HP MSM323-R Quick Start Manual

The MSM323-R (MSC-3300R) is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED

802.11a/b/g product. The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi
Alliance. The MSM323-R is certified under the SpectraLink Voice Interoperability for
Enterprise Wireless (VIEW) Certification Program.

VIEW
Certified

MSM323-R Integrated Services Access Point Quickstart

This Quickstart introduces the MSM323-R (US J9342A, WW J9345A) Integrated Services Access Point (formerly the MSC-3300R MultiService Controller) and
shows you how to get started using it. After following the directions in this Quickstart, see the MSC-3000 Series Admin Guide available at:
www.procurve.com/customercare/support/manuals/index.htm.

Hardware overview

MSM323-R Integrated Services Access Point Quickstart 2 HP ProCurve Networking

Package contents

MSM323-R featuring a die-cast aluminum enclosure with three-point silicone gasket, two

2.4-GHz (5.5-dBi) 802.11b/g omnidirectional antennas, weatherproof quick-disconnect
RJ-45 Ethernet connector, wall-mount bracket, pole-mount bracket assembly, grounding lug.
The MSM323-R ships fully assembled and ready to operate.

Radios and antennas

The MSM323-R has two radios each with a single antenna. The antenna connectors are
weatherproof straight-polarity N-type female bulkhead antenna connectors.

Ethernet port

The MSM323-R has a single 10/100 Mbps Ethernet port with weatherproof RJ-45 connector.

Note: The MSM323-R is a ruggedized version of the MSM323 and shares the same

feature set. However, due to its weather-proof enclosure: the LAN port, the serial
port, the reset button, and the status lights are not available. The MSM323-R
provides access to the Internet port only and this port has been configured to
support PoE. When using the management tool, ignore references to the LAN port.
For details on resetting the MSM323-R to its factory defaults, see “Resetting to
factory defaults” in the MSC-3000 Series Admin Guide.

Installation

WARN ING : PROFESSIONAL INSTALLATION REQUIRED: Prior to installing or using this

device, consult with a professional installer trained in RF installation and
knowledgeable in local regulations including building and wiring codes,
safety, channel, power, indoor/outdoor restrictions, and license
requirements for the intended country. It is the responsibility of the end
user to ensure that installation and use comply with local safety and radio
regulations.

• Surge protection and grounding: When connecting an outdoor antenna to the unit make

sure that proper lightning surge protection and grounding precautions are taken
according to local electrical code. Failure to do so may result in personal injury, fire,
equipment damage, or a voided warranty. The HP ProCurve hardware warranty provides
no protection against damage caused by static discharge or a lightning strike.

• Cabling: You must use the appropriate cables, and where applicable, surge protection,

for your given region. For compliance with EN55022 Class-B emissions requirements
use shielded Ethernet cables.

• Country of use: Some versions of the unit require the installer to select the appropriate

country during the initial set up. Once the country has been set, the unit will
automatically limit the available channels, ensuring compliant operation in the selected
country. Incorrectly entering the country may result in illegal operation and may cause
harmful interference to other systems.

Safety

Take note of the following safety information during installation:

• If your network covers an area served by more than one power distribution system, be

sure all safety grounds are securely interconnected.

• Network cables may occasionally be subject to hazardous transient voltages (caused by

lightning or disturbances in the electrical power grid).

• Handle exposed metal components of the network with caution.

• This product does not have a power switch. It is powered-on when it is connected to a

PoE power source.

Protection equipment needed

In addition to the items supplied with the MSM323-R, protection equipment will be required
according to your electrical code. For example:

• Antenna surge suppressor: HP ProCurve Antenna Lightning Arrester, part number

J8996A.

• Ethernet surge suppressor: Weatherproof PoE compatible 10/100 base-T CAT5

Lightning Protector.

Installation guidelines

The MSM323-R is typically interconnected with other equipment as follows (only the
antennas and weatherproof RJ-45 connector are supplied with the MSM323-R):

Installation procedure

WARNING: This is a general procedure. It is the installer’s responsibility to perform

all installation according to local electrical code and regulations.

WARNING: Corrosive damage caused by salt fog is not covered by the warranty.