The information contained herein is subject to
change without notice.
The only warranties for HP products and
services are set forth in the express warranty
statements accompanying such products and
services. Nothing herein should be construed
as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or
omissions contained herein.
Microsoft® and Windows® are U.S. registered
trademarks of Microsoft Corporation.
Welcome to your printer ........................................................................................................................................ 2
Supplementary parts ............................................................................................................................................. 2
The printer’s main components ............................................................................................................................ 7
The front panel ...................................................................................................................................................... 9
The Embedded Web Server ................................................................................................................................. 17
Connectivity and software instructions .............................................................................................................. 24
Turn the printer on and off .................................................................................................................................. 32
Restart the printer ............................................................................................................................................... 33
When you need help ............................................................................................................................................ 34
3 Handle the substrate and troubleshoot substrate issues ................................................................................ 36
Load a roll onto the spindle ................................................................................................................................. 42
Load a roll into the printer ................................................................................................................................... 46
The edge holders ................................................................................................................................................. 51
Load a cut sheet into the printer ......................................................................................................................... 53
How to cut substrate ........................................................................................................................................... 53
Unload a roll from the printer ............................................................................................................................. 54
The take-up reel (accessory) ............................................................................................................................... 55
View information about the substrate ................................................................................................................ 62
Change substrate width and right edge position ................................................................................................ 62
Store the substrate .............................................................................................................................................. 63
The substrate cannot be loaded successfully .................................................................................................... 63
The substrate is mispositioned ........................................................................................................................... 64
ENWWiii
The substrate has jammed .................................................................................................................................. 64
The substrate is deformed or wrinkled ............................................................................................................... 67
The substrate has shrunk or expanded .............................................................................................................. 67
The substrate has bow deformation ................................................................................................................... 68
Take-up reel substrate jam ................................................................................................................................. 68
Take-up reel does not wind ................................................................................................................................. 69
HP Media Locator ................................................................................................................................................. 73
Clone a substrate preset ..................................................................................................................................... 74
Modify a substrate preset ................................................................................................................................... 74
Add a new substrate ............................................................................................................................................ 75
Delete a substrate preset .................................................................................................................................... 79
Color calibration .................................................................................................................................................. 80
General printing advice ........................................................................................................................................ 84
6 The ink system ............................................................................................................................................ 97
Ink system tips .................................................................................................................................................. 101
Maintain the ink cartridges ................................................................................................................................ 101
Replace an ink cartridge .................................................................................................................................... 101
Cannot insert an ink cartridge ........................................................................................................................... 105
Clean (recover) the printheads .......................................................................................................................... 105
Align the printheads .......................................................................................................................................... 106
Front panel recommends reseating or replacing a printhead .......................................................................... 108
Replace a printhead ........................................................................................................................................... 108
Cannot insert a printhead .................................................................................................................................. 114
Clean the electrical connections on a printhead ............................................................................................... 115
Replace the maintenance cartridge .................................................................................................................. 119
ivENWW
Cannot insert the maintenance cartridge ......................................................................................................... 122
Clean and lubricate the carriage rod ................................................................................................................. 122
Clean the encoder strip ..................................................................................................................................... 124
Clean the platen ................................................................................................................................................. 125
Clean the exterior of the printer ....................................................................................................................... 127
Move or store the printer .................................................................................................................................. 127
Service maintenance ......................................................................................................................................... 128
Order ink supplies .............................................................................................................................................. 131
Order accessories .............................................................................................................................................. 132
10 Troubleshoot other issues ........................................................................................................................ 133
The printer cannot get an IP address ................................................................................................................ 134
Cannot access the Embedded Web Server ........................................................................................................ 134
The printer is not printing ................................................................................................................................. 134
The software program slows down or stalls while generating the print job ................................................... 135
The printer seems slow ..................................................................................................................................... 135
Communication failures between computer and printer ................................................................................. 135
Cannot connect to services such as firmware update, online search, or the Customer Involvement
Program ............................................................................................................................................................. 136
Power specifications ......................................................................................................................................... 144
Index ........................................................................................................................................................... 152
ENWWv
viENWW
1Introduction
●
Welcome to your printer
●
Supplementary parts
●
Documentation
●
Safety precautions
●
The printer’s main components
●
The front panel
●
The Embedded Web Server
●
Connectivity and software instructions
●
Advanced network configuration
●
Turn the printer on and off
●
Restart the printer
ENWW1
Welcome to your printer
Your printer is a color inkjet printer designed for printing high-quality images on flexible substrates. Some
major features of the printer are shown below:
●
Environmentally friendly, odorless, aqueous latex inks in six colors plus optimizer
●
No special ventilation required, no hazardous waste
●
400 ml ink cartridges
●
Sharpest print quality, smooth transitions, and fine details with 1200 real dpi
●
Consistent and repeatable print quality at every print speed
●
Prints are completely dry and ready for finishing and delivery
●
Print on a wide range of substrates—including most low-cost, uncoated, solvent-compatible substrates
●
A range of HP recyclable substrates is available
●
Consider un-laminated use with scratch resistance comparable to hard solvent inks on SAV and PVC
banners
●
Durable prints with outdoor display permanence up to three years unlaminated, five years laminated
●
Hundreds of ready-made substrate presets easily available
To send print jobs to your printer, you will need Raster Image Processor (RIP) software, which should be run
on a separate computer. RIP software is available from various different companies.
Supplementary parts
Supplied with the printerHP Latex 3x0 Edge Holders
Optional accessoriesHP Latex 3x0 Edge Holders
ConsumablesHP 831 Latex Printheads (1 set included in box)
HP Latex 54-in Printer 2-in Spindle (including 2- to 3-in spindle adaptor)
HP Latex 3x0 User Maintenance Kit
FlexiPRINT HP Basic 100 Series Edition
HP Latex 54-in Take-Up Reel (including 2-in spindle with 3-in adaptor)
HP Latex 54-in Printer 2-in Spindle (including 2- to 3-in spindle adaptor)
HP Latex 3x0 User Maintenance Kit
HP 821 Latex Ink Cartridges
HP 831 Latex Maintenance Cartridge (1 included in box)
Documentation
The following documents can be downloaded from http://www.hp.com/go/latex110/manuals/:
●
Introductory information
●
User's guide
2Chapter 1 IntroductionENWW
●
Legal information
●
Limited warranty
The Quick Response (QR) code images found in some parts of this user´s guide provide links to additional
video explanations of particular topics. For an example of such an image, see The printer’s main components
on page 7.
Safety precautions
Before using your printer, read the following safety precautions to make sure you use the equipment safely.
You are expected to have the appropriate technical training and experience necessary to be aware of hazards
to which you may be exposed in performing a task, and take appropriate measures to minimize the risks to
yourself and to other people.
General safety guidelines
●
There are no operator-serviceable parts inside the printer except those covered by HP's Customer Self
Repair program (see http://www.hp.com/go/selfrepair/). Refer servicing of other parts to qualified
service personnel.
●
Turn off the printer and call your service representative in any of the following cases:
◦
The power cord or plug is damaged.
◦
The curing enclosures are damaged.
◦
The printer has been damaged by an impact.
◦
There is any mechanical or enclosure damage.
◦
Liquid has entered the printer.
◦
There is smoke or an unusual smell coming from the printer.
◦
The printer has been dropped or the curing module has been damaged.
◦
The printer is not operating normally.
●
Turn off the printer in either of the following cases:
◦
During a thunderstorm
◦
During a power failure
●
Take special care with zones marked with warning labels.
Electrical shock hazard
WARNING!The internal circuits of curing zones, output drier, print-zone heaters, and built-in power
supplies operate at hazardous voltages capable of causing death or serious personal injury.
The printer uses two power cords. Unplug both power cords before servicing the printer.
To avoid the risk of electric shock:
●
The printer must be connected to earthed mains outlets only.
●
Do not attempt to dismantle the curing modules.
ENWWSafety precautions3
●
●
Heat hazard
The curing subsystems of the printer operate at high temperatures and can cause burns if touched. To avoid
personal injury, take the following precautions.
●
●
●
Fire hazard
The curing subsystems of the printer operate at high temperatures.
To avoid the risk of fire, take the following precautions.
●
Do not remove or open any other closed system covers or plugs.
Do not insert objects through slots in the printer.
Do not touch the internal enclosures of the printer's curing zones.
Let the printer cool down when accessing the internal curing zone and output platen in case of a
substrate jam.
Let the printer cool down before performing some maintenance operations.
The customer is responsible for meeting the printer's requirements and the Electrical Code
requirements according to the local jurisdiction of the country where the equipment is installed. Use the
power supply voltage specified on the nameplate.
●
Connect the power cords to dedicated lines, each protected by a branch circuit breaker according to the
information detailed in the site preparation guide. Do not use a power strip (relocatable power tap) to
connect both power cords.
●
Use only the power cords supplied by HP with the printer. Do not use a damaged power cord. Do not use
the power cords with other products.
●
Do not insert objects through slots in the printer.
●
Take care not to spill liquid on the printer. After cleaning, make sure all components are dry before
using the printer again.
●
Do not use aerosol products that contain flammable gases inside or around the printer. Do not operate
the printer in an explosive atmosphere.
●
Do not block or cover the openings of the printer.
●
Do not attempt to dismantle or modify the curing modules.
●
Ensure that the operating temperature of the substrate recommended by the manufacturer is not
exceeded. If this information is not available, ask the manufacturer. Do not load substrates that cannot
be used at an operating temperature above 125°C (257°F).
●
Do not load substrates with auto-ignition temperatures below 250°C (482°F). If this information is not
available, printing must be supervised at all times. See note below.
NOTE:Test method based on EN ISO 6942:2002; Evaluation of materials and material assemblies when
exposed to a source of radiant heat, method B. The test conditions, to determine the temperature when the
substrate starts ignition (either flame or glow), were: Heat flux density 30 kW/m², copper calorimeter, K type
thermocouple.
Mechanical hazard
The printer has moving parts that could cause injury. To avoid personal injury, take the following precautions
when working close to the printer.
4Chapter 1 IntroductionENWW
●
Keep your clothing and all parts of your body away from the printer's moving parts.
●
Avoid wearing necklaces, bracelets, and other hanging objects.
●
If your hair is long, try to secure it so that it will not fall into the printer.
●
Take care that sleeves or gloves do not get caught in the printer's moving parts.
●
Avoid standing close to the fans, which could cause injury and could also affect print quality (by
obstructing the air flow).
●
Do not touch gears or moving rolls during printing.
●
Do not operate the printer with covers bypassed.
Light radiation hazard
Light radiation is emitted from the illumination of the print zone. This illumination is in compliance with the
requirements of the exempt group of IEC 62471:2006, Photobiological safety of lamps and lamp systems.
However, you are recommended not to look directly at the LEDs while they are on. Do not modify the module.
Heavy substrate hazard
Special care must be taken to avoid personal injury when handling heavy substrates.
●
Handling heavy substrate rolls may require more than one person. Care must be taken to avoid back
strain and/or injury.
●
Consider using a forklift, pallet truck, or other handling equipment.
●
When handling heavy substrate rolls, wear personal protective equipment including boots and gloves.
Ink handling
HP recommends that you wear gloves when handling ink system components.
Warnings and cautions
The following symbols are used in this manual to ensure the proper use of the printer and to prevent the
printer from being damaged. Follow the instructions marked with these symbols.
WARNING!Failure to follow the guidelines marked with this symbol could result in serious personal injury
or death.
CAUTION:Failure to follow the guidelines marked with this symbol could result in minor personal injury or
damage to the printer.
Warning labels
Label
Explanation
Printer label. To identify the printer’s power cord.
ENWWSafety precautions5
LabelExplanation
Curing label. To identify the curing power cord.
Electric shock hazard. Heating modules operate at hazardous
voltages. Disconnect power source before servicing.
CAUTION: Double pole. Neutral fusing.
Equipment to be connected to earthed mains outlet only. Refer
servicing to qualified service personnel. Disconnect all power
cords before servicing. No operator serviceable parts inside the
printer.
Before starting, read and follow the operating and safety
instructions. Ensure that the input voltage is within the printer's
rated voltage range. The printer requires up to two dedicated
lines.
This label is located on the e-box.
Risk of burns. Do not touch the curing zone or the output platen
of the printer: they could be hot.
This label is located on the front of the curing module.
Risk of trapped fingers. Do not touch moving gears.
These labels are located at the rear of the printer, on the
substrate input gear.
Moving part. Keep away from the moving printhead carriage.
When printing, the printhead carriage travels back and forth
across the substrate.
This label is located on the rear of the scan axis window, behind
the plastic.
You are recommended to wear gloves when handling the
maintenance cartridge or the platen.
This label is located on the maintenance cartridge.
Electric shock hazard. Heating modules operate at hazardous
voltages. Disconnect all power sources before servicing.
This label is located on the curing control PCA enclosure. For
service personnel only.
6Chapter 1 IntroductionENWW
NOTE:The final label position and its size on the printer may vary slightly, but should always be visible and
close to the potential risk area.
The printer’s main components
The above image is a QR code containing a link to a video; see Documentation on page 2.
The following views of the printer illustrate its main components.
Front view
1.Ink cartridge
2.Platen
3.Printhead
4.Printhead carriage
5.Front panel
6.Maintenance cartridge
7.Substrate pinch lever
8.Spindle lock lever
9.Spindle
ENWWThe printer’s main components7
10. Spindle stop with 2-in to 3-in adaptor
11. Loading table
12. Curing module
Rear view
1.Power switch and power socket
2.Sockets for communication cables and optional accessories
Take-up reel motor (accessory)
8Chapter 1 IntroductionENWW
1.Winding-direction switch
2.Manual winding buttons
3.Take-up reel lever
The front panel
Introduction to the front panel
The front panel is a touch-sensitive screen with a graphical user interface; it is located on the front right of
the printer. It gives you complete control of your printer: from the front panel, you can view information
about the printer, change printer settings, perform calibrations and tests, and so on. The front panel also
displays alerts (warning and error messages) when necessary.
There is an alternative home screen that you can see by sliding your finger across the screen to the left.
The front panel has a large central area to display dynamic information and icons. On the left and right sides
you can see up to four fixed icons at different times. Normally they are not all displayed at the same time.
Left and right fixed icons
●
Press to return to the home screen.
●
Press to view help about the current screen.
●
Press to go back to the last-visited screen. This does not discard any changes made in the current
screen.
●
Press to cancel the current process.
ENWWThe front panel9
Home screen dynamic icons
The following items are displayed only on the home screen.
●
At the top left of the screen is a message showing the printer status or the most important current
alert. Press this message to see a list of all current alerts, with an icon indicating the severity of each
alert. You can press an alert to get help in solving the problem.
●
At the top right, press to turn on or off the print-zone illumination light.
●
Press to view substrate status and perform substrate-handling operations.
●
Press to open the Substrate Library and access the extensive online library of substrate presets.
●
Press to view information about the job that is currently printing.
●
Press to view ink-cartridge status and perform operations.
●
Press to view printhead status and perform operations.
●
Press to view and change printer settings in general.
