HP RP36000/3, RP12000/3 Datasheet

Page 1

Can you meet your power protection needs?

Power protection in your data center has always been a critical requirement to maintain system uptime and keep a dynamic business running. Today, the increased densities in data centers drive the need for uninterruptible power with increased power density, power efficiency and flexibility. The HP RP36000/3 Uninterruptible Power System provides all three.

This pre-racked uninterruptible power system (UPS) provides 36 kilowatts (kW) of power or 24 kW with N+1 redundancy. Housed in a single HP 10000 G2 Series 42U rack, the system can be expanded to 60 kW with N+1 simply by installing up to three additional RP12000/3 UPS Modules. Digital Signal Processing (DSP), UPS paralleling and new Online On Demand hybrid technology answer the call for increased density, redundancy, efficiency and flexibility.

Online On Demand combines the efficiency of a line-interactive UPS, up to 97 percent, with the stability of a double conversion online UPS when power fluctuates beyond acceptable limits. Hot-swappable batteries and electronics modules and an automatic bypass reduce downtime for maintenance.

Key features and benefits

The new HP RP36000/3 Uninterruptible Power Systems are designed to provide high power output with industryleading efficiency for mission-critical enterprise solutions and data centers.

Performance

• Supports up to 60000 volt-amperes (VA)/60000 watts in a single 42U rack

• Offers unity power factor, which means volt amperage out equals wattage output

• Delivers industry-leading 97 percent efficiency, even at output loads as low as 40 percent, with Online On Demand hybrid technology

• Uses UPS paralleling for redundancy and expansion

• Delivers extra long battery life with Enhanced Battery Management (EBM)

• Extends battery run time with optional Extended Runtime Modules (ERMs)

• Enables longer run time with Digital Signal Processing technology (DSP)

HP 3 Phase Parallel Uninterruptible Power Systems

Data sheet

Efficiency, modularity and redundancy give HP 3 Phase Parallel Uninterruptible Power Systems the ability to grow with your data center needs, with lower energy costs and cooling needs than conventional large uninterruptible power systems.

Page 2

Management

• Includes UPS Management Module for remote configuration and graceful shutdown of critical servers without the need for a dedicated management server

• Includes hot-swappable electronics and batteries

• Is backed by a limited three-year warranty and HP pre-failure warranty on the batteries

Redundancy

• Offers N+1 redundancy with UPS paralleling technology

• Allows up to six UPS modules to work together to increase load capacity and N+1 fault tolerance

• In the event of a failure, the load shifts to remaining modules to provide 100 percent UPS protection

Options

• Allows you to attach up to four 3U Extended Runtime Modules to each UPS for increased run time in the event of a power failure

• Supports output modules with dual L15-30 receptacles that can be connected to each UPS module for a total of 12 L15-30 connections

• Fully compatible with the HP Power Distribution Rack to provide power and scalability to rows of equipment

Ideal environments

Large data centers

The HP 3 Phase Parallel UPS can provide you with additional power protection for multiple racks of critical equipment in the event of a power outage, with better efficiency than many site-level UPS systems.

Small to midsize data centers

When hundreds of kilowatts of power are not necessary, the HP 3 Phase Parallel Uninterruptible Power System provides power protection for an entire row of racks. Its unique modular design allows your system to grow with demand. Hot-swappable electronics and batteries reduce downtime.

Collocation facilities

The HP 3 Phase Parallel UPS can provide power protection to one or more racks and can be managed by administrators separately from the collocation facilities.

Recommended options

RP12000/3 UPS Module AF436 (NA) and AF437 (INTL)

Based on the R12000/3, this UPS is specially designed to attach directly to the bus bar in the RP36000/3, allowing it to expand to 60 kW with N+1 redundancy.

HP Power Distribution Rack

The HP Power Distribution Rack (PDR) improves power management in the data center by moving power distribution to the row level. Decentralizing power improves cable management, decreases diagnostic time for problems, and saves installation costs by reducing the size and number of long power feeds required to reach from large wall-mounted distribution units. Capable of high amperage inputs, the HP PDR can power several high-density racks with shorter cable runs than conventional site-level power distribution systems. Fully redundant inputs and outputs provide dependable power while protecting valuable IT equipment. Individual branch circuit monitoring and redundant management modules provide the status and power consumption of each attached rack.

HP Power Distribution Units AF504A, AF503A, AF508A and AF507A

The monitored vertical rack-mount power distribution units (PDUs) units can connect directly to the optional UPS output modules and provide three-phase monitored power, as well as full-rack power utility ranging from

8.6 kilovolt-amperes (kVA) up to 22 kVA. Available PDUs include full-rack models with 39 receptacles or with 78 receptacles.

HP 3 Phase Modular Power Distribution Units AF512A and AF513A

These high-output, 8.6 kVA (North America/Japan) and 11 kVA (International) Modular PDUs have a unique modular architecture designed specifically for data center customers who want to increase power distribution and space efficiencies in the rack. Modular PDUs consist of two building blocks: the Control Unit (core) and the optional Extension Bars (sticks). The Control Unit is 1U/0U, and the optional Extension Bars mount directly to the frame of the rack in multiple locations.

