “OPEN” position.
Your snow thrower engine is equipped with both a 120 Volt
A.C. electric starter and a recoil starter. The electric starter
is equipped with a three-wire power cord and plug and is
designed to operate on 120 Volt A.C. household current.
• Be sure your house is a 120 Volt A.C. three-wire
ground ed system. If you are uncertain, consult a
li censed electrician.
WARNING: Do not use the electric
start er if your house is not a 120 Volt
A.C. three-wire grounded system. Se ri ous per son al injury or damage to your
snow thrower could result.
COLD START - ELECTRIC STARTER
1. Insert safety ignition key (packed separately in parts
bag) into ignition slot until it clicks. DO NOT turn the key.
Keep the extra safety ignition key in a safe place.
2. Place throttle control in “FAST” position.
3. Rotate choke control to “FULL” position.
4. Connect the power cord to the engine.
5. Plug the other end of the power cord into a three-hole
grounded 120 Volt A.C. receptacle.
NOTE: Do not use primer when start ing en gine with the
electric starter.
6. Push starter button until engine starts.
IMPORTANT: Do not crank engine more than five con tin u ous seconds between each time you try to start. Wait 5 to
10 seconds between each attempt.
7. When the engine starts, release the starter button and
slowly move the choke control to the “OFF” position.
8. Disconnect the power cord from the receptacle first,
then from the engine.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operating temperature.
WARM START - ELECTRIC STARTER
Follow the steps above, keeping the choke control in the
“OFF” position.
COLD START - RECOIL STARTER
1. Insert safety ignition key (packed separately in parts
bag) into ignition slot until it clicks. DO NOT turn the key.
Keep the extra safety ignition key in a safe place.
2. Place throttle control in “FAST” position.
3. Rotate choke control to “FULL” position.
4. Push the primer four (4) times if the temperature is
below 15°F, or two (2) times if temperature is between
15° and 50°F. If temperature is above 50°F, priming is
not nec es sary.
NOTE: Over priming may cause flooding, preventing the
engine from starting. If you do flood the engine, wait a
few minutes be fore at tempt ing to start and DO NOT push
the primer.
5. Pull recoil starter handle quickly. Do not allow starter
rope to snap back.
6. When the engine starts, release the recoil starter han dle
and slowly move the choke control to the “OFF” position.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operating temperature.
WARM START - RECOIL STARTER
Follow the steps above, keeping the choke in the “OFF”
position. DO NOT push the primer.
BEFORE STOPPING
Run the engine for a few minutes to help dry off any moisture on the engine.
IF RECOIL STARTER HAS FROZEN
If the recoil starter has frozen and will not turn the engine,
proceed as follows:
1. Grasp the recoil starter handle and slowly pull as much
rope out of the starter as possible.
2. Release the recoil starter handle and let it snap back
against the starter.
If the engine still fails to start, repeat the above steps or
use the electric starter.
SNOW THROWING TIPS
• Always operate the snow thrower with the engine at
full throttle. Full throttle offers the best performance.
• Go slower in deep, freezing or heavy wet snow. Use the
drive speed control, NOT the throttle, to adjust speed.
• It is easier and more efficient to remove snow im me di ate ly after it falls.
• The best time to remove snow is the early morning. At
this time the snow is usually dry and has not been exposed to the direct sun and warming tem per a tures.
• Slightly overlap each successive path to ensure all
snow will be removed.
• Throw snow downwind whenever possible.
• Ad just the skid plates to proper height for current snow
con di tions. See “TO ADJUST SKID PLATES” in this
section of this manual.
• For extremely heavy snow, re duce the width of snow
removal by over lap ping previous path and moving
slowly.
• Keep engine clean and clear of snow during use. This
will help air flow and extend engine life.
• After snow-throwing is completed, allow engine to run for
a few minutes to melt snow and ice off the engine.
• Clean the entire snow thrower thoroughly after each
13
use and wipe dry so it is ready for next use.
Page 14
WARNING: Do not operate snow thrower if weather conditions im pair visibility. Throwing snow
dur ing a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the
snow thrower.
MAINTENANCE
GENERAL REC OM MEN DA TIONS
The warranty on this snow thrower does not cover items
that have been sub ject ed to operator abuse or negligence.
To receive full value from the warranty, operator must
maintain snow thrower as in struct ed in this manual. Some
ad just ments will need to be made periodically to properly
maintain your snow thrower.
All adjustments in the Service and Ad just ments section of
this manual should be checked at least once each season.
• Once a year, you should replace the spark plug and
check belts for wear. A new spark plug will help your
engine run better and last longer.
• Follow the maintenance schedule in this manual.
NOTE: Use only Original Equipment Manufacturer (OEM)
parts to service this unit. Failure to do so can cause the unit
to malfunction and pose a risk of injury to the operator.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
3. Check controls to be sure they are functioning properly.
LUBRICATION
Keep your snow thrower well lubricated
(See “LU BRI CA TION CHART”).
LUBRICATION CHART
➀ SAE 30 Motor Oil
See “ENGINE” in
➁
Maintenance section
General
➂
Purpose
Grease
➀ Pivot points
➂ Auger
grease fittings
➁
Engine
oil
14
Page 15
MAINTENANCE
SNOW THROWER
Always observe safety rules when performing main te nance.
TIRES
• Maintain proper air pressure in both tires (14–17 P.S.I.
/ 19-24.5 N-m).
• Keep tires free of gasoline / oil, which can harm rubber.
NOTE: To seal tire punctures and prevent flat tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and cor ro sion.
V-BELTS
Check V-belts for deterioration and wear after every 50
hours of operation and replace if necessary. The belts
are not ad just able. Replace belts if they begin to slip from
wear. (See “TO REMOVE BELT COVER” in the Service
and Adjustments section of this manual).
The V-belts on your snow thrower are of special con struc tion
and should be replaced by original equipment man u fac tur er
(OEM) belts avail able from your dealer. Using other than
OEM belts can cause personal injury / damage to the thrower.
AUGER GEAR CASE
• The gear case was filled with lubricant to the proper level
at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.
