HP Omni 27-1010t, Omni 27-1015t, Omni 27-1054, Omni 27-1055, Omni 27-1057c, Omni 27-1058, Omni 27-1210xt User Manual
The only warranties for Hewlett-Packard
products and services are set forth in the
express statements accompanying such
products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable
for technical or editorial errors or omissions
contained herein.
HP assumes no responsibility for the use or
reliability of its software on equipment that is
not furnished by HP.
This document contains proprietary
information that is protected by copyright.
No part of this document may be
photocopied, reproduced, or translated to
another language without the prior written
consent of HP.
This product incorporates copyright
protection technology that is protected by
U.S. patents and other intellectual property
rights. Use of this copyright protection must
be authorized by Macrovision, and is
intended for home and other limited viewing
uses only unless otherwise authorized by
Macrovision. Reverse engineering or
disassembly is prohibited.
Microsoft, the Windows logo, and Windows
are trademarks or registered trademarks of
the Microsoft group of companies in the
United States and/or other countries/
regions.
HP supports lawful use of technology and
does not endorse or encourage the use of
our products for purposes other than those
permitted by copyright law. The information
in this document is subject to change without
notice.
Part number: 671405–001
Version 1.0
Table of contents
1 Preparing the computer for wall-mounting ....................................................................... 1
What you need ....................................................................................................................... 1
Safety information .................................................................................................................... 1
Preparing to remove the computer stand ..................................................................................... 2
Removing the computer stand .................................................................................................... 2
2 Reinstalling the stand on the computer ............................................................................. 9
What you need ....................................................................................................................... 9
Safety information .................................................................................................................... 9
Removing the wall-mounting hardware ...................................................................................... 10
Replacing the computer stand .................................................................................................. 11
iii
iv
1Preparing the computer for wall-
mounting
This document provides instructions for preparing your HP All-in-One computer for wall-mounting. The
VESA mounting bracket is attached to the back of the computer. This bracket attaches to a wallmounting device (sold separately). You need to remove the computer stand before wall-mounting the
computer.
To convert the computer from a wall-mounted unit to desktop unit, follow the instructions in the
Reinstalling the stand on the computer on page 9. It is very important that you follow all the steps to
reinstall the computer stand.
What you need
Wall-mounting device (sold separately) with the following specifications:
●
VESA standard 100 mm x 100 mm (3.9 in. x 3.9 in.) hole pattern
◦
Designed for flat-panel displays ranging in size from 508 mm to 687 mm (20 in. to 27 in.)
◦
diagonal, and weighing up to 22.7 kg (50 lb)
A stable, flat surface to place the computer
●
A soft, clean cloth (such as a clean, large towel) to protect the computer when you place it face
●
down
Antistatic wrist strap and a conductive foam pad to stand on while working on the computer
●
(recommended)
A Phillips #2 screwdriver (magnetic-tipped screwdriver recommended)
●
Another person (the computer is heavy and might require two people to lift and move it)
●
Safety information
This product has not been evaluated for connection to an “IT” power system (an AC distribution system
with no direct connection to the earth, according to IEC 60950).
WARNING!Always disconnect the computer from the power source before removing the computer
stand. Failure to do so before you perform any procedures can result in personal injury or equipment
damage.
WARNING!Avoid touching sharp edges inside the computer.
WARNING!It is recommended that you use only UL-listed wall-mounting devices.
WARNING!The computer is heavy. Take proper precautions when lifting or moving the computer.
What you need
1
WARNING!Please read “Additional Safety Information” in the Limited Warranty and Support
Guide before installing and connecting your system to the electrical power system.
Preparing to remove the computer stand
To avoid injury and equipment damage when opening the computer, always complete the following
steps in order:
1.Remove any media and external devices (such as any CD, DVD, memory cards, USB devices, or
external hard disk drives) from the computer.
CAUTION:Static electricity can damage the electronic components of the computer or optional
equipment.
2.Ensure that you are discharged of static electricity by briefly touching a grounded metal object.
3.Click the Windows Start button and then select Shut Down.
WARNING!To reduce the risk of personal injury from electrical shock or hot surfaces,
disconnect the power cord from the wall outlet, and allow the internal system components to cool
before touching them.
4.After the system has completely shut down, disconnect the power adapter from the back of the
computer.
5.Disconnect all other attached cables from the back and side of the computer.
Removing the computer stand
To mount the all-in-one computer to the wall, you must remove the computer stand.
2Chapter 1 Preparing the computer for wall-mounting
Loading...
+ 13 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.