●
Press to view network and Internet status and change related settings.
●
Press to view information about the printer.
●
Press for help.
If the printer is left idle for some time, it goes into sleep mode and switches off the front-panel display. To
change the time that elapses before sleep mode, press , then Setup > Front panel options > Sleep
mode wait time. You can set a time between 5 and 240 minutes; the default is 25 minutes.
The printer wakes from sleep mode and switches on the front-panel display whenever there is some external
interaction with it.
Information about specific uses of the front panel can be found throughout this guide.
Change the language of the front panel
Two methods are available to change the language that is used for the front-panel menus and messages.
10Chapter 1 IntroductionENWW
●
If you can understand the current front panel language, go to the front panel and press , then
Setup > Front panel options > Language.
●
If you cannot understand the current front panel language, start with the printer turned off. Turn it on.
As soon as the icon appears, press it for a few seconds. When all icons have appeared on the front
panel, press followed by . The front panel blinks briefly.
Whichever method you used, the language selection menu should now appear on the front panel.
Press the name of your preferred language.
View or set the date and time
To view or set the printer's date and time, go to the front panel and press , then Setup > Front panel
options > Date and time options.
Set altitude
If your printer is operating at more than 500 m (1640 ft) above sea level, go to the front panel and press
, then Setup > Select altitude, to tell the printer its operating altitude.
Set time before standby
When there are no more jobs to print, or you want to pre-warm the printer (Prepare printing option in the
RIP), the printer´s curing heaters remain on for the specified time and temperature in case another job
arrives or in case you need to avoid any print-quality problem that could be caused by an incorrect
temperature in the print zone. To choose how long the heaters will stay on in this situation, go to the front
panel and press then Substrate > Substrate handling options > Curing standby duration. You can
select from 5 to 120 minutes.
The curing temperature during this standby period is set automatically by the printer.
Change the sleep mode setting
If the printer is left turned on but unused for a certain period of time, it automatically goes into sleep mode to
save power. The default period of time it waits is 25 minutes. To change the time the printer waits before it
goes into sleep mode, go to the front panel and press , then Setup > Front panel options > Sleep mode
wait time
ENWWThe front panel11
. Enter in minutes the wait time that you want, then press OK.
Change the loudspeaker volume
To change the volume of the printer's loudspeaker, go to the front panel and press , then Setup > Front
panel options
> Speaker volume, and select Off, Low, or High.
Turn audio alerts on or off
To turn the printer's audio alerts on or off, go to the front panel and press , then Setup > Front panel
options > Enable audio alert or Disable audio alert. By default, audio alerts are enabled.
Change the front panel display brightness
To change the brightness of the front-panel display, press , then Setup > Front panel options > Display
brightness
, then select a value by moving the scroll bar. Press OK to save the value.
Change the units of measurement
To change the units of measurement that appear on the front panel, press , then Setup > Front panel
options > Unit selection, then English or Metric.
The units of measurement can also be changed in the Embedded Web Server. See Access the Embedded Web
Server on page 19.
Restore factory settings
To restore the printer settings to their original values as set in the factory, go to the front panel and press
, then Setup > Resets > Restore factory settings. This option restores all of the printer settings except
the Gigabit Ethernet settings and substrate presets.
Check printer status
The front panel and the Embedded Web Server both display the status of the printer, the loaded substrate,
and the ink system.
Check the status of the ink cartridges
You can see the ink levels in your ink cartridges by pressing on the front panel's home screen.
For more details about any particular ink cartridge, press the rectangle representing that cartridge. The
following information is shown.
12Chapter 1 IntroductionENWW
●
Status
●
Estimated ink level
●
Warranty status
●
Manufacturer
●
Capacity
●
Product name
●
Product number
●
Serial number
●
Expiration date
●
Supported ink cartridges
These are the possible ink cartridge status messages that you can see on the front panel:
●
OK: The cartridge is working normally, with no known problems.
●
Missing: There is no cartridge present, or it is not correctly connected to the printer.
●
Low: The ink level is low.
●
Very low: The ink level is very low.
●
Empty: The cartridge is empty.
●
Reseat: You are recommended to remove the cartridge and then reinsert it.
●
Replace: You are recommended to replace the cartridge with a new cartridge.
●
Expired: The cartridge’s expiration date has passed.
●
Incorrect: The cartridge is not compatible with this printer. The message includes a list of compatible
cartridges.
●
Non-HP: The cartridge is used, refilled, or counterfeit.
You can also view the status of the ink cartridges in the Embedded Web Server. See Access the Embedded
Web Server on page 19.
Check the status of a printhead
The printer automatically checks and services the printheads after each print. Follow these steps to get more
information on your printheads.
1.
On the front panel's home screen, press .
ENWWThe front panel13
2.Select the printhead for which you want to see information.
3.The front panel shows the following information.
●
Status
●
Warranty status
●
Product name
●
Product number
●
Serial number
●
Ink fired
●
Install date
These are the possible printhead status messages that you can see on the front panel:
●
OK: The printhead is working normally, with no known problems.
●
Missing: There is no printhead present, or it is not correctly installed in the printer.
●
Reseat: You are recommended to remove the printhead and then reinsert it. If that fails, clean the
electrical connections (see Clean the electrical connections on a printhead on page 115). If that fails,
replace the printhead with a new printhead (see Replace a printhead on page 108).
●
Replace: The printhead is failing. Replace the printhead with a working printhead (see Replace a
printhead on page 108).
●
Replacement incomplete: The printhead replacement process has not completed successfully; restart
the replacement process and let it finish completely.
●
Remove: The printhead is not a suitable type for use with your printer.
●
Non-HP ink: Ink from a used, refilled, or counterfeit ink cartridge has passed through the printhead. See
the limited warranty document provided with your printer for details of the warranty implications.
14Chapter 1 IntroductionENWW
You can also use the Embedded Web Server to check the printhead status and the warranty status. See
Access the Embedded Web Server on page 19.
Check the file system
It is possible to check the integrity of the file system on the printer's hard disk, and automatically correct any
errors. You are recommended to do this about once every six months, or if you notice any trouble in
accessing files on the hard disk.
To execute the file system check, go to the front panel and press , then Preventive maint. tasks > File
system check.
If the printer is aware of damage to the file system, for instance after a severe software problem, it may start
a file system check automatically. This can take about ten minutes.
Printer alerts
The printer can communicate two types of alerts:
●
Errors: When the printer is unable to print.
●
Warnings: When the printer needs attention for an adjustment, such as a calibration, preventive
maintenance, or ink cartridge replacement.
●
Advice: When a firmware update is available or the downloaded firmware is ready to be installed.
Printer alerts appear in the front panel and in the Embedded Web Server.
●
Front-panel display: The front panel shows the alerts in the upper left part of the screen (notification
bar).
Only one alert is shown at a time. If you press the notification bar, all the current printer alerts are
shown. The list of alerts can be folded back by pressing or sliding up the bottom row of the list.
Clicking an alert opens the application that could help to resolve it. Firmware update advice is dismissed
when entering the Printer application. Once dismissed, there won’t be any reminder later on about the
ENWWThe front panel15
same advice (in the case of firmware updates, a new notification appears when there a new firmware
release becomes available).
●
Embedded Web Server: The Embedded Web Server shows only one alert at a time, which is judged to be
the most important.
An alert may require you to perform a maintenance operation; see Hardware maintenance on page 100.
The following alerts require a service engineer:
●
Service Maintenance Kit 1
●
Service Maintenance Kit 2
●
Service Maintenance Kit 3
Printer states
The printer may be in any one of the following states; some of them require waiting.
●
Ready (cold): The printer is powered on but has not printed yet, and the heaters are not turned on.
●
Preparing to print: The printer is warming up the heaters and preparing the printheads to print. This
takes 1 to 6 min.
●
Ready for substrate
●
Ready for side A/B
●
Printing
●
Printing side A/B
●
Drying: This takes 1.5 to 5 min.
●
Finishing: The printer is cooling down and preparing for stand-by. This takes 0.5 to 5 min.
If jobs of the same print mode as the already-printed file are sent while the printer is Drying or Finishing, the
printer goes to Preparing to print.
To save time between prints, you are recommended to use nesting to print several jobs in the same
workflow.
Change margins
The printer margins determine the area between the edges of your image and the edges of the substrate.
The side margins for a particular print job are selected in the RIP software; if the job exceeds the substrate
width, it will be clipped.
The front panel offers additional settings for the top and bottom margins: see Table 11-4 Margins
on page 144. These settings apply only to single prints.
To set the top margin at the front panel, press , then Substrate > Substrate handling options > Extra
top margin
To set the bottom margin at the front panel, press , then Substrate > Substrate handling options >
Extra bottom margin.
NOTE:The extra top/bottom margin set in the front panel is applied in addition to the top/bottom margin
selected in the RIP.
16Chapter 1 IntroductionENWW
.
NOTE:The side margins can be adjusted in the RIP.
Request the printer’s internal prints
The internal prints provide various kinds of information about your printer. Request these prints from the
front panel, without using a computer.
Before requesting any internal print, make sure that substrate is loaded and that the Ready message
appears on the front-panel display.
To print an internal print, press , then Setup > Internal prints, then select the type of internal print that
you want.
The following internal prints are available:
●
Usage report: Shows estimates of the total number of prints, number of prints by substrate family,
number of prints by print-quality option, and total amount of ink used per color. The accuracy of these
estimates is not guaranteed.
●
Service information: Provides information that service engineers require.
Check lifetime usage statistics
There are two ways of checking your printer's usage statistics.
NOTE:The accuracy of the usage statistics is not guaranteed.
●
From the Embedded Web Server, go to the Main tab and select History > Usage. See The Embedded
Web Server on page 17.
●
From the front panel, press , then Setup > Internal prints > User information prints > Print
usage report.
The Embedded Web Server
Introduction to the Embedded Web Server
The Embedded Web Server is a Web server running inside the printer. You can use it to obtain printer
information, manage settings and presets, align printheads, upload new firmware and troubleshoot
problems. Service engineers can use it to retrieve internal information that helps to diagnose printer
problems.
You can access the Embedded Web Server remotely by using an ordinary Web browser running on any
computer. See Access the Embedded Web Server on page 19.
The Embedded Web Server window displays three separate tabs. Buttons near the top of each page provide
access to online help and supplies reordering.
ENWWThe Embedded Web Server17
Main tab
The Main tab provides information about the following items.
●
●
●
Setup tab
The Setup tab enables you to complete these tasks.
●
●
●
●
●
●
●
Substrate, ink, printhead and maintenance status
Temperature of the curing module
Substrate and ink usage and accounting
Specify printer settings such as units of measurement and refresh date
Specify network and security settings
Set the date and time
Update firmware
Align printheads
Upload substrate presets
Configure e-mail notifications
Support tab
The Support tab offers various kinds of help with your printer.
●
Browse helpful information from a variety of sources
●
Troubleshoot problems
●
Access HP links for technical support with your printer and accessories
●
Access service support pages that show current and historical data on the usage of your printer
Networking tab
The Networking tab enables you to change the printer’s networking configuration.
18Chapter 1 IntroductionENWW
Customer Involvement Program tab
The Customer Involvement Program tab enables you to sign up for the Customer Involvement Program and
configure your participation.
Access the Embedded Web Server
Use the Embedded Web Server to view printer information remotely through an ordinary Web browser
running on any computer.
The following browsers are known to be compatible with the Embedded Web Server:
●
Internet Explorer 7 and later for Windows
●
Safari 3 and later for Mac OS X
●
Mozilla Firefox 3.6 and later
●
Google Chrome 7 and later
To use the Embedded Web Server on any computer, open your Web browser and type the printer's IP address
in the browser's address bar. The printer's IP address appears on the printer’s front panel, after pressing
.
If you follow these instructions but fail to open the Embedded Web Server, see Cannot access the Embedded
Web Server on page 134.
Change the language of the Embedded Web Server
The Embedded Web Server functions in the following languages: English, Portuguese, Spanish, Catalan,
French, Italian, German, Simplified Chinese, Traditional Chinese, Korean, and Japanese. It uses the language
that you specified in your Web browser options. If you specify a language that it cannot support, it functions
in English.
To change the language, change your Web browser's language setting. For example, in Chrome, Settings,
Language (in the advanced settings view), make sure that the language you want is at the top of the list in
the dialog box; or, in Internet Explorer version 8, go to the Tools menu and select Internet Options >
Languages. Make sure that the language you want is at the top of the list in the dialog box.
To complete the change, close and reopen your Web browser.
Restrict access to the printer
From the Embedded Web Server, you can select Setup > Security to set an administrator password. Once set,
this password must be given in order to perform the following printer functions.
●
Clear accounting information.
●
Update the printer’s firmware.
●
Change security settings.
●
View protected printer information.
●
Change Internet connection settings.
●
Change some networking settings.
●
Configure the Customer Involvement Program.
●
Run connectivity troubleshooting tests.
ENWWThe Embedded Web Server19
For more information, see the Embedded Web Server's online help.
If you forget the administrator password, you can delete the current password from the front panel: press
, then Setup > Connectivity > Advanced > Embedded Web Server > Reset EWS password.
Join the Customer Involvement Program
You can activate or deactivate the Customer Involvement Program from the Embedded Web Server or from
the printer's front panel.
NOTE:From the front panel, press , then Setup > Customer Involvement Program.
The Customer Involvement Program is a statistical printer-usage tracking system. It may also be used to
determine eligibility for certain usage-based reward programs, or to monitor the device in connection with
optional services such as proactive cartridge replacement, pay-per-use contracts, or support agreements
(availability varies by product, region, and country). See the Customer Involvement Program tab of the
Embedded Web Server for details on the data collected and HP’s use of the data. Once the Customer
Involvement Program is enabled, your printer will automatically send 'usage snapshots' to HP through the
Internet approximately once a week, for as long as the Customer Involvement Program remains enabled. The
snapshot files are collected on a repository server, then automatically processed to extract the relevant
data, which are stored in a usage database. Sending the data does not interfere with the normal operation of
your printer, and does not require attention of any kind. You can stop participating at any time, in which case
data transmissions stop immediately.
The CIP configuration page of the Customer Involvement Program tab is where you can start, stop, or
change your participation in the Customer Involvement Program. By default, only anonymous usage data are
sent to HP, but you have the option to include the printer’s serial number. This may be necessary for certain
programs or services, and may allow us to provide you with better product service and support. Once you
have made any changes to the settings, click the Apply button to apply them.
If the Customer Involvement Program was enabled before clicking the Apply button, a connectivity test is
automatically made to determine whether Customer Involvement Program data can be successfully
delivered to HP.
20Chapter 1 IntroductionENWW
If the test completes successfully, configuration is complete and you can proceed to any other Embedded
Web Server page, or close the browser window. If the test fails, follow the instructions to try to identify and
fix the problem.
The CIP status and test page of the Customer Involvement Program tab can be used to check the current
status (enabled or not, anonymous data or not), and to run a connectivity test to check that Customer
Involvement Program data can be successfully delivered to HP.