• If lubricant is required, use only Ronex ED #1 grease.
TRACTION DRIVE SYSTEM
DO NOT lubricate the drive components inside the snow
thrower. The sprockets, hex shafts, drive disc and friction
wheel require no lubrication. The bearings and bushings
are lifetime lubricated and require no maintenance.
CAUTION: Any lubricating of the above com po nents can cause contamination of the friction
wheel and damage to the drive system of your
snow thrower.
ENGINE
See engine manual.
LUBRICATION
Use only high quality detergent oil rated with API service
classification SG–SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.
Check the crankcase oil level before starting the engine and
after each five (5) hours of continuous use. Tighten oil fill
cap / dipstick securely each time you check the oil level.
TO CHANGE ENGINE OIL
Determine temperature range anticipated before next oil
change. All oil must meet API service classification SG–SL.
• Be sure snow thrower is on level surface.
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
NOTE: The left side wheel may be removed from snow
thrower for easier access to the oil drain plug and place ment of a suitable container. The unit tilted, resting on the
frame with the left wheel removed, will help drain any oil
trapped inside the engine. (See “TO REMOVE WHEELS”
in the Service and Adjustments section of this manual).
1. Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
2. Clean area around drain plug.
3. Remove drain plug and drain oil in a suitable container.
4. Install drain plug and tighten securely.
5. Wipe off any spilled oil from snow thrower and engine.
6. Install left wheel (if removed for draining oil). Be sure to
install klick pin into proper hole in wheel axle (See “TO
REMOVE WHEELS” in the Service and Adjustments
section of this manual).
7. Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine.
8. Refill engine with oil through oil dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCT SPECIFICATIONS” section of this man u al.
9. Use gauge on oil fill cap/dipstick for checking level.
Be sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick.
10. Wipe off any spilled oil.
MUFFLER
Inspect and replace corroded muffler as it could cre ate a
fire haz ard and/or dam age.
SPARK PLUG
Replace spark plug at the beginning of each season or after
every 100 hours of operation, whichever occurs first. Spark
plug type and gap setting are shown in the “PROD UCT
SPEC I FI CA TIONS” section of this manual.
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possible engine damage from running low on oil.
Change the oil after every 25 hours of operation or at least
once a year if thrower is not used for 25 hours in one year.
CLEANING
IMPORTANT: For best performance, keep snow thrower
housing free of any dirt or trash. Clean the outside of your
snow thrower after each use.
WARNING: Remove safety ignition key
and disconnect spark plug wire from
spark plug. Place wire where it can not
come in contact with spark plug.
• Keep finished surfaces/wheels free of gasoline, oil, etc.
• We do not recommend using a garden hose to clean
your snow thrower unless the electrical system, muffler
and carburetor are covered to keep water out. Water
15
in engine can result in shortened engine life.
Page 16
SERVICE AND ADJUSTMENTS
WARNING: To avoid serious injury, before performing any service or ad just ments:
1. Be sure throttle is in STOP position.
2. Remove safety ignition key.
3. Make sure the augers and all mov ing
parts have completely stopped.
4. Disconnect spark plug wire from
spark plug and place wire where it
can not come in contact with plug.
SNOW THROWER
TO ADJUST SNOW THROWER HEIGHT
See “TO ADJUST SKID PLATES” and “SCRAPER BAR”
in the Operation section of this manual.
CHUTE DEFLECTOR
The chute deflector, attached to the top of the discharge
chute, is provided to direct discharging snow away from
the operator. If the deflector becomes damaged, it should
be re placed.
WARNING: To avoid serious injury,
nev er operate your snow thrower with
the deflector removed or damaged.
• To change direction and/or distance snow is dis charged,
see “TO CONTROL SNOW DISCHARGE” in the Op er a tion section of this manual.
SHEAR BOLTS (See Fig. 23)
AUGER SHEAR BOLTS
Both right and left-hand augers are secured to the auger
shaft with a shoulder/shear bolt and hex nut. Should a foreign object or ice become lodged in the augers, the shear
bolts are designed to break, preventing damage to any
other com po nents. If one or both augers do not turn when
auger control lever is engaged, check to see if one or both
of the bolts have sheared. To replace the shear bolts:
1. Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
2. Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
3. Align hole in auger hub with hole in auger shaft and install
a new 1/4-20 x 2" shoulder/shear bolt and spacer. Install
1/4-20 lock nut and tighten securely.
To replace the capscrew/shear bolts:
1. Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
2. Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
3. Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 locknuts and tighten securely.
CAUTION: Do not substitute. Use only original
equip ment capscrew/shear bolts as sup plied
with your snow thrower.
4. Insert safety ignition key and reconnect spark plug wire
to spark plug.
1/4-20 x 1-5/8
CAPSCREW /
SHEAR BOLT
IMPELLER
HUB
1/4-20
LOCK NUT
1/4-20 x 2
SHOULDER /
SHEAR BOLT
SPACER
AUGER HUB
1/4-20 LOCKNUT
AUGER
SHAFT
IMPELLER
SHAFT
FIG. 23
TO REMOVE BELT COVER (See Fig. 24)
1. Remove two (2) screws securing belt cover to frame.
2. Remove belt cover.
• Replace belt cover by installing cover and screws and
tighten securely.
BELT
COVER
CAUTION: Do not sub sti tute. Use only original
equip ment shear bolts as sup plied with your
snow thrower.
4. Insert safety ignition key and reconnect spark plug wire
to spark plug.
IMPELLER SHEAR BOLTS
The impeller is secured to the impeller shaft with two (2)
capscrew/shear bolts and hex nuts. Should a foreign object
or ice become lodged in the impeller, the capscrews are
de signed to break, preventing damage to any other com po nents. If impeller does not turn when auger control lever
is engaged, check to see if the capscrews have sheared.
SCREWSFRAME
FIG. 24
16
Page 17
SERVICE AND ADJUSTMENTS
TO REPLACE BELTS (See Fig. 25)
The auger and traction drive belts are not adjustable. If the
belts are damaged or begin to slip from wear, they should
be replaced. It is recommended that the belt(s) be replaced
by a qualified service center.
