Bluetooth is a trademark owned by its
proprietor and used by Hewlett-Packard
Company under license. Microsoft and
Windows are U.S. registered trademarks of
Microsoft Corporation. SD Logo is a
trademark of its proprietor.
The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
First Edition: May 2010
Document Part Number: 608573-001
Product notice
This user guide describes features that are
common to most models. Some features
may not be available on your computer.
To obtain the latest information in the HPNotebook PC User Guide, go to the HP Web
http://www.hp.com/support.
site at
Safety warning notice
WARNING!To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact
the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International
Standard for Safety of Information Technology Equipment (IEC 60950).
iii
iv Safety warning notice
Table of contents
1 Getting started
Starting HP QuickWeb ......................................................................................................................... 2
Disabling and enabling HP QuickWeb ................................................................................................. 3
2 Hardware features
Identifying the hardware ....................................................................................................................... 4
Top components .................................................................................................................. 5
Video .................................................................................................................................................. 38
Main menu ......................................................................................................................... 97
Security menu .................................................................................................................... 97
System Configuration menu .............................................................................................. 98
Diagnostics menu .............................................................................................................. 98
Index ................................................................................................................................................................... 99
ix
x
1Getting started
Your computer's main operating system is Windows®. Your computer may also feature HP QuickWeb
(select models only).
The Microsoft®. Windows operating system displays the desktop on the display and controls your
●
computer's hardware, peripherals, and software programs.
If your computer includes QuickWeb, it allows you to quickly browse the Internet, view digital
●
photos, listen to music, or keep in touch using e-mail, instant messages, or Skype, without having
to start your main operating system.
1
Starting HP QuickWeb
To start HP QuickWeb:
1.Select Start > All Programs > HP QuickWeb. Then click HP QuickWeb Configuration Tool.
2.Click Go to shut down Windows and go to QuickWeb.
If you enabled QuickWeb to launch upon computer startup, to start HP QuickWeb:
1.Turn on your computer. The HP QuickWeb screen opens.
2.Click an icon on the HP QuickWeb screen to start a program.
To start HP QuickWeb from Microsoft Windows:
Select Start, click the arrow next to the Shut down button, and then click Restart. Your computer
▲
restarts and displays the HP QuickWeb home page.
NOTE:You can access the software Help when you are in HP QuickWeb by clicking the Help icon in
the notification area of the system tray.
NOTE:Although fn+f12 enables or disables the TouchPad, the system does not display TouchPad
icons in the notification area of the system tray, while you are using HP QuickWeb.
2Chapter 1 Getting started
Disabling and enabling HP QuickWeb
To disable or reenable HP QuickWeb from within the Windows operating system:
1.Select Start > All Programs > HP QuickWeb. Then click HP QuickWeb Configuration Tool.
2.Select the Status tab.
3.Select the Enable HP QuickWeb to automatically launch upon computer start-up check box.
4.Click OK.
NOTE:The HP QuickWeb Configuration Tool can also be accessed by selecting Start > Control
Panel, and then clicking the View by arrow. Select Large icons or Small icons to locate the HP
QuickWeb Configuration Tool.
Disabling and enabling HP QuickWeb3
2Hardware features
Identifying the hardware
Components included with the computer may vary by region and model. The illustrations in this chapter
identify the standard features on most computer models.
To see a list of hardware installed in the computer:
1.Select Start > Control panel > System and Security.
2.In the System area, click Device Manager.
You can also add hardware or modify device configurations using Device Manager.
4Chapter 2 Hardware features
Top components
TouchPad
ComponentDescription
(1)TouchPadMoves the pointer and selects or activates items on the
screen.
(2)Left TouchPad buttonFunctions like the left button on an external mouse.
(3)Right TouchPad buttonFunctions like the right button on an external mouse.
(4)TouchPad scroll zoneScrolls up or down.
This table describes factory settings. To view or change pointing device preferences, select Start > Devices and Printers.
Identifying the hardware5
Lights
ComponentDescription
(1)Caps lock lightOn: Caps lock is on.
(2)Power light
(3)Wireless light
On: The computer is on.
●
Blinking: The computer is in the Sleep state.