Check printer status
The front panel and the Embedded Web Server both display the status of the printer, the loaded substrate,
and the ink system.
Check the status of the ink system
1.Access the Embedded Web Server (see Access the Embedded Web Server on page 19).
2.Go to the Supplies page on the Main tab.
The Supplies page shows you the status of the loaded substrate, the ink cartridges, the printheads, the
heater, and the maintenance cartridge.
The traffic light shows whether maintenance is required.
For further information, click Click to view details.
ENWWThe Embedded Web Server21
Request email notification of specific error conditions
1.In the Embedded Web Server (see Access the Embedded Web Server on page 19), go to the Email Server
page on the Setup tab and ensure that the following fields are correctly filled in:
●
SMTP server. This is the IP address of the outgoing mail server (Simple Mail Transfer Protocol
[SMTP]) that processes all email messages from the printer. If the mail server requires
authentication, email notifications will not work.
●
Printer email address. Each email message that the printer sends must include a return address.
This address does not need to be a real, functional email address, but it should be unique, so that
recipients of the message can identify the printer that sent it
2.Go to the Notification page, which is also on the Setup tab.
3.Click the New icon to request new notifications, or click the Edit icon to edit notifications that have
already been set up. Then specify the email addresses to which notifications are sent, and select the
incidents that result in notification messages.
Get accounting information
There are various different ways of getting accounting information from your printer.
●
View printer usage statistics for a particular job, see Check usage statistics for a job on page 22.
●
View printer usage statistics for the whole lifetime of the printer, see Check lifetime usage statistics
on page 22.
●
Request accounting data by email. The printer sends data in XML at regular intervals to a specified email
address; the data may be interpreted and summarized by a third-party application, or displayed as an
Excel spreadsheet. See Request accounting data by email on page 23.
●
Use a third-party application to request printer status, printer usage or job accounting data from the
printer through the Internet. The printer provides data in XML to the application whenever requested.
HP provides a Software Development Kit to facilitate the development of such applications.
By default, user names are not included in accounting information. If you would like to include them, check
the box Show user name in job accounting in the Security menu.
Check usage statistics for a job
You can use the Embedded Web Server to check usage statistics for a particular job: go to the Main tab and
select History > Accounting.
NOTE:The accuracy of the usage statistics is not guaranteed.
Check lifetime usage statistics
There are two ways of checking your printer's usage statistics.
NOTE:The accuracy of the usage statistics is not guaranteed.
●
From the Embedded Web Server, go to the Main tab and select History > Usage.
●
From the front panel, press , then Setup > Internal prints > User information prints > Print
usage report
22Chapter 1 IntroductionENWW
.
Request accounting data by email
1.Obtain the IP address of the outgoing mail server (SMTP) from your IT department; this is required in
order to send email messages.
2.Ensure that the outgoing email server is configured to enable relaying of email messages that the
printer will send.
3.Open your Web browser and connect to the printer’s Embedded Web Server.
4.Select the Setup tab.
5.From the Configuration menu in the left-hand column, select Date & Time.
6.Ensure that the printer's date and time have been set correctly.
7.From the Configuration menu, select Email server.
8.Enter the IP address of the outgoing mail server (SMTP).
9.Specify an email address for the printer. The latter does not need to be a valid email address, because
the printer will not receive messages; but it should have the form of an email address. It serves to
identify the printer when it sends email messages.
10. From the Configuration menu, select Printer settings.
11. Set Send accounting files to Enabled.
12. Set Send accounting files to to the email address (or addresses) to which you want the accounting
information sent. This may be an address that you have created specifically to receive automatically
generated messages from the printer.
13. Set Send accounting files every to the frequency with which you want the information sent, choosing a
specific number of days or prints.
14. You may want to set Exclude personal information from accounting email to On, so that the
accounting messages will not contain personal information. If this option is Off, information such as
user name, job name, and account ID will be included.
When you have completed the above steps, the printer will send accounting data by email with the frequency
that you specified. The data are provided in XML and can easily be interpreted by a third-party program. The
data provided on each print job include when the job was submitted, when the job was printed, the printing
time, the type of image, the number of pages, the number of copies, the paper type and size, the amount of
each color of ink used and various other attributes of the job. Accounting data are also provided on scan and
copy jobs.
You can download an Excel template from HP's Web site (http://www.hp.com/go/designjet/accounting/) that
will enable you to display the XML data more readably in the form of a spreadsheet.
Analysis of the accounting data will enable you to bill customers precisely and flexibly for the use of your
printer. You can, for instance:
●
Bill each customer for the total amount of ink and paper used by that customer over a particular period.
●
Bill each customer separately per job.
●
Bill each customer separately for each project, broken down by job.
ENWWThe Embedded Web Server23
Connectivity and software instructions
Connection method
Your printer can be connected in the following way.
NOTE:The speed of any network connection depends on all the components that are used in the network,
which can include network interface cards, hubs, routers, switches, and cables. If any one of these
components cannot operate at high speed, you will have a low-speed connection. To get the expected
performance from your printer, you should use equipment that supports 1000TX Full Gigabit. The speed of
your network connection can also be affected by the total amount of traffic from other devices on the
network.
Connect the printer to your network
The printer is able to configure itself automatically for most networks, in a similar way to any computer in
the same network. The first time you connect it to a network, this process may take a few minutes. If
necessary, see Advanced network configuration on page 25.
Once the printer has a working network configuration, you can check its network address from the front
panel: press .
Network configuration
For more details about the current network configuration, go to the front panel and press , then
Long (100 m=328 ft)Requires extra equipment
(switches)
Using IPv6
Connectivity > Network connectivity > Gigabit Ethernet > Modify configuration. From here it is possible,
though not normally necessary, to change the settings manually; this can also be done remotely using the
Embedded Web Server.
TIP:You may find it helpful to print out the full printer network configuration on paper. This can be done
from the front panel: press , then Internal prints > Service information prints > Print connectivity
configuration
IP address and network name.
If you accidentally misconfigure the printer’s network settings, you can restore the network settings to their
factory values from the front panel: press , then Connectivity > Network connectivity > Advanced >
Restore factory settings. Then you must restart the printer. This automatically provides a working network
configuration for most networks. The printer’s other settings remain unchanged.
Your printer supports almost all network connectivity features using IPv6, just as it does using IPv4. To make
full use of IPv6, you may need to connect your printer to an IPv6 network in which there are IPv6 routers and
servers.
In most IPv6 networks, the printer will configure itself automatically as follows, and no user configuration is
necessary:
. If you do not print out the full network configuration, consider making a note of the printer's
24Chapter 1 IntroductionENWW
1.The printer assigns itself a link-local IPv6 address (which starts with “fe80::”).
2.The printer assigns itself stateless IPv6 addresses as indicated to it by any IPv6 routers on the network.
3.If no stateless IPv6 addresses can be assigned, the printer will try to obtain IPv6 addresses using
DHCPv6. It will also do so if the routers instruct it to do so.
The stateless and DHCPv6 IPv6 addresses can be used to access the printer, and in most IPv6 networks this
will be appropriate.
The link-local IPv6 address works only in the local subnet. Although it is possible to access the printer using
this address, it is not recommended.
It is possible to assign a manual IPv6 address to the printer, using the front panel or the Embedded Web
Server. It is also possible to disable IPv6 completely in the printer. However, it is not possible to disable IPv4
in the printer, and therefore it is not possible to configure the printer as IPv6-only.
NOTE:In typical IPv6 use, your printer will have multiple IPv6 addresses, although it has only one IPv4
address.
TIP:You are recommended to give a name to the printer. You can do this from the front panel or (more
easily) from the Embedded Web Server.
TIP:You will generally find it easier to use IPv4 unless you have a specific need to use IPv6.
Microsoft Windows Vista, Microsoft Windows Server 2008, later versions of Windows, and the new HP
Printing and Imaging devices have IPv6 enabled by default. For further information on IPv6, see
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00840100/c00840100.pdf. This document
discusses how name resolution plays a fundamental role in Dual-Stack transition methods. Using the name
resolution algorithm in Windows, the document goes through various network environments and studies
how the introduction of routable IPv6 addresses will affect network applications. It also discusses DHCPv6,
SLAAC and the impact to DNS, and makes some recommendations.
Connect the printer to the Internet
To connect to the Internet, go to the front panel and press , then Connectivity > Connectivity wizard.
The connectivity wizard also checks that the printer’s firmware is up to date. Normally you need to run the
wizard only once, when first setting up the printer.
An Internet connection is needed for various printer functions described in this guide, such as the Embedded
Web Server.
RIP software installation
Install the RIP software by following the instructions provided with the software.
Advanced network configuration
You will probably not need to read this section, but the information is provided as it may be useful in some
cases.
The printer provides a single RJ-45 connector port for a network connection. In order to meet Class B limits,
the use of shielded I/O cables is required.
The embedded Jetdirect print server supports connection to IEEE 802.3 10Base-T Ethernet, IEEE 802.3u
100Base-TX Fast Ethernet and 802.3ab 1000Base-T Gigabit Ethernet compliant networks. When connected
and powered on, the printer auto-negotiates with your network to operate with a link speed of 10, 100, or
1000 Mbps, and to communicate using full- or half-duplex mode. However, you can manually configure the
ENWWAdvanced network configuration25
link using the printer's front panel, or through other configuration tools once network communication is
established.
The printer can support multiple network protocols simultaneously, including TCP/IPv4 and TCP/IPv6. For
security, it includes features to control IP traffic to and from the printer.
Verify correct operation
1.Print an IO Configuration page to check for status messages.
2.In the upper section of the IO Configuration page, look for the status message I/O Card Ready.
3.If I/O Card Ready appears, the print server is operating properly. Proceed to the next section.
If a message other than I/O Card Ready appears, try the following:
a.Turn the printer off and then on again to re-initialize the print server.
b.Check that the status indicator lights (LEDs) are providing proper status.
NOTE:See Troubleshooting on page 26 for link configuration and troubleshooting information.
See the HP Jetdirect Print Servers Administrator’s Guide for your print server model to interpret and
troubleshoot other messages.
Preconfigure network settings if required
If your network requires that you configure network settings before you add the printer to your network
systems, you can do so now.
However, in most cases, you can skip this section. Instead, you can proceed directly to the next section to
install the printer on your network computer systems. The network installation software will allow you to
configure basic network settings and add the printer to your system configuration.
Tools for preconfiguration
The following tools can be used to preconfigure your network settings.
●
The front panel
●
The Embedded Web Server
●
You can use an advanced configuration method, such as BootP, DHCP, Telnet, or the arp and ping
commands. For instructions, see the HP Jetdirect Print Servers Administrator’s Guide for your print
server model.
After the printer is configured with network settings, the configuration values are saved and maintained even
after it is turned off and on again.
Troubleshooting
IO Configuration page
The IO Configuration page provides comprehensive print server status. It is an important diagnostic tool,
especially if network communications are not available. For a description of messages that may appear on
the IO Configuration page, see the HP Jetdirect Print Servers Administrator’s Guide for your print server
model.
LEDs
The printer has status lights (LEDs) that indicate the link status and network activity.
26Chapter 1 IntroductionENWW
●
When the green light is on, the printer has successfully linked to the network.
●
When the yellow light is blinking, there is network transmission activity.
Link troubleshooting
If the printer does not successfully connect to the network:
●
Both LEDs will be off.
●
LAN Error - Loss of Carrier will be indicated on the IO Configuration page.
If a link failure is indicated, try the following:
●
Check cable connections.
●
Print an IO Configuration page and check link settings.
ItemDescription
Port ConfigIf the printer is properly linked, this item has one of the following values:
●
10BASE-T HALF: 10 Mbps, half-duplex
●
10BASE-T FULL: 10 Mbps, full-duplex
●
100TX-HALF: 100 Mbps, half-duplex
●
●
If the printer is not properly linked, one of the following messages will appear:
●
●
Auto NegotiationIndicates whether auto-negotiation for link configuration is on or off.
●
●
Reset network parameters
Network parameters (for example, the IP address) can be reset to factory default values by a cold reset:
turning the printer off and on again. After a cold reset, print an IO Configuration page to confirm that factoryreset values have been assigned.
CAUTION:A factory-installed HP Jetdirect X.509 certificate will be saved over a cold reset to factory default
values. However, a Certificate Authority (CA) certificate that has been installed by the user to validate a
network authentication server will not be saved.
100TX-FULL: 100 Mbps, full-duplex
1000TX FULL
UNKNOWN: The printer is in an initialization state.
DISCONNECTED: A network connection has not been detected. Check network cables. Reconfigure
the link settings, or restart the printer.
ON (default): The printer will attempt to automatically configure itself onto the network at the
proper speed and communication mode.
OFF: You must manually configure the link speed and communication mode using the front panel.
Your settings must match those of the network for proper operation.
ENWWAdvanced network configuration27
Menu items
Menu itemSub-menu itemSub-menu itemValues and Description
TCP/IPHost NameAn alphanumeric string, up to 32 characters, used to
identify the device. This name is listed on the HP Jetdirect
configuration page. The default host name is NPIxxxxxx,
where xxxxxx is the last six digits of the LAN hardware
(MAC) address.
IPV4 SettingsConfig MethodSpecifies the method that TCP/IPv4 parameters will be
configured on the HP Jetdirect print server.
Bootp: Use BootP (Bootstrap Protocol) for automatic
configuration from a BootP server.
DHCP (default): Use DHCP (Dynamic Host Configuration
Protocol) for automatic configuration from a DHCPv4
server. If selected and a DHCP lease exists, DHCP Release
and DHCP Renew menus are available to set DHCP lease
options.
Auto IP: Use automatic link-local IPv4 addressing. An
address in the form 169.254.x.x is assigned
automatically.
Manual: Use the Manual Settings menu to configure TCP/
IPv4 parameters.
DHCP ReleaseThis menu appears if Config Method was set to DHCP and
a DHCP lease for the print server exists.
No (default): The current DHCP lease is saved.
Yes: The current DHCP lease and the leased IP address
are released.
DHCP RenewThis menu appears if Config Method was set to DHCP and
a DHCP lease for the print server exists.
No (default): The print server does not request to renew
the DHCP lease.
Yes: The print server requests to renew the current DHCP
lease.
Manual Settings(Available only if Config Method is set to Manual)
Configure parameters directly from the printer control
panel:
IP Address: The unique IP address of the printer (n.n.n.n).
Subnet Mask: The subnet mask for the printer (n.n.n.n).
Syslog Server: The IP address of the syslog server
(n.n.n.n) used to receive and log syslog messages.
Default Gateway: The IP address (n.n.n.n) of the gateway
or router used for communications with other networks.
Idle Timeout: The time period, in seconds, after which an
idle TCP print data connection is closed (default is 270
seconds, 0 disables the timeout).
28Chapter 1 IntroductionENWW
Menu itemSub-menu itemSub-menu itemValues and Description
Default IPSpecify the IP address to default to when the print server
is unable to obtain an IP address from the network during
a forced TCP/IP reconfiguration (for example, when
manually configured to use BootP or DHCP).
Auto IP: A link-local IP address 169.254.x.x is set.
