HP D2830A
HP D2831A
HP Ergo 1024
15-inch Color Displays
13.9 inch Viewable Image
User’s Guide
15-Zoll-Farbbildschirme
13.9 Zoll Bildanzeige
Benutzerhandbuch
Moniteurs couleur 15 pouces
Affichage 13,9 pouces
Guide de l’utilisateur
Pantallas de color de 15 pulgadas
13.9 pulgadas de imagen visualizada
Manual del Usuario Léase esto primero
Video a colori da 15 pollici
13.9 effetivi per l’immagine
Manuale utente
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the impl ied warranties of
merchantability and fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HewlettPackard.
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document
may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company.
Hinweis
Inhaltliche Änderungen vorbehalten.
Hewlett-Packard übernimmt keine Garantie welcher Art auch immer für diese Ausrüstung, einschließlich der (doch nicht begrenzt
auf die) Qualitätsgarantie und die Garantie bezüglich Eignung für einen bestimmten Zweck.
Hewlett-Packard haftet nicht für in dieser Dokumentation enthaltene Fehler oder für unbeabsichtigte oder indirekte Schäden in
Verbindung mit der Lieferung, der Leistung oder der Benutzung der Ausrüstung.
Hewlett-Packard übernimmt keine Haftung fur den Betrieb oder die Zuverlässigkeit seiner Software, wenn diese auf Hardware
benutzt wird, die nicht von Hewlett-Packard geliefert wurde.
Dieses Dokument enthalt proprietäre Informationen, die durch das Copyright geschützt sind. Alle Rechte vorbehalten. Dieses
Dokument darf ohne vorherige schriftliche Genehmigung der Hewlett-Packard Company weder ganz noch teilweise fotokopiert,
reproduziert oder übersetzt werden.
Avertissement
Les informations contenues dans ce document peuvent être modifiées sans préavis.
Hewlett-Packard ne donne aucune garantie de quelque sorte que ce soit concernant, sans que ce soit limitatif, les garanties
implicites de qualité commerciale de ce matériel, ou la bonne adaptation de celui-ci à un usage particulier.
Hewlett-Packard n’est pas responsable des erreurs pouvant apparaître dans ce manuel et n’est pas non plus responsable des
dommages directs ou indirects résultant de l’équipement, des performances et de l’utilisation de ce matériel.
Hewlett-Packard ne saurait être tenu pour responsable de l’utilisation et de la fiabilité de son logiciel sur des matériels non fournis
par Hewlett-Packard.
Les informations contenues dans ce document sont originales et protégées par copyright. Tous droits réservés. L’acheteur s’interdit
en conséquence de les photocopier, de les reproduire ou de les traduire dans toute autre langue, sauf accord préalable et écrit de
Hewlett-Packard.
Aviso
La información contenida en este documento está sujeta a cambios sin previo aviso.
Hewlett-Packard no ofrece ningún tipo de garantía con respecto a este material, incluyendo, pero sin limitarse a, las garantías
implícitas de comerciabilidad e idoneidad para un fin determinado.
Hewlett-Packard no asume responsabilidad alguna por los posibles errores contenidos o por los daños casuales o emergentes
relacionados con el suministro, funcionamiento o uso de este material.
Hewlett-Packard no asume responsabilidad alguna por el uso o fiabilidad de su software en equipos que no hayan sido fabricados
por Hewlett-Packard.
Este documento contiene información patentada, protegida por las leyes del copyright. Reservados todos los derechos. Ninguna
parte de este documento puede ser fotocopiada, reproducida o traducida a otro idioma sin la autorización previa y por escrito de
Hewlett-Packard Company.
Avviso
Le informazioni contenute in questo documento sono soggette a cambiamento senza preavviso.
Hewlett-Packard non rilascia garanzie di alcun tipo riguardo a questo materiale, comprese le garanzie implicite di commerciabilità
e di idoneità per uno scopo particolare.
Hewlett-Packard non sarà ritenuta responsabile per errori contenuti in questo documento, né per danni accidentali o conseguenti
alla fornitura, alle prestazioni o all’uso di questo materiale.
