v185e/v185es/v185w/v185ws/w185/w185e/W185q
LCD Monitor User’s
Guide
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products
and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or
editorial errors or omissions contained herein.
HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP.
This document contains proprietary information that is protected by copyright. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent of HP.
Hewlett-Packard Company
10955 Tantau Avenue
Cupertino, CA 95014-0770
USA
Copyright © 2010 Hewlett-Packard Development Company, L.P.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited payper-view viewing uses only unless otherwise authorized by Macrovision. Reverse engin eering or disassembly is prohibited.
Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.
Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license.
HP supports lawful use of technology and does not endorse or encourage the use of its products for purposes other than those
permitted by copyright law.
The information in this document is subject to change without notice.
Preface
About This Guide
This guide is intended for anyone who uses the v185e / v185es / v185w / v185ws / w185 / w185e / W185q LCD
Monitor. It describes the monitor’s features, setup, and operation.
The sections are as follows:
y Safety and Maintenance Guidelines
y Setup
y Using the Monitor
y Installing Drivers and Using the Auto-Adjustment Feature
y Technical Support FAQs
y Specifications
y LCD Monitor Quality and Pixel Policy
y Agency Regulatory Notices
Notational Conventions
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These
blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your monitor.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data, and tells you how to
avoid the problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem.
Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the sp ecific
presentation of the warning is mandated by regulatory authority.
3
Safety and Maintenance Guidelines
Important Safety Information
The power cord is designed for use with your monitor. To use a different cord, use only a power source and
connection compatible with this monitor. For information on the correct power cord set to use with your monitor, see
Power Cord Set Requirements
WARNING: To reduce the risk of electric shock or damage to your equipment, do not disable the power cord
grounding feature. The grounding plug is an important safety feature. Connect the equipment to a grounded
(earthed) power outlet.
For your safety, be sure that the grounded power outlet you plug the power cord into is easily accessible to
the operator and located as close to the equipment as possible. To disconnect power from the equipment,
unplug the power cord from the power outlet by grasping the plug firmly. Never pull on the cord.
Before connecting cables, disconnect power from the monitor by unplugging the power cord from the
electrical outlet.
Do not place anything on power cords or cables. Arrange them so that no one can accidentally step on or trip
over them. Do not pull on a cord or cable. When unplugging from the electrical outlet, grasp the cord by its
plug.
CAUTION: To protect your monitor, as well as your computer, connect all power cords for your computer and
its peripheral devices (such as a monitor, printer, or scanner) to a surge protection device such as a power
strip with surge protection or uninterruptible power supply (UPS).
.
Not all power strips provide surge protection; the power strips must be specifically labeled as having this
ability. Use a power strip whose manufacturer offers a damage replacement policy so you can replace your
equipment if surge protection fails.
Safety Precautions
CAUTION: Avoid applying pressure to the LCD screen; doing so can cause damage.
y Use only a power source and connection compatible with this mo nitor, as indicated on the label/back plate
of the monitor.
y Be sure the total ampere rating of the products connected to the outlet does not exceed the current rating
of the electrical outlet, and the total ampere rating of the products connected to the cord d oes not exceed
the rating of the cord. Look on the power label to determine the ampere rating (Amps or A) for each device.
4
y Install your monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the plug
firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.
y Do not allow anything to rest on the power cord. Do not walk on the cord.
Maintenance Guidelines
To enhance the performance and extend the life of your monitor:
y Do not open your monitor cabinet or attempt to service this product yourself. If your monitor is not operating
properly or has been dropped or damaged, contact your HP authorized dealer, reselle r, or service provider.
y Adjust only those controls that are described in the operating instructions.
y Turn your monitor off when not in use. You can substantially increase the life expectancy of your monitor by using a
screen saver and turning off the monitor when not in use.
y Keep your monitor in a well-ventilated area, away from excessive light, heat, or moisture.
y Slots and openings in the cabinet are provided for ventilation. These o penings must not be blocked or
covered. Never push objects of any kind into cabinet slots or oth er openings.
y Unplug your monitor from the wall outlet before cleaning.
y Do not drop your monitor or place it on an unstable surface.
y When removing the monitor pedestal base, you must lay the monitor face down on a sof t area to prevent it from
getting scratched, defaced, or broken.