NOTE: It is recommended that both the auger and traction
drive belt be replaced at the same time.
The V-belts on your snow thrower are of special con struc tion
and should be replaced by original equipment man u fac tur er
(OEM) belts avail able from your nearest dealer. Using other
than OEM belts can cause personal injury or damage to
the snow thrower.
WARNING: Belt replacement requires
separation of the snow thrower. While
separating the auger housing from the
frame assembly, it is important that
an assistant stand in the operating
po si tion and hold the snow thrower
han dles. Serious personal injury and/or
damage to the unit could occur if the
snow thrower should fall during the belt
chang ing process.
FRAME
ASSEMBLY
AUGER
HOUS ING
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into
the square hole in idler arm and rotate ratchet clockwise
to relieve tension.
8. With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
9. Place auger belt around and inside the groove of auger
pulley only.
10. While your assistant slowly raises handles to rejoin
the auger hous ing and frame assembly, pull up on the
auger belt and squeeze sides together above pulley
so belt is fully seated in groove of pulley.
11. Move idler arm so it does not hit impeller pulley as you
bring snow thrower completely together and check
carefully for proper routing of belts. If auger belt has
become dislodged from the pulley (by catching the idler
arm bracket while bringing snow thrower together),
separate the snow thrower and re peat step 12. Belt
must be fully seated in pulley groove when bring ing
the snow thrower together.
12. Install the two (2) hex bolts and tighten securely.
13. INSTALL ENGINE PULLEY - Place belt in pulley groove
and slide pulley on crankshaft. Install flat washer,
lockwasher and bolt and tighten securely (41-47 N-m
torque). Make sure belt is inside belt keeper.
14. INSTALL BELT COVER and two (2) screws. Tighten
securely.
15. INSTALL DISCHARGE CHUTE – See “INSTALL DIS CHARGE CHUTE / CHUTE ROTATER HEAD” in the
As sem bly / Pre-Operation section of this manual.
HANDLES
1. REMOVE GASOLINE FROM FUEL TANK - Drain
gasoline from fuel tank into a suitable container, out doors, away from fire or flame. Wipe up any spilled
gasoline.
2. REMOVE DISCHARGE CHUTE - Loosen locknut
se cur ing chute rotator head to mounting bracket only
enough to allow chute rotator head to be raised and
dis charge chute to be removed from snow thrower.
3. REMOVE BELT COVER - See “TO REMOVE BELT
COVER” in this section of this manual.
4. REMOVE ENGINE PULLEY - Remove bolt, lock wash er
and flat washer securing pulley to engine crankshaft.
Remove outside (auger) pulley only from crank shaft.
5. SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
re move the two (2) bolts holding auger housing and
frame together.
WARNING: As the last bolt is removed,
have your assistant carefully lower the
han dles down to the ground.
6. REMOVE AUGER BELT from around pulley.
7. RELIEVE TENSION ON TRACTION DRIVE BELT
IDLER and remove traction drive belt from around
pulleys.
17
IDLER ARM
SQUARE
HOLE
FRAME
TRACTION DRIVE BELT
CLUTCHING
IDLER ARM
BRACKET
AUGER PULLEY
BELT KEEPER
ENGINE
PULLEY
FIG. 25
FLAT WASHER
LOCKWASHER
BOLT
AUGER
BELT
AUGER
HOUSING
BOLTS
Page 18
TO REMOVE WHEELS (See Fig. 26)
• Remove the klik pin and remove wheel from axle.
IMPORTANT: When installing wheel, be sure to use the
axle hole closest to the end of the shaft – do not use the
hole in the wheel hub (if equipped). Inner hole in axle and
hole in wheel hub are not used for your model snow thrower.
KLIK PIN (INSTALL
IN OUTER HOLE
OF AXLE ONLY)
WHEEL
FIG. 26
OUTER HOLE
AXLE
WHEEL HUB
STORAGE
NOTE: To seal punctures or prevent flat tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and cor ro sion.
ENGINE
See engine manual.
CARBURETOR
Your carburetor is not adjustable. Engine performance
should not be affected at altitudes up to 7,000 feet (2,134
meters). If your engine does not operate properly due to
suspected carburetor problems, take your snow thrower
to a qualified service center.
ENGINE SPEED
Never tamper with the engine governor, which is factory set
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be dangerous and will
void the warranty. If you think the engine-governed high
speed needs adjusting, contact a qualified service center,
which has proper equipment and experience to make any
necessary ad just ments.
Immediately prepare your snow thrower for storage at
the end of the season or if the unit will not be used for 30
days or more.
WARNING: Never store the snow
thrower with gaso line in the tank in side
a build ing where fumes may reach an
open flame, spark or pilot light as on a
fur nace, water heater, clothes dryer or
gas ap pli ance. Allow the engine to cool
be fore storing in any enclosure.
SNOW THROWER
When snow thrower is to be stored for a period of time,
clean it thor oughly, re move all dirt, grease, leaves, etc.
Store in a clean, dry area.
1. Clean entire snow thrower (See “CLEANING” in the
Main te nance section of this manual).
2. Inspect and replace belts, if necessary (See “TO RE PLACE BELTS” in the Service and Adjustments sec tion
of this manual).
3. Lubricate as shown in the Main te nance sec tion of this
man u al.
4. Be sure that all nuts, bolts, screws, and pins are securely
fas tened. Inspect moving parts for damage, breakage
and wear. Replace if nec es sary.
5. Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
ENGINE
See engine manual.
FUEL SYS TEM
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
fuel hose, or tank during storage. Also, alcohol blended
fuels (called gasohol or using ethanol or methanol) can
attract moisture which leads to separation and formation
of acids during storage. Acidic gas can damage the fuel
system of an engine while in storage.
• Empty the fuel tank by starting the engine and letting
it run until the fuel lines and car bu re tor are empty.
• Never use engine or carburetor cleaner prod ucts in
the fuel tank or permanent damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in min i miz ing the formation of fuel gum deposits during stor age.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 min utes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not drain the
gas tank and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine
oil. (See “ENGINE” in the Maintenance section of this
man ual).