Hewlett-Packard non si assume alcuna responsabilità riguardo all’uso o all’affidabilità del proprio software su apparecchiature di
altri produttori.
Questo documento contiene informazioni di proprietà protette da copyright. Tutti i diritti sono riservati. Nessuna parte di questo
documento può essere fotocopiata, riprodotta o tradotta in un’altra lingua senza un precedente consenso scritto di Hewlett-Packard
Company.
Hewlett-Packard France
Commercial Desktop Computing Division
38053 Grenoble Cedex 9
France
© 1997 Hewlett-Packard Company
Francais
1
Full scan screen that gives an
edge to edge image
0.28 mm dot pitch for excellent graphics
Anti-glare , multilayer
anti-static screen coating
On/Off switch
Display adjustment buttons
HP D2830A, HP D2831A
15-inch Color Displays
13.9-inch Viewable Image
User’s Guide
Light indicator
HP Ergo 1024 User’s Guide
Important Safety Instructions
Important Safety Instructions
Before you plug in your new display, read these important safety
instructions.
WARNING
Connect the display only to a grounded power outlet. Use the power
cord supplied with the display or one with a properly grounded plug.
Ensure the cable meets your country’s standards for safety.
To avoid the risk of an electric shock, do not open the cover of the
display. There are no user-serviceable parts inside. To completely
disconnect power at the display, remove the power cord from the
power outlet. Ensure that the power outlet is easily accessible.
The display is quite heavy (the weight is shown in the technical
specifications). We recommend you ask the assistance of a second
person when lifting or moving it.
USA and Canada
If the power cord is not supplied with your display, select the proper
power cord according to the appropriate national electric codes.
USA: use a UL Listed Type SVT or Type SJT detachable power cord.
•
Canada: use a CSA certified detachable power cord.
•
Si le cordon secteur n’est pas livré avec votre moniteur, utiliser un
cordon secteur en accord avec le code national électrique applicable.
USA: utiliser un cordon secteur UL Liste de type SVT ou SJT.
•
Canada: utiliser un cordon secteur certifié CSA.
•
2 English
HP Ergo 1024 User’s Guide
What Your New Display Offers
What Your New Display Offers
The HP Ergo 1024 Display is a 15-inch (13.9-inch viewable image), high
resolution, multi-synchronous color display. Multi-synchronous means that
the display supports a range of video modes. It can be used with
Hewlett-Packard personal computers (or equivalent) equipped with an HP
Ultra VGA video solution (or equivalent).
Your HP D2830A / D2831A color display has the following features:
• A 15-inch flat square tube, with a 13.9-inch viewable image, and
0.28 mm dot pitch for excellent graphics. Multilayer, anti-glare coating to
minimize reflection.
• Support of video modes up to Ergo Ultra VGA 1024 at high ergonomic
refresh rates, and Ultra VGA 1280 at 60 Hz.
• Image adjustment using on-screen menus. Includes color adjustment and
image rotation controls to optimize the quality and position of the image.
• Display power management system (VESA
suitably equipped HP Vectra PCs to automatically reduce the power
consumption of the display. Complies with the Energy Star Computers
Program initiated by the US EPA
2
, and with the Swedish NUTEK3
specification for energy efficient displays.
• Display Plug and Play capability (VESA DDC1/2B standard) that enables
the display to identify itself to suitably equipped HP Vectra PCs.
• Compliance with ISO 9241-3 and ISO 9241-8 ergonomic standards.
• Your HP D2830A complies with MPRII guidelines for electric and magnetic
field emission issued by SWEDAC
4
.
• Your HP D2831A complies with the Swedish standard SS4361490, Level A,
(MPR III) for electric and magnetic field emission.
• Your HP D2831A complies with the TCO
electrical and magnetic fields, and for energy saving. It also complies with TCO
‘95 requirements which include environmental specifications.