Legacy: The address 192.0.0.192 is set, consistent with
older HP Jetdirect devices.
Primary DNSSpecify the IP address (n.n.n.n) of a Primary DNS Server.
NOTE: This item appears only if Manual configuration is
a higher priority than DHCP in the Config. Precedence
table, configured through the embedded Web server.
Secondary DNSSpecify the IP address (n.n.n.n) of a Secondary Domain
Name System (DNS) Server.
NOTE: This item will appear only if Manual
configuration is a higher priority than DHCP in the Config.
Precedence table, configured through the embedded
Web server.
IPV6 SettingsEnableUse this item to enable or disable IPv6 operation on the
print server.
Off: IPv6 is disabled.
On (default): IPv6 is enabled.
AddressUse this item to manually configure an IPv6 address.
Manual Settings: Use the Manual Settings menu to enable
and manually configure a TCP/ IPv6 address.
Enable: Select this item and choose On to enable manual
configuration, or Off to disable manual configuration.
Address: Use this item to type a 32 hexadecimal digit IPv6
node address that uses the colon hexadecimal syntax.
DHCPV6 PolicyRouter Specified: The stateful auto-configuration method
to be used by the print server is determined by a router.
The router specifies whether the print server obtains its
address, its configuration information, or both from a
DHCPv6 server.
Router Unavailable: If a router is not available, the print
server should attempt to obtain its stateful configuration
from a DHCPv6 server.
Always: Whether or not a router is available, the print
server always attempts to obtain its stateful
configuration from a DHCPv6 server.
Primary DNSUse this item to specify an IPv6 address for a primary DNS
server that the print server should use.
NOTE: This item will appear only if Manual
configuration is a higher priority than DHCP in the Config
Precedence table, configured through the embedded
Web server.
ENWWAdvanced network configuration29
Menu itemSub-menu itemSub-menu itemValues and Description
Secondary DNSUse this item to specify an IPv6 address for a secondary
DNS server that the print server should use.
NOTE: This item will appear only if Manual
configuration is a higher priority than DHCP in the Config
Precedence table, configured through the embedded
Web server.
Proxy ServerSpecifies the proxy server to be used by embedded
applications in the device. A proxy server is typically used
by network clients for Internet access. It caches Web
pages, and provides a degree of Internet security, for
those clients.
To specify a proxy server, enter its IPv4 address or fullyqualified domain name. The name can be up to 255
octets.
For some networks, you may need to contact your
Independent Service Provider (ISP) for the proxy server
address.
Proxy PortType the port number used by the proxy server for client
support. The port number identifies the port reserved for
proxy activity on your network, and can be a value from 0
to 65535.
InformationPrint Sec PageYes: Prints a page that contains the current security
settings on the HP Jetdirect print server.
No (default): A security settings page is not printed.
SecuritySecure WebFor configuration management, specify whether the
embedded Web server will accept communications using
HTTPS (Secure HTTP) only, or both HTTP and HTTPS.
HTTPS Required: For secure, encrypted communications,
only HTTPS access is accepted. The print server will
appear as a secure site.
HTTP/HTTPS optional: Access using either HTTP or HTTPS
is permitted.
NOTE: The factory default setting depends on the print
server model.
30Chapter 1 IntroductionENWW
Menu itemSub-menu itemSub-menu itemValues and Description
Reset SecuritySpecify whether the current security settings on the print
server will be saved or reset to factory defaults.
No (default): The current security settings are
maintained.
Yes: Security settings are reset to factory defaults.
Link SpeedThe link speed and communication mode of the print
server must match the network. The available settings
depend on the device and installed print server. Select
one of the following link configuration settings:
CAUTION: If you change the link setting, network
communications with the print server and network device
might be lost.
Auto (default): The print server uses auto-negotiation to
configure itself with the highest link speed and
communication mode allowed. If auto-negotiation fails,
either 100TX HALF or 10TX HALF is set depending on the
detected link speed of the hub/switch port. (A 1000T
half-duplex selection is not supported.)
10T Half: 10 Mbps, half-duplex operation.
10T Full: 10 Mbps, Full-duplex operation.
Embedded services
Key networking services embedded in the printer are listed below. For the latest features and services, visit
http://www.hp.com/go/jetdirect.
●
Configuration and Management
◦
BootP/DHCP (IPv4 only)
◦
DHCPv6
◦
TFTP (IPv4 only)
◦
Web Proxy (Automatic/Manual cURL)
◦
LLMNR
◦
Telnet (IPv4 only)
100TX Half: 100 Mbps, half-duplex operation.
100TX Full: 100 Mbps, full-duplex operation.
100TX Auto: Limits auto-negotiation to a maximum link
speed of 100 Mbps.
1000TX Full: 1000 Mbps, full-duplex operation.
◦
SNMP (v1, v2c, v3) agents
◦
Bonjour (for Mac OS X)
◦
FTP (File Transfer Protocol)
ENWWAdvanced network configuration31
◦
Embedded Web Server, HTTP (TCP port 80)
◦
Embedded Web Server, HTTPS (TCP port 443)
●
Printing
◦
Raw IP printing (HP-proprietary TCP ports 9100, 9101, 9102)
●
Security
◦
SNMP v3
◦
SSL/TLS
◦
Firewall
Turn the printer on and off
To turn on the printer, ensure that the power switch at the rear of the printer is turned on, then press the
power button beside the front panel.
You can leave the printer on without wasting energy. Leaving it on improves response time. When the printer
has not been used for a certain period of time, it saves power by going into sleep mode. Pressing the power
button returns it to active mode, and it can resume printing immediately.
To tun off the printer, the normal and recommended method is to press the power button.
When you turn off the printer this way, the printheads are automatically stored with the maintenance
cartridge, which prevents them from drying out.
However, if you plan to leave the printer turned off for a long period of time, you are recommended to turn it
off using the power button, and then also turn off the power switch at the rear.
To turn it back on later, use the power switch at the rear. If the printer does not start automatically, press the
power button.
32Chapter 1 IntroductionENWW
When the printer is turned on, it takes 2–3 minutes to initialize itself.
Restart the printer
In some circumstances you may be advised to restart the printer.
1.Turn off the printer by pressing the power button and then turning off the power switch at the rear of
the printer.
2.Wait for at least 10 seconds.
3.Turn on the power switch at the rear of the printer.
4.If the front panel does not activate, press the power button.
User training (quick guide) is already installed in your computer. To reinstall: http://www.hp.com/go/
latex110/quickguide/
Videos about how to use the printer: http:/www.hp.com/supportvideos/ or http://www.youtube.com/
HPSupportAdvanced
Substrate presets: http://www.hp.com/go/mediasolutionslocator (see HP Media Locator on page 73)
HP Support: http://www.hp.com/go/latex110/support/
Embedded Web Server: Use the printer’s IP address (see Access the Embedded Web Server on page 19)
Registration and communication with HP: http://www.hp.com/communities/HPLatex/.
When you need help
Contact HP Support on the Web as shown above.
Help is also available to you by telephone. What to do before you call:
●
Review the troubleshooting suggestions in this guide.
●
Review your RIP's documentation, if relevant.
●
Please have the following information available:
◦
The printer you are using: the product number, the serial number and the service ID
NOTE:
label at the rear of the printer.
◦
If there is an error code on the front panel, note it down; see Front-panel error codes on page 137
◦
The RIP you are using, and its version number
◦
If you have a print-quality problem: the substrate reference, and the name and origin of the
substrate preset used to print on it.
◦
The service information report (see Service information on page 35)
This information is available from the front panel: press . You may also find it on a
Telephone number
Your HP Support telephone number is available on the Web: see http://www8.hp.com/us/en/contact-hp/ww-
phone-assist.html.
34Chapter 2 Useful linksENWW
Customer Self Repair
HP's Customer Self Repair program offers our customers the fastest service under either warranty or
contract. It enables HP to ship replacement parts directly to you (the end user) so that you can replace them.
Using this program, you can replace parts at your own convenience.
Convenient, easy to use
●
An HP Support Specialist will diagnose and assess whether a replacement part is required to address a
defective hardware component.
●
Replacement parts are express-shipped; most in-stock parts are shipped the very same day you contact
HP.
●
Available for most HP products currently under warranty or contract.
●
Available in most countries.
For more information about Customer Self Repair, see http://www.hp.com/go/selfrepair/.
Service information
The printer can produce on request a list of many aspects of its current status, some of which may be useful
to a service engineer trying to fix a problem. There are two different ways to request this list:
●
In the Embedded Web Server (see Access the Embedded Web Server on page 19), select the Support tab
and then Service support > Printer information. You are recommended to request the whole list
(select All pages).
●
From any computer with Internet access, enter the URL of your printer into a Web browser, followed
by /hp/device/webAccess/allServicePlot.htm. For instance, if the URL of your printer is
If you need to send the list by email, you can save the page as a file from your Web browser, and later send
the file. Alternatively, from Internet Explorer you can send the page directly: select File > Send > Page by email.
ENWWWhen you need help35
3Handle the substrate and troubleshoot
substrate issues
●
Overview
●
Porous substrates
●
Load a roll onto the spindle
●
Load a roll into the printer
●
Assisted manual load
●
The edge holders
●
Load a cut sheet into the printer
●
How to cut substrate
●
Unload a roll from the printer
●
The take-up reel (accessory)
●
View information about the substrate
●
Change substrate width and right edge position
●
Substrate length tracking
●
Bypass job start safety
●
Store the substrate
●
The substrate cannot be loaded successfully
●
The substrate is mispositioned
●
The substrate has jammed
●
The substrate is deformed or wrinkled
●
The substrate has shrunk or expanded
●
The substrate has bow deformation
●
Take-up reel substrate jam
●
Take-up reel does not wind
36Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
Overview
You can print on a wide variety of printing materials, all of which are referred to in this guide as substrates.
Substrate tips
Choosing the correct substrate for your needs is an essential step in ensuring good print quality.
Here are some tips about substrate usage.
●
Using the take-up reel with some substrates may give the printer better control of the substrate and is
likely to improve print quality. See
●
Allow all substrates to adapt to room conditions, out of the packaging, for 24 hours before using them
for printing.
●
Handle film and photo substrates by the edges, or wear cotton gloves. Skin oils can be transferred to
the substrate, leaving fingerprint marks.
●
Keep the substrate tightly wound on the roll throughout the loading and unloading procedures. To
make sure that the roll stays tightly wound, consider using tape to stick the leading edge of the roll to
the core just before removing the roll from the printer. You can keep the roll taped during storage. If the
roll starts to unwind, it can become difficult to handle.
NOTE:The use of tape to stick the leading edge of the roll to the core is especially important for heavy
substrates, because the inherent stiffness of the substrate can cause it to loosen and unwind from the
core.
The take-up reel (accessory) on page 55.
●
Print quality could be impaired if you use a substrate that is unsuitable for your image.
●
Make sure that the appropriate print-quality setting is selected in the RIP.
●
Whenever you load a roll, the front panel prompts you to specify the substrate type that you are
loading. For good print quality, it is essential to specify this correctly. Check that the substrate name is
the same in the front panel and in the RIP.
If the names are not the same, press on the front panel, then Substrate > Change loaded
substrate
●
Do not pull the printed substrate while the printer is printing: this can cause severe print-quality
defects.
; or change the substrate in the RIP.
ENWWOverview37
●
When printing a series of jobs, do not let the printed substrate obstruct the output path: this can cause
severe print-quality defects.
●
For more substrate tips, see Load a roll into the printer on page 46 and Assisted manual load
on page 49.
CAUTION:Removing the substrate from the printer manually without using the front panel could damage
the printer. Do this only when necessary to clear a substrate jam.
outdoor, windows, bus
shelters, billboards,
wall decorations
Yes
Yes
124 microns (4.9 mil) • 90 g/m² • 61 m (200 ft)
40Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
CategorySubstrateColor
calib.
Applications
New HP Coated Paper, 3 in core
114 microns (4.5 mil) • 90 g/m² • 61 m (200 ft)
New HP Universal Heavyweight Coated Paper, 3 in core
165 microns (6.5 mil) • 125 g/m² • 61 m (200 ft)
New HP Heavyweight Coated Paper, 3 in core
167 microns (6.6 mil) • 130 g/m² • 61 m (200 ft)
New HP Super Heavyweight Plus Matte Paper, 3 in core
259 microns (10.2 mil) • 210 g/m² • 61 m (200 ft)
New HP Professional Gloss Photo Paper
See http://www.globalbmg.com/hp/
New HP Professional Satin Photo
See http://www.globalbmg.com/hp/
New HP Everyday Satin Photo Paper
See http://www.globalbmg.com/hp/
●
For third-party substrate solutions with ColorPRO technology, please visit
http://ColorPROtechnology.com/.
Yes
Yes
Yes
Yes
●
HP PVC-free Wall Paper imprimé avec les encres HP Latex est classé A+ selon l’arrêté du 19 avril 2011
« Émissions dans l'air intérieur », qui définit des seuils sur l’émission de polluants volatils posant des
problèmes en cas d’inhalation – sur une échelle de A+ (émission très basses) à C (émission élevée).
●
HP PVC-free Wall Paper printed with HP Latex Inks is rated A+ according to Émissions dans l'air intérieur,
which provides a statement of the level of emission of volatile substances in indoor air posing health
risks if inhaled—on a scale from A+ (very low emission) to C (high emission).
* HP PVC-Free Wall Paper printed with HP Latex Inks is GREENGUARD Children & Schools Certified. See
http://www.greenguard.org/.
* HP PVC-Free Wall Paper printed with HP Latex Inks meets AgBB criteria for health-related evaluation of VOC
emissions of indoor building products. See http://www.umweltbundesamt.de/produkte-e/bauprodukte/
agbb.htm.
HP large-format substrate take-back program availability varies. Some recyclable HP substrates can be
recycled through commonly available recycling programs. Recycling programs may not exist in your area.
http://www.hp.com/recycle/ for details.
See
Porous substrates
The printer is not designed to be used with porous substrates, and could be damaged by them, requiring a
service repair not covered by your warranty.
To check the porosity of your substrate, proceed as follows.
1.If the printer has any substrate loaded, unload it.
2.Cut a piece of self-adhesive vinyl white gloss 15 × 50 mm (0.6 × 2 in) in size.
ENWWPorous substrates41
3.Stick it to the platen as shown.
4.Load the substrate that you want to check.
5.Open your RIP software.
6.Download the test file from inside the printer: http://printerIP/hp/device/webAccess/images/
Ink_trespassing_check.pdf, where printerIP is the IP address of your printer.
7.Print the test file using the number of passes and substrate preset that you intend to use in future with
this substrate (or a similar profile in terms of ink limit).
8.Unload the substrate.
9.Remove the strip of self-adhesive vinyl from the platen.
10. Look at the self-adhesive vinyl you have taken from the platen.
●
If the strip is completely white (has no ink on it), the tested substrate is non-porous and can be
used for printing as described in this guide.
●
If there some ink on the strip, the tested substrate is porous and should not be used.
