HP DL160 User Manual

Download

QuickSpecs

Overview

HP ProLiant DL160 Generation 5

Hot Plug SAS/SATA and Non-Hot Plug SATA Models

Front View:

Access panel

Quad-Core Intel® Xeon® 5400 series processors (supports up to two)

Eight PC2-5300 (DDR2-667) or PC2-6400 (DDR2-800) fully buffered DIMM memory slots

Power supply (650 Watts)

System fans

Optional CD-RW or DVD-ROM drive

Two USB ports

Power on/off & system LEDs

Optional 3rd and 4th 3.5” Non-Hot plug SATA or hot plug SAS/SATA hard drive bays

10.

Standard 1st and 2nd 3.5” Non-Hot plug SATA or hot plug SAS/SATA hard drive bays

11.

Expansion Slots: Non-Hot Plug Models – Two available x16 PCI-Express Gen2 slots Hot Plug Models – One available x16 PCI-Express slot Gen2 slot

Rear View:

Power Supply Cable Socket

PS/2 Mouse Port

PS/2 Keyboard Port

Two GbE LAN ports for NIC 1 and NIC 2 (RJ-45)

Rear USB ports

LO100i 10/100 Mbps LAN port for IPMI management (RJ-45)

Video Port

Serial Port

Low-Profile PCI Express x8/PCI-X riser board slot cover

10.

Standard height/full-height PCI Express x16/PCI-X riser board

What's New

Support for up 400GB 3G 10K 3.5" DP SAS Enterprise Hard Drive

At A Glance

The HP ProLiant DL160 G5 server is an affordable 1U, dual processor capable server equipped with essential performance features that provide customers with a platform to design a fully optimized solution. It is ideal for general purpose and high performance computing.

Processors

Supports up to two Intel® Quad-Core 5400 or Dual-Core 5200 sequence processors

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 1

QuickSpecs

Overview

Quad-Core Intel® Xeon® processors 5400 sequence with 12 MB Level 2 cache Dual-Core Intel® Xeon® processors 5200 sequence with 6 MB Level 2 cache

Intel® 5400 Chipset

Memory

Internal Drive Support

Network Controller

Storage Controllers

Expansion Slots

Management

USB Ports

Optical Drive

Power Supply

Additional Features

Form Factor

: Supports up to 64 GB of PC2-5300 (DDR2-667) and up to 32 GB of PC2-6400 (DDR2-800) fully buffered DIMMs (DDR2-667) with Advanced ECC

: Support for up to four 3.5" Non-Hot plug serial ATA (SATA) hard drives or; Support for up to four 3.5" Hot plug Serial Attached SCSI (SAS) or SATA hard drives.

NOTE:

Installation of the Hot Plug Backplane 1U 2S Kit (445985-B21) is required if ordering third or fourth Hard Drives for Hot Plug models only.

Internal storage capacity of up to 1.0TB (4 x 1TB Hot Plug 3.5" SATA), 3.0TB (4 x 750 Non-Hot Plug SATA) or

4.0TB (4 x 1TB Hot Plug 3.5" SAS)

Two embedded NC105i PCIe Gigabit Server Adapters

Non-Hot Plug SATA Models: HP Embedded SATA RAID Controller

NOTE:

Transfer rate: 1.5 Gb/s SATA

Hot Plug SAS/SATA Models: HP SC40Ge 4-Port Internal SAS HBA with RAID 0, 1

NOTE:

When using the SC40Ge with SATA Hard Drives, 1.5G SATA Hard Drives are required.

NOTE:

Transfer rate: 1.5 Gb/s SATA, 3Gb/s SAS

Non-Hot Plug Models: Two available PCI Express 2.0 slots:

Slot 1: full-length/full-height PCI-Express 2.0 x16 Slot 2: low-profile/half-height PCI-Express 2.0 x16

Hot Plug Models: One available PCI-Express slot:

Slot 1: full-length/full-height PCI-Express 2.0 x16 Slot 2: low-profile/half-height PCI-X slot populated by the SAS/SATA storage controller

: HP Lights Out 100i Advanced Remote Management with new licensed key activated upgrades for Virtual KVM and virtual media support. LO100i management support for the DL160 G5 includes: IPMI 2.0 & SMASH CLP support ROM Setup Utility Improvements to virtual media with the addition of USB 2.0 drives and protocol support for much faster transfer speeds and DVD-ROM support plus simplified virtual media (floppy and CD with no FTTP server requirements) Enhanced browser interface and embedded KVM over IP provides OS-independent remote graphical console New Licenses that have EULAs with one-time, optional, license activation key to allow for easy, future upgrades which will be chargeable when they become available.