Cleaning the Monitor
The monitor is a high-quality optical device that requires special care when cleaning. To clean the monitor, follow
these steps:
1 Turn off the computer and the monitor.
2 Unplug your monitor from the wall outlet before cleaning.
CAUTION: Do not use benzene, thinner, ammonia, or any volatile substances to clean the monitor screen or
cabinet. These chemicals may damage the monitor. Do not use liquid cleaners or aerosol cleaners. Never use
water to clean an LCD screen.
3 Wipe the screen with a dry, soft, clean cloth.
• If the screen requires additional cleaning, use an antistatic screen cleaner.
4 Dust the monitor housing. Use a damp cloth to clean the cabinet.
• If the cabinet requires additional cleaning, use a clean cloth dampened with isopropyl alcohol.
5 Plug in the monitor.
6 Turn on the monitor and the computer.
5
Setup
Base and Tilt
Attaching the Base
1 Set the panel face down on a flat , protected surface , such as a table top.
2 Using both hands , align the base with the pedestal and push in firmly to lock in place.
Make sure that the base is securely locked in place before continuing with the setup procedure.
CAUTION: To prevent damage, avoid applying pressure to the panel front.
6
Removing the Base
1 Set the panel face-down on a flat, protected surface.
2 Squeeze the tabs in the bottom of the base to release the lock.
3 Remove the base from the pedestal.
CAUTION: To prevent damage, avoid applying pressure to the panel front.
Adjusting the Tilt
For optimal viewing, adjust the screen tilt to your own preference, as follows:
1 Face the front of the monitor and hold the stand so that you do not topple the monitor while changing the tilt.
2 Adjust the tilt by moving the monitor’s top edge toward or away from you.
CAUTION: To avoid breakage or other damage, do not touch the LCD screen while changing the tilt.
7
Cables
Attaching the Cables
1 Turn off your computer.
2 If you are attaching a VGA cable, connect one end of the 15-pin D-Sub VGA cable (blue connector) to the back of
the monitor and connect the other end to the computer VGA port.
3 If attaching a DVI cable, connect one end of the cable to the back of the monitor and connect the other end to the
computer.
8
4 Connect one end of the power cord to the back of the monitor and plug the other end into a grounded outlet.
5 Turn on your monitor and computer.
If your monitor displays an image, installation is complete. If it does not display an image,
see Technical Support FAQs
and Using the Monitor.
9
Wall Mounting Arm
Preparing to Install a Wall Mounting Arm (Not supplied)
This monitor can be attached to a wall mounting arm that you purchase separately.
CAUTION: Before disassembling the monitor, turn off the monitor power, and disconnect all power, video, and
audio cables.
1 Disconnect the cables from the monitor.
2 With the panel face-down on a protected surface, remove the screws and the pedestal/base att ach ment.
3 Follow the manufacturer’s instructions to assemble the wall mounting arm.
Installing a Wall Mounting Arm
1 Set the monitor screen down on a flat, soft, protected surface.
2 Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the mounting holes in
the back of the monitor.
3 Insert four screws into the mounting holes and tighten.
4 Reconnect the cables. Refer to the user’s manual that came with the wall mounting arm (purchased separately)
for instructions on attaching it to the wall.
10
Using the Monitor
Operating Instructions
Control buttons are located on the front of the panel, as shown below. Use the Menu button (B) to adjust the display
settings to your personal preferences:
y Set up the monitor, attach the cables, and adjust the tilt as described in the Setup
y Press the Power button (E) to turn the monitor on and off. The power indicator lights up when the monitor is on.
y The monitor must be turned on for the other control buttons to work.
y Set the resolution (Setting the Optimal Resolution
y Adjust the onscreen display (OSD) settings (Adjusting On-screen Display Settings
) and adjust the volume (Adjusting the Volume).
section above.
