Hubbell 31.350 User Manual

Hubbell Industrial Controls, Inc.

Fixed
Transmitter

Hubbell Radio Remote Control Systems

Spec Sheet 31.350 • May 2000 • New
Replaces Spec Sheet 31120 of June 96

The Hubbell Fixed Transmitter is a microcon­troller transmitter for use with Hubbell micro­controller receivers. The fixed transmitter com­municates to the remote receiver via radio
transmission, eliminating the need for festoon­ing, cabling, etc.

The Fixed Transmitter is housed in a
NEMA␣ 12 surface-mounting console integrat­ing several Hubbell operator interface prod­ucts. The transmitter electronics are essentially
the same as used in the mid-size transmitter.
Internal power supplies are provided for oper­ation from 120V ac or 250V dc. The antenna
mounts remotely and is conected to the trans­mitter by coax cable.

Multispeed/bidirectional operator control can
be via a Type 4211 Mini-Master Switch for
each function controlled by the transmitter. The
compact Mini-Master Switch has an operator
head molded with tough fiberglass reinforced
polyester resin and a stainless steel handle.
The switch is available with up to 5 speed
points per direction. Refer to Specification
Sheet 4211 for additional information.

Other operator interface functions (start/stop,
horn, etc.) use toggle switches, and/or push­buttons & selector switches. Fixed transmitter
consoles are custom designed to meet the us­er’s specific requirements.

HUBBELL

Transmitter Specifications

72 MHz Transmitters 450 MHz Transmitters

Frequency Range 72-76 MHz 406–430, 450–475 MHz
Channel Available per customer license per customer license
Frequency Stability -10 to 60° C ±5ppm ±5ppm

Emission Type 10KOFID 10KOFID
Spurious/Harmonic Output (below carrier) >70db >80db
Output to Antenna 300 mW 300 mW
Effective Radiated Power 150 mW 150 mW (low) / 500 mW (high)
Nominal Range (line of sight) 2000 ft* 2500 ft (low) / 3500 ft (high)*

FCC Identifier LRL922206-72 LRL922206-450
Canada Certificate Number 2259-203-224 2259-203-222

Voltage Requirement 120V ac or 250V dc 120V ac or 250V dc
Battery Usage no battery no battery
Recharge Time no battery no battery

Operating Temperature -22° F to 140°F -30° C to 60° C -22° F to 140°F -30° C to 60° C
Relative Humidity 20% to 90% non - condensing 20% to 90% non - condensing
LED Indicator Flashing: transmitting Flashing: transmitting

Function Lever Switches as required as required
Auxiliary Switches as required as required
Weight with Battery No Battery No Battery

(low) / 1 W (high)

10.25

DROP

R.F.

RUN

E-STOP

APPLY

RELEASE

BRAKE

* The use of “Whip Antennas”, raised 20 to 30 feet above ground level, on both transmitter
and receiver, increases the nominal range to 2 miles.

0.31 DIA.

8.00

11.00

BRIDGEMAGNET

WEST

EASTLIFT

22.75

22.00

23.50

SOUTH

NORTH

XMIT

DOWN

UP

HOISTTROLLEY

HORN

*

*

*

*

*

*

*

4.15

5.25

HUBBELL

Hubbell Industrial
Controls, Inc.

a subsidiary of
Hubbell Incorporated

JPS-500-1M © 2000
Printed in U.S.A.

50 Edwards Street
Madison, Ohio 44057
[phone]
Fax [phone]

4301 Cheyenne Drive
Archdale, NC 27263
[phone]
Fax [phone]

http://www.hubbell-icd.com/radiocontrols/

Hubbell Industrial Control Solutions