11. Clean the platen: see Clean the platen on page 125.
Load a roll onto the spindle
TIP:As an alternative to the description here, you can see an animation of this procedure in the front panel:
press , then Substrate > Substrate load > Learn how to load spindle.
1.Make sure that the printer wheels are locked (the brake lever is pressed down) to prevent the printer
from moving.
42Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
2.Lift the spindle lock lever to disengage the spindle.
3.Remove the spindle from the printer.
CAUTION:Do not insert your fingers into the spindle supports.
The spindle has a stop at each end to keep the roll in position. Remove the blue stop at the left end to
mount a new roll (the stop at the other end of a 3 in (76 mm) diameter spindle can also be removed, if
you wish). The stop slides along the spindle to hold rolls of different widths.
NOTE:If you have a 2 in (51 mm) spindle, you can use the 3-in adaptor.
4.Unlock the blue stop.
ENWWLoad a roll onto the spindle43
5.Remove the stop from the left end of the spindle.
6.Place the roll onto the loading table.
7.Slide the spindle into the roll.
44Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
8.The 51 mm (2 in) diameter spindle has only one position for the right stop. There are blue lines on the
loading table corresponding to two positions, but when using this spindle you can use only the outer
position.
9.Put the blue stop on to the upper end of the spindle, and push it towards the end of the roll.
10. Lock the blue stop when it is in contact with the substrate.
11. Insert the spindle carefully into the printer.
WARNING!Avoid trapping your fingers between the spindle and the spindle supports.
Risk of trapped fingers
For more safety information, please see Safety precautions on page 3
ENWWLoad a roll onto the spindle45
CAUTION:Ensure that the sliders in the loading table are under the left hub, otherwise the spindle will
not enter correctly into the left spindle support, and could fall on the floor.
If you regularly use different substrates, you can change rolls more quickly if you pre-load rolls of different
substrates on different spindles. Extra spindles are available for purchase.
Load a roll into the printer
To start this procedure, you need to have a roll loaded on the spindle. See Load a roll onto the spindle
on page 42.
The normal minimum substrate width is 23 inches (584 mm). To load substrates down to a minimum width of
10 inches (254 mm), go to the front panel and press , then Substrate > Substrate handling options >
Enable narrow substrate. With this option, print quality is not guaranteed.
TIP:When loading very thin or very thick substrates, or substrates with a tendency to curl, you should
follow the manual loading procedure to reduce the risk of substrate jams and printhead crashes; see Assisted
manual load on page 49.
1.
At the printer's front panel, press , then Load.
Alternatively, press , then Substrate load > Load roll.
46Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
2.The load configuration screen appears.
●
Skew acceptance: The available values are between 1 and 5, default 3. The printer warns you if the
skew is over the limit you have set, but you can still choose to continue loading.
●
Length tracking: If you check the box and give the length of your roll, the printer reduces the spare
paper when printing and tells you the remaining length. See Substrate length tracking
on page 62.
●
Assisted manual load. See Assisted manual load on page 49.
●
Use edge holders. See The edge holders on page 51.
When you have made your choices, instructions are displayed.
3.Carefully insert the leading edge of the substrate above the smooth black roller, making sure the
substrate remains taut during the process. Avoid rewinding the substrate manually, unless the printer
asks you to do so.
WARNING!Take care not to insert your fingers inside the printer's substrate path.
The printer beeps when it detects and accepts the leading edge of the substrate.
ENWWLoad a roll into the printer47
4.Select the category and name of the substrate you are loading.
You can also search by favorites, or you can select None of these, I will choose it later: by accessing
the substrate library after completing the loading procedure. See Substrate presets on page 71.
NOTE:You should select the same substrate name that you are using in your RIP software.
5.The printer checks the substrate in various ways and may ask you to correct problems with skew or
tension.
6.Wait until the substrate emerges from the printer, as shown below.
WARNING!Take care not to touch the curing zone or the platen, which may be hot.
Risk of burns
For more safety information, please see Safety precautions on page 3
NOTE:If you have an unexpected problem at any stage of the substrate loading procedure, see The
substrate cannot be loaded successfully on page 63.
7.If you are loading transparent substrate without opaque borders, you are asked to enter the width of
the substrate and the distance of the right edge from the printer's side plate (as indicated by the ruler
on the front of the curing module).
48Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
8.The printer indicates that it is ready for printing.
Take care not to cover the top fans.
For instructions on how to use the take-up reel, see The take-up reel (accessory) on page 55.
Assisted manual load
The assisted manual load procedure should be used in the following cases:
●
The substrate is unusually thin or unusually thick.
●
The substrate has ragged edges.
●
The substrate tends to curl at the edges.
●
The printing side of the substrate faces outwards.
In other cases, you are recommended to use the normal loading procedure. See Load a roll into the printer
on page 46.
To start the assisted manual load procedure, you need to have a roll loaded on the spindle. See Load a roll
onto the spindle on page 42.
The normal minimum substrate width is 23 inches (584 mm). To load substrates down to a minimum width of
10 inches (254 mm), go to the front panel and press , then Substrate > Substrate handling options >
Enable narrow substrate. With this option, print quality is not guaranteed.
1.Start the substrate loading procedure as usual (see Load a roll into the printer on page 46), and make
sure to check the Assisted manual load box in the load configuration screen.
ENWWAssisted manual load49
You can alternatively begin at step 2, in which case the load configuration screen will appear with this
checkbox checked after you lift the pinch lever. Press Continue before taking the next step.
2.Lift the substrate pinch lever as far up as it will go.
3.Carefully insert the leading edge of the substrate above the smooth black roller, making sure the
substrate remains taut during the process. Avoid rewinding the substrate manually, unless the printer
asks you to do so.
4.Continue to feed the substrate until it reaches the printing platen. Open the window to help pull the
substrate through, and keep feeding the substrate at least until the leading edge is at the same height
as the substrate roll. Align the right edge of the substrate with the right edge of the roll.
WARNING!Do not touch the printer's curing enclosure. Even after you have opened the window latch,
which disconnects the power to the curing modules, the internal surfaces could be hot. Also beware of
getting your fingers trapped in the substrate path.
Risk of burnsRisk of trapped fingers
For more safety information, please see Safety precautions on page 3
TIP:If the substrate you are using tends to curl, keep feeding the substrate until the edge is out of the
printer. You are also recommended to use the take-up reel, if you have purchased it as an accessory.
50Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
5.Once the substrate is correctly fed into the printer, pull down the substrate pinch lever as far as it will
go.
6.Select the category and name of the substrate you are loading.
The rest of the assisted load procedure is the same as in the normal load procedure. See Load a roll into the
printer on page 46.
The edge holders
The edge holders are designed to prevent the edges of the substrate from rising while printing is in progress.
They are not normally necessary. When not in use, they should be stored inside the printer, to the left and
right respectively, to avoid substrate jams. It is also a good idea to store the edge holders when no substrate
is loaded, in case you later forget and leave them installed by mistake.
NOTE:The edge holders extend 7 mm over the edge of the substrate. You should set a minimum left and
right margin of 7 mm (0.3 in) in the RIP when using edge holders, otherwise the printer could try to print on
the edge holders.
If you choose to use them, you should move them into position when prompted by the front panel (this
prompt appears when the Use edge holders checkbox has been checked). Open the window, place the edge
holders, then close the window.
The edge holders should be placed on the platen so that they slightly overlap the left and right edges of the
substrate. There are marks on the printer to show where to place them.
The edge holders for each printer model are the same, but they are installed in different ways.
WARNING!Avoid moving parts. Handle fragile parts with care. You are recommended to wear gloves.
ENWWThe edge holders51
Place edge holders
1.There is a hole on the left for the edge holders. Insert an edge holder vertically into the hole.
2.Slide the edge holder into its correct position.
Moving partFragileWear gloves
For more safety information, please see Safety precautions on page 3
3.Repeat with the other edge holder.
Align the substrate
When the substrate has been loaded, align it with the white line on the edge holder. Misalignment could
result in a substrate jam, or damage to the substrate or to the printheads.
52Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
Load a cut sheet into the printer
The printer is designed to be used with rolls of substrate. It is possible to load cut sheets into the printer, but
print quality cannot be guaranteed, and you may have some difficulty in avoiding skew.
●
The sheet should be at least 1067 mm (42 in) long.
●
Load the sheet by following the normal roll loading procedure (automatic or manual, depending on the
substrate).
●
During the loading procedure, the printer tries to detect the winding direction of the roll by turning the
spindle in both directions. When the substrate is not attached to the spindle, the following message
appears.
●
A cut sheet is likely to be loaded with excessive skew, and the printer may not be able to correct it
automatically. If the skew as measured by the printer exceeds 3 mm/m, you are recommended to
reload the sheet. However, if the skew is tolerable, you can consider skipping the automatic skew
correction. To do so, when prompted, choose Continue with current skew.
How to cut substrate
To cut the substrate, open the window and cut the substrate using the slot indicated below. Ensure that the
substrate is under tension while cutting.
CAUTION:Use a safety cutter.
ENWWLoad a cut sheet into the printer53
CAUTION:Do not place your hand below the cutter. Be very careful not to cut yourself.
Unload a roll from the printer
1.If you used the take-up reel during printing, unload the printed roll from the take-up reel. See Unload
the take-up reel on page 61.
2.
On the printer's front panel, press , then Unload.
Alternatively, you can press , then Substrate > Unload substrate.
3.If the printer has been tracking the length of the substrate, the front panel displays the remaining
length so that you can note it for future reference. See Substrate length tracking on page 62.
Press OK to continue.
4.When the printer has rewound the roll, lift the spindle lock lever.
5.Remove the spindle from the printer, pulling out the right end on the right side of the printer first.
WARNING!Do not insert your fingers into the spindle supports while removing the spindle.
Risk of trapped fingers
For more safety information, please see Safety precautions on page 3
54Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
The take-up reel (accessory)
The tension bar
When in use, the take-up reel requires a dangling loop of substrate weighed down by a tension bar. The
tension bar can be moved with the take-up reel buttons or by using the Move paper or Rewind paper options
in the front panel.
Load a roll onto the take-up reel
NOTE:Take-up reels with 51 mm (2 in) or 76 mm (3 in) diameter can be used.
1.
On the printer's front panel, press , then Take-up reel.
Instructions are displayed on the screen; slide your finger laterally across the front panel to follow the
instructions to the end.
2.If you decide to load the take-up reel during printing, familiarize yourself with the procedural steps
before pressing the Enable button. Loading the take-up reel during printing requires you to complete
the procedure while the printer is feeding and printing substrate. Loading the take-up reel during
printing saves approximately 1.5 m (4.9 ft) of substrate.
TIP:You are recommended to keep the take-up reel winding-direction switch in the off position (see
Unload the take-up reel on page 61) to avoid unwanted movements when loading the take-up reel
while printing. Once you have the leading edge of the substrate attached to the core, and the substrate
is straight, switch the winding-direction switch to position 1 or 2, as you prefer. Setting 1 winds the
substrate so that the printed image faces in, setting 2 winds the substrate so that the printed image
faces out.
The following steps assume that you have decided to load immediately. If you decide to load later,
during printing, you must complete the same operations without guidance from the front panel.
ENWWThe take-up reel (accessory)55
3.For easier access to the take-up reel, lift the loading table into its upright position.
4.Unlock the take-up reel by pushing its lever to the uppermost position.
5.Remove the take-up reel.
6.Load the core onto the take-up reel. The core should be at least as wide as the substrate.
7.Load the take-up reel into the printer by pushing firmly on both ends.
56Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
WARNING!Take care not to get your fingers trapped.
Risk of trapped fingers
For more safety information, please see Safety precautions on page 3
8.Advance the substrate by pressing the Move substrate button on the front panel. Make sure that the
substrate passes in front of the loading table.
9.Pull down the center of the substrate's leading edge to straighten the substrate. Do not attempt to pull
more substrate out of the printer.
NOTE:If you are loading the take-up reel during printing, you do not need to pull the substrate taut.
Tape the substrate to the core when an adequate length of substrate has fed from the printer after
printing begins.
WARNING!Do not touch the printer's curing enclosure, which could be hot.
Risk of burns
For more safety information, please see Safety precautions on page 3
ENWWThe take-up reel (accessory)57
10. Adjust the position of the core on the take-up reel so that it is aligned with the substrate.
11. Tape the leading edge of the substrate to the core in the center, then at each side. Make sure that the
substrate is straight.
NOTE:Depending on whether you want to print the images facing in or out, place the tape
accordingly. See below.
12. Press the button on the front panel to advance the substrate, creating a loop.
58Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
13. Press the blue arrow on the take-up reel motor to rotate the reel one full turn. This will help to support
the weight of the tension bar.
14. Press the button on the front panel to advance the substrate again.
15. Gently lower the loading table, to avoid wrinkles and improve winding.
ENWWThe take-up reel (accessory)59
16. Carefully insert the tension bar. This is essential: the take-up reel will not function correctly without it.
17. Fit the tension bar into the supports at either side.
WARNING!Take care not to get your fingers trapped.
Risk of trapped fingers
For more safety information, please see Safety precautions on page 3
18. Use the winding-direction switch on the take-up reel motor to select the winding direction. Setting 1
winds the substrate so that the printed image faces in. Setting 2 winds the substrate so that the printed
image faces out.
60Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
19. Press the Enable button on the front panel.
20. The following image shows how the printer looks when it is operating. As substrate is fed from the
printer, it drops down to the tension bar, over the diverter, then down again to the take-up reel.
NOTE:When the take-up reel is in use, the substrate is not automatically cut after each print.
Unload the take-up reel
WARNING!Take care not to get your fingers trapped.
Risk of trapped fingers
For more safety information, please see Safety precautions on page 3
1.
On the printer's front panel, press , then Take-up reel.
The printer allows you to move the substrate to facilitate cutting.
2.Switch the winding-direction switch to the off position. The switch is in the off position when it is
centered (in other words, when the switch is neither in position 1 nor position 2).
3.To remove the tension bar, first lift the support, then press the lever.
4.Use the winding button on the take-up reel motor to wind the excess substrate around the take-up reel.
5.Cut the substrate with scissors.
6.While holding the substrate, use the winding button on the take-up reel motor to wind the remainder of
the substrate around the take-up reel.
7.Unlock the take-up reel by pushing its lever to the uppermost position.
8.Remove the take-up reel from the printer, pulling out the end on the right side of the printer first.
9.To remove the roll from the printer after you have unloaded the take-up reel, see Unload a roll from the
printer on page 54.
ENWWThe take-up reel (accessory)61
View information about the substrate
On the front panel's home screen, press .
The following information appears on the front panel, if any substrate is loaded:
●
The substrate type
●
The substrate name
●
The substrate width in millimeters (estimated by the printer)
●
The remaining length of the substrate, if known
●
The printing zone
●
The take-up reel status
●
The color calibration status
If no substrate is loaded, the message Out of substrate appears.
The same information appears on the Embedded Web Server's Supplies page.
Change substrate width and right edge position
If the substrate edges are not correctly found by the printer, they can be changed from the front panel by
pressing , then Substrate > Substrate handling options > Substrate width or Right edge position.
