Hunter Engineering Quick Tread Specification Sheet
Quick Check Drive Under with Quick Tread
Flush Mounted
Site Specications
Power Requirements
Air Supply Req. (IS Units)
Approximate Air
Consumption
Substructure Specications
Drive Under Quick Check and Flush Mount Quick Tread
Installation
(shown with optional monitor)
OVERALL FOOTPRINT
15 ft.
RECOMMENDED BAY
WIDTH
Pedestal Location
Product Specications
Max. Wheel Weight
Test Entry Speed
Quick Check Cabinet
Quick Check Drive Under
Sensor
Quick Tread
*
Amperage shown is minimal circuit rating. Ɨ Isolated ground recommended.
QUICK TREAD COMMUNICATION CABLES (UP TO 75 ft.)
36 - 96 in. (914 - 2438 mm) from QT1F
Shipping Weight
115/230v, 15 amp* 50/60 Hz 1 ph
90-150 PSI (6.2-10.3 bar)
25 SCFM @ 90 PSI
(648 Lpm @ 6.2 bar)
Refer to Form 6905-T
3500 lb. (1588 kg) per wheel
2 to 8 mph (3-13 km/h)
290 lbs (132 kg)
316 lbs (143 kg)
1723 lbs (455 kg)
Ɨ
4 in.
51 in.
93 in.
(7 ft. 9 in.)
OPTIONAL
PEDESTAL
LOCATION
165 in.
(ACCOMMODATES
VEHICLES WITH
MAXIMUM OF
165 in.
WHEELBASE.)
END OF BAY
TO FRONT
WHEEL STOP:
120 in.
SENSOR
HEIGHT:
10 FT.
RECOMMENDED
BAY LENGTH
28 ft. 4 in.
For inspection information visit:
www.hunter.com/inspection
For general inquiries visit:
www.hunter.com
or call
800 448-6848
Continued on Page 2
For local contact visit:
www.hunter.com/company/ndrep.cfm
Form 6898-T, 05-15a
Copyright © 2015, Hunter Engineering Company
Quick Check Drive Under with Quick Tread
Flush Mounted
QUICK CHECK DIMENSIONS
135 in.
(11 ft. 3 in.)
15 in.
WITHOUT
OPTIONAL
MONITOR
SENSOR PROFILE
16 in.
WITHOUT
OPTIONAL
MONITOR
22 in.
WITH
OPTIONAL
MONITOR
32 in.
QUICK TREAD DIMENSIONS
PEDESTAL
67 1/4 in.
(5 ft. 7 1/4 in.)
23 1/2 in.
26 in.
24 1/2 in.
36 in.
16 1/4 in.
45 1/4 in.
18 in.
WITH
OPTIONAL
MONITOR
See 6429-T for
support structure
details. Mounting
plate dimensions
are provided to
aid fabrication.
It is recommended that a
low clearance warning be
suspended at the entrance
of Drive Under Quick
Check® bays.
26 in.
5 in.
14 7/8 in.
34 1/2 in.
5 in.
17 3/8 in.
between the middle of the
pedestal and nearest edge
PIT & CONDUIT SPECIFICATIONS
END VIEW
QUICK TREAD:
HUNTER
SUPPLIED
QUICK TREAD
SUB-STRUCTURE:
CONTRACTOR
SUPPLIED
96 in. (8 ft.) is the
maximum distance
of Quick Tread. Any
further will reduce max
vehicle test entry speed.
36 to 96 in.
(3 ft. to 8 ft.)
51 in.
93 in.
(7 ft. 9 in.)
SIDE VIEW
Quick Tread’s 3 in. underground
conduit must be routed to the
pedestal according to local
codes. The pedestal can be
placed on either side. Exact
placement of conduit will vary.
Refer to Form 6905-T.
51 in.
46.25 in.
8 in.
12 in.
(min.)
93 in.
88 in.
BAY FLOOR
Form 6898-T, 05-15a
Copyright © 2015, Hunter Engineering Company
Loading...