Hunter Engineering Scissor Lift Family Specification Sheet

RX16JFT & RX16FT-PS

Flush Mount Lift Rack

SPECIFICATIONS

RX16FT-PS Shown

Site Specications

Substructure Requirements Refer to 6339-T for full details

Power Requirements 208-230 VAC, single phase power, 26 Amp

Air Supply Requirements

Minimum Concrete Spec. 3 in. (76 mm) thick, 3000 PSI (20,700kPA) rating

Maximum Floor Slope 2 in. (51 mm) over 126 in. (3200 mm)

Max. Vehicle Weight 16,000 lbs. (7257 kg)

Max. Wheelbase

General Service 187 in. (4750 mm)

Two-Wheel Alignment 182 in.(4623 mm)

Four-Wheel Alignment 158 in. (4013 mm)

Alignment Height All lock positions

Min. Four-Wheel Alignment 88 in. (2235 mm)

Lifting Speed 1 speed, 60 seconds

Lowering Speed 2 speed, 25 seconds

Jacks require 125 PSI (8.6 bar) for full capacity

Product Specications

90-150 PSI (6.2-10.3 bar)

MODEL FEATURES / DIMENSIONS

Features

9000-lb Swing Air

Jacks (2)

Two-Speed Lowering

W2

JFT FT-PS

R

H1

Outside Width (W1)

Inside Width (W2)

Length (L)

Runway Width (R)

Raised Height (H1)

Depth (H2)

Dimension

92.5 in.

2350 mm

40 in.

1016 mm

231.375 in.

5877 mm

26 in.

660 mm

72 in.

1829 mm

14.75 to 15.25 in.

375 to 387 mm

W1

For lift rack information visit:

www.hunter.com/lift-racks

H2

For general inquiries visit:

www.hunter.com

or call

800-448-6848

L

Continued on Page 2

For local contact visit:

www.hunter.com/contact-hunter

Form 6491-T, 06-15

Supersedes Form 6491-T, 08-13a

Copyright © 2015, Hunter Engineering Company

RX16JFT & RX16FT-PS

!

WARNING

!

WARNING

!

WARNING

!

WARNING

DRAIN

LOCATED

IN

CENTER

OF PIT

SLOPE

PIT

FLOOR

TOWARD

DRAIN

(1/2")

CONSOLE CONDUIT DETAIL

96 1/2"

(2451 mm)

OPTIONAL CONSOLE

LOCATION

16"
(406
mm)

22"

(559 mm)

6" MIN.*
152 mm()

OPTIONAL 1 1/2 IN. DIA. CONDUIT

FOR COMMUNICATION CABLE

TO ALIGNMENT CONSOLE

HAWKEYE SERIES SENSORS

AND PRONTO SYSTEMS HAVE

SPACE REQUIREMENTS IN
FRONT OF LIFT THAT MUST BE
MET, REFER TO APPROPRIATE

SITE REQUIREMENTS.

ENTIRE PIT

(BOTTOM AND WALLS)

MUST BE HARD

TROWEL FINISH

34 3/4"

(883 mm)

EXTENDER

PLATES

51-2464-1-PPP

AND

RAMPS

147-141-1-PPP

231 3/8"

(5877 mm)

64"

(1626 mm)

33 3/4"

(857 mm)

!

WARNING

STAY BEHIND
YELLOW LINE

WHEN THE

LIFT MOVES.

128-978-2

DECAL 128-978-2

PLACED ON EACH

PERIMETER ANGLE

(4 PLACES)

AND EACH SIDE OF

LIFT (2 PLACES)

!

WARNING

APPROX. 2"

(51 mm)

TYPICAL

ANGLE AROUND PIT

PERIMETER

PAINTED SAFETY

YELLOW

(NOT SUPPLIED BY

HUNTER)

32"

(813 mm)

RAMPS

147-141-1-PPP

OPTIONAL REAR STEP

(6" (152 mm) MAX. HT.)

PIT DEPTH OF

14 3/4" to 15 1/4"

(375 mm to 387 mm)

REQUIRED AT

FRONT END OF PIT

OPT. FRONT STEP

(12" (305 mm)
MAX. DEPTH)

45

6" MIN.

RADIUS

CONDUIT

EXIT FLUSH

WITH

PIT FLOOR

ROUTE 4" MIN DIAMETER

CONDUIT OR EQUIVALENT

CLOSED CHANNEL FROM

PIT FLOOR TO BASE OF

CONSOLE

*

LONGER VEHICLES WILL NEED TO BE SERVICED WITH BAY DOOR OPEN. TO
ACCOMMODATE MOST VEHICLES, INCREASE SPACE BEHIND PIT TO () OR
GREATER.

39" 991 mm

** SITES WITH D.R.W. TRUCK

TRAFFIC SHOULD USE 20" MIN.
CONSOLE TO PIT DISTANCE.

**

15" TO 41"

(381 TO 1041 mm)

VEHICLE APPROACH

BAY DOORBAY DOOR

Flush Mount Lift Rack

SPECIFICATIONS (Refer to 6339-T for substructure construction requirements)

*Non-standard positioning of control console is limited to a maximum space between console and rack of 6 feet
(1829 mm) at the approach ramp end and 17 feet (5182 mm) at the turnplate end. Additional threshold and perhaps
hydraulic hoses will be required (refer to Installation Instruction for details).

All dimensions shown are for nished pit. Accomodate tile thickness as needed.

Supersedes Form 6491-T, 08-13a

Form 6491-T, 06-15

Copyright © 2015, Hunter Engineering Company