).
11
External Controls
A Auto button Automatically fine-tunes the image quality.
B Menu button Opens, selects, or exits the OSD menu.
C – (minus) button
D + (plus) button
Navigates backward through the OSD menu and decreases adjustment levels.
If the OSD menu is inactive, activates the Volume decrease.
Navigates forward through the OSD menu and increases adjustment levels.
If the OSD menu is inactive, activates the Volume increase.
E Power button Turns the monitor on or off.
F Power LED
Fully powered = green
Sleep mode = amber
Sleep timer mode = flashing amber
See Technical Support FAQs
for more information.
12
Settings
Setting the Optimal Resolution
The recommended resolution for this monitor is 1366 x 768.To con f igure the monitor to this resolution, complete the
setup procedure and make sure that the monitor is connected to the computer. Turn the monitor on and do the
following:
®
1 Click the Windows Start B u tton
2 Under Appearance and Personalization, click Adjust Screen Resolution.
3 Set the resolution slide bar to 1366 x 768.
NOTE: If 1366 x 768 is not shown, download the monitor driver from the Web. See Using the Monitor for instructions.
, and then click Control Panel.
Adjusting the Volume
While the monitor is turned on but the OSD menu is inactive, press the volume increase and decrease (plus and
minus) buttons to adjust volume to the desired level. Volume can range from 0 (mute) to 100. The preset value is 50.
Locking and Unlocking the OSD
To change the lock status of the on-screen display (from locked to unlocked, or from unlocked to locked) press and
hold the Menu button for 10 seconds while the monitor is on. If the OSD is locked, the message “OSD Lock” displays
for 10 seconds.
13
Adjusting On-Screen Display Settings
Use the OSD menu to adjust the screen image and change settings. To access the OSD menu:
1 If the monitor is not already on, press the Power button to turn the monitor on.
2 Press the Menu button to activate the OSD menu.
3 Press the – (minus) and + (plus) buttons to navigate through the functions. Once the desired function is
highlighted, press the Menu button again to activate it. If the selected function has a sub-menu, it displays.
Press – (minus) or + (plus) again to navigate through the sub-menu functions. Once the desired sub-function is
highlighted, press the Menu button to activate it.
4 Press – (minus) or + (plus) to change the settings of the selected function.
5 To exit and save, select the Exit function. If you want to adjust another function, repeat steps 3–4.
NOTE: If the buttons remain untouched for 30 seconds while displaying a menu, new adjustments will be saved and
exit the menu.
14
OSD Menu
The table below shows the OSD menus and their functions at each level.
OSD Menu Levels
Level 1 Level 2 Level 3 Level 4 Factory Preset
Switch Video Input
(w185 / W185q only)
Brightness Adjustment Scale Y
Reset
Cancel
Save and Return
Contrast Adjustment Scale Y
Reset
Cancel
Save and Return
Image Control Auto Adjustment “Adjusting” Message Y
Horizontal Position Adjustment Scale Y
Vertical Position Adjustment Scale Y
Custom Scaling
Clock Adjustment Scale Y
Clock Phase Adjustment Scale Y
Cancel
Fill to Screen
Fill to Aspect Ratio
Save and Return
Color 9300 K
6500 K Y
Custom Color
Adjustment
Custom Color
sRGB
Reset
Cancel
Save and Return
Reset
Cancel
Save and Return
15
OSD Menu Levels (continued)
Level 1 Level 2 Level 3 Level 4 Factory Preset
Quick View Movie
Photo
Gaming
Text Y
Custom
Cancel
Save and Return
Language Deutsch
简体中文
日本語
English English
Español
Français
Italiano
Nederlands
Cancel
Save and Return
Volume(w185 only)
OSD Transparency Adjustment Scale Y
OSD Timeout Adjustment Scale Y
Cancel
Management Power Saver Save and Return Y
Mode Display On / Off Selection Y
DDC/CI Support On / Off Selection Y
Bezel Power LED On / Off Selection Y
Sleep Timer Timer Set Menu Y
OSD
Control(w185 only)
Power-On
Status Display
Default Video Input
(w185 / W185q only)
Horizontal
OSD Position
Vertical
OSD Position
On / Off Selection Y
Analog-VGA
Digital-DVI
Adjustment Scale Y
Adjustment Scale Y
Y
16
OSD Menu Levels (continued)
Level 1 Level 2 Level 3 Level 4 Factory Preset
Cancel
Save and Return
OSD Control
(v185w only)
Horizontal OSD
Position
Vertical OSD
Position
Adjustment Scale
Adjustment Scale
OSD Transparency Adjustment Scale
OSD Timeout Adjustment Scale
Cancel
Save and Return
Information
Factory Reset Yes
No
Exit
Y
Y
Y
Y
17
Installing Drivers and Using the Auto-Adjustment Feature
Downloading Drivers and Software
To download the latest version of drivers and software files from the HP Support Web site:
1 Refer to: http://www.hp.com/support
2 Select your country/region.
3 Select Download Drivers and Software.
4 Enter the model number of your monitor. The software download pages for your monitor will be displayed.
5 Download and install the driver and software files using the instru ctions in the download pages.
Using the Auto-Adjustment Function
Press the Auto button to optimize the screen performance for VGA (analog).
If your monitor is using VGA (analog) input, auto-adjustment can correct the following image quality conditions:
y Fuzzy or unclear focus
y Ghosting, streaking, or shadowing effects
y Faint vertical bars
y Thin, horizontal scrolling lines
y An off-center picture
18
Technical Support FAQs
Technical Support FAQs (Frequently Asked Questions)
Problem & Question Possible Solutions
Power LED is not on. y Make sure the Power button is on and the power cord is properly
connected to a grounded power outlet and to the monitor.
No Plug & Play. y In order for the Plug & Play feature of the monitor to work, you need a
Plug & Play compatible computer and video card. Check with your
computer manufacturer.
y Check the monitor’s video cable and make sure none of the pins are
bent.
y Make sure the HP monitor drivers are installed (HP monitor drivers are
available at: http://www.hp.com/support
)
Picture is fuzzy and has ghosting
shadowing problem.
y Adjust the contrast and brightness controls.
y Make sure you are not using an extension cable or switch box. We
recommend plugging the monitor directly into the video card output
connector on the back of your computer.
y For VGA input, the auto-adjustment function may fix this problem.
Picture bounces, flickers or wave
pattern is present in the picture.
y Move electrical devices that may cause electrical interference as far
away from the monitor as possible.
y Use the maximum refresh rate your monitor is capable of at the
resolution you are using.
Monitor is stuck in “Active Off-Mode”. y The computer power switch should be in the on position.
y The computer video card should be snugly seated in its slot.
y Make sure the monitor’s video cable is properly connected to the
computer.
y Inspect the monitor’s video cable and make sure none of the pins are
bent.
y Make sure your computer is operational by hitting the Caps Lock key
on the keyboard while observing the Caps Lock LED. The LED should
either turn on or off after hitting the Caps Lock key.
19
Technical Support FAQs (Frequently Asked Questions) (continued)
Problem & Question Possible Solutions
Missing one of the primary colors (red,
green, or blue).
Screen image is not centered or sized
properly.
Picture has color defects (white does
not look white).
Unable to set the monitor to the
optimal resolution.
y Inspect the monitor’s video cable and make sure that none of the pins
are bent.
y Make sure the monitor’s video cable is properly connected to the
computer.
y Adjust horizontal and vertical screen position.
y For VGA input, the auto-adjustment function may fix this problem.
y Adjust RGB color or select color temperature.
y Make sure that the graphics card supports the optim al resolution (1366
x 768).
y Make sure that the latest supported driver is installed for the graphics
card. For HP and Compaq systems, you can download the latest
graphics driver for your system from:
http://www.hp.com/support
y For other systems, refer to the Web site for your graphics card.