●
Off: The computer is off or in Hibernation.
●
On: An integrated wireless device, such as a
●
wireless local area network (WLAN) device
and/or a Bluetooth
Off: All wireless devices are off.
●
NOTE: On some models, the wireless light is
amber when all wireless devices are off.
®
device, is on.
6Chapter 2 Hardware features
Buttons
ComponentDescription
(1)Power button*
(2)Wireless buttonTurns the wireless feature on or off but does not create a wireless
*This table describes factory settings.
When the computer is off, press the button to turn on the
●
computer.
When the computer is on, press the button briefly to initiate
●
Sleep.
When the computer is in the Sleep state, press the button
●
briefly to exit Sleep.
When the computer is in Hibernation, press the button briefly
●
to exit Hibernation.
®
If the computer has stopped responding and Windows
procedures are ineffective, press and hold the power button for at
least 5 seconds to turn off the computer.
To learn more about your power settings, select Start > Control
Panel > System and Security > Power Options.
connection.
NOTE: To establish a wireless connection, a wireless network
must already be set up.
shutdown
Identifying the hardware7
Keys
ComponentDescription
(1)esc keyDisplays system information when pressed in
combination with the fn key.
(2)fn keyExecutes frequently used system functions when
pressed in combination with a function key.
(3)
(4)Windows applications keyDisplays a shortcut menu for items beneath the
(5)Function keysExecute frequently used system functions when
Windows® logo key
Displays the Windows Start menu.
pointer.
pressed in combination with the fn key.
8Chapter 2 Hardware features
Front components
ComponentDescription
(1)Speakers (2)Produce sound.
(2)Battery light
(3)Drive lightBlinking: The hard drive or flash drive is being
On: A battery is charging.
●
Blinking: A battery that is the only available
●
power source has reached a low battery level.
When the battery reaches a critical battery level,
the battery light begins blinking rapidly.
Off: If the computer is plugged into an external
●
power source, the light turns off when all
batteries in the computer are fully charged. If the
computer is not plugged into an external power
source, the light stays off until the battery
reaches a low battery level.
accessed.
Identifying the hardware9
Right-side components
ComponentDescription
(1)Digital Media SlotSupports the following optional digital card formats:
(4)External monitor portConnects an external VGA monitor or projector.
(5)RJ-45 (network) jackConnects a network cable.
Produces sound when connected to optional powered
stereo speakers, headphones, earbuds, a headset, or
television audio. Also connects an optional headset
microphone.
NOTE: When a device is connected to the jack, the
computer speakers are disabled.
The audio component cable must have a 4-conductor
connector.
10Chapter 2 Hardware features
Left-side components
ComponentDescription
(1)Security cable slotAttaches an optional security cable to the computer.
(2)Power connectorConnects an AC adapter.
(3)VentEnables airflow to cool internal components.
NOTE: The security cable is designed to act as a
deterrent, but it may not prevent the computer from
being mishandled or stolen.
NOTE: The computer fan starts up automatically to
cool internal components and prevent overheating. It
is normal for the internal fan to cycle on and off during
routine operation.
(4)USB port Connects an optional USB device.
(5)HDMI portConnects an optional video or audio device, such as
a high-definition television, or any compatible digital
or audio component.
NOTE: Depending on your computer model, the
computer may include an HDMI port or a USB port at
this location.
Identifying the hardware11
Display components
ComponentDescription
(1)Internal display switchTurns off the display if the display is closed while the
power is on.
(2)Webcam lightOn: The webcam is in use.
(3)WebcamCaptures still photographs and videos.
NOTE: To capture videos, you must install additional
webcam software.
(4)Internal microphoneRecords sound.
12Chapter 2 Hardware features
Bottom components
ComponentDescription
(1)Battery release latches (2)Release the battery from the battery bay.
(2)Battery bayHolds the battery.
(3)Vents (4) Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(4)Hard drive bayContains the hard drive, the wireless LAN module slot, and
the memory module slot.
CAUTION: To prevent an unresponsive system, replace
the wireless module only with a wireless module authorized
for use in the computer by the governmental agency that
regulates wireless devices in your country or region. If you
replace the module and then receive a warning message,
remove the module to restore computer functionality, and
then contact technical support through Help and Support.