CYLINDER
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.
3. Pull recoil starter handle slowly a few times to dis trib ute
oil.
4. Replace with new spark plug.
OTHER
• Remove safety ignition key; store it in a safe place.
• Do not store gasoline from one season to another.
• Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
• If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.
• Cover your snow thrower with a suitable pro tec tive
cover that does not retain moisture. Do not use plastic.
Plastic cannot breathe, which allows con den sa tion to
form and will cause your snow thrower to rust.
IMPORTANT: Never cover snow thrower while engine/exhaust area is still warm.
18
Page 19
TROUBLESHOOTING
See appropriate section in manual unless directed to a qualified service center.
PROBLEM CAUSE CORRECTION
Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position.
equipped) in OFF position.
2. Safety ignition key 2. Insert safety ignition key.
is not inserted.
3. Out of fuel. 3. Fill fuel tank.
4. Throttle in STOP position. 4. Move throttle to FAST position.
5. Choke in OFF position. 5. Move to FULL position.
6. Primer not depressed. 6. Prime as instructed in the Operation section of this manual.
7. Engine is flooded. 7. Wait a few minutes before restarting, DO NOT prime.
8. Spark plug wire is 8. Connect wire to spark plug.
disconnected.
9. Bad spark plug. 9. Replace spark plug.
10. Stale fuel. 10. Drain fuel tank and carburetor, refill tank with fresh gasoline.
11. Water in fuel. 11. Drain fuel tank and carburetor, refill tank with fresh gas o line.
Loss of power 1. Spark plug wire loose. 1. Reconnect spark plug wire.
2. Throwing too much snow. 2. Reduce speed and width of swath.
3. Fuel tank cap is covered 3. Remove ice and snow on and around fuel tank cap.
with ice or snow.
4. Dirty or clogged muffler. 4. Clean or replace muffler.
Engine idles or 1. Choke is in FULL position. 1. Move choke to OFF position.
runs roughly 2. Blockage in fuel line. 2. Clean fuel line.
3. Stale fuel. 3. Drain tank and refill with fresh, clean fuel.
4. Water in fuel. 4. Drain fuel tank and carburetor, refill tank with fresh gasoline.
5. Carburetor is in need of 5. Contact a qualified service center.
adjustment or overhaul.
Excessive 1. Loose parts or damaged 1. Tighten all fasteners. Replace damaged parts.
vibration augers or impeller. If vibration remains, contact a qualified service center.
Recoil starter 1. Frozen recoil starter. 1. See “IF RECOIL STARTER HAS FROZEN”
is hard to pull in the Operation section of this manual.
Loss of traction 1. Drive belt is worn. 1. Check / replace drive belt.
drive / slowing 2. Drive belt is off of pulley. 2. Check / reinstall drive belt.
of drive speed 3. Friction drive wheel is worn. 3. Contact a qualified service center.
(if so equipped)
Loss of snow 1. Auger belt is off of pulley. 1. Check / reinstall auger belt.
discharge or 2. Auger belt is worn. 2. Check / replace auger belt.
slowing of 3. Clogged discharge chute. 3. Clean snow chute.
snow discharge 4. Augers / impeller jammed. 4. Remove debris or foreign object from augers / impeller.
19
Page 20
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
5
11
15
14
13
6
12
4
12
3
11
1
34
31
16
11
10
9
2
33
32
30
31
11
7
8
17
26
35
18
19
29
21
20
22
23
24
01.07.004-B
28
27
36
20
21
22
23
25
2 (EXPLODED)
Page 21
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
KEY PART
NO. NO. DESCRIPTION
1 532 18 41-05 IMPELLER
2 532 19 67-10 GEARBOX ASSEMBLY
3 532 18 89-09 BEARING
4 532 19 10-79 IMPELLER PULLEY
5 532 17 53-22 DISCHARGE BASE
6 532 18 40-95 CORNER BRACKET
7 532 19 21-99 CLEAN OUT TOOL
8 532 40 54-00 TOOL CLIP
9 873 80 04-00 NUT 1/4−20
10 874 78 04-26 SCREW 1/4−20 X .625
11 532 15 53-77 NUT 5/16−18
12 532 16 31-83 SCREW 5/16−18 X .625
13 819 11 15-07 WASHER
14 810 04 05-00 LOCKWASHER 5/16
15 874 94 05-16 SCREW 5/16−18 X 1.00
16 532 18 03-55 CARRIAGE BOLT
17 532 19 41-89 SCREW 13−16 X .625
18 532 40 77-60 PLUG
19 532 40 77-61 GEARBOX COVER RH
20 532 40 77-66 GASKET
21 532 40 77-70 SEAL
22 532 40 77-62 BEARING
23 532 17 46-97 THRUST WASHER 1.00
24 532 40 77-63 WORM GEAR
25 532 40 77-64 AUGER SHAFT
26 532 18 92-82 SQUARE KEY
27 532 40 77-58 BEARING
28 532 17 46-83 THRUST WASHER
29 532 40 77-57 IMPELLER SHAFT
30 532 18 42-05 ROLL PIN
31 532 17 46-81 THRUST WASHER
32 532 17 46-84 THRUST BEARING
33 532 40 77-69 BEARING
34 532 40 77-68 O−RING