Five USB ports (two front, one internal, two rear)

Support for one (optional): DVD-ROM, DVD/CD RW

: 650W Power Supply (Non-Hot Plug, Autoswitching) Optional high-efficiency model

NOTE:

Optional high-efficiency model requires the purchase of HP Power Supply Backplane (453652-

B21)

Support for:

NVIDIA Quadro FX3700 512MB PCIe x 16 graphics card NVIDIA Quadro FX1700 512MB PCIe x 16 graphics card

: Rack (1U) Fixed mounting rails included with all models

HP ProLiant DL160 Generation 5

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 2

QuickSpecs

Overview

HP ProLiant DL160 Generation 5

Deployment/Serviceability

Tool-less access to all system components for easy in rack serviceability Customer Self Repair (CSR): HP products are designed with many CSR parts to minimize repair time and allow for greater flexibility in performing defective parts replacement

Warranty

: This product is covered by a global limited warranty and supported by HP Services and a worldwide network of HP Authorized Channel Partners. Hardware diagnostic support and repair is available for one year from date of purchase. Support for software and initial setup is available for 90 days from date of purchase. Enhancements to warranty services are available through HP Care Pack services or customized service agreements. SATA hard drives have a one year warranty. SAS Midline drives have a one-year warranty. SAS Enterprise drives have a three-year warranty.

NOTE:

Server Warranty includes 1 year Parts, 1 year Labor, 1-year on-site support with next business day response. Warranty repairs may be accomplished through the use of Customer Self Repair (CSR) parts. These parts fall into two categories: 1) Mandatory CSR parts are designed for easy replacement. A travel and labor charge will result when customers decline to replace a Mandatory CSR part; 2) Optional CSR parts are also designed for easy replacement but may involve added complexity. Customers may choose to have HP replace Optional CSR parts at no charge. Additional information regarding worldwide limited warranty and technical support is available at:

http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 3

QuickSpecs

Standard Features

HP ProLiant DL160 Generation 5

NOTE:

specifications, please visit:

NOTE:

Factory Integrated Models" section.

Processor

One of the following depending on Model

For a brief, printer friendly data sheet that describes this product and informs you of the essential capabilities and

http://h71028.www7.hp.com/ERC/downloads/4AA1-6954ENW.pdf

For the Standard Features shipped in the Factory Integrated Models, please see the "Configuration Information -

Quad-Core Intel® Xeon® processor X5482 (3.20 GHz, 120W, 1600MHz FSB)

NOTE:

more details.

Quad-Core Intel® Xeon® processor X5472 (3.00 GHz, 120W, 1600MHz FSB)

Quad-Core Intel® Xeon® processor X5470 (3.33 GHz, 120W, 1333MHz FSB)

NOTE:

more details.

Quad-Core Intel® Xeon® processor X5460 (3.16 GHz, 120W, 1333MHz FSB)

NOTE:

more details.

Quad-Core Intel® Xeon® processor L5430 (2.60 GHz, 50W, 1333MHz FSB)

NOTE:

more details.

Quad-Core Intel® Xeon® processor L5420 (2.50 GHz, 50W, 1333MHz FSB)

Quad-Core Intel® Xeon® processor L5410 (2.33 GHz, 50W, 1333MHz FSB)

Quad-Core Intel® Xeon® processor E5472 (3.00 GHz, 80W, 1600MHz FSB)

Quad-Core Intel® Xeon® processor E5462 (2.80 GHz, 80W, 1600MHz FSB)

Quad-Core Intel® Xeon® processor E5430 (2.66 GHz, 80W, 1333MHz FSB)

Quad-Core Intel® Xeon® processor E5405 (2.00 GHz, 80W, 1333MHz FSB)

Dual-Core Processors

Dual-Core Intel® Xeon® processor X5272 (3.40 GHz, 80W, 1600MHz FSB)

Dual-Core Intel® Xeon® processor L5240 (3.00 GHz, 40W, TDP, 1333MHz FSB)

NOTE:

more details.

