Huawei H3CSOHOWDR814G, H3CSOHOWDR834G User Manual

DWG Series ADSL2+ Router Quick

t

A

r

r

Installation Manual

1 Appearance

Figure 1 DWG series rear view

2 Packing List

 One DWG series ADSL2+ router
 One power adapter
 One telephone cable
 One Ethernet cable
 One USB cable
 Two screws and two anchors
 One Quick Installation Manual
 One CD
 Certificate of Quality

3 Hardware Installation

3.1 Installing ADSL Line

DSL2+ Wireless Route

Desktop PC

Figure 2 Installing ADSL Line

Two options are available for ADSL line connections:

 Direct connect the ADSL line (same as a regular telephone port) to

the wall telephone line outlet.

 As shown in Figure 2 , Connect the ADSL port and a telephone set

to a splitter, and then the splitter to the wall outlet of telephone line.
Thus you may place phone calls when accessing the Internet.

NoteBook

Telephone por

LINE

Splitte

ADSL PHONE

Telephone

3.2 Connecting to PC or Ethernet

You can use crossover or straight through cables to connect the PC, HUB, or
switch to the MDI/MDIX auto-sensing interface of WDR series ADSL2+ router.

3.3 Connecting the Power Cord

(1) Attach one end of the power cord to the router and the other end to power
outlet. The power cord is accessory of the router.
(2) Observe the LED status one minute later. The following table lists the LEDs
and their normal expected status.

Table 1 LEDs

LED Normal status

Power The LED stays green. Check the power cord connection if the LED stays off.
Link The blinking of the LED indicates the ADSL activation and 20 to 30 seconds later,

the LED stays green.

LAN The green LED stays on. The blinking of the green LED indicates the data

transmission on the Ethernet port.

Diag This LED is off. If this LED turns on, contact the agents for help.

3.4 Configuring to Obtain an IP Address Automatically

Take the operation in the Windows 2000/XP operating system for example. The
steps are as follows:
(1) Click the <Start> button and choose the Settings > Control Panel options.
Double-click on the Network Dial-up Connections icon from the Control Panel
window.
(2) Right-click on the Local Area Connection icon and select the Properties from
the pop-up menu. Next, choose the Internet Protocol (TCP/IP) from the Local
Area Connection Properties tabbed interface and click <Properties> to proceed.
(3) When the Internet Protocol (TCP/IP) Properties interface pops up, select the
Obtain an IP address automatically and Obtain DNS server address
automatically options, then click <OK>.

3.5 Logon

(1) Check the configuration of the proxy server. Disable the proxy server first
when the PC is accessing the Internet through proxy server.
(2) Use the Web browser. Enter http://192.168.1.1 in the address bar (by default,
the IP address of the WDR ADSL2+ router is 192.168.1.1).
(3) Log onto the Web setup manager. A new window appears prompting you to
enter the user name and password. For the first logon, use the default
administrator user name admin with the password admin. The password can be
modified after entering the management interface.

Figure 3 Entering the user name and password

4 Setup

After you log onto the Web page, follow the simple steps to finish the quick
configuration:
(1) Click <Quick Start> from the Navigation bar to the Quick Start window.
Select the PPPoE as the login type, and then input the user name and password
assigned by ISP. You may leave the Service Name box untouched. Then click
<Save Settings> to proceed.

Input the username
and password
assigned by ISP

Figure 4 Setting parameters

(2) Click <Status> from the Navigation bar to enter the Status tabbed page. You
can find that the IP Address item presents an IP address of the public network
instead of the original 0.0.0.0.

Figure 5 Checking status

(3) If you obtain no public IP address, click <WAN Setup> from the Navigation
bar. Then you can view the VPI/VCI value that the system detects automatically.
If the values are incorrect, select the Disable option and input the values
manually. For the correct VPI/VCI value, contact your local ISP.

Figure 6 Checking the VPI/VCI value

At last, click <Save Settings> in the WAN tabbed interface to finish the
configuration.

Figure 7 Save settings

5 Quick Troubleshooting

Table 2 Quick troubleshooting

Symptom Solution

The ADSL
Link LED
stays OFF.

Access to
the Internet
fails.

You forget
the login
password.

Access to
the router
Web pages
fails.

The
modification
on the Web
pages fails
to save.

The RJ-11 telephone cable must be used and connected to the ADSL and
telephone ports correctly.

Make sure that:

1) You have followed all the steps described above and found no
problems.

2) The IP address of your PC is in the range of allocated valid addresses.
To check it, select the Run option from the Start menu. In the pop-up
window, input winipcfg (in Win98 operating system) or ipconfig (in
Win2000/XP operating system) for the IP address checking.

3) You can ping the IP address of the gateway (192.168.1.1).

4) You have performed the correct DNS configuration on your PC.

5) You have disabled the proxy server.

6) The correct VPI/VCI value is set on the WAN Setup window.
Both of the default user name and password are admin. If you have
changed the password but forget it, press the Reset button for 5 seconds
to restore the default settings on the router. Then you can access the Web
page with the default user name and password.
Note: The reset function restores the settings to the factory default
settings.
Make sure that:

1) The LAN LED is ON.

2) The settings of TCP/IP properties are correct.

3) You have entered the correct user name and password.
If you still cannot access the router Web pages, press the Reset button for
5 seconds to restore the default settings.

You need to click <Save Settings> to save every modification that you
have made.