1
standard) controlled from
5
‘92 requirements for low frequency
1. VESA is the Video Electronics Standards Association
2. The US EPA is the United States Environmental Protection Agency
3. NUTEK is the Swedish National Board for Industrial and Technical Development
4. Swedish Board for Accreditation and Conformity Assessment
5. Swedish Confederation of Professional Employees
English 3
HP Ergo 1024 User’s Guide
Setting Up Your Display
Setting Up Your Display
Where to Place the Display
Place your display on a flat sturdy surface.
Ensure the operating site is free from excessive heat, moisture, and sources of
electromagnetic fields. Sources of electromagnetic fields include
transformers, motors, and other displays.
Connecting the Cables
Before you connect any cables, refer to the safety instructions at the
beginning of this manual and make sure your PC and display are switched off.
Connect the video cable (it has a 15-pin plug) to the video outlet on
1
your PC and to the display. Tighten the thumbscrews on the plug.
Connect the power cord to the display.
2
NOTE
Plug the power cord into the power outlet.
3
1
Video cable
(15-pin plug)
2
3
Powe r cord
The location of your PC’s video outlet may be different to the one shown
in the diagram. Refer to the manual that came with your PC, if
necessary.
4 English
Using the Display
There are 7 buttons on the front of the display.
HP Ergo 1024 User’s Guide
Using the Display
1
The uses of these buttons are as summarized in the following table:
Button Use
On/Off switch
The and buttons can be used to adjust the Contrast directly
The and buttons can be used to adjust the Brightness directly
1
2
1: To choose between items in the main menu and sub menus
The chart on the next page summarizes the sequences of button-presses that
are needed in order to make adjustments to the display settings.
1: To make the main menu appear on the screen
2: To select the highlighted menu item (and sub-menu item if there is one)
1: To return to the main menu, having completed an adjustment
2: To quit the control menu
2: To make adjustments to the selected menu item
2
English 5
HP Ergo 1024 User’s Guide
Using the Display
or
or
1
Contrast
Brightness
Main menu
or
Brightness
Position
Size
Advanced
Geometry
Expanded View
Pincushion / Trapezoid
Parallel / Rotation
or
Pinbalance / V-Linear
Clear Moire
To make the main menu appear press
To quit it, press
To select a menu item press
To quit it, press
2
1
2
6 English
Color
Color Temperature
Controls
Color Control
Recall
Degauss
User Setup
Language
Menu Position
1
or
Menu Display Time
User Mode
HP Ergo 1024 User’s Guide
Using the Display
ADVANCED
GEOMETRY
Type of distortion Description Use This Correction
or The vertical edges of the image bow in or bow out Pin-cushion
or The vertical edges of the image slope in or slope out Trapezoid
or The vertical edges of the image slope left or slope right Parallelogram
or The vertical edges of the image bow left or bow right Pin-balance
or The whole image is askew on the screen Rotation
or The image appears compressed towards the top or the bottom V-Linear
An interference effect, often most visible when the screen
The standard view is guaranteed to meet the technical specifications of the
display. The expanded view magnifies the details of the image, but the
shape of the viewable area might need adjusting.
If image appears distorted, or misaligned, there are a number of adjustments
that can be performed. These are summarized in the following table.
Clear Moire
background is set to a pattern of dots.
(changing the background pattern
and color can also reduce moire)
COLOR CONTROLS
RECALL
DEGAUSS
To change the warmth of the displayed image, select the Color
Temperature sub-menu. Choosing 6550 K gives a white which is close to
average daylight, choosing 9300 K gives a white with a noticeable bluish tinge.
To revert to the factory default settings, select Recall from the main menu.
Use the button to select “yes” (revert to the default settings), and the
button to select “no” (revert back to the most recent settings).
Degaussing removes color impurity caused by magnetic fields. You should
degauss your display every few days.
Degaussing starts as soon as you press the button, to select Degauss
from the main menu, and is accompanied by brief instability of the displayed
image and a brief humming sound.
1
English 7
HP Ergo 1024 User’s Guide
Using the Display
USER SETUP
The
User Mode
sub-menu enables you to obtain information on the
factory settings, the user settings, and the one that is currently in use.
This information can be viewed, but not changed. The factory settings
store the display’s standard configurations; the user settings record any
adjustments that the user makes in the main menu system. There are 20
settings (factory settings plus user settings) in total.
