Page 1
07/2016
shredstar X6pro
shredstar X10
OPERATING INSTRUCTIONS
NOTICE D‘UTILISATION
INSTRUCCIONES DE SERVICIO
Page 2
english: Paper shredder HSM shredstar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
français: Destructeur de documents HSM shredstar . . . . . . . . . . . . . . . . . . . . . . . . . 9
español: Destructora de documentos HSM shredstar . . . . . . . . . . . . . . . . . . . . . . . 15
2 HSM shredstar 07/2016
Page 3
english
1 Explanation of symbols and
safety instructions
WARNING
The safety alert sign with the signal
word WARNING and text on a grey back-
ground warns of the risk of serious to
life-threatening injuries.
NOTICE
alerts you to potential property damage.
Note
indicates information for the effective
operation of the machine without risk of
danger.
Risk of combustion!
Do not use cleaning agents or
pressurized air sprays which
contain infl ammable substances,
as they could ignite.
Dangerous for children and
others!
The machine may not be used
by persons (including children
under 14 years of age) with limited physical, sensory or mental capabilities
or with a lack of experience and knowledge,
unless they are supervised by a responsible
person or are instructed by them on the use
of the machine. Children must be supervised to ensure they do not play with the
machine.
Do not leave the document shredder
switched on when it is unattended.
Safety instructions
Before using the machine for the
fi rst time, read the operating
manual, and keep it for later use
and to pass on to any subsequent
users.
Observe all safety instructions onto the
machine.
Risk of injury from sharp
blades.
Never reach into the slot of the
paper feed.
Risk of injury from being pulled
in!
Keep long hair, loose articles of
clothing, ties, scarves, jewellery,
etc. away from feed opening.
Material with the tendency to form
loops, e.g. tapes, strapping material, etc. must not be shredded.
Dangerous mains voltage!
Improper handling of the machine
can lead to an electric shock.
– Check the machine and cable regularly
for damage.
Switch the shredder off if it is
damaged or not working correctly
or before relocating or cleaning it
and disconnect it from the mains.
– Make sure that no water gets into the
shredder. Do not immerse the power
cable or the power plug in water. Never
touch the power plug with wet hands.
– Never pull the plug out of the socket
using the power cable. Always pull out
the plug directly.
07/2016 HSM shredstar 3
Page 4
english
2 Proper use, warranty
The document shredder is intended for
shredding paper and small quantities of CDs/
DVDs and credit cards or store cards.
NOTICE
The paper must not have any large paper
clips attached.
windows, padded envelopes, newspapers,
foils, laminated documents, cardboard, plastic, adhesive or hard materials.
The warranty period for the document shredder is 2 years. This warranty excludes wear,
damage due to improper handling, natural
depreciation, and actions taken by third parties.
Do not insert envelopes with
3 Overview
1 2 3 4 5 6 7
Operating and display elements
Display option:
Ready for operation
Overload
Power
Overload
1 Shredded material container
2 Safety instructions
3 Feed opening for paper
4 Operating and display unit
5 Feed opening for CDs/DVDs and cus-
tomer/credit cards
6 Mains switch
7 Type plate on the underside of the cut-
ting head
R
Operation button
Motor overheats
Bin full
4 HSM shredstar 07/2016
Overheat
Bin full
Reverse button
Page 5
4 Initial start-up 5 Operation
Switching on the shredder
WARNING
Dangerous mains voltage!
Improper handling of the machine can lead
to an electric shock.
• Only use the machine in a dry room
indoors. Never operate the machine in
damp rooms or in the rain.
• Keep the machine, the plug and cable
away from open fi re and hot surfaces.
The ventilation slots must not be blocked
or covered and there must be at least
5 cm space between the shredder and
any wall or furniture.
• Make sure that the power plug is easily
accessible.
• Before you insert the power plug, make
sure that the voltage and frequency
of your power supply comply with the
information on the name plate.
• Set mains switch at rear of paper shredder
to “I”.
• Press the operation button.
The “Ready for operation” indicator
lights up.
Note
Do not use both cutting units at the same
time. Destroy paper and CDs/credit cards
separately.
Shredding paper
Note
You can increase the service life of your
shredder by removing staples from the
paper.
english
• Insert the CD container provided into the
bracket on the inside of the shredded
material container.
• Plug the power supply into a properly
installed socket using the adapter.
• Feed the paper into the centre of the
paper slot. The light barrier starts the
cutting unit automatically. Therefore, with
thin paper strips, make sure the light barrier detects them.
If feed opening is free again, the cut-
ting unit shuts down and the shredder
switches to standby.
07/2016 HSM shredstar 5
Page 6
english
Shredding CDs / DVDs
WARNING
Danger of injury by splinters!
Depending on the type of material, splinters can fl y out of the
cutting unit while shredding CDs
and injure your eyes.
• For this reason, wear protective goggles.
6
LED displays, troubleshooting
Power
Appliance is ready for use.
Overload
Machine is overloaded. You have fed in
too much paper.