35 532 40 77-67 SCREW 5/16−18 X .750
36 532 40 77-65 GEARBOX COVER LH
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
21
Page 22
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
1
KEY PART
NO. NO. DESCRIPTION
1 532 42 17-13 AUGER HOUSING
2 532 40 76-45 SCRAPPER BAR
3 (5x)
4 (5x)
2
3 872 27 05-05 CARRIAGE BOLT 5/16−18 X .625
4 532 15 53-77 NUT 5/16−18
01.07.023-B
2
1
KEY PART
NO. NO. DESCRIPTION
1 532 42 17-26 AUGER ASSEMBLY 30 LH
2 532 42 17-27 AUGER ASSEMBLY 30 RH
01.07.016-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
22
Page 23
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
2
1
1
2
3
KEY PART
NO. NO. DESCRIPTION
1 532 18 81-70 PLASTIC RETAINER
2 532 41 18-33 AUGER BALL BEARING
3 532 17 95-82 SCREW 5/16−18 X 1.00
3
01.07.007-A
2
3
1
3
KEY PART
NO. NO. DESCRIPTION
1 532 40 78-34 SKID PLATE
2 872 27 05-06 CARRIAGE BOLT 5/16−18 X .750
2
1
01.11.002-A
3 532 75 11-53 NUT 5/16−18
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
23
Page 24
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
1
KEY PART
3
4
5
1
2
4
3
3
5
4
3
4
2
NO. NO. DESCRIPTION
1 532 18 47-47 DRIFT CUTTER BAR
2 872 27 05-06 CARRIAGE BOLT 5/16−18 X .750
3 532 17 92-46 PLASTIC WASHER
4 810 04 05-00 LOCKWASHER 5/16
5 532 12 86-38 NUT 5/16−18
01.16.001-A
2
4
2
KEY PART
NO. NO. DESCRIPTION
1
4
1 532 18 25-16 WEIGHT BAR
2 872 11 05-10 CARRIAGE BOLT 5/16−18 X 1.25
3 532 75 11-53 NUT 5/16−18
4 819 11 22-06 WASHER
3
01.17.003-B
3
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
24
Page 25
REPAIR PARTS CONTROL PANEL / DISCHARGE CHUTE
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
5
7
16
17
3
6
KEY PART
NO. NO. DESCRIPTION
1 532 42 17-14 CHUTE WELDMENT
2 532 18 41-13 DEFLECTOR WELDMENT
3 532 42 11-63 DEFLECTOR CONTROL ASSEMBLY
4 532 42 03-25 DEFLECTOR SEAL
5 532 41 42-80 KNOB BLACK
6 532 12 84-15 POP RIVET
7 817 50 10-10 SCREW 10−24 X .625
8 532 41 98-21 CHUTE SNOW SHIELD
9 532 42 17-28 SHIELD RETAINER STRAP
*10 532 17 98-29 SHOULDER BOLT 1/4−20 X .375
*11 532 17 92-46 PLASTIC WASHER
*12 532 19 17-30 NUT 1/4−20
*13 872 25 05-05 CARRIAGE BOLT 3/8−16 X .625
6
*14 532 75 11-53 NUT 5/16−18
*15 532 18 45-05 DEFLECTOR SPRING
16 532 42 06-79 (SERVICE PART) DEFLECTOR CONTROL
17 532 42 11-64 (SERVICE PART) DEFLECTOR CABLE GRAY
18 532 42 11-38 DEFLECTOR SHIELD
19 532 42 32-47 DEFLECTOR SHIELD STRAP
19
1
*15
2
4
6
9
18
19
6
*12
*11
*10
6
*14
*13
01.09.006-C
8
NOTES:
1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
25
Page 26
REPAIR PARTS CONTROL PANEL / DISCHARGE CHUTE
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
2
2
1
*3
*6
KEY PART
NO. NO. DESCRIPTION
*4
*6
01.09.008-B
1 532 42 11-60 LEVER/CABLE ROTATOR ASSEMBLY GRAY
2 817 50 10-10 SCREW 10−24 X .625
*3 532 42 06-78 ROTATOR HEAD
*4 532 42 11-61 ROTATOR PIVOT BRACKET
*5 532 42 06-75 PULLEY PIVOT
*6 532 42 11-62 CABLE ASSEMBLY GRAY
NOTES:
1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.
*5
KEY PART
NO. NO. DESCRIPTION
1 532 42 12-31 STEER CABLE
2 874 04 10-24 SCREW 10−24 X 1.50
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
2
01.15.008-A
1
26
Page 27
REPAIR PARTS HANDLES
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
10
2
11
7
4
8
13
9
1
13
12
14
14
12
01.08.012-A
9
5
7
6
3
8
KEY PART
NO. NO. DESCRIPTION
1 532 41 55-39 CONTROL PANEL
2 532 42 17-06 CONTROL LEVER LH
3 532 42 17-07 CONTROL LEVER RH
4 532 41 55-46 TRACTION ROD ARM
5 532 42 14-92 IMPELLER ROD ARM
6 532 41 26-77 INTERLOCK ROD
7 532 41 26-80 SPACER
8 532 16 96-75 RETAINER
9 817 06 04-08 SCREW 1/4−20 X .50
10 532 41 42-80 KNOB BLACK
11 532 41 42-81 KNOB RED
12 532 17 88-99 HANDLE KNOB
13 819 13 13-16 WASHER 3/8
14 872 12 06-18 CARRIAGE BOLT 3/8−16 X 2.25
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
27
Page 28
REPAIR PARTS HANDLES
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
10
1
5
10
8
2
5
8
6
8
9
4
6
KEY PART
NO. NO. DESCRIPTION
7
1 532 42 17-08 PLOW HANDLE LH
2 532 42 17-09 PLOW HANDLE RH
9
3
3 532 19 69-44 PANEL BRACKET LH
4 532 19 69-43 PANEL BRACKET RH
7
5 532 41 45-15 HEATED HANDLE GRIP
6 874 78 05-12 SCREW 5/16−18 X .750
7 874 78 05-24 SCREW 5/16−18 X 1.50
8 532 75 11-53 NUT 5/16−18
9 532 15 54-15 WASHER
10 532 17 87-75 POP RIVET 1/8
01.08.011-A
1
KEY PART
NO. NO. DESCRIPTION
1 532 42 17-05 LOWER TUBE GRAY
2 532 40 76-43 PIVOT SUPPORT
3 532 15 00-78 BOLT 5/16−18 X .750
2
4 817 00 06-16 SCREW 3/8−16 X 1.00
4
3
4
4
3
4
01.05.006-B
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
