
1-174
H
Dome Packages
The HLMP-6XXX Series dome
lamps for use as indicators use
a tinted, diffused lens to provide
a wide viewing angle with a
high on-off contrast ratio. High
brightness lamps use an
untinted, nondiffused lens to
provide a high luminous
intensity within a narrow
radiation pattern.
Arrays
The HLMP-66XX Series
subminiature lamp arrays are
available in lengths of 3 to 8
elements per array. The
luminous intensity is matched
within an array to assure a 2.1
to 1.0 ratio.
Resistor Lamps
The HLMP-6XXX Series 5 volt
subminiature lamps with built
in current limiting resistors are
for use in applications where
space is at a premium.
Lead Configurations
All of these devices are made by
encapsulating LED chips on
axial lead frames to form molded
epoxy subminiature lamp
packages. A variety of package
configuration options is available. These include special
Features
• Subminiature Flat Top
Package
Ideal for Backlighting and
Light Piping Applications
• Subminiature Dome
Package
Diffused Dome for Wide
Viewing Angle
Nondiffused Dome for High
Brightness
• Arrays
• TTL and LSTTL
Compatible 5 Volt Resistor
Lamps
• Available in Six Colors
• Ideal for Space Limited
Applications
• Axial Leads
• Available with Lead
Configurations for Surface
Mount and Through Hole
PC Board Mounting
Description
Flat Top Package
The HLMP-PXXX Series flat top
lamps use an untinted, nondiffused, truncated lens to
provide a wide radiation pattern
that is necessary for use in
backlighting applications. The
flat top lamps are also ideal for
use as emitters in light pipe
applications.
Subminiature LED Lamps
Technical Data
surface mount lead configurations, gull wing, yoke lead or Zbend. Right angle lead bends at
2.54 mm (0.100 inch) and
5.08 mm (0.200 inch) center
spacing are available for
through hole mounting. For
more information refer to
Standard SMT and Through
Hole Lead Bend Options for
Subminiature LED Lamps data
sheet.
HLMP-PXXX Series
HLMP-QXXX Series
HLMP-6XXX Series
HLMP-70XX Series
5964-9350E

1-175
DH AS High High Device
Standard AlGaAs Efficiency Perf. Emerald Outline
Red Red Red Orange Yellow Green Green Device Description
[1]
Drawing
P105 P205 P405 P305 P505 P605 Untinted, Nondiffused, A
Flat Top
P102 P202 P402 P302 P502 Untinted, Diffused, B
Flat Top
6000/6001 Q101 6300 Q400 6400 6500 Q600 Tinted, Diffused
Q105 6305 6405 6505 Untinted, Nondiffused,
High Brightness
Q150 7000 7019 7040 Tinted, Diffused, Low B
Current
Q155 Nondiffused, Low
Current
6600 6700 6800 Tinted, Diffused,
Resistor, 5 V, 10 mA
6620 6720 6820 Diffused, Resistor, 5 V,
4 mA
6203 6653 6753 6853 3 Element Matched
6204 6654 6754 6854 4 Element
6205 6655 6755 6855 5 Element C
6206 6656 6756 6856 6 Element
6208 6658 6758 6858 8 Element
Device Selection Guide
Part Number: HLMP-XXXX
Package Dimensions
(A) Flat Top Lamps
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
*Refer to Figure 1 for design concerns.
Array,
Tinted,
Diffused

1-176
Package Dimensions (cont.)
(B) Diffused and Nondiffused
Figure 1. Proper Right Angle Mounting to a PC Board to Prevent Protruding Cathode Tab from Shorting to Anode
Connection.
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
*Refer to Figure 1 for design concerns.
(C) Arrays
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.

1-177
DH AS High High
Standard AlGaAs Eff. Perf. Emerald
Parameter Red Red Red Orange Yellow Green Green Units
DC Forward Current
[1]
50 30 30 30 20 30 30 mA
Peak Forward Current
[2]
1000 300 90 90 60 90 90 mA
DC Forward Voltage 6 6 6 6 V
(Resistor Lamps Only)
Reverse Voltage (I
R
= 100 µA)5 555555V
Transient Forward Current
[3]
2000 500 500 500 500 500 500 mA
(10 µs Pulse)
Operating Temperature Range: -55 to -40 to -55 to +100 -40 to -20 to
Non-Resistor Lamps +100 +100 +100 +100
°C
Resistor Lamps -40 to +85 -20 to
+85
Storage Temperature Range °C
For Thru Hole Devices 260°C for 5 Seconds
Wave Soldering Temperature
[1.6 mm (0.063 in.) from body]
For Surface Mount Devices:
Convective IR 235°C for 90 Seconds
Vapor Phase 215°C for 3 Minutes
Absolute Maximum Ratings at T
A
= 25°C
-55 to +100
Notes:
1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps.
2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions.
3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not
operate these lamps at this high current.

1-178
Electrical/Optical Characteristics, T
A
= 25°C
Standard Red
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
6000 0.5 1.2
6001 Luminous Intensity
[1]
I
v
1.3 3.2 mcd IF = 10 mA
6203 to 0.5 1.2
6208
Forward Voltage V
F
1.4 1.6 2.0 V IF = 10 mA
All Reverse Breakdown V
R
5.0 12.0 V IR = 100 µA
Voltage
P005 Included Angle Between 125
Half Intensity Points
[2]
2θ1/2 Deg.
All 90
Others
Peak Wavelength λ
PEAK
655 nm
Dominant Wavelength
[3]
λ
d
640 nm
Spectral Line Half Width ∆λ
1/2
24 nm
All Speed of Response τ
s
15 ns
Capacitance C 100 pF VF = 0; f = 1 MHz
Thermal Resistance Rθ
J-PIN
170 °C/W Junction-to-Cathode
Lead
Luminous Efficacy
[4]
η
v
65 lm/W