Hubbell 31.210 User Manual
Hubbell Industrial Controls, Inc.
Compact
Locomotive
Radio
Control
System
Hubbell Radio Remote Control Systems
Spec Sheet 31.210 • August 2000 • New
Internal Diagnostics
Receiver Cabinet
• Run by microprocessor on internal programs
• Run by microprocessor on commands and I/O
• Power-up diagnostics
• Continuous monitoring
Operational Status Readout
• English language display of status
Controls System Features
• New “Compact” receiver with diagnostic
display module
• New “Compact pneumatics interface with
analog valves for throttle/brake
• For use with any of the Hubbell transmitters,
see Catalog 31.300
Compact Receiver
• Proven rf module and micro I/O module from
radio crane control
• New “E–Stop” board
• New plug-in output interface cards
• Frequency: 72–76 or 450–470 MHz FM
• NEMA 12 enclosure – 24” h x 24” w x 12” d
Pneumatics Cabinet
Compact Pneumatic Interface
• Very compact manifold/valve assembly
• Analog valves for throttle and train-line brake
control
• Analog pressure indicators
• NEMA 12 enclosure – 24” h x 24” w x 12” d
Midsize Transmitter
(See Spec 31.320)
HUBBELL
Outline Drawings
Specifcations
BSS/.250;TPI=28/20;CHSD=.261;TDSF=.2130;TDSC=.2010
25.50
24.00
22.50
MANUAL
REMOTE
T
-S
+S
-OUT
+OUT
MODEL NO.
PT.
SER.
J2J1
WBA4490_ ASSY REV_
VR1
HUBBELL
4301 Cheyenne Drive
Archdale, N.C. 27263
Hubbell Industrial
Controls, Inc.
5V
V.
VR2
978654321
J3
12V
ASSY:
REV:
WBA4491
1
345
HUBBELL
WBA4516
JMP9
J1
MODULE 1
MODULE 2
+5V
1A
B2
5V COM
R4
JMP1
JMP2
JMP3
JMP4
JMP5
JMP6
JMP7
JMP8
+12V
14
R
S
15
GND
1
1
CN2CN1
WBA4528
43A1332313
3424 44A214
2
HUBBELL
WBA4516
JMP9
J4
J3J2
MODULE 3 MODULE 4
1A1A 1A
R5
1515S15
WBA4528
WBA4528
43A1332313
3424 44A214
J4
J3J2
J1
+5V
LED1
+12V
LED2
TB1
GND
+12V
1
WBA4528
+5V
MODULE 1
MODULE 2
MODULE 3 MODULE 4
LED1
+5V
1A
1A1A 1A
B2
5V COM
+12V
R5
R4
LED2
JMP1
JMP2
JMP3
TB1
JMP4
GND
JMP5
JMP6
+12V
JMP7
JMP8
1
+12V
14
R
1515S15
S
15
GND
1
1
CN2CN1
WBA4536
WBA4536
WBA4535
43A1332313
43A1332313
43A1332313
43A1332313
3424 44A214
3424 44A214
3424 44A214
3424 44A214
Cast Hinges With Removable Hinge Pins
Shown With Door Removed
Receiver Cabinet
Weight — 90 lbs.
Pneumatic Cabinet
Weight — 110 lbs.
24.00
22.50
HUBBELL
MODEL NO.
Hubbell/Industrial
Controls, Inc.
4301 Cheyenne Dr.
PT.
Archdale, N.C. 27263
SER.
25.50
24.00
BSS/.250;TPI=28/20;CHSD=.261;TDSF=.2130;TDSC=.2010
Supply Voltage ......................... 12VDC, 24VDC, 36VDC or 72VDC
Internal Power Requirements ........ +11.9–13.1VDC & +4.5–6.5VDC, 24 VDC
Operating Temperature .............. –22°F (–30°C) to 140°F (+60°C)
Alternate Mtg Position
RESET
8.00
Radio Receiver
4.13
Frequency Range ...................... 72–76 MHz or 450–470 MHz
BSS/.250;TPI=28/20;CHSD=.261;TDSF=.2130;TDSC=.2010
Channel Availability .................. as required by user
Frequency Stability .................... ±5 ppm
22.50
24.00
25.50
24.00
WB4520
HUBBELL
BSS/.250;TPI=28/20;CHSD=.261;TDSF=.2130;TDSC=.2010
Sensitivity ................................ 1 µv @ 20 dB quieting
Data Reception ......................... compatible with Hubbell transmitters
Modulation .............................. Manchester II (bi-phase)
Baud Rate ............................... 4800 bps
Message Format ....................... preamble, sync, start flag, address, control, CRC
check code
Control Section
Single board computer consisting of 80C31 controller, 64k EPROM,
EPLD containing circuits for bi-phase decoding
DC Output Section (Electro-mechanical relays)
Panel mounted mother-board to accommodate 4 plug-in relay boards, each with 6 output
relays, for a maximum of 24 ac output relays and 12 sense inputs
Indicators ........................................... LED on each output
Feedback Sensing ............................... opto-isolated input from: AIR PRESSURE,
THROTTLE, BRAKE, FORWARD, REVERSE
relay outputs
Relays................................................ Standard PC board relays
Output Rating...................................... 115/230V ac, 50/60 Hz, 5A resistive;
C
L
Isolation ............................................. 5000V
12/24V dc, 5A resistive
12.00
BSS/.250;TPI=28/20;CHSD=.261;TDSF=.2130;TDSC=.2010
F14 F15F12 F13
F11
F10F9
F7
F8
F1
F2
BSS/.250;TPI=28/20;CHSD=.261;TDSF=.2130;TDSC=.2010
F5
F6
F4F3
HUBBELL
Hubbell Industrial
Controls, Inc.
a subsidiary of
Hubbell Incorporated
JPS-100-1M © 2000
Printed in U.S.A.
MODEL NO.
HUBBELL
Hubbell Industrial
Controls, Inc.
4301 Cheyenne Drive
PT.
Archdale, N.C. 27263
SER.
V.
Right Side View Of Cabinet W/door Closed
50 Edwards Street
Madison, Ohio 44057
(440) 428-1161
Fax (440) 428-7635
4301 Cheyenne Drive
Archdale, NC 27263
(336) 434-2800
Fax (336) 434-2801
DC Output Section (Stepped analog outputs)
Panel mounted mother-board to accommodate 4 plug-in boards, each with 1 analog output.
Indicators ........................................... LED on each of 8 levels
Output Rating ...................................... 0–10V dc, 20mA, in 8 steps
Isolation ............................................. 5000V
“E-Stop” Board
Plug-in PC board (plugs into motherboard of DC Output Section in place of 1 electromechanical relay board)
Indicators ........................................... LED on each of 5 inputs and 1 output
Inputs ................................................ 5 inputs, optically isolated
Isolation ............................................. 5000V
Control Relays (DIN Rail Mounted)
Individual control relays, as required for locomotive functions.
NEMA P300 DC Inductive Rating .......... 5A Continuous at 250VDC Max.
138VA Make & Break Max.
http://www.hubbell-icd.com/radiocontrols/
Hubbell Industrial Control Solutions
Loading...