TIP:Bear in mind that automatic edge detection will not be attempted again until the next substrate load.
Substrate length tracking
The substrate length tracking feature enables you to keep track of how much substrate remains on the roll.
1.When the roll is first loaded onto the printer, you have the option (in the Load Configuration screen) to
enter the length of substrate on the roll. The amount of substrate that is subsequently used is then
tracked.
2.When the substrate is unloaded, the front panel displays the amount remaining so that you can note it
for future reference.
The remaining length of substrate is always displayed in the Substrate area of the front panel. This
information may also be displayed in your RIP.
Bypass job start safety
The job start safety mode is activated by default so that the leading edge of the substrate does not crash
under the curing system.
62Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
If you print with the substrate hanging from the front of the printer, or using the take-up reel, you may want
to deactivate this option to improve throughput. To do that, press , then Substrate > Substrate
handling options
> Bypass job start safety.
Store the substrate
The following are tips for storing substrate:
●
Always keep unused rolls wrapped in the plastic wrap to prevent discoloration and dust accumulation.
Rewrap partially used rolls if they are not being used.
●
Do not stack rolls.
●
Allow all substrates to adapt to room conditions out of the packaging for 24 hours before printing.
●
Handle film and glossy substrates by the edges or wear cotton gloves. Skin oils can be transferred to
the substrate, leaving fingerprint marks.
●
Keep the substrate tightly wound on the roll throughout the loading and unloading procedures. If the
roll starts to unwind, it can become difficult to handle.
The substrate cannot be loaded successfully
Here are some suggestions to try if you cannot load the substrate successfully.
●
Reread the loading instructions, and make sure that you are following them. See Handle the substrate
and troubleshoot substrate issues on page 36.
●
If automatic loading is unsuccessful, try assisted manual loading instead.
●
The substrate might be loaded at an angle (skewed or mislocated). Make sure that the right edge of the
substrate is aligned with the roll on the input spindle.
●
The substrate might be crumpled or warped, or have irregular edges. See The substrate is deformed or
wrinkled on page 67.
●
If the substrate jams in the substrate path to the platen, the leading edge of the substrate might not be
straight or clean. Remove the initial 2 cm (1 in) of substrate from the roll and try again. This might be
necessary even with a new roll of substrate.
●
Make sure that the spindle is correctly inserted.
●
Make sure that the substrate is correctly loaded on the spindle.
●
Make sure that the substrate is wound tightly.
ENWWStore the substrate63
The substrate is mispositioned
If you see the above display on the front panel, proceed as follows.
1.Lift the substrate lever.
2.Manually reposition the substrate on the platen.
3.Lower the substrate lever.
4.Repeat the above steps until the front panel displays the Ready message.
The substrate has jammed
When a jam occurs, the Possible substrate jam message usually appears in the front panel, with one of
several error codes (see Front-panel error codes on page 137).
If you are trying to load a very thin or very thick substrate, or a textile, remember to follow the special
procedure for loading such substrates..
Check the substrate path
This problem can occur when a roll has finished and the end of the roll is stuck to the cardboard core. If this
has happened, cut the end of the roll away from the core. Then feed the substrate through the printer, and
load a new roll.
Otherwise:
1.Turn off the printer at the front panel, then also switch off the power switch at the rear.
64Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
2.Open the printer window.
3.Cut the substrate where it enters the printer, and rewind the input roll.
4.Try to move the printhead carriage out of the way.
5.Lift the substrate pinch lever as far up as it will go.
6.Carefully remove as much as possible of the jammed substrate from the top of the printer. Cut the
substrate if necessary.
ENWWThe substrate has jammed65
CAUTION:Try to avoid pulling the substrate out through the input path, because this reverses the
normal direction of movement, and could damage printer parts.
WARNING!Do not touch the printer's curing enclosure, which could be hot.
Risk of burns
For more safety information, please see Safety precautions on page 3
7.Lower the substrate pinch lever.
8.Make sure that there are no pieces of substrate left in the printer. In particular, check in and under the
curing module, and in the substrate path.
9.Close the window.
10. Turn on the printer.
11. Reload the roll.
12. If some substrate continues to cause an obstruction within the printer, it can often be cleared by loading
a rigid substrate type into the printer.
13. If you find that you have print-quality problems after a jam, try realigning the printheads. See Align the
printheads on page 106.
Avoiding substrate jams while printing
Substrate jams may be caused by loading the substrate with too much skew: do not ignore the warning
message that appears during the loading procedure in this case.
They may also be caused by not enough vacuum suction in the printing zone. If you decide to increase the
suction, do not exceed the following limits: 20 mmH2O for banners, 35 mmH2O for vinyl, and 50 mmH2O for
other substrate families.
If you experience jams only at the beginning of a print, try the following suggestions.
66Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
●
Go to the front panel and press , then Substrate handling options > Extra bottom margin and
Extra top margin. Set both margins to 100 mm. If that is not enough, try higher values.
●
Increase the vacuum level in steps of 10 mmH2O. Do not exceed the following limits: 20 mmH2O for
banners, 45 mmH
Consider reducing the vacuum percentage at the front of the print zone for thin substrates.
●
Increase the number of passes.
●
Make sure that the substrate is stored in the same room in which the printer is located.
●
Try using the substrate edge holders.
O for vinyl, and 60 mmH2O for other substrate families.
2
The substrate is deformed or wrinkled
If your substrate is deformed or wrinkled by the curing process, change the temperature settings before
printing the next job, and advance the substrate, using the Move substrate option in the front panel's
Substrate menu, so that the next job will be printed on undamaged substrate.
If the problem appears only at the beginning of the print, try the following suggestions.
●
Go to the front panel and press , then Substrate handling options > Extra bottom margin and
Extra top margin. Set both margins to 100 mm. If that is not enough, try higher values.
●
Increase the vacuum level in steps of 10 mmH2O. Do not exceed the following limits: 20 mmH2O for
banners, 45 mmH2O for vinyl, and 60 mmH2O for other substrate families.
●
Increase the number of passes.
●
Make sure that the substrate is stored in the same room in which the printer is located.
The substrate has shrunk or expanded
During the printing process, some substrates may shrink, while others may expand. If this happens, the
dimensions of the print will not be correct.
As a general rule, you can expect the following percentages of shrinkage:
●
Banner: less than 2%
●
Self-adhesive vinyl: less than 0.5%
●
Backlit: less than 0.5%
●
Paper: less than 0.5%
●
PP & PE synthetics: less than 1%
The framing problem may be solved by printing a sample and adjusting the size of the image in the RIP. You
may reuse this value for all your future prints with the same substrate, although special care must be taken
when using banners, as the shrinkage may vary up to 1% depending on the amount of ink used in the print.
You can expect the following variations from one print to another:
●
Banner: less than 0.3%
●
Self-adhesive vinyl: less than 0.1%
●
Backlit: less than 0.05%
ENWWThe substrate is deformed or wrinkled67
●
Paper: less than 0.1%
●
PP & PE synthetics: less than 0.4%
You are recommended to tile together areas with similar amounts of ink. If this is not possible, print the
areas with different amounts of ink as different jobs and modify the length of the job with less ink in the RIP
to match its size with the job with high ink content.
Some RIPs may provide a scaling option that allows you to compensate easily for substrate shrinkage or
expansion; see your RIP documentation.
The substrate has bow deformation
The following substrates may suffer from bow deformation during printing, as a result of which the print will
appear curved.
●
Self-adhesive vinyl substrates (some specific calendared vinyls only)
●
Cellulose-based poster papers with no backing nor coating
This deformation may be particularly noticeable in the following applications.
●
Printing images that will later be cut automatically or manually. When there is bow deformation, cutters
that are aligned on the sides may lose alignment in the center.
●
Poster printing, if the poster is framed or mounted on a straight surface.
The example below shows an original image, the substrate suffering from bow deformation, and the
resulting print, also suffering from bow deformation.
You can compensate for this effect and restore the original shape of your image: select a correction value
from −6 to +6 in your RIP or in the substrate library. To apply the correction in your RIP, please refer to your
RIP documentation.
The chosen value should represent the vertical distance that the centre of the substrate has moved with
respect to the left and right edges. If the deformation moves the center of the substrate in the direction of
substrate advance, the correction value should be negative; if in the reverse direction, the correction value
should be positive. In practice, the required correction value is normally negative.
TIP:You can use the diagnostic image provided in http://IPaddress/hp/device/webAccess/diagnostic/
StraightnessOptimizationPlot.pdf (where IPaddress is the IP address of your printer) to help you to
determine the correct value to apply.
Take-up reel substrate jam
Cut the substrate as close as possible to the printer window, then remove the roll.
If the problem remains after removing the substrate jam, unload the take-up reel from the front panel and
load it again.
68Chapter 3 Handle the substrate and troubleshoot substrate issuesENWW
Take-up reel does not wind
Predictably, if the take-up reel is not winding as anticipated, the printed output is likely to end up on the
floor. If the printer recognizes a problem with the take-up reel, it interrupts the print job until the issue is
corrected. If the printer does not recognize a problem, the job continues to print. The following table
highlights possible issues and solutions.
Take-up reel LED status IssuePrint job interrupted?Possible causePossible solution
Blinking quicklyTake-up reel is not
winding
Blinking slowlyTake-up reel is not
winding
Solid redTake-up reel is not
winding
Solid greenTake-up reel is not
winding
Solid greenTake-up reel is winding
in the wrong direction
YesThe tension bar is in its
lower position because
the winding direction is
not correct.
NoThe sensor cables are
loose or unplugged.
NoThere is too much
resistance on the takeup reel motor.
NoThe winding-direction
switch on the take-up
reel motor is Off or in
the wrong position.
NoThe winding-direction
switch on the take-up
reel motor is in the
wrong position.
Change the winding
direction using the
winding-direction switch
on the take-up reel
motor. You may need to
use the blue arrow
buttons to collect
substrate from the floor.
Ensure that the sensor
cables are correctly
secured.
Ensure that nothing is
blocking the substrate
path or the tension bar.
Ensure that the switch is
On, and select the
correct winding direction
(1 or 2).
Change the switch to the
correct position.
ENWWTake-up reel does not wind69
4Substrate settings
●
Substrate presets
●
Online search
●
HP Media Locator
●
Generic presets
●
Clone a substrate preset
●
Modify a substrate preset
●
Add a new substrate
●
Delete a substrate preset
●
Faster printing
●
Color calibration
●
ICC profiles
70Chapter 4 Substrate settingsENWW
Substrate presets
Each substrate type has its own characteristics. To obtain the best print quality, the printer has to adapt its
printing parameters to each different substrate type. For example, some may need more ink and some may
require higher temperatures for curing. A specification of the correct printing parameters for a particular
substrate type is called a substrate preset.
The substrate preset contains a color profile in International Color Consortium (ICC) format, which describes
the color characteristics of the combination of printer, inks, and substrate. It also contains information about
other parameters (such as curing temperature, vacuum pressure, and substrate-advance compensation) that
are not directly related to color. Substrate presets (also known as Open Media System or OMES packages) are
installed in the printer, and automatically copied to supported RIP software whenever it is connected to the
printer.
The printer comes with substrate presets for the most commonly used generic and specific substrates. If you
load a substrate for which no specific preset is available in the printer, you have various options:
●
Use the Online search function on the front panel or the HP Media Locator on the Web to browse,
search, and download a specific preset for your substrate.
●
Download a preset from the RIP vendor's website, or from the substrate vendor’s website.
●
Use a generic preset designed for your substrate category, even though it is not fine-tuned for the
specific substrate type. Bear in mind that generic substrate settings cannot be modified; instead, the
preset can be cloned and then modified.
●
Clone (copy) a preset for a similar substrate, and edit it as necessary.
●
Create a new preset, starting from scratch, using the Add new button.
If you can find a ready-made preset for your specific substrate, you are recommended to use it.
Online search
You can search online for a substrate preset by using the Online search function within the Substrate Library
front-panel menu. The printer connects to the HP Media Locator database on the Internet and allows you to
search all available substrate presets for your particular printer model, including HP and third-party
substrate brands. Hundreds of different substrate presets may be available, and the database of substrate
presets is continuously updated and expanded. You will always get the most up-to-date content in this way.
ENWWSubstrate presets71
When the printer is connected to the database (this may take a few seconds), a list of all available substrate
presets for your printer model is displayed. You can browse the list by scrolling it, and get details on any
preset by pressing its name. Besides browsing, there are two additional ways to look for presets: free-text
search and filters.
●
Free-text search allows you to type in any text using an on-screen virtual keyboard; all substrate
presets containing that text in any part of their name or description will be displayed. For example, if
you search for "vinyl" then substrate descriptions such as "self-adhesive vinyl" or "vinyl banner" will
match and be displayed. The search is case-insensitive; that is, "vinyl" will match both "vinyl" and
"Vinyl".
●
Filters are available for brand, type, sub-type, and application. When a value is selected for a given
filter, only the matching substrate presets will be displayed. For example, if you select "HP" from the
brand filter, only HP substrate presets will be displayed. The effect of using more than one filter is to
narrow the search to the combination of the filter settings. For example, if you choose "HP" from the
brand filter and "Self-Adhesive Vinyl" from the Type filter, only substrate presets for HP Self-Adhesive
Vinyl substrates are displayed.
Once you have located the substrate preset of your choice, pressing its download icon will queue it for
automatic download and installation in the background. You can select as many substrate presets as you
want for download and installation (they will be processed in the order that they were selected). You can
return to another part of the Media Manager or another front panel screen at any time after queuing presets
for download, and this will not interrupt the download and installation process.
Once a substrate preset has been downloaded in the background, it is checked and installed on the printer's
hard disk. During checking and installation, a full-screen message is shown on the front panel. This message
disappears when checking and installation is complete.
The new substrate preset now appears in the Substrate Library together with all previously installed and
factory-provided presets, and is ready for use.
Some supported RIPs may implement a similar online substrate-preset search function accessing the same
HP Media Locator database. Whether you use the printer's front panel search or RIP-based search does not
matter: the end result is the same. Supported RIP software synchronizes its substrate preset list with the
printer, so that printer and RIP will always have the same list.
72Chapter 4 Substrate settingsENWW
HP Media Locator
The HP Media Locator database of substrate presets can also be accessed from a Web browser by visiting
http://www.hp.com/go/mediasolutionslocator. This provides access to the database for different regions,
printer models, applications, suppliers, substrate types, and so on.
When you have located the substrate preset of your choice, you can download it to your computer. To install
the preset into the printer with which you want to use it, use the printer's Embedded Web Server. Navigate to
the Setup > Substrate presets management > Import screen.
Click Browse to browse to the substrate preset file that you have previously downloaded to your computer,
then click Update to install the preset in your printer.
The Embedded Web Server also allows you to export substrate presets from your printer for use with another
printer of the same model. When importing a previously exported substrate preset, you may see a message
warning you that the package is not signed (only packages downloaded from the HP Media Locator internet
database are digitally signed, as a form of authentication); you can then ignore the warning and continue
with the installation, or abort the installation.