The cutting unit runs in reverse for a few
seconds and pushes the paper back out
again.
• If necessary, press the reverse button “R”
to remove the stack of paper.
• Take half the stack of paper.
• Feed the paper in portions.
Overheat The motor has overheated.
• Let the shredder cool down for approx.
30 mins. before using it again.
• Feed in just one CD/DVD in the middle of
the feed opening.
• Empty the CD container at the latest
after shredding 5 CDs. The separate CD
container is in the shredded material container.
Shredding credit cards and store
cards
• Insert credit card in centre of the feed
opening. Dispose of the shredded material
and the waste paper separately.
Switching off the shredder
• Press the operation button.
The “Ready for operation” indicator
goes out.
• Set mains switch at rear of paper shredder
to “0”.
Bin full
The cutting unit is switched off.
NOTICE
Empty the cut material container, immediately because if it is too full, malfunctions
can occur in the cutting system.
There are recessed handles in the housing
top to make it easier for you to lift the cutting
head.
Cutting unit runs continuously
- The light barrier in the paper feed is
blocked with paper. Press the paper
through with a thin strong piece of cardboard.
- The light barrier is soiled with paper dust.
Clean the sensor with air pressure, a dry
paintbrush or a cloth.
For all other malfunctions, check whether the
cutting head is correctly positioned on the
shredded material container before contacting our customer service.
6 HSM shredstar 07/2016
Page 7
english
7 Cleaning and maintenance 8 Disposal / Recycling
Electrical and electronic old
WARNING
Dangerous mains voltage!
Improper handling of the machine can lead
to an electric shock.
Switch the shredder off before
relocating or cleaning it and
disconnect the mains plug.
Service work which requires the
housing covers to be removed
may only be carried out by HSM
Customer Service and service
technicians of our contractual
partners. See page 24 for our customer
service addresses.
gerous to your health and the environment.
Never dispose of old devices in the household waste. Observe the current applicable
regulations and use the collection points for
returning and recycling electric and electronic devices. Dispose of all the packaging
materials also in an environmentally-responsible way.
devices contain a variety of valuable materials, but also hazardous
substances which were required
for function and safety. Incorrect
disposal or handling can be dan-
Clean the document shredder only with
a soft cloth and a mild soap-water solution. However, no water must enter the
equipment.
Oil the cutting unit when
cutting performance
decreases or the device
becomes noisy, or every
time you empty the waste
container. Only use HSM special lubricating
oil for the cutting unit to do this:
• Spray the special cutting unit oil through
the paper feed along the entire width of
the cutting shafts.
• Run the cutting unit backward without
adding paper. To do so, press the R key.
9 Scope of delivery
• Paper shredder in carton packing
• Operating instructions
Acces so ries
• Special cutting block oil 250 ml
order No.: 1.235.997.403
See page 24 for our customer service
addresses.
Paper dust and particles are shaken off.
07/2016 HSM shredstar 7
Page 8
english
10 Technical data
Type X6pro X10
Cutting type Cross cut
Cut size 2 x 15 mm (1/16 x 5/8“) 4.5 x 30 mm (3/16 x 1 1/8“)
Security level DIN 66399
Cutting capacity * (sheets), A4 80 g/m
70 g/m
2
2
Cutting speed 42 mm/s
Intake width 220 mm / 8.7“
Power supply 120 V / 60 Hz
Power consumption
sheets
with max. number of
Weight ?? kg ?? kg
Shredded material container volume 20 l / 5.3 gal
Separate cutting unit for CD/DVD/customer and credit cards
Cutting type Strip cut
Cut size 25 mm
Cutting capacity 1 CD/DVD (max. 1.2 mm thick) or 1 credit card / store card
P-5 / O-1 / T-1 / E-2 P-4 / O-1 / T-1 / E-2
6
7
10
12
160 W
General data
Operating mode Brief operation
Operating time 7 min
Cooling time 45 min
Ambient conditions in operation:
Temperature
Relative humidity
Height above sea-level (MSL)
max. 90 %, without condensation
-10 °C to +25 °C
max. 2,000 m
Size W x D x H 345 x 245 x 385 mm / 13.6“ x 9.6“ x 15.2“
Sound pressure level emissions
55 dB(A) / 62 dB(A)
(Idle running/ load)
* The maximum number of sheets (DIN A4, 70 g/m² or 80 g/m²), fed lengthways, which can be cut in one cycle. The
performance data is determined when the motor is cold and the cutting device is freshly oiled. A weaker mains voltage or
a different mains frequency to the one specifi ed could result in less sheet capacity and increased noise during operation.
The sheet capacity can vary depending on the structure and properties of the paper and on the way it enters.
This document shredder meets the applicable harmonisation legislation of the European Union:
• Low Voltage directive 2014/35/EU
• EMC directive 2014/30/EU
• RoHS directive 2011/65/EU
The EU declaration of conformity can be requested from the manufacturer.
8 HSM shredstar 07/2016
Loading...