HP 6100, StorageWorks 8100, StorageWorks EVA4x00, StorageWorks EVA6x00, StorageWorks EVA8x00 Replacement Instructions Manual

HP StorageWorks
Operator Contro

lPanel

About this document

This document describes the procedure for replacing the Operator
Control Panel (OCP).

replacement instructions

These instructions apply to the EVA4x00/6x00/8x00
products. The part may also be used in other HP
products. See the documentation for your product for
detailed replacement instructions.

© Copyright 2006, 2007 Hewlett-Packard Development Company,
L.P .

Third edi

The information in this document is subject to change without
notice.

Printed in Puerto Rico

www.hp.com

tion June 2007

CAUTION:

This procedure
orlater.IfyouarerunninganearlierversionofXCS,contactyour
HP-authorize
the OCP.

Warranty info

Iftheproductinwhichthispartisbeingreplacedisstillunder
HP warranty, then the replacement part(s) referred to in these
Replacement Instructions is provided under the terms and conditions
of the Hewlett-Packard Company Limited Warranty for that
product. A copy of this Limited Warranty may be viewed at:

ttp://h18006.ww w1.hp.com/products/storageworks/warranty. htm l

h

If this is a trade sale part (product out of warranty), then the replacement
part(s) referred to in these Replacement Instructions is provided under
HP's express limited warranty statement, which may be viewed at:

ttp://customerops.corp.hp.com/1sw/pdm_om/warranty_support/

h
policies/2330100.doc

The replacement part takes on either the Limited Warranty Period of the
part being replaced or a ninety-day period that begins upon installation
of the replacement part, whichever is greater.

The only warranty for this replacement product is as noted above.
Nothing in these replacement instructions should be construed as
constituting an additional warranty. The information provided in these
replacement instructions is provided "AS IS" and HP is not liable for
technical or editorial errors or omissions contained herein.

Before

e the following precautions when replacing the OCP:

Observ

• Removi

• Parts can be damaged by electrostatic discharge. Use proper

• UsecarewhenreplacingtheOCPtoavoiddamagingtheenclosure.

ng the OCP significantly changes the air flow within the
enclosure. The OCP must be installed for the enclosure to cool
properly. If the OCP fails, leave it in place in the enclosure until a
new OCP is available to install.

anti-static protection.

assumes the storage system is running XCS 6.000

d service representative for assistance in replacing

rmation

you begin

697-6792*

*5

Removing the OCP

1. Remove the front panel (1, Figure 1) by grasping the panel at each

end pulling it off the enclosure.

2. Press the OCP latch (2) and swing the panel out until it is fully open.

CAUTION:

Handle the OCP by its metal frame only. This will ensure that the
electronic components are not damaged by static discharge.

3. Grasp the OCP by its metal frame and pull it out of the enclosure

(3).

Page 1

2

Figure 1 Removing the OCP

3

1

0142b

Installing t

1. Slide the new OCP into the enclosure (1, Figure 2).

2. Close the OCP until the latch engages.

3. Install the

NOTE:

After installing the OCP, the controller may have to upgrade the
OCP firmware. Do not remove the OCP while this operation is in
progress. When the OCP is displaying the alternating Storage
System Name and WWID, the correct firmware has been loaded
on the OCP.

Figure 2 Installing the OCP

he OCP

front panel, pressing it firmly into place.

1

0143b

Verifying proper operation

After replacing the OCP, verify that it is operating p roperly:

1. Check the display. It will typically display the default information

which alternates between the Storage System Name and the World
Wide Name.

2. Press any push button. The Storage System Menu Tree should be

displayed.

Returning the failed component

w the return instructions provided with the new component.

Follo

Page 2