Generic presets
Generic presets are each designed for a whole substrate category, rather than for a particular substrate type.
They cannot be edited, erased, saved, color-calibrated or ICC profiled; but they can be cloned. Therefore, if
you would like to modify a generic preset in any way, you should first clone it and then work on the clone,
which is fully editable.
The printer provides generic presets for the supported substrate categories: see Supported substrate
categories on page 38.
ENWWHP Media Locator73
Clone a substrate preset
You may wish to clone and edit a preset for various reasons:
●
To assign a name of your own choice to the preset
●
To adjust the preset to the precise characteristics of your substrate
●
To adjust the preset to your intended use of the substrate, which may range from highest-quality
printing to fast production output.
To clone a substrate preset, follow these steps:
1.Select a preset in the Substrate Library.
2.Click Clone to clone the preset, and enter a name for the new preset.
Modify a substrate preset
You can modify a preset by pressing Modify.
Then press beside the print mode that you want to modify; or click Add new print mode. You can delete
or change the name of any print mode; although you should keep at least one print mode.
NOTE:You can define up to six print modes.
74Chapter 4 Substrate settingsENWW
NOTE:The number of passes in an existing print mode cannot be changed. If you want to change the
number of passes, create a new print mode.
NOTE:You are not allowed to create two print modes with the same number of passes and the same color
saturation.
To change the values, you must print a test plot. Check it and choose the number in the pull-down colorsaturation menu that matches your preferences in terms of curing and drying. If none of the options are good
enough, try changing the temperature and reprint. You can also change the substrate advance settings.
Add a new substrate
If you cannot find a ready-made preset for your substrate, and prefer not to use a generic preset or edit an
existing preset, you can make your own preset from scratch.
The Add New Substrate wizard guides you to work out the best settings for your substrate. It first requests
some information about the substrate and your intended use of it, then prints some test prints and asks you
to evaluate them. From this information, it creates the new preset.
1.Ensure that the printer is in the Ready state.
2.Stop the job queue.
3.Load your new substrate, selecting the most similar substrate when asked to do so; or select None of
these.
4.When the substrate has been loaded, go to the Substrate Library on the front panel, and choose the
substrate category in the left column of the Substrate Library screen (PVC BANNER in this example),
then click + New PVC banner at the top of the right column. Your new preset will be based on a generic
preset; If there are multiple generic presets in that category, the front panel asks you to choose one of
them.
ENWWAdd a new substrate75
5.The following screen is displayed:
6.Press the blue button to produce the ink drying and color saturation test print; then continue adjusting
the settings and printing again until you are satisfied with the result.
NOTE:You can omit this step if you already know the settings that you want to use.
7.If you cannot reach a satisfactory result, you may want to press Advanced settings and try adjusting
those settings, which are intended for people who understand their implications.
To go back to the previous screen, press .
●
Straightness or bow compensation: Allows you to compensate for barrel-shaped substrate
deformation. The value represents the distance that the centre of the substrate has moved with
respect to the left and right edges. See The substrate has bow deformation on page 68.
●
Latex optimizer level: If you have bleed or coalescence, you can increase the optimizer level until
you see a significant impact on gloss or color saturation.
●
Vacuum printing: Sets the vacuum value in the print zone to hold the substrate flat. Increase if the
substratre suffers from crashes or smears, decrease if you see banding or graininess.
●
Advance factor: Allows you to increase or decrease the substrate advance in each carriage pass.
●
Inter-pass delay offset: The time delay between passes to allow for smoother drying. Increase the
delay if you have seen banding on your prints.
●
Input tension: Substrate rewinder tension, increase in case of wrinkled substrate in the print .zone
76Chapter 4 Substrate settingsENWW
8.When you have finished, press Continue to perform color calibration.
9.Enter your substrate name and click Start color calibration. See Color calibration on page 80.
10. After the automatic color calibration process has completed, we recommend using the generic ICC
profile; alternatively, you can choose to create a new profile or to copy a profile already assigned to a
different print mode for this substrate (if there are any such profiles). The Create ICC profile button is
disabled until color calibration is complete. See ICC profiles on page 82.
Change settings while printing
You can use the front panel to adjust the following settings while printing.
●
To change temperature, vacuum, inter-pass delay offset, and substrate-advance settings while
printing, press Adjustments in the front panel’s print job screen, and choose the setting that you want
to adjust. The changes that you make take effect immediately, but they are not saved: the next job will
use the settings in the substrate preset as usual.
You can use the Save button to save settings, and the Reset button to restore the last saved settings.
NOTE:The Save button is not available for a generic or non-editable preset.
●
To change substrate advance calibration while printing (in case of banding): press Adjustments >
Adjust substrate advance. The changes that you make take effect immediately, but they are not saved
for the next job. See also Substrate advance adjustment while printing on page 90.
ENWWAdd a new substrate77
To make permanent substrate-advance changes, use the RIP or front panel to modify the substrate
preset.
Temperature profile
Many of the main and advanced substrate settings are related to temperature control, since this is a critical
area for correct printing results with latex inks on a wide variety of substrates.
NOTE:There is a delay between making a change and seeing the results. See the front panel for actual
temperature checking.
NOTE:If you selected English units of measurement, you may notice some discrepancies, as the printer
works in Celsius and makes the conversion.
Select the number of passes
Increasing the number of passes will tend to improve the print quality but reduce the speed of printing.
NOTE:The following table is for the normal ink limit unless otherwise indicated.
NOTE:More specific settings for many substrates from different vendors are available in the HP Substrate
Finder at http://www.hp.com/go/latexmediafinder/.
NOTE:After selecting the number of passes in the Add New Print Mode screen, make sure to reset your
print mode to default category values for that print mode.
78Chapter 4 Substrate settingsENWW
Tips
●
2 to 4 passes provide lower print quality. Also, the color gamut will be slightly reduced, as total ink is
limited to allow for curing.
●
1200 dpi print resolution is available in the 18-pass print mode only. If you intend to use it, ensure that
you have a specific substrate preset for this print mode, because reusing others may not deliver the
expected print quality.
●
For fast layout proofing on low-cost substrates, a low-ink 2-pass print mode has been enabled. It is
recommended for paper-based substrates only, as curing may not work correctly for other substrate
types in this mode.
Delete a substrate preset
You can delete substrate presets that you have added yourself, but not those that were supplied with the
printer.
To do so, just press on the Substrate Library screen.
If you delete a preset, you will lose the reference to that substrate in the usage and accounting information.
Instead of the name of the substrate, from that moment on you will see “Deleted substrate” in the usage and
accounting information.
Faster printing
The obvious way to increase speed is to reduce the number of print passes, although this will tend to reduce
print quality. Bear in mind the following considerations:
●
With fewer than 8 passes, you may see an increase in grain.
●
With fewer than 6 passes, the printer is more sensitive to substrate-advance problems, and you may
need to reduce the ink quantity to improve print quality.
●
As you reduce the number of passes, the best curing temperature may be more difficult to find, and may
be more sensitive to the ambient temperature and humidity.
Here is another suggestion for increasing the speed of printing:
●
Concatenating prints saves time, because one can be printed while another is being cured.
NOTE:Printing a single job for more than 2 hours can reduce the life of the printheads.
See also The printer seems slow on page 135.
ENWWDelete a substrate preset79
Color calibration
The purpose of color calibration is to produce consistent colors with the specific printheads, inks, and
substrate that you are using, and in your particular environmental conditions. After color calibration, you can
expect to get very similar prints from your printer on different occasions.
Each substrate must be calibrated independently.
NOTE:Color calibration may not work correctly with non-HP ink.
There are cases in which a substrate may not be calibrated, in which cases the Calibrate and Reset options
are not available:
●
The loaded substrate has a generic preset.
●
The loaded substrate has a preset that is not editable.
●
The loaded substrate is not suitable for color calibration.
Color calibration can be launched from the front panel, after pressing Modify preset, or when adding a new
substrate.
In outline, the process consists of the following steps.
1.A calibration target is printed.
2.The colors on the calibration target are measured automatically.
3.The calibration target measurements are compared with an internal reference to calculate the
necessary calibration tables for consistent color printing on the substrate in use.
Factory default calibration tables are used whenever color calibration has never been run. The first time color
calibration is run, the current printing color is taken as a reference, and factory default calibration tables
continue to be used. This means that, after the first color calibration, the printed colors do not change, but
are recorded as the reference for future calibrations. Subsequent color calibrations compare calibration
target colors with the recorded reference, in order to calculate new calibration tables for consistent color
printing on that particular substrate type.
From the front panel, you can delete the current calibration table, leaving the factory default calibration
table active, as if that particular substrate had never been calibrated. Press , then Image quality
maintenance
Color calibration as described above is not recommended for the following substrate types. It may be
possible to calibrate some of these substrates by using an external color measurement device, driven by an
external RIP.
●
Non-opaque substrates such as clear film and backlit substrates.
●
Substrates with an uneven surface, such as perforated vinyl and punched-window substrates.
Substrates suitable for color calibration include even-surfaced adhesive vinyls (neither punched nor
perforated), PVC banners, and papers.
> Color calibration > Reset to factory.
Some substrates require the take-up reel for successful printing. However, the take-up reel may fail to cope
with the backward movement of the substrate between the printing and scanning phases of color calibration.
To perform color calibration when the take-up reel is in use, proceed as follows:
1.
Ensure that the take-up reel is enabled. At the front panel, press , then Enable take-up reel.
2.Set the take-up reel's winding direction to the off position. See Unload the take-up reel on page 61.
80Chapter 4 Substrate settingsENWW
3.Manually rewind the take-up reel, using the buttons on the take-up reel motor, to collect the substrate
and raise the tension bar until it almost touches the take-up reel.
4.Launch color calibration from the front panel.
5.When the color calibration has finished, you can reset the take-up reel’s winding direction.
Performing color calibration
The color calibration test chart is printed using a fixed print mode with a high number of passes and fixed
curing and drying settings to ensure printing consistency. However, parameters affecting substrate advance
should be fine-tuned, and printheads should be aligned, before starting color calibration for the first time.
To start color calibration of the loaded substrate from the front panel, select , then Image quality
maintenance > Color calibration > Calibrate. Color calibration can also be run while adding a new substrate
(see Add a new substrate on page 75).
NOTE:Only substrates at least 61 cm (24 in) wide can be calibrated.
The calibration process is fully automatic and can be performed unattended after you have loaded substrate
of the type you wish to calibrate. The process takes about 15 minutes and consists of the following steps:
1.The color calibration test chart is printed, which contains patches of different densities of each ink used
in your printer.
2.The test chart is scanned by the line sensor. If the scan cannot be completed successfully, a message is
displayed on the front panel; see Front-panel error codes on page 137.
3.From the measurements made by the line sensor, the printer calculates the necessary correction tables
to apply to your print jobs, for consistent color printing on that substrate type.
Calibration should be done in any of the following circumstances:
ENWWColor calibration81
●
Whenever a new substrate type is introduced that has not yet been calibrated.
●
Whenever you notice excessive color differences between prints. Such color differences are mainly
caused by aging and wear of the printheads, installing new printheads, and changes in substrate
characteristics between one roll and another.
You can check the color calibration status of your substrate by pressing on the front panel.
●
Recommended status indicates that this substrate has never been calibrated. In this case, the factorydefault color tables will be applied to print jobs, as there is no reference state defined. After one or
more color calibrations have been performed, pressing the Reset button returns the status to
Recommended.
●
Done status indicates that a color calibration has been performed successfully at least once on this
substrate, and therefore a color reference state is defined.
●
Obsolete status indicates that the last color calibration may be out of date. For instance, color
calibration status is set to Obsolete whenever a printhead is replaced. The color reference state remains
defined.
●
N/A indicates that this substrate cannot be color-calibrated.
NOTE:Generic substrates cannot be color-calibrated, although such substrates may be suitable for
color calibration. You can color-calibrate clones of most generic substrates.
TIP:If color calibration fails, it is worth trying again.
TIP:If the first color calibration of a new substrate fails, press the Reset button before trying again.
ICC profiles
Color calibration provides consistent colors, but consistent colors are not necessarily accurate. For instance,
if your printer prints all colors as black, its colors may be consistent but they are not accurate.
In order to print accurate colors, it is necessary to convert the color values in your files to the color values
that will produce the correct colors from your printer, your inks, your print mode, and your substrate. An ICC
profile is a description of a printer, ink, print mode, and substrate combination that contains all the
information needed for these color conversions.
These color conversions may be performed by your Raster Image Processor (RIP), if it offers that possibility;
they are not performed by the printer. For further information on the use of ICC profiles, see the
documentation for your application software and for your RIP.
In addition to the ICC profiles used for printing, you may wish to calibrate and profile your monitor (display
device), so that the colors you see on the screen relate more closely to those that you see on your prints.
82Chapter 4 Substrate settingsENWW
5Troubleshoot print-quality issues
●
General printing advice
●
Improve print quality
●
Most-common print-quality problems
ENWW83
General printing advice
Use the following approach when you have any print-quality problem:
●
Make sure that the substrate type that you select on the front panel, and in your RIP software, is the
same as the substrate type that is loaded in the printer. Make sure that the substrate type has been
calibrated (including substrate-advance, printhead, and color calibration).
CAUTION:If you have the wrong substrate type selected, you could experience poor print quality and
incorrect colors, and perhaps even damage to the printheads.
●
Make sure that you are using the correct substrate preset for your substrate, with the correct ICC
profile, or that you have followed the correct procedure to generate a new substrate preset (see Add a
new substrate on page 75).
●
Make sure that you are using appropriate print-quality settings in your RIP software.
●
Make sure that your environmental conditions (temperature, humidity) are in the recommended range.
See Environmental specifications on page 145.
●
Make sure that your ink cartridges have not passed their expiration dates. See Maintain the ink
cartridges on page 101.
●
Avoid touching the substrate while printing is in progress.
●
Trying to print jobs with a lot of ink in fast modes (commonly 6 passes or below) may result in notcompletely-dry output and/or other print-quality problems. Consider using modes with higher passes
when printing with a lot of ink, or increase the curing temperature. Note that increasing the curing
temperature may deform your substrate (see The substrate is deformed or wrinkled on page 67).
Improve print quality
As a first step, you may be able to improve print quality with a single command. At the front panel, press
, then Image-quality maintenance > Optimize print quality.
This performs printhead recovery, alignment, and color calibration routines, in order to optimize your print
quality automatically in a single step. Allow up to 30 minutes for the printer to perform the whole process.
If you still experience print-quality problems, you can follow a more hands-on print-quality troubleshooting
procedure, by printing, interpreting, and performing corrective actions.
You can print all the test plots at once for complete debugging of your print-quality problem. At the front
panel, press , then Image-quality maintenance > Print all test plots.
Alternatively, you can print the test plots individually for specific debugging of nozzle health, alignment,
optimizer, or substrate-advance print-quality issues as described below.
84Chapter 5 Troubleshoot print-quality issuesENWW
1. The printhead status plot
The printhead status plot consists of patterns that are designed to highlight printhead reliability problems. It
helps to determine whether any printhead is experiencing clogging or other problems.