28
Page 29
REPAIR PARTS HANDLES
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
11
1
3
2
KEY PART
NO. NO. DESCRIPTION
1 532 42 17-63 IMPELLER ROD ASSEMBLY
2 532 18 04-85 TRACTION ROD ASSEMBLY
3 532 18 77-82 SHIFTER ROD TOP
4 532 18 77-84 SHIFTER ROD BOTTOM
5 532 18 04-47 SPRING SLEEVE
9
6 532 19 20-91 SPRING SLEEVE
7 532 17 86-69 IMPELLER SPRING
8 532 18 09-26 TRACTION SPRING
10
9 872 27 05-06 CARRIAGE BOLT 5/16−18 X .750
10 532 15 53-77 NUT 5/16−18
11 532 16 96-75 RETAINER
6
11
5
01.12.002-C
7
8
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
29
Page 30
REPAIR PARTS HANDLES
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
4
KEY PART
NO. NO. DESCRIPTION
1 532 41 62-88 INTERLOCK SPRING
3
2 532 41 45-72 INTERLOCK CAM
5
2
1
3 532 17 88-31 TORSION SPRING
4 532 16 96-75 RETAINER
5 817 06 04-10 SCREW 1/4−20 X .625
6 532 42 18-14 INTERLOCK STOP
6
3
8
2
01.08.007-B
1
6
4
KEY PART
5
NO. NO. DESCRIPTION
1 532 42 13-51 CONSOLE PANEL GRAY
2 532 42 14-48 HEADLIGHT BEZEL GRAY
3 532 17 86-66 HALOGEN HEADLIGHT
4
4 532 18 44-71 SHOULDER SCREW 10−24 X .625
5 532 17 52-62 SCREW 10−24 X 1.25
7
5
6 532 41 77-60 GRIP SWITCH
7 532 40 56-99 WIRE HARNESS
8 532 40 16-20 BULB
01.10.010-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
30
Page 31
REPAIR PARTS DRIVE
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
6
7
4
8
2
3
7
1
9
2
5
3
4
6
01.03.003-A
KEY PART
NO. NO. DESCRIPTION
1 532 40 43-08 AXLE SHAFT
2 532 18 77-94 SPACER
3 532 17 46-97 THRUST WASHER
4 532 17 98-30 BEARING
5 532 14 63-15 SCREW 5/16−18 X .625
6 817 49 05-08 BOLT 5/16−18 X .500
7 532 15 54-43 CLIK PIN
8 874 78 06-32 SCREW 3/8−16 X 2.00
9 873 80 06-00 NUT 3/8−16
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
31
Page 32
REPAIR PARTS DRIVE
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
2
1
10
22
27
29
28
24
30
49
25
39
38
48
26
27
47
20
48
20
47
28
29
31
32
33
34
46
8
7
6
2
4
1
3
13
12
11
20
4
5
14
17
16
51
19
15
23
35
26
37
20
36
18
9
21
27
50
32
01.02.002-F
40
20
41
42
43
45
44
Page 33
REPAIR PARTS DRIVE
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
KEY PART
NO. NO. DESCRIPTION
1 532 19 20-02 SHIFT BRACKET
2 817 50 10-10 SCREW 10−24 X .625
3 874 76 05-52 SCREW 5/16−18 X 3.25
4 532 17 92-46 PLASTIC WASHER
5 532 19 20-01 SHIFT ASSEMBLY
6 532 15 54-15 WASHER
7 532 19 21-95 FRICTION SPRING
8 873 80 05-00 NUT 5/16−18
9 817 49 05-08 BOLT 5/16−18 X .500
10 532 40 54-84 CONTROL ARM
11 532 40 61-09 CONTROL SHAFT
12 532 05 70-79 WASHER
13 532 19 85-80 CLEVIS PIN
14 532 19 21-15 REAR PLATE
15 532 18 77-76 TRANSMISSION
16 532 19 32-56 ROD
17 532 19 20-00 REAR CABLE BRACKET
18 532 18 77-87 CONTROL ARM
19 532 19 19-93 FRONT CABLE BRACKET
20 532 15 00-78 SCREW 5/16−18 X .750
21 532 08 79-30 CLIP
22 817 39 12-08 SCREW .12 X .50
23 532 17 53-31 BUSHING
24 532 19 36-07 BELT GUIDE
25 811 05 05-00 LOCKWASHER 5/16
26 817 49 04-08 SCREW 1/4−20 X .500
KEY PART
NO. NO. DESCRIPTION
27 532 05 92-89 WASHER
28 810 04 05-00 LOCKWASHER 5/16
29 874 61 05-16 SCREW 5/16−18 X 1.00
30 532 40 94-75 SPACER
31 532 18 04-78 ENGINE TRACTION PULLEY
32 532 40 00-26 WASHER
33 532 85 02-63 LOCKWASHER 3/8
34 532 85 10-84 SCREW 3/8−24 X 1.38
35 532 18 77-86 TRACTION IDLER ARM
36 532 18 05-22 IDLER PULLEY
37 874 78 05-20 SCREW 5/16−18 X 1.25
38 873 93 05-00 NUT 5/16−18
39 874 78 05-24 SCREW 5/16−18 X 1.50
40 532 17 53-30 PIN
41 532 19 33-97 IDLER PIVOT BRACKET
42 532 41 99-25 IDLER BRAKE ARM
43 532 08 51-79 RETAINER
44 532 17 88-28 BRAKE SPRING
45 532 16 67-85 NUT 5/16−18
46 532 18 05-23 PULLEY
47 873 80 04-00 NUT 1/4−20
48 532 19 19-95 POP RIVET 1/4 X .475
49 532 19 84-66 CLUTCH CABLE
50 532 19 28-73 TRACTION SPRING
51 532 70 02-79 RETAINER CLIP
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
33
Page 34
REPAIR PARTS DRIVE
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
1
KEY PART
NO. NO. DESCRIPTION
1 532 41 47-71 TORQUE STRAP
2 532 40 78-58 ANTI ROTATE BRACKET
3 532 15 00-78 SCREW 5/16−18 X .750
3
01.01.001-B
2
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
34
Page 35
REPAIR PARTS CHASSIS / ENGINE / PULLEYS
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
5
3
4
5
4
1
6
KEY PART
NO. NO. DESCRIPTION
- - - - - - - - B&S ENGINE MODEL
6
21M414-1182-E1
1 532 41 53-40 FRAME
2
01.00.021-B
2 532 40 37-32 BOTTOM PAN
3 532 40 38-70 ENGINE MOUNT PLATE
4 532 15 04-06 BOLT 3/8−16
5 532 15 00-78 SCREW 5/16−18 X .750
6 532 18 44-71 SCREW 10−24 X .625
1
KEY PART