Identifying the hardware13
Wireless antennas
ComponentDescription
(1)WLAN antennas (2)*Send and receive wireless signals to communicate with wireless
local area networks (WLANs).
(2)WWAN antennas (2) (select models only)*Send and receive wireless signals to communicate with wireless
wide-area networks (WWANs).
*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around
the antennas free from obstructions.
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and EnvironmentalNotices that applies to your country or region. These notices are located in Help and Support.
14Chapter 2 Hardware features
Additional hardware components
ComponentDescription
(1)Power cord*Connects an AC adapter to an AC outlet.
(2)Battery*Powers the computer when the computer is not plugged into
external power.
(3)AC adapterConverts AC power to DC power.
*Batteries and power cords vary in appearance by country or region.
Identifying the hardware15
Identifying the labels
The labels affixed to the computer provide information you may need when you troubleshoot system
problems or travel internationally with the computer.
Service tag—Provides important information including the following:
●
Product name (1). This is the product name affixed to the front of your computer.
◦
Serial number (s/n) (2). This is an alphanumeric identifier that is unique to each product.
◦
Part Number/Product number (p/n) (3). This number provides specific information about the
◦
hardware components of the product. The part number helps a service technician to determine
what components and parts are needed.
Warranty period (4). This number describes the duration (in years) of the warranty period for
◦
this computer.
Model description (5). This is the alphanumeric identifier you use to locate documents, drivers,
◦
and support for your computer.
Have this information available when you contact technical support. The service tag label is affixed
to the bottom of the computer.
®
Microsoft
●
Product Key to update or troubleshoot the operating system. This certificate is affixed to the bottom
of the computer.
Regulatory label—Provides regulatory information about the computer, including the following:
●
◦
◦
The regulatory label is affixed inside the battery bay.
Certificate of Authenticity—Contains the Windows® Product Key. You may need the
Information about optional wireless devices and the approval markings of some of the
countries or regions in which the devices have been approved for use. An optional device may
be a wireless local area network (WLAN) device. You may need this information when
traveling internationally.
The serial number of your HP Mobile Broadband Module.
16Chapter 2 Hardware features
3Wireless and local area network
Using wireless devices
Wireless technology transfers data across radio waves instead of wires. Your computer may be
equipped with one or more of the following wireless devices:
Wireless local area network (WLAN) device—Connects the computer to wireless local area
●
networks (commonly referred to as Wi-Fi networks, wireless LANs, or WLANs) in corporate offices,
your home, and public places such as airports, restaurants, coffee shops, hotels, and universities.
In a WLAN, each mobile wireless device communicates with a wireless router or a wireless access
point.
HP Mobile Broadband Module—A wireless wide area network (WWAN) device that provides
●
access to information wherever mobile network operator service is available. In a WWAN, each
mobile device communicates to a mobile network operator’s base station. Mobile network operators
install networks of base stations (similar to cell phone towers) throughout large geographic areas,
effectively providing coverage across entire states, regions, or even countries.
®
Bluetooth
●
devices such as computers, phones, printers, headsets, speakers, and cameras. In a PAN, each
device communicates directly with other devices, and devices must be relatively close together—
typically within 10 meters (approximately 33 feet) of each other.
Computers with WLAN devices support one or more of the following IEEE industry standards:
802.11b, the first popular standard, supports data rates of up to 11 Mbps and operates at a
●
frequency of 2.4 GHz.
802.11g supports data rates of up to 54 Mbps and operates at a frequency of 2.4 GHz. An 802.11g
●
WLAN device is backward compatible with 802.11b devices, so they can operate on the same
network.
802.11a supports data rates of up to 54 Mbps and operates at a frequency of 5 GHz.
●
NOTE:802.11a is not compatible with 802.11b and 802.11g.
802.11n supports data rates of up to 450 Mbps and may operate at 2.4 GHz or 5 GHz, making it
●
backward compatible with 802.11a, b, and g.