To print this plot, go to the front panel and press , then Image-quality maintenance > Clean
printheads > Print test plot. Vinyl, preferably gloss at least 36 inches wide, is recommended for maximum
visibility. Other substrate types may not show enough detail to see the optimizer dashes clearly.
The plot consists of small dashes, one for each nozzle on each printhead.
For each individual colored pattern, make sure that most of the dashes are present.
Corrective action
1.Clean any faulty printheads. See Clean (recover) the printheads on page 105. Then reprint the
printhead status plot to see whether the problem has been solved.
2.If the problem persists, clean the printheads again, and reprint the printhead status plot to see whether
the problem has been solved.
3.If the problem continues to persist, replace any persistently faulty printheads. See Replace a printhead
on page 108.
2. The optimizer check plot
To print the optimizer check plot:
1.Use the same substrate type that you were using when you detected a problem.
2.Check that the selected substrate type is the same as the substrate type that is loaded into the printer.
3.
Go to the front panel and press , then Image-quality maintenance > Print latex optimizer test
plot.
The latex optimizer is a transparent fluid that may not be visible on all substrates; vinyl is recommended for
maximum visibility. This print consists of several area fills, text, lines and color bars. It is intended to identify
print-quality problems that may be caused by optimizer nozzle defects.
ENWWImprove print quality85
Compare the three rows.
●
The row with the symbol shows a simulated image with an above-normal amount of optimizer.
●
The row with the symbol shows a simulated image with a below-normal amount of optimizer,
equivalent to more than 200 blocked nozzles.
●
The row with the rectangle around it and the symbol shows the current performance of the printer,
printing 10 passes.
Look for differences in performance between the images, such as bleeding in the color bars, graininess in the
area fills, blurred text, and overall print quality.
If there is little difference in quality between the rows, there are at least two possible explanations:
●
The substrate is not sensitive to the amount of optimizer. There is probably no problem with the
optimizer printhead. Consider other explanations for whatever problem you have.
●
There may be a problem with the optimizer printhead if you see high levels of coalescence and bleed as
in the bad examples below. In this case, try to clean the optimizer printhead; see Clean (recover) the
printheads on page 105.
NOTE:The front panel shows an advisory message if abnormal optimizer performance has been
detected.
86Chapter 5 Troubleshoot print-quality issuesENWW
If there is a clear difference in quality between the rows, there are at least two possible explanations:
●
If the quality of the row with the symbol is higher, the substrate is very sensitive to the amount of
optimizer. Go to your substrate library on the front panel or in your RIP, select your print mode, and
increase the amount of optimizer in the the advanced settings. See Add a new substrate on page 75.
●
If you see no difference in quality between the rows with the and symbols, but the row with the
symbol looks worse, the substrate is sensitive to the amount of optimizer, but there seems to be no
problem with the optimizer printhead or the amount of optimizer used. Consider other explanations for
whatever problem you have.
3. The printhead alignment status plot
To print the printhead alignment status plot:
ENWWImprove print quality87
1.Use the same substrate type that you were using when you detected a problem. Or consider using vinyl
gloss substrate for better visibility of the optimizer in particular.
2.
Go to the front panel and press , then Image-quality maintenance > Align printheads > Print test
plot.
Check the continuity of the thin diagnostic lines on the alignment status plot. In one section, colored lines are
printed in line with black lines to test the alignment from one color to another. In a another section, colored
lines are printed such that one half is made with a forward pass and one half is made with a reverse pass to
test the alignment between the two directions. In both sets of patterns, printhead misalignment will be
visible as a step in the line at its center (marked with a short black line).
Bear in mind that small misalignments may not cause any print-quality defects. The printing process is
designed to hide the effects of small amounts of misalignment. The reference scale can be used to quantify
the amount of misalignment; errors below 4/600 inch are unlikely to cause print-quality defects.
The optimizer fluid is transparent and cannot usually be seen directly. The fluid can be seen on some
substrates (such as self-adhesive vinyl) when printed in conjunction with the colored inks. The cross pattern
that is printed above the reference scale is printed in this way and can be used to evaluate the alignment of
the optimizer on some substrates. In a well-aligned system, the light-colored cross at the center of the
pattern will be aligned with the four black lines at the sides of the pattern. The following figure shows how
this pattern will appear on the substrates on which it is visible. This sample is slightly misaligned.
88Chapter 5 Troubleshoot print-quality issuesENWW
If the printheads are misaligned or you feel unsure about them—for example, because a substrate crash
occurred—then align the printheads. See Align the printheads on page 106.
4. The substrate-advance check plot
To fine-tune the quality of your print, you may need to adjust the rate at which the substrate advances. The
substrate advance determines the placement of dots on the substrate. If the substrate is not advanced
correctly, light or dark bands appear in the printed image and the grain in the print may increase.
Substrate-advance adjustment is highly recommended, as the substrate advance is not automatically
monitored.
You can modify the substrate advance from the RIP or front panel with the Substrate Advance parameter in
the substrate preset.
To print the substrate-advance check plot:
1.Use the same substrate type that you were using when you detected a problem.
2.Check that the selected substrate type is the same as the substrate type that is loaded into the printer.
3.
Go to the front panel and press , then Image-quality maintenance > Substrate advance calib >
Print adjustment plot.
The substrate-advance check plot consists of several columns with a number at the bottom of each one.
Locate the lightest of the columns and enter its number into the Substrate Advance parameter for the
current substrate preset. The value chosen in this example should be “−6”.
NOTE:Minor substrate-advance problems (±2 around the 0 value) are unlikely to result in any print-quality
problem, especially with print modes of more than 8 passes.
ENWWImprove print quality89
Substrate advance adjustment while printing
If you are using no more than six passes, you can fine-tune the substrate advance while printing: press ,
Adjustments > Adjust substrate advance. Select a value of change from −10 mm/m to +10 mm/m (or
then
mils/inch). To correct light banding, decrease the value. To correct dark banding, increase the value.
If you are using eight passes or more, a wrong advance adjustment will not produce banding but graininess,
which is harder to assess visually. Therefore, in this case you are recommended to use only the adjustment
plot.
When you have chosen a value and pressed OK, the rest of your job will be printed with that value, but it will
be reset to zero at the end of the job. Add the value found to the Substrate Advance value in the preset to
print all future jobs with the new setting.
What to do if problems persist
If you still experience print-quality problems after applying the advice in this chapter, here are some
additional tips to consider:
●
Try selecting a higher print-quality option in your RIP software, by increasing the number of passes.
●
Check that your printer firmware is up to date. See Firmware update on page 129.
●
Check that you have the correct settings in your software program.
●
Call your service representative. See When you need help on page 34.
Most-common print-quality problems
Graininess
If you see this kind of problem:
●
Ensure that the vertical correction option is disabled in the RIP and in the front panel. At the front panel,
press , then Image-quality maintenance > Vertical correction (if this option is available).
●
The printheads may be misaligned. This is likely if you have not aligned the printheads for a long time,
or if there has been a substrate jam. Align the printheads if necessary (see Align the printheads
on page 106). You can check whether it is necessary by using the printhead alignment status plot (see
3. The printhead alignment status plot on page 87).
●
If you are printing with eight or more passes, the substrate advance may need proper calibration. See 4.
The substrate-advance check plot on page 89.
90Chapter 5 Troubleshoot print-quality issuesENWW
●
Use a higher number of passes: you will probably see less grain with ten or more passes.
●
If graininess is more visible in light area fills, with the appearance of coalescence graininess (see 2. The
optimizer check plot on page 85), try the following solutions:
◦
Go to your substrate library on the front panel or in your RIP. Select your print mode and increase
the amount of optimizer in the the advanced settings. See Add a new substrate on page 75.
◦
Clean the optimizer printhead.
◦
Print in Economode (four colours).
NOTE:A small change in overall graininess (but not coalescence) may be perceived in some
areas because the light-colored inks, which are not used in Economode, help to provide smooth
transitions.
Horizontal banding
Try the following remedies if your printed image suffers from added horizontal lines as shown (the color may
vary).
●
If you are using a print mode with six or fewer passes, try increasing the number of passes. Some
degree of banding can be expected with few passes.
●
If bands affect all colors across the width of the printed image, the cause is probably a substrate
advance problem. Use the front panel to adjust the substrate advance on the fly (see Substrate advance
adjustment while printing on page 90). If you have dark bands, increase the substrate advance; if you
have light bands, decrease it. When you find the right adjustment, store the value in the front panel for
future prints on the same substrate.
Another cause could be a fiber attached to one of the printheads. Turn off the printer, then remove the
printheads one at a time and remove any fibers that you see attached to them.
●
If bands affect only some colors, the cause could be a defective printhead.
◦
Print the printhead status plot (see 1. The printhead status plot on page 85). If necessary, clean
the printheads (see Clean (recover) the printheads on page 105).
◦
Sometimes a single cleaning action may not completely clean every nozzle. Print the status plot
and consider cleaning again.
◦
Align the printheads (see Align the printheads on page 106). If necessary, align them manually.
◦
Print the printhead status plot again. Identify the printhead with the greatest number of blocked
nozzles, and replace it.
NOTE:The optimizer printhead is unlikely to cause this kind of problem.
ENWWMost-common print-quality problems91
●
If bands affect most of the colors, the printheads could be misaligned. This is likely if you have not
aligned the printheads for a long time, or if there has been a substrate jam. Align the printheads if
necessary (see Align the printheads on page 106). You can check whether it is necessary by printing the
printhead alignment status plot (see 3. The printhead alignment status plot on page 87).
●
If banding occurs mostly in black areas, create a new color profile using pure black and not a mixture of
other colors. See your RIP documentation.
●
Due to the printhead servicing routines while printing, some fibers or small amounts of ink may be
deposited on a nozzle, causing it to fail temporarily. This is very unlikely and may just cause a couple of
isolated bands. It is also very unlikely for this to be repeated within the same or subsequent print jobs.
However, if you notice it, try cleaning the printheads (see
If the problem persists, call your service representative (see When you need help on page 34).
Vertical banding
Different kinds of vertical bands may appear, for different reasons.
●
Regular vertical bands matching the shape of the platen may be seen on paper-based substrates and in
general on thin substrates in medium-density area fills such as grays or violets. Try the following
suggestions to mitigate this problem:
◦
Align the printheads. See Align the printheads on page 106.
◦
Try the automatic correction for vertical banding. At the front panel, press , then Image-
Clean (recover) the printheads on page 105).
quality maintenance
NOTE:Remember to disable the vertical banding correction when you no longer need it, because
it may increase grain.
◦
Reduce the vacuum level in steps of 5 mmH2O when printing on vinyl. Do not exceed the lower
limit of 10 mmH2O for vinyls or 25 mmH2O for papers to avoid crashes and/or smears. Consider
using the substrate edge holders to avoid lateral crashes. See The edge holders on page 51.
◦
Consider using the take-up reel, for better control of the substrate.
◦
This kind of banding is less visible when the printer is stable at high temperature (after more than
half an hour of continuous printing). You can help to avoid visible banding by modifying the
printing queue so that vulnerable or important prints are printed later; or by pre-warming the
printer by using the option available in your RIP.
●
Thin vertical dark bands, typically seen in the first 150–200 mm of the print in high-density area fills or
in backlit applications
◦
Reduce the ink quantity if possible.
◦
When using backlit and synthetic substrates, decrease the vacuum level to values around 5–15,
depending on the substrate thickness. More vacuum is normally applied to thick substrates and
less to thin substrates.
◦
Increase the number of passes.
> Vertical correction. This option should also be available in your RIP.
◦
If applicable, use the RIP to group jobs together, so that printer temperatures remain more stable
between jobs.
●
Irregular or isolated vertical bands with abnormal levels of graininess
92Chapter 5 Troubleshoot print-quality issuesENWW
◦
Increase the vacuum level in steps of 5 mmH2O. Do not exceed the following limits: 20 mmH2O for
banners, 45 mmH2O for vinyl, and 50 mmH2O for other substrate families.
◦
In backlit applications, increase the number of passes to 20, maintaining the vacuum level below
20 mmH2O.
◦
If the banding appears only at the beginning of the print, advance the substrate manually about
100–150 mm before the first print.
The print is deformed into a curved shape
This may occur as a result of substrate bow deformation. See The substrate has bow deformation
on page 68.
Misaligned colors
If the colors are misaligned in any direction, the printheads may be misaligned. This is likely if you have not
aligned the printheads for a long time, or if there has been a substrate jam. Align the printheads if necessary
(see Align the printheads on page 106). You can check whether it is necessary by printing the printhead
alignment status plot (see 3. The printhead alignment status plot on page 87).
Color variation and text-line correction
If some printhead nozzles are in use while others in the same printhead are not, water evaporates slowly
from the ink in the unused nozzles, making the color more intense. Thus, in such cases you may notice
variations in color intensity in areas where the color of the image should be constant.
If you notice such a problem, there are various possible solutions.
1.If you notice the variation in intensity near one side of the print, try rotating the image by 180 degrees
before printing. This may solve the problem in some cases, as all the nozzles are refreshed whenever
they enter the service station between passes.
ENWWMost-common print-quality problems93
2.Use your RIP to add lateral color bars on the side of the plot that is close to the ink supplies. The color
bars are designed to exercise all the printhead nozzles, to prevent the problem from occurring.
NOTE:Not all RIPs provide this option.
3.Add lateral color bars to the image, manually, before printing. In this case, you can either use the
standard colors, or decide to include a particular color in which you have noticed the problem. The
recommended width of each color bar is 3 mm.
4.
At the front panel, press , then Image-quality maintenance > Color variation and text-line
correction > On.
If text, lines, or light solid areas are rough or blurred, try the following suggestions:
●
The printheads may be misaligned.This is likely if you have not aligned the printheads for a long time, or
if there has been a substrate jam. Print the printhead alignment status plot (see 3. The printhead
alignment status plot on page 87), and align the printheads if necessary (see Align the printheads
on page 106).
●
The optimizer printhead may have blocked nozzles. You can check this by printing the optimizer check
plot (see 2. The optimizer check plot on page 85).
●
Water evaporates slowly from the ink in the unused nozzles, so the first drops of ink are ejected with
lower velocity. This may happen, for example, in nozzles not used during a whole printed swath,
causing the text or lines to be rough or blurred. You are recommended to go through steps 1 to 4 as
described above.
●
If a light area is close to the edge while printing on a thin substrate, ensure that the substrate is loaded
with the substrate edge on a rib of the platen to avoid local blurring. Alternatively, try rotating the
image so that the affected area is not at the edge of the substrate.
Black areas look hazy
If black areas look hazy or not sufficiently black, try these suggestions.
●
Increase the number of passes.
●
Laminate the print.
●
Substrate presets are designed to achieve consistent and reliable print quality on a broad range of
substrates. However, you may want to consider investing in the color management process, using
external tools and/or experts, to get specific results. The best dark colors on gloss vinyls and other
substrates are normally obtained when using as much black and as little composite as possible when
creating the ICC profile.
94Chapter 5 Troubleshoot print-quality issuesENWW
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.