Setting the Amount of Displayed Information and Minimizing Eye
Strain
To change the amount of displayed information, set the
your PC. The higher the screen resolution, the more information you can see
on the screen. To change the screen resolution, please refer to the manual that
came with your PC or your operating system documentation.
To avoid screen flicker and minimize eye strain, use the highest supported
image refresh rate
number of times the image is updated per second.
It is recommended that you use a resolution of 1024×768 at refresh rate of
85 Hz, or else 800×600 at 85 Hz. This gives easy-to- read characters, a large
amount of displayed information, and a flicker-free image.
Your display has Plug and Play capability (to the VESA DDC1/2B+ standard),
enabling it to identify itself to suitably equipped HP Vectra PCs. This will
automatically give you the best refresh rate for the resolution that you have
set.
for the chosen resolution. The image refresh rate is the
screen resolution
of
Minimizing Energy Consumption
If your PC supports VESA display power management (available on many HP
Vectra PCs), you can minimize the power consumed by the display. There are
two power saving modes:
Mode Power Consumption Indicator Light Horizontal Sync Vertical Sync Video Signal
Normal 80 W (max) green active active active
Stand-by < 15 W amber/green blinking active inactive blanked
Sleep < 5 W amber blinking inactive inactive blanked
To set these power saving modes, refer to the manual that came with your PC.
If your screen is not displaying an image, check the front panel indicator light
first — your display may be in a power saving mode.
8 English
PICTURE TUBE
INPUT SIGNAL
INTERFACE
HP Ergo 1024 User’s Guide
Technical Specifications
Technical Specifications
Size 15-inch flat screen / 13.9-inch viewable image
Phosphorous Red, Green, Blue medium short persistence
Dot pitch 0.28 mm dot pitch
Face Plate Anti-glare, multilayer, anti-static coating
Video 0.66 Vp-p analog RGB
Synchronization Separated H/V (TTL level), H/V mixed (TTL level)
Input Connectors 15-pin mini D-SUB
SCANNING FREQUENCY
MAX. RESOLUTION (H
WARM-UP TIME
PIXEL CLOCK
IMAGE SIZE
POWER SOURCE
OPERATING ENVIRONMENT
CABINET DIMENSIONS
WEIGHT
TILT/SWIVEL STAND
×
Horizontal 30 to 69 kHz
Vertical 50 to 160 Hz
1280 ×1024 at 60 Hz refresh rate
V)
30 minutes to reach optimum performance level
110 MHz Maximum
Standard size
Maximum size: 282.5 (H) × 212 (V) mm
AC 90 to 264 V, 47 to 63 Hz, 80 W (max), less than 15 W in stand-by mode, less than 5 W in sleep mode
Temperature 0 °C to 40 °C (operating)
Humidity 10% RH through 80% (without condensation) (operating)
387 (H) × 376 (W) × 427 (D) mm
13.6 kg
Tilt Angle - 5° to +10
Swivel Angle
1
: 267 (H) × 200 (V) mm (resolution at 1024 × 768, aspect ratio 4:3)
250 (H) × 200 (V) mm (resolution at 1280 × 1024, aspect ratio 5:4)
1. Use the standard image sizes to avoid distortion of the displayed image.
- 20 °C to +70 °C (storage)
5% RH through 95% (without condensation) (storage)
°
±45°
English 9
HP Ergo 1024 User’s Guide
Technical Specifications
Supported Video Modes
Your display supports the video modes shown in the table below.
Screen Resolution Image Refresh Rate Video Solution
CAUTION
640 × 480
640 × 480
640 × 480
800 × 600
800 × 600
1024 × 768
1024 × 768
1280 × 1024
Selecting a screen resolution/vertical frequency combination higher than
1280 × 1024 at 60 Hz can damage your display.