For more information on wireless technology, refer to the information and Web site links provided in
Help and Support.
device—Creates a personal area network (PAN) to connect to other Bluetooth-enabled
Using wireless devices17
Identifying wireless and network status icons
IconNameDescription
Wireless (connected)Identifies the location of the wireless lights and the wireless
buttons on the computer. Also identifies the HP Wireless
Assistant software on the computer and indicates that one or
more of the wireless devices are on.
Wireless (disconnected)Identifies the HP Wireless Assistant software on the
computer and indicates that all of the wireless devices are
off.
HP Connection ManagerOpens HP Connection Manager, which enables you to create
a connection with an HP Mobile Broadband device (select
models only).
Wired network (connected)Indicates that one or more network drivers are installed, and
one or more network devices are connected to a wired
network.
Wired network (disabled/disconnected)Indicates that one or more network drivers are installed, but
no network devices are connected (or all network devices are
disabled in Windows
Network (connected)Indicates that one or more network drivers are installed, and
one or more network devices are connected to a wireless
network.
®
Control Panel).
Network (disconnected)Indicates that one or more network drivers are installed and
Network (disabled/disconnected)Indicates that one or more network drivers are installed, but
Using the wireless controls
You can control the wireless devices in your computer using these features:
Wireless button or wireless switch
●
Wireless Assistant software (select models only)
●
HP Connection Manager software (select models only)
●
Operating system controls
●
wireless connections are available, but no network devices
are connected to a wireless network.
no wireless connections are available (or all wireless network
devices are disabled by the wireless button or HP Wireless
Assistant).
18Chapter 3 Wireless and local area network
Using the wireless button
The computer has a wireless button, one or more wireless devices, and one or two wireless lights,
depending on the model. All of the wireless devices on your computer are enabled at the factory, so the
wireless light is on (blue) when you turn on the computer.
The wireless light indicates the overall power state of your wireless devices, not the status of individual
devices. If the wireless light is blue, at least one wireless device is on. If the wireless light is off, all
wireless devices are off.
NOTE:On some models, the wireless light is amber when all wireless devices are off.
Because the wireless devices are enabled at the factory, you can use the wireless button to turn on or
turn off the wireless devices simultaneously. Individual wireless devices can be controlled through
Wireless Assistant software (select models only).
Using Wireless Assistant software (select models only)
A wireless device can be turned on or off using the Wireless Assistant software. If a wireless device is
disabled in Setup Utility, it must be reenabled in Setup Utility before it can be turned on or off using
Wireless Assistant.
NOTE:Enabling or turning on a wireless device does not automatically connect the computer to a
network or a Bluetooth-enabled device.
To view the state of the wireless devices, click the Show hidden icons icon, the arrow at the left of the
notification area, and position the mouse pointer over the wireless icon.
If the wireless icon is not displayed in the notification area, complete the following steps to change
Wireless Assistant properties:
1.Select Start > Control Panel > Hardware and Sound > Windows Mobility Center.
2.Click the wireless icon in the Wireless Assistant tile, which is located in the bottom row of
Windows
3.Click Properties.
4.Select the check box next to HP Wireless Assistant icon in notification area.
5.Click Apply.
6.Click Close.
For more information, refer to the Wireless Assistant software Help:
1.Open Wireless Assistant by clicking the wireless icon in Windows Mobility Center.
2.Click the Help button.
®
Mobility Center.
Using wireless devices19
Using HP Connection Manager (select models only)
You can use HP Connection Manager to connect to WWANs using the HP Mobile Broadband device in
your computer (select models only).
To start HP Connection Manager, click the HP Connection Manager icon in the notification area, at
the far right of the taskbar.
For more details about using HP Connection Manager, refer to the HP Connection Manager software
Help.
Using operating system controls
Some operating systems also offer a way to manage integrated wireless devices and the wireless
connection. For example, Windows provides the Network and Sharing Center that allows you to set up
a connection or network, connect to a network, manage wireless networks, and diagnose and repair
network problems.
To access the Network and Sharing Center, select Start > Control Panel > Network and Internet >Network and Sharing Center.
For more information, select Start>Help and Support.
20Chapter 3 Wireless and local area network
Loading...
+ 83 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.