20
Specifications
All specifications represent the typical specifications provided by HP’s component manufa cturers; actual
performance may vary either higher or lower.
v185e / v185es / v185w / v185ws / w185 / w185e / W185q
Display Type 18.51 inches, TFT LCD 47 cm
Viewable Image Size 18.51 -inch diagonal 47 cm
Tilt –5° to 20°
Face Treatment Antiglare polarizer with hard coating (select
models only)
Maximum Weight (unpacked) 8.47 lb. 3.8 kg
Dimensions (including pedestal)
Height
Depth
Width
Optimum Display Resolution 1366 x 768 (60 Hz)
Text Mode 720 x 400
Dot Pitch 0.3 (H) x 0.3 (V ) mm(v185w/ v185ws/ w185)
13.54 inches
7.05 inches
17.4 inches
0.1 (H) x 0.3 (V) mm(v185e/v185es/
w185e/W185q)
344 mm
179 mm
442 mm
Horizontal Frequency 24 to 83 kHz (v185e / v185es / w185e /
W185q)
30 to 64 kHz (v185w / v185ws / w185)
Vertical Refresh Rate 48 to 76 Hz (v185e / v185es / w185e /
W185q)
50 to 76 Hz (v185w / v185ws / w185)
Audio Power Output 2W / channel @ PC 1 Vrms
Speaker (R/L) 2W / 4 ohm speaker
Power Consumption <30 watts typical(v185w / v185ws / w185)
<33 watts typical(v185e / v185es / w185e /
W185q)
Input Terminal VGA connector or DVI connector
Environmental Requirements
Temperature: Operating
Non-operating
Relative Humidity 20 to 85% (non-condensing)
Power Source 100–240 V∿, 50 / 60 Hz
Altitude: Operating
Non-operating
41 to 95°F
–29 to 140°F
0 to 6,561.68 feet
0 to 40,000 feet
5 to 35°C
–20 to +60°C
0 to 2,000 m
0 to12,192 m
21
Preset Display Modes
Preset
1
2
3
4
5
6
7
8
9
Pixel Format Horz Freq
(kHz)
Horz
Polarity
Vert Freq
(Hz)
Vert Polarity Pixel Clk
(MHz)
Source
640 x 480 31.469 - 59.940 - 25.175 VGA
640 x 480 37.861 - 72.809 - 31.500 VESA
640 x 480 37.500 - 75.000 - 31.500 VESA
720 x 400 31.469 - 70.087 + 28.322 VGA
800 x 600 37.87 + 60.317 + 40.000 VESA
800 x 600 48.077 + 72.188 + 50.000 VESA
800 x 600 46.875 + 75.000 + 49.500 VESA
832 x 624 49.726 + 74.551 + 57.284 MAC
1024x768 48.36
-
60.00
-
65.000 VESA
22
10
11
12
13
1024x768 56.476
1024x768 60.02
-
+
70.069
75.03
+
-
75.000 VESA
78.750 VESA
CVT
1280 x 720
1366 x 768
44.77
-
59.86
+
47.712
-
59.79
+
74.5
0.98M9-R
85.5 CVT
Power Cord Set Requirements
The monitor power supply is provided with automatic line switching (ALS). This feature allows the monitor to operate
on input voltages in the range of 100–240V∿, 50 / 60 Hz, 1.5A.
The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for use in the
country/region where the equipment was purchased.
If you need to obtain a power cord for a different country/region, you should purchase a power cord that is approved
for use in that country/region.
The power cord must be rated for the product and for the voltage and current marked on the pro duct’s electrical
ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked
on the product. In addition, the cross-sectional area of the wire must be a minimum of 0.75 mm² or 18AWG, and the
length of the cord must be between 4.94 ft (1.5 m) and 12 ft (3.6 m). If you have questions about the type of power
cord to use, contact your HP-authorized service provider.
A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it.
Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product.
VGA Pin Assignments DVI Pin Assignments
Pin Number 15-Pin Side of the Signal
Cable
1 Video-Red
2 Video-Green
3 Video-Blue
4 Ground
5 Detect Cable
6 GND-R
7 GND-G
8 GND-B
9 +5V
10 Ground
11 Ground
12 DDC-Serial data
13 H-sync
14 V-sync
15 DDC-Serial clock
23
Plug and Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the
monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional
information about its display capabilities.
