www.HunterFan.com 1.888.830.1326
Installation |
|||
|
|
|
r |
|
|
we |
|
|
Po |
OFF |
|
urn |
|
||
T |
|
|
|
|
|
|
Before installing the Universal Remote Control Receiver, use the pull chains to set the fan speed to HIGH and the light to ON. Be sure power is OFF before
proceeding with installation.
Wiring
|
|
|
E |
|
|
|
|
|
|
R C |
|
|
|
|
|
M |
|
E |
|
|
|
|
|
I |
|
||
|
O |
|
|
V |
||
R |
|
|
|
|
E |
|
|
|
|
|
R |
||
F |
|
|
|
|
|
|
|
|
|
|
|
|
Remove the canopy. If uncertain how to remove it, reference the fan’s
owner’s manual. With wiring exposed, it may be helpful to note existing wire connections or take a digital photo for reference. Remove the wire connectors that connect the wires from the outlet box to the fan, leaving the grounding wires connected.
blue |
blue |
yellow |
black |
Universal Ceiling
Fan Remote Control
Model 99116
If you are installing multiple remote-controlled fans on the same circuit breaker,
you may need to perform a few extra steps to prevent interference or faulty operation of your remote controls.
Go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote-controlled fans?” for more information.
For low pro le fans, the receiver should Receiver be secured to the ceiling bracket with a
cable tie.
Receiver |
Ceiling |
|
|
Cable Tie |
|
|
Plate |
|
|
|
|
|
|
|
|
|
Ceiling |
OR |
OR |
Receiver |
OR |
|
Bracket |
|
|
||||
|
|
|
|
|
|
|
|
|
|
Receiver |
Fan Body |
|
|
|
|
|
Canopy
Canopy
Canopy
Choose the hanging system that most closely resembles the one used by your fan and install the receiver as shown and wire as directed.
Note: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire, leaving a minimum of 8” remaining. Re-strip the fan lead wires 1/2”.Place remaining excess wire into the ceiling electrical box. The bracket and fan must remain properly grounded.
You may have installation issues if the fan is installed on an angled ceiling. For assistance, call 1-888-830-1326.
|
O |
R |
|
F |
|
M
FA
N
|
|
MRECEI |
|
|
|
O |
V |
||
R |
|
|
E |
|
|
|
R |
||
F |
|
|
|
M CEILI
black |
black (ungrounded) |
white
|
O |
M |
F |
|
|
|
R |
|
A |
|
|
||
F |
|
|
|
N |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
white |
white (grounded) |
CONNECT WIRES FROM RECEIVER TO FAN - Using the orange wire connectors, connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan. Connect the yellow wire from the receiver to the black wire from the fan.
If you’re uncertain about wire colors or connections, please contact a qualified electrician.
To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
CONNECT WIRES FROM RECEIVER AND FAN TO WIRES FROM OUTLET BOX - Using the orange wire connectors, connect the black wire (ungrounded) from the ceiling to the black wire from the receiver. Connect the white wire (grounded) from the ceiling to both the white wire from the receiver and the white wire from the fan.
AFTER ALL WIRES ARE CONNECTED and secured with wire connectors, re-install the canopy.
Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box.
M0041-01 • 01/15/14 • © Hunter Fan Company