NO. NO. DESCRIPTION
1 532 40 91-61 COVER ASSEMBLY
2
2 532 17 88-13 PULLEY
3 532 19 23-83 TRACTION BELT
4 532 40 80-19 IMPELLER BELT
01.04.002-B
3
4
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
35
Page 36
REPAIR PARTS WHEELS
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
KEY PART
NO. NO. DESCRIPTION
1
2
01.06.006-A
1 532 42 20-70 WHEEL ASSEMBLY LH
2 532 42 20-69 WHEEL ASSEMBLY RH
KEY PART
NO. NO. DESCRIPTION
1 532 41 52-63 STEER CABLE BRACKET LH
1
2 532 18 78-59 STEER CABLE BRACKET RH
2
01.15.002-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
36
Page 37
REPAIR PARTS WHEELS
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
2
17
20
17
16
20
19
21
2
6
5
4
3
1
01.15.001-A
2
8
7
18
9
10
23
22
15
11
16
18
24
12
21
14
19
22
13
13
14
23
12
11
10
6
7
8
9
3
4
5
2
1
KEY PART
NO. NO. DESCRIPTION
1 532 40 51-61 COVER
2 532 18 44-71 SHOULDER SCREW
3 812 00 00-45 RETAINER RING
4 532 19 21-26 WHEEL DRIVER
5 532 18 24-66 RETAINER RING
6 532 18 76-22 WHEEL LOBE
7 532 19 49-41 CLUTCH SLIDE
8 532 17 91-39 SPRING
9 532 18 92-82 SQUARE KEY
10 532 19 49-40 AXLE LOBE
11 532 17 46-97 THRUST WASHER
12 532 19 95-19 STEERING YOKE
13 532 18 41-97 STEERING BRACKET
14 817 49 05-08 SCREW 5/16−18 X .50
15 532 19 95-11 PIVOT BRACKET
16 532 19 95-18 BELLCRANK
17 532 18 18-47 BELLCRANK PIN
18 817 60 04-06 SCREW 1/4−20 X .375
19 532 40 50-77 STEERING LINK
20 532 70 02-79 RETAINER
21 532 08 51-79 RETAINER
22 532 19 38-85 SPRING
23 532 18 20-15 LEVER PIN
24 532 19 95-12 PIVOT BRACKET
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
37
Page 38
REPAIR PARTS BAG OF PARTS
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
4
14
13
12
3
2
5
8
1
01.14.003-A
7
6
9
KEY PART
NO. NO. DESCRIPTION
1 532 19 85-63 POWER CORD
2 532 16 96-75 RETAINER PIN
11
10
3 532 18 06-84 WRENCH
4 532 18 45-05 REMOTE SPRING
5 532 17 98-29 SHOULDER BOLT 1/4−20
6 532 17 92-46 NYLON WASHER 1/4−20
7 532 19 17-30 LOCKNUT 1/4−20
8 872 25 05-05 CARRIAGE BOLT 5/16−18 X 5/8
9 532 75 11-53 LOCKNUT 5/16−18
10 873 80 06-00 LOCKNUT 3/8−16
11 819 13 13-16 WASHER 3/8
12 532 19 86-36 SHEAR BOLT 1/4−20 X 1−3/4
13 532 19 86-38 SPACER
14 873 80 04-00 LOCKNUT 1/4−20
KEY PART
NO. NO. DESCRIPTION
1
01.14.007-A
1 532 19 30-71 SAFETY IGNITION KEY
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
38
Page 39
REPAIR PARTS DECALS
SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41
KEY PART
NO. NO. DESCRIPTION
1 532 18 10-37 DECAL, DANGER
2 532 42 37-17 DECAL, HUSQVARNA 1330SB-XLSB
3 532 18 10-35 DECAL, DANGER, DEFLECTOR
4 532 18 10-42 DECAL, DANGER
5 532 42 37-16 DECAL, HUSQVARNA 1330SB-XLSB
6 532 18 10-33 DECAL, INSTRUCTION
7 532 18 37-30 DECAL, REMOTE DEFLECTOR
9 532 41 54-75 DECAL, SPEED CONTROL
11 532 41 53-99 DECAL, LH TRIGGER
12 532 41 53-98 DECAL, RH TRIGGER
- - 532 42 35-18 OWNER'S MANUAL, ENGLISH
- - 532 42 35-19 OWNER'S MANUAL, FRENCH
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
39
Page 40
TION
CONSIDERA
TIONS
ARRANTY
AND LIMITA
IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE, AND DOES NO T ASSUME OBLIGATION TO UPDATE
This warranty shall be inapplicable to defects resulting from the following:
SECTION 4: EXCEPTIONS
starter ropes and tiller tines;
(2) Natural discoloration of material due to ultraviolet light;
(3) Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective manufacturer’s
appropriate manufacturer;
(4) Lawn and garden attachments are covered by a third party which gives a warranty, all claims for warranty should be sent
warranty as provided in writing with the product information supplied at the time of purchase; all claims must be sent to the
to the manufacturer,
(5) Commercial or consumer mowing decks with sand abrasion damage.
(6) Emission Control System components necessary to comply with CARB-TIER II and EPA regulations which are
manufactured by third party engine manufacturer.
(1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any
adverse reaction due to incorrect storage or use habits;
safety, or durability, or causes the product to fail to comply with any applicable laws; or:
by Husqvarna;
(3) Alterations or modifications that change the intended use of the product or affects the product’s performance, operation,
(2) Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished
PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE
(4) Additional damage to parts or components due to continued use occurring after any of the above.
DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RESERVES THE RIGHT TO CHANGE OR
PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO THE WARRANTY PERIOD AS
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT
PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PREVIOUSLY MANUFACTURED PRODUCTS.
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and
Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long an implied
The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written in the
not be used, but delivered as is to an authorized Husqvarna retailer for evaluation. Proof of purchase, as explained in
you may also have other rights which vary from state to state.
maintenance section of the Owner’s/Operator’s manual. Should an operational problem or failure occur, the product should
SECTION 5: CUSTOMER RESPONSIBILITIES
It is the Owner’s and Retailer’s responsibility to make certain that the Warranty Registration Card is properly filled out and
section 6, rests solely with the customer.
SECTION 6: PROCEDURE TO OBTAIN W
HUSQVARNA
7349 Statesville Road
Charlotte, NC 28269 2008
To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna
Proof of purchase must be presented to the authorized Husqvarna retailer in order to obtain warranty service. This proof
in order to confirm the warranty and to facilitate post-sale service.
mailed to Husqvarna Forest & Garden Company. This card should be mailed within ten (10) days from the date of purchase
must include date purchased, model number, serial number, and complete name and address of the selling retailer.
delivered at the owner’s expense. Downtime, pick-up and delivery charges are not covered by this warranty. An authorized
Husqvarna retailer can be normally located through the “Yellow Pages” of the local telephone directory or by calling 1-800-
HUSKY62 for a retailer in your area.
retailer in a timely manner, no later than thirty (30) days from date of the operational problem or failure. The product must be
- Zero Turn Riders
THIS WARRANTY
WARRANTY STATEMENT
TIONS UNDER THE WARRANTY
’S OBLIGA
ARRANTY
ARRANTY SCHEDULE FOR TURF CARE Equipment
Lifetime Warranty (“PARTS ONLY” after initial warranty expiration): Ignition coils and modules on handheld product.
Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from
defects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below:
SECTION 1: LIMITED W
W
Lifetime Warranty (Parts and Labor): All tiller tines and trimmer shafts against breakage. Proof of purchase required.
Proof of purchase required.
5 year consumer warranty or 1,500 hours of use.
SCHEDULE FOR CONSUMER TURF CARE EQUIPMENT:
(New warranty applies to units sold after August 1, 2005. Also applies to units factory-equipped with R.O.P.S.
iZ, LZ & BZ Zero Turn Riders:
iZ, LZ & BZ Zero Turn Riders: 5 year commercial warranty or 1,500 hours of use.
EZ Zero Turn Riders: 3 year consumer warranty or 600 hours of use (when used solely at the owner’s residence.)
3 Year or 1,500 Hour Commercial Use Warranty: spindles on zero turn riders, hydraulic pumps and wheel motors.
EZ & MZ Zero Turn Riders: 1 year commercial warranty or 600 hours of use.
ARRANTY
2 Year Consumer Warranty: Automatic mower, all Residential Zero Turn Riders, all lawn, yard and garden tractors, all
warranty. New warranty applies to units sold after August 1, 2005. Also applies to units factory-equipped with R.O.P.S.
2 Year COMMERCIAL and CONSUMER Warranty: all Husqvarna ground-engaging commercial equipment.
W
Warranty Schedule for Turf Care Walk Behind Units - W, WG & WH Zero Turn Riders - 3 year consumer and commercial
noncommercial walk behind mowers, tillers, snow blowers, electrical products and power-assist collection systems for
noncommercial, nonprofessional, noninstitutional or nonincome producing use, except as herein stated. All consumer
product use must have been limited to the owner’s residence.
producing use, except as herein stated. All consumer product use must have been limited to the owner’s residence.
2 Year or 2,000 Hour Powertrain & 1 Year or 1,000 Hour Body Warranty: Husqvarna Utility Vehicles.
2 Year Consumer Warranty: all consumer chain saws, trimmers, brushcutters, clearing saws, handheld blowers, backpack
blowers, hedge trimmers, and electrical products for noncommercial, nonprofessional, noninstitutional or nonincome
WARRANTY SCHEDULE FOR CONSUMER FOREST & GARDEN EQUIPMENT:
hovering trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection systems for
1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-professional,
noninstitutional, non-municipality or non-income producing use. All 300 series trimmers, brushcutters, clearing saws,
Automatic mower, chain saws, 100 series trimmers, power cutters, stump grinders, pole
with a warranty claim form. All care and maintenance instructions must be followed as stated by the manufacturer on the
30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items. Emission control
warranty with product at time of purchase.
commercial, institutional, professional or income producing purposes or use.
1 Year Conditional Component Warranty: Chain saw crankshafts for commercial/professional use (parts and labor).Saw
must be operated with Husqvarna XP 2 cycle oil.
Batteries: 1 year prorated limited warranty with 100% replacement during the first 6 months.
saws, pole pruners, snow throwers, model series 580 & 600 walk-behind mowers, or any Husqvarna product used for
90 Day Commercial Warranty:
commercial, institutional, professional, municipality or income producing purposes or use except as otherwise provided herein.
material and workmanship. Normal wear, tear or abuse is not covered under warranty. Product must be returned to Charlotte
Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer’s original purchase for defects in
located in the back of the Retailer Warranty Policy & Procedure Manual.
Rental Warranty: 90 days on all applicable professional equipment reference warranty time period charts
part of engine systems manufactured by third part engine manufacturers for which the purchaser has received a separate
care label. The fit of the protective apparel/boot is not covered under warranty.
system components necessary to comply with CARB-TIER II and EPA regulations, except for those components which are
Husqvarna will repair or replace defective components without charge for parts or labor if a component fails because of a
defect in material or workmanship during the warranty period.
SECTION 2: HUSQVARNA
SECTION 3: ITEMS NOT COVERED BY
The following items are not covered by this warranty:
(1) Normal customer maintenance items which become worn through normal regular use, including, but not limited to, belts,
blades, blade adapters, bulbs, clutches, clutch drums, filters, guide bars, lubricants, rewind springs, saw chain, spark plugs,
532 42 35-18 Rev.1 11.21.08 SR Printed in U.S.A.
Loading...