60 Hz VGA
75 Hz Ergonomic VGA
85 Hz Ergonomic VGA
75 Hz Ergonomic Super VGA
85 Hz Ergonomic Super VGA
75 Hz Ergonomic Ultra VGA 1024
85 Hz Ergonomic Ultra VGA 1024
60 Hz Ultra VGA 1280
10 English
HP Ergo 1024 User’s Guide
Care and Cleaning
Care and Cleaning
Do not place anything on top of the display. Doing so may block the display
vents and cause damage to the display due to overheating.
Do not let liquid get on or into the display.
To maximize screen life and prevent damage to the picture tube (such as
etching due to leaving the same image on the screen for a long time), it is
recommended that you:
• Use the display power management system (on HP Vectra PCs) and a
screen saver program.
• Avoid setting contrast and brightness to their maximum levels for
prolonged periods.
• Degauss at least every few days to remove any color impurities. Degaussing
is accompanied by brief instability of the displayed image and a brief
humming sound.
• Switch the display off, or reduce brightness and contrast to minimum levels,
when the display is not in use and if you do not have a power management
system or a screen saver program.
Your display has an anti-static screen coating. To prevent damage to the
display screen’s coating, use a regular household glass cleaner when cleaning
the screen. To clean the screen:
Switch the display off and remove the power plug (pull the plug, not the
1
cable).
Wet a soft cotton cloth with the cleaning solution and gently wipe the
2
screen. Do not spray cleaner onto the screen because the cleaner may drip
inside the display.
Dry with a clean, soft cotton cloth.
3
Do not use cleaning solutions containing fluoride, acids, or alkalis. The screen
coating can become scratched, or otherwise damaged, through the use of
sharp objects.
English 11
HP Ergo 1024 User’s Guide
Hardware Warranty
Hardware Warranty
This is your HP Display Hardware Warranty Statement. Warranty terms may be
different in your country. If so, your Authorized HP Dealer or Hewlett-Packard Sales
and Service Office can give you details.
Limited Display Hardware Warranty
Model Warranty Period Service provided
Model D2830A, D2831A 3 years: unless original end-user
customer has otherwise agreed to
a shorter period of warranty at
the time of purchase.
On-site service for first year, and
return to an HP or
repair-authorized reseller
service-center for the following
two years.
Hewlett-Packard (HP) warrants this display hardware product against defects in
materials and workmanship for the applicable warranty period stated above,
commencing from the date of purchase by you, the original end-user customer. If you
return this display hardware product with a defect as defined above, during the
warranty period, to an HP-authorized reseller or service center, HP will either, at its
option, repair or replace the defective product with a new or equivalent-to-new unit of
the same or equivalent model. Should HP be unable to repair or replace the product
within a reasonable amount of time, your alternate exclusive remedy shall be a refund
of the purchase price upon return of the product.
If you purchased this display hardware product for use with an HP Vectra personal
computer, please refer to the terms and conditions of the HP Hardware Warranty
statement provided with your HP Vectra personal computer, including limitations, your
responsibilities and method for obtaining warranty service.
Limitation of Warranty
The above warranty shall not apply to defects resulting from: misuse (including
"burned" screens); unauthorized modification; operation or storage outside the
environmental specifications for this display product; in-transit damage; improper
maintenance; or defects resulting from use of non-HP software, accessories, media,
supplies, consumables, or such items not designed for use with this product.
HP MAKES NO OTHER EXPRESS WARRANTY, WHETHER WRITTEN OR ORAL,
WITH RESPECT TO THIS PRODUCT. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO
THE DURATION OF THE EXPRESS WARRANTY SET FORTH ABOVE.
12 English
HP Ergo 1024 User’s Guide
Environmental Information
Some states or provinces do not allow limitations on warranty, so the above limitation
or exclusion may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state, or province to province.
Limitation of Liability and Remedies
THE REMEDIES PROVIDED ABOVE ARE YOUR SOLE AND EXCLUSIVE REMEDIES.
IN NO EVENT SHALL HP BE LIABLE FOR ANY OTHER DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON
WARRANTY, CONTRACT, TORT, OR ANY OTHER LEGAL THEORY.
The foregoing limitation of liability shall not apply in the event that any HP product
sold hereunder is determined by a court of competent jurisdiction to be defective and
to have directly caused bodily injury, death, or property damage; provided, that in no
event shall HP's liability for property damage exceed the greater of $50,000 or the
purchase price of the specific product that caused such damage.