Available through Configure To Order only. See Factory Integration Models section for

Upgradeability

Chipset

Cache Memory

Memory Protection

Memory

Upgradeable to two processors

Intel® 5400 Chipset

12 MB (2 x 6 MB) Level 2 cache (5400 sequence)

6 MB (1 x 6 MB) Level 2 cache (5200 sequence)

Advanced ECC capabilities

Type

Standard

Maximum

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

PC2-5300 (DDR2-667) and PC2-6400 (DDR2-800)

1 GB

32 GB 64 GB

(2 x 512 MB)

(8 x 4 GB) PC2-6400 (8 x 8 GB)

Page 4

QuickSpecs

Standard Features

HP ProLiant DL160 Generation 5

Network Controller

Expansion Slots #

Storage Controller

Two embedded NC105i PCIe Gigabit Server Adapters

Technology

PCI-Express

2.0

PCI-X

***

PCI-Express

2.0

PCI-X

***

NOTE:

All slots can accept universal keyed PCI cards

* Default bus assignment. Inserting cards with PCI bridges may alter the actual bus assignment number.

** Slots are enumerated differently based on OS. MS OS's enumerate from lowest to highest Device ID by bus (starting with the lowest bus).

*** PCI-X bus speed will be 133MHz when only one PCI-X card is installed. It will be 100MHz when both slots have PCI-X cards installed.

Non-Hot Plug SATA Models

Hot Plug SATA/SAS Models

NOTE:

A diskette drive, USB floppy drive key or virtual FDD using LO100 Advanced Pack is needed to install storage controller drivers during a Windows operating system installation from a CD.

Bus Width

x16 x16

64-bit

x16 x16

64-bit

HP Embedded SATA RAID Controller (integrated into the south-bridge) supporting SW RAID 0,1

NOTE:

HP SC40Ge HBA with RAID 0, 1

NOTE:

Hard Drives are required.

NOTE:

Connector

Width

N/A

Transfer rate: 1.5 Gb/s SATA

When using the SC40Ge with SATA Hard Drives, 1.5G SATA

Transfer rate: 1.5 Gb/s SATA, 3 Gb/s SAS

Bus

Number

1 0

5 1

6 3

5 1

Device No.**

Form Factor

Full length,

full height

Full length,

full height

Low Profile

3.3 volts

Notes

Storage

Maximum Internal Storage

Optical Drives:

DVD-ROM

DVD/CD RW

Diskette Drives

Drive Bays:

Non-Hot Plug SATA

Hot Plug SATA/SAS

Non-Hot Plug SATA

Hot Plug SATA

Hot Plug SAS

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

8x IDE (ATAPI) DVD-ROM drive, slim (optional)

24x IDE (ATAPI) CD-ROM drive (optional)

Via USB only

Up to 4 Non-hot plug SATA 3.5" drives

Up to 4 Hot plug SAS/SATA 3.5" drives

3.0TB

4.0TB

4 x 750GB

4 x 1TB

Page 5

QuickSpecs

Standard Features

HP ProLiant DL160 Generation 5

Interfaces

Graphics

Form Factor

Server Management Stand Alone Software Product and ProLiant Essentials

Parallel

Network RJ-45(Ethernet)

Serial

Pointing Device (Mouse)

Graphics

Keyboard

USB

32MB shared supporting 1600x1200x16M resolution

Rack (1U), (1.75 in/4.45 cm)

Lights-Out 100i

None

2 10/100/1000 NIC ports (plus 1 dedicated for the HP ProLiant Lights Out 100i Remote Management)

5 (two front, one internal, two rear)

NOTE:

regarding USB support:

http://h18004.www1.hp.com/products/servers/platforms/usbsupport.html

HP Lights-Out 100i Remote Management delivers affordable, entry level remote management capabilities for HP ProLiant 100 Series servers with embedded LO100i. It allows customers or their service providers to remotely manage ProLiant 100 Series servers remotely over a LAN or the Internet and consists of the following:

Please see the following URL for additional information

ProLiant Essentials Rapid Deployment Pack

LO100i Standard is embedded remote management and provides basic remote control via telnet, browser, and IPMI 2.0 and SMASH LO100i Advanced Pack License are upgrades for essential, secure, remote control, serial console, virtual media, and Virtual KVM (graphical hardware-based, remote console)

NOTE:

Flexible and volume quantity (AKA) license kits are available for the Lights-Out 100i Lights-Out 100 Advanced Pack licenses as well as Electronic License To Use (E-LTU). AKA Tracking licenses require a 100 unit minimum forecast at initial contract signing. For these additional part numbers, please refer to each software products' QuickSpecs at this link for more information:

http://h18004.www1.hp.com/products/servers/management/ remotemgmt.html

Rapid Deployment Pack (RDP) extends HP Systems Insight Manager with a complete deployment solution for HP ProLiant servers. RDP provides a central location to configure server hardware, deploy Windows, Linux and VMware ESX operating environments and install using images and scripted profiles. For more information, visit:

http://www.hp.com/go/rdp

NOTE:

Flexible and volume quantity license kits are available for ProLiant Essentials Value Packs. Refer to:

http://www.hp.com/servers/proliantessentials

Essentials Value Pack product QuickSpecs for more information.

or the various ProLiant

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 6

QuickSpecs

Standard Features

HP ProLiant DL160 Generation 5

Core Infrastructure Management

HP Serviceguard for Linux (SG/LX)

HP Systems Insight Manager

Subscriber's Choice

ROMPaq, software and latest drivers

HP Serviceguard for Linux is a high availability clustering solution designed to protect applications and services from a wide variety of software and hardware failures, monitoring the health of each server (node) and quickly responding to failures such as those that affect system processes, system memory, LAN media and adapters, and application processes.

The following is a quick summary of HP Serviceguard for Linux features and support. For the most recent list of Linux distributions & kernels, servers and storage supported with Serviceguard for Linux, see the Serviceguard for Linux Datasheet, available at:

HP Systems Insight Manager (HP SIM) provides a unified, secure and extensible standards-based environment to centrally manage servers, storage and other infrastructure devices, (both HP and non-HP) across multiple operating system platforms.

Subscriber's Choice Driver and Support Alerts/Notifications is a webbased email subscription service that provides software and driver change notifications for ProLiant products. Sign up at:

http://www.hp.com/go/subscriberschoice

and customize your profile to receive various new alerts as they become available, on a weekly or monthly basis.

The latest software, drivers, and firmware fully optimized and tested for your ProLiant server and options, available through software and drivers download pages website at:

http://www.hp.com/go/support

http://www.hp.com/go/sglx/info

Supported Linux Distributions:

Red Hat EL 4 Red Hat EL 5 SUSE SLES10

Supported Server Platforms

HP Integrity BladeSystem to Superdome HP ProLiant BladeSystem p-Class & c-Class HP ProLiant DL HP ProLiant ML IBM System x Dell PowerEdge Sun x64 Fujitsu Siemens PRIMERGY

Supported Virtual Machines

SG/LX in HP Integrity Virtual Machines guests SG/LX in VMware ESX guests SG/LX in Red Hat and SUSE Xen hosts (DOM0)

Application Integration Toolkits

HP Serviceguard for Linux Oracle Database Toolkit HP Serviceguard Extension for SAP on Linux (SGeSAP/LX) Free Application Integration Toolkits:

Apache MySQL NFS PostgreSQL Samba Tomcat Sendmail

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 7

QuickSpecs

Standard Features

Software updates are distributed by HP Services to customers with support contracts

HP ProLiant DL160 Generation 5

Disaster Tolerant Solutions HP Serviceguard for Linux Extended Distance Cluster (XDC) extends cluster distances up to 100 km, utilizes software RAID mirroring for data replication and is storage array independent HP StorageWorks XP/EVA Cluster Extension Software for Linux (CLX) works seamlessly with HP Serviceguard for Linux, HP StorageWorks Continuous Access, and HP Disk Arrays to automate failover and failback between sites

Industry Standard Compliance

Manageability

NOTE:

or see the HP Serviceguard for Linux QuickSpecs.

NOTE:

include one year of 24 x 7 HP Software Technical Support and Update Service ensuring rapid access to HP support staff and proactive delivery of software updates. For more information about this service, please visit:

ACPI V2.0 Compliant

PCI 2.2 Compliant

PXE Support

WOL Support

Microsoft® Logo certifications

IPMI 2.0, SMASH CLP compliant

HP Lights-Out 100i Standard provides the following OS-independent remote control capabilities:

For additional information on HP Serviceguard for Linux, visit:

HP Serviceguard for Linux products for HP ProLiant and select 3rd party x86 class servers

http://www.hp.com/services/swsupport

Virtual power System event log access System health Remote serial console (serial redirection) Browser, Telnet access SMASH-CLP compliant IPMI 2.0 compliant

http://www.hp.com/go/