The DDC2B is a bi-directional data channel based on the I²C protocol. The host can request EDID information over
the DDC2B channel.
LCD Monitor Quality and Pixel Policy
The HP LCD Monitor uses high-precision technology, manufactured acco rding to high standards, to help guarantee
trouble-free performance. Nevertheless, the display may have cosmetic imperfections that appear as small bright or
dark spots. This is common to all LCD displays used in products supplied by all vendors and is not specific to the HP
LCD Monitor. These imperfections are caused by one or more defective pixels or subpixels.
y A pixel consists of one red, one green, and one blue subpixel.
y A defective whole pixel is always turned on (a bright spot on a dark background), or it is always off (a dark spot on
a bright background). The first is the more visible of the two.
y A defective subpixel (dot defect) is less visible than a defective whole pixel and is small and only visible on a
specific background.
To locate defective pixels, the monitor should be viewed under normal operating conditions and in normal ope rating
mode at a supported resolution and response rate, from a distance of approximately 50 cm (16 in).
We expect that, over time, the industry will continue to improve its ability to produce displays with fewer cosmetic
imperfections, and we will adjust guidelines as improvements are made.
For more information about your v185e / v185es / v185w / v185ws / w185 / w185e / W185q Monitor, refer to the HP
Web site at: http://www.hp.com/support
Agency Regulatory Notices
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfere nce in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
y Reorient or relocate the receiving antenna.
y Increase the separation between the equipment and the receiver.
y Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
y Consult the dealer or an experienced radio or television technician for help.
24
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not
expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain
compliance with FCC rules and regulations.
Declaration of Conformity for Products Marke d with FCC Logo, United State s Only
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
For questions regarding your product, contact:
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 530113
Houston, Texas 77269-2000
Or
call: 1-(800)-474-6836
For questions regarding this FCC declaration, contact:
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 510101
Houston, Texas 77269-2000
Or
call: 1-(281)-514-3333
To identify this product, refer to the part, series, or model number found on the product.
Canadian Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Avis Canadien
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.
25
European Union Regulatory Notice
This product complies with the following EU directives:
y Low Voltage Directive 2006/95/EC
y EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmonized European standards (European
Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard for this product or product
family.
This compliance is indicated by the following conformity marking placed on the product:
26
Disposal of Waste Equipment by Users in Private Households in the European Union
This symbol on the product or on its packaging indicates that this product must not be disp osed of with your other
household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic equipment. The separate collection
and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that
it is recycled in a manner that protects human health and the environment. For more information about where you
can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal
service or the shop where you purchased the product.
Japanese Notice
Japanese Power Cord Notice
27
Japanese Material Content Declaration
A Japanese regulatory requirement, defined by Specification JIS C 0950, 2005, mandates that manufacturers
provide Material Content Declarations for certain categories of electronic products offered for sale after July 1, 2006.
To view the JIS C 0950 material declaration for this product, visit www.hp.com/go/jisc0950.
Korean Notice
Materials Disposal
This HP product contains Mercury in the fluorescent lamp in the display LCD that might require special handling at
end-of-life.
Disposal of this material can be regulated because of environmental considerations. For disposal o r recycling
information, please contact your local authorities or the Electronic Industries Alliance (EIA) (www.eiae.org
).
Chemical Substances
HP is committed to providing our customers with information about the chemical sub stan ce s in our products as
needed to comply with legal requirements such as REACH (Regulation EC No 1907/2006 of the European
Parliament and the Council). A chemical information report for this product can be found
at:http://www.hp.com/go/reach
HP Recycling Program EPA
HP offers product end-of-life return programs for HP and other manufacturers’ hardware in several geographic areas.
The terms and availability of these programs vary by geography because of differences in regulatory requirements
and local customer demand. For information on the HP recycling program, refer to the HP Web site at:
http://www.hp.com/recycle
28
29
Part number: 506356-003
Loading...