Hunter Engineering ForceMatch HD, 3203-T, DSP7705, DSP9200, QuickMatch Brochure
...
Wheel Balancer Accessories
Wheel mounting kits & accessories
Why use collets?
Precise wheel balancing relies on two critical conditions:
accurate center mounting and distortion-free clamping
while providing wheel protection. The center of the wheel
must be properly located on the balancer shaft. Hubcentric and lug-centric wheels all use the hub bore as
the center locating position of the wheel. The hub bore
centerline is virtually the same as the lug holes.
Traditional high-taper cones often fail to fit properly
within the bore of the wheel. The actual bore of the wheel
(not the bore chamfer) is where centering takes place
when the wheel is mounted on a vehicle. Many modern
aluminum wheel designs cannot be properly mounted
with traditional cones.
Economy collet kits
No
Obstruction
Seated
Direct-Fit dual-taper collet
The low-taper of a direct-fit, dual-taper collet (versus the
high-taper cone) offers better hub bore contact and prevents
bottoming on the outer hubcap.
Obstruction
Not
seated
Traditional high-taper cone
Hunter's new economy collet kits provide a superior
centering performance when compared to traditional
cones. Dual-sided design reduces the possibility of
damage to challenging assemblies such as plastic
clad wheels.
20-3062-1 – Basic collet kit
Kit includes:
A. 192-237-2 2.01 in. to 2.56 in. (51 mm to 65 mm)
B. 192-238-2 2.47 in. to 3.05 in. (63 mm to 77 mm)
C. 192-239-2 2.99 in. to 3.54 in. (76 mm to 90 mm)
D. 192-240-2 3.68 in. to 4.31 in. (93 mm to 109 mm)
E. 192-241-2 4.27 in. to 4.98 in. (108 mm to 126 mm)
20-2989-1 – Basic collet kit with accessories
Kit includes:
A. 20-3062-1 Basic collet kit [shown above]
B. 46-653-2 1.5 in. offset wheel spacer
C. 175-392-1 6 in. clamping cup with retainer
D. 106-157-2 6 in. clamping protector sleeve
20-3062-1
A
D
20-2989-1
B C
E
A
B C D
2
Premium BullsEye® collet kits
Hunter's BullsEye® kits provide comprehensive coverage for passenger-car and light-truck wheels, including 1-ton
capacity. Features optional centering and wheel protection over basic cone and collet sets.
BullsEye collets and storage are standard on Road Force Touch balancers.
20-2683-1 – BullsEye® collet set
Kit includes:
A. 192-213-1 Cone: 2.10 in. to 2.43 in. (53 mm-62 mm)
B. 192-214-1 Cone: 2.44 in. to 2.79 in. (62 mm-71 mm)
C. 192-215-1 Cone: 2.71 in. to 3.11 in. (69 mm-79 mm)
D. 192-216-1 Cone: 3.05 in. to 3.42 in. (77 mm-87 mm)
E. 192-217-1 Cone: 3.37 in. to 3.74 in. (86 mm-95 mm)
F. 192-218-1 Cone: 3.65 in. to 4.06 in. (93 mm-103 mm)
G. 192-219-1 Cone: 4.05 in. to 4.36 in. (103 mm-111 mm)
H. 192-220-1 Cone: 4.32 in. to 4.70 in. (110 mm-119 mm)
I. 192-221-1 Cone: 4.64 in. to 5.01 in. (118 mm-127 mm)
J. 192-222-1 Cone: 4.96 in. to 5.33 in. (126 mm-135 mm)
20-2765-1 – BullsEye collet & storage kit
[SmartWeight Touch-series]
Kit includes:
A. 175-392-1 6 in. clamping cup
B. 46-653-2 Performance wheel & light truck spacer
C. 14-1470-005 Cone carrier bracket support
D. 56-70-2 Front balancer cone carrier
E. 20-2683-1 Passenger to 3/4 ton dual-taper collet kit
F. 106-157-2 Protector sleeve
20-2683-1
AGB C
20-2765-1
A
E
D E
H
I
C
D
F
J
B
F
BullsEyePro – BullsEye Pro collet & storage kit
[SmartWeight Touch-series]
This kit is the same as the BullsEye kit but includes adjustable
flange plate and stud kit (20-1839-1). [Not shown, see page 5]
20-2747-1 – BullsEye collet & storage kit
[LCD series only]
This kit includes same contents of 20-2765-1 listed above,
except D is substituted with 56-78-2 (fits LCD series balancers).
[Not shown.]
20-2750-1 – BullsEye front balancer cone
carrier (LCD series only)
This kit includes the BullsEye front collet storage tray only.
[Not shown - includes C and D above.]
20-2739-1
Collet storage kit
(Touch series only)
This kit expands the
BullsEye front collet
storage tray to hold
20 direct-fit collets.
Conveniently attaches to
right of standard BullsEye
storage tray.
20-2739-1
3
Standard balancer accessories
Touch / LCD series
wheel balancers
20-2145-1 – Basic Touch / LCD accessory kit
Kit includes:
A. 106-82-2 Sleeve, scratch guard for small cup
B. 175-353-1 Polymer cup (4.5 in. O.D.)
C. 76-433-3 High-torque steel wing nut* †
D. 221-658-2 Hammer heads (4)
E. 46-320-2 Spacer
F. 221-589-2 Weight hammer/pliers
G. 223-68-1 Pressure ring
H. 20-1650-1 Rim tags [GSP9700/RFT only] †
I. 221-659-2 Adhesive weight scraper
J. 65-72-2 Balance calibration weight
K. 233-44-2 Post-cone hook plastic [Not shown.]
20-2145-1
A
F
I
B C
D E
G H
J
DSP balancer accessories
20-842-1 – Basic DSP accessory kit
Kit includes:
A. 221-563-1 Caliper, rim width/internal diameter
B. 214-121-2 Operational placard [DSP9200 only] †
C. 106-82-2 Sleeve, scratch guard for 4.5 in. cup
D. 175-353-1 Polymer cup (4.5 in. O.D.)
E. 76-432-1 Steel wing nut
F. 221-658-2 Hammer heads (4)
G. 46-320-2 Spacer
H. 221-589-2 Weight hammer/pliers
I. 221-659-2 Adhesive weight scraper
J. 223-68-1 Pressure ring
K. 65-72-2 Balance calibration weight
L. 192-86-2 Centering cone, passenger car
[Not shown.]
M. 192-89-2 Centering cone, truck [Not shown.]
DSP series wheel
balancers
20-842-1
A
DSP series wheel
balancers
B
C
D
E
F
G
H
K
I
J
* LCD balancers may be equipped with 76-433-3 wingnut, 76-438-2 QuickNut or AutoClamp feature. † Kit item may vary per balancer model.
4
Loading...