Page 3

General characteristics

Power rating (non-redundant)

Power rating N+1

Efficiency

Heat dissipation

Cooling

Altitude before derating

Input characteristics

Input connection

Input voltage

Voltage range

Frequency range

Input current distortion

Input power factor

Inrush current

Input requirements

Bypass source

Generator compatibility

Output characteristics

Output connection

Rated output voltage

Output configuration

Output frequency (nominal)

Frequency regulation

Load power factor range

Total output voltage distortion

Battery characteristics

Battery type

Battery run time (internal)

Battery string voltage

Battery test

Battery recharge profile

Battery cut-off voltage

Battery low condition

Extended battery capability

36 kW / 36 kVA

24 kW / 24 kVA

>97%

<1113 W / 3800 BTU/hr. at 100% rated load

Fan-cooled, temperature microprocessor monitored; front air entry, rear exhaust

1000 meters (3300 ft. ASL)

Hard-wired from facility power

208 VAC and 400 VAC models

208V model: 180 to 265 VAC (N.A.) 400V model: 311 to 519 VAC (Intl.)

50 or 60 Hz, ±5 Hz (auto-sensing)

<5% with IT loads (PFC power supplies)

>.99 with IT loads (PFC power supplies)

Load dependent

Hard-wired, three-phase, wye (5 wire, 4 pole)

Same as input (single-feed)

Fast sync slew rate for generator synchronization

Hard-wired from power bus bar or uses optional output modules

208V model: 180 to 255 VAC, Ph to Ph 400V model: 180 to 240 VAC, Ph to N

Three-phase, wye. Three-phase Delta can be provided by optional output modules

50 or 60 Hz auto-detection on startup

0.1 Hz free-running

Lagging: 0.7 Leading: 0.9

<3% with IT loads (PFC power supplies) <5% with non-linear or non-PFC power supplies

Maintenance-free, sealed, valve-regulated lead acid (VRLA)

>5 minutes at 100% load

240 VDC

Automatic battery test standard Manual battery test from front display

Enhanced Battery Management three-stage charging technology

Variable from 1.67 VPC at <5 min. run time to 1.75 VPC at >90 min. run time

Announced with alarm

Yes, add up to four additional 3U battery enclosures per RP12000/3 UPS Module

12 kW / 12 kVA

60 kW / 60 kVA maximum configuration

>97%

<371 W / 1266 BTU/hr. at 100% rated load

Fan-cooled, temperature microprocessor monitored; front air entry, rear exhaust

1000 meters (3300 ft. ASL)

Connects to power bus bar

208 VAC and 400 VAC models

208V model: 180 to 265 VAC (N.A.) 400V model: 311 to 519 VAC (Intl.)

50 or 60 Hz, ±5 Hz (auto-sensing)

<5% with IT loads (PFC power supplies)

>.99 with IT loads (PFC power supplies)

Load dependent

Hard-wired, three-phase, wye (5 wire, 4 pole)

Same as input (single-feed)

Fast sync slew rate for generator synchronization

Hard-wired from power bus bar or uses optional output modules

208V model: 180 to 255 VAC, Ph to Ph 400V model: 180 to 240 VAC, Ph to N

Three-phase, wye. Three-phase Delta can be provided by optional output modules

50 or 60 Hz auto-detection on startup

0.1 Hz free-running

Lagging: 0.7 Leading: 0.9

<3% with IT loads (PFC power supplies) <5% with non-linear or non-PFC power supplies

Maintenance-free, sealed, valve-regulated lead acid (VRLA)

>5 minutes at 100% load

240 VDC

Automatic battery test standard Manual battery test from front display

Enhanced Battery Management three-stage charging technology

Variable from 1.67 VPC at <5 min. run time to 1.75 VPC at >90 min. run time

Announced with alarm

Yes, add up to four additional 3U battery enclosures per RP12000/3 UPS Module

RP36000/3 (base unit) RP12000/3 (optional UPS expansion module)

Technical specifications

Page 4

To learn more, visit www.hp.com/products/ups

4AA1-5885ENW, November 2007

© 2007 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

HP Financial Services

HP Financial Services provides innovative financing and financial asset management programs to help you cost-effectively acquire, manage and ultimately retire your HP solutions. For more information, contact your local HP representative, or visit

www.hp.com/go/hpfinancialservices

For more information

For more information about HP power distribution products, contact your local HP representative or visit

www.hp.com/products/ups

Physical characteristics

Dimensions (HxDxW) UPS

Total chassis weight without batteries or electronics

Total chassis weight with batteries or electronics

EBM weight

Communications and user interface

Software compatibility

Control panel LCD

Multi-language

Configuration changes

REPO port

Warranty and serviceability

Warranty (parts/labor/onsite)

Serviceability features

CarePacks

Certifications

Safety

EMI

Surge protection

Hazardous materials (RoHS)

78.7 x 39.7 x 24 in.

2000 x 1015 x 597 mm (HP 10000 G2 42U Rack)

653 lb. (296 kg)

1274 lb. (578 kg)

170 lb. (77 kg)

UPS ships with HP UPS Management Module

Two lines by 20 characters Four menu-driven interface buttons Four status-at-a-glance LEDs 1 per UPS Module

English standard

User-capable, firmware autoconfigures

Yes

3-year/1-year/1-year (Power bus bar is 3-year parts only)

Hot-swappable batteries Hot-swappable electronics module Automated internal maintenance bypass Autoconfigure firmware Flash firmware upgradeable

Installation CarePacks available for additional RP12000/3 UPS Modules

208V model: UL1778, cUL 400V model: CE

208V model: FCC Part15 Class A 400V model: EN62040-2 Class A

ANSI C62.41, Cat B-3

EU Directive 2002/95/EC Category 3 (4 of 5)

10.3 (6U) x 17.4 x 26.0 in. 267 x 442 x 660 mm

100 lb. (46 kg)

307 lb. (140 kg)