Some states or provinces do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
Environmental Information
HP has a strong commitment toward the environment. Your HP display has
been designed to respect the environment as much as possible.
HP can also take back your old display for recycling when it reaches the end of
its useful life.
In fact, HP has a product take-back program in several countries. The
collected equipment is sent to of HP’s recycling facilities in Europe or the
USA. As many parts as possible are reused. The remainder is recycled. Special
care is taken for batteries and other potentially toxic substances, which are
reduced to non-harmful components through a special chemical process. If
you require more details about HP’s product take-back program, contact your
dealer or your nearest HP Sales Office.
The cathode ray tube used in this display does not contain cadmium.
English 13
HP Ergo 1024 User’s Guide
Regulatory Information
Regulatory Information
CONFORMITY DECLARATION
according to ISO/IEC Guide 22 and EN 45014
Manufacturer’s Name: HEWLETT-PACKARD
Manufacturer’s Address: 5, Avenue Raymond Chanas — EYBENS
38053 GRENOBLE CEDEX 09
declares, that the product:
Product Name: HP Ergo 1024 15-inch Display
Model Number: D2830*, D2831* (see Note)
conforms to the following Product Specifications:
SAF ET Y
International: IEC 950:1991 + A1 + A2 + A3
European: EN 60950:1992 + A1 + A2 + A3
EMC
CISPR 22:1993 / EN 55022:1994 - Class B
EN 50082-1:1992
IEC 801-2:1992 / prEN 55024-2:1992 - 4kV CD, 8 kV AD
IEC 801-3:1984 - 3V/m
IEC 801-4:1988 / prEN 55024-4:1992 - 1 kV Power lines
IEC 555-2:1982 + A1:1985 / EN 60555-2:1987
IEC 1000-3-3:1994 / EN 61000-3-3:1995
Supplementary information:
Directive 89/336/EEC amended by the Directive 93/68/EEC, and
carries the CE-marking accordingly.
Note: * can be any alphanumeric character, or blank.
Grenoble, August, 1997 Quality Manager
the product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC
Jean Marc JULIA
14 English
HP Ergo 1024 User’s Guide
Regulatory Information
Notice for the USA: FCC Statement
Federal Communications Commission (FCC) Radio
Frequency Interference Statement (USA Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protections against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try one of more of the following measures:
•
Relocate the radio or television antenna.
•
Move the computer away from the radio or television.
•
Plug the computer into a different electrical outlet, so that the computer and the radio or television are on
separate electrical circuits.
•
Make sure that all your peripheral devices are also FCC Class B certified.
•
Make sure you use only shielded cables to connect peripheral devices to your computer.
•
Consult your computer dealer, Hewlett-Packard, or an experienced radio/television technician for help.
WA R N IN G
Hewlett-Packard’s system certification tests were conducted with HP-supported peripheral devices and HP
shielded cables, such as those you received with your system. Cables used with this computer must be properly
shielded to comply with the requirements of the FCC.
Changes or modifications not expressly approved by Hewlett-Packard could void the user’s authority to operate
the equipment.
X-Ray Radiation Notice
When operating, this product emits x-rays; however, it is well shielded and meets the safety and health
requirements of various countries, such as the Radiation Act of Germany and the Radiation Control for Health
and Safety Act of the United States.
Radiation emitted by this product is less than 0.1 mR/hr (1uSv/hr) at a distance of 10 centimeters from the
surface of the cathode ray tube. The x-ray radiation primarily depends on the characteristics of the cathode ray
tube and its associated low voltage and high voltage circuitry. Internal controls have been adjusted to ensure
safe operation. Only qualified personnel should perform any internal adjustments as specified in the service
manual for this product.
Replace the cathode ray tube with an identical CRT only.
English 15
HP Ergo 1024 User’s Guide
Regulatory Information
Notice for Japan
Notice for Canada
This Class “B” digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du règlement sur le matériel brouilleur du
Canada.
Notice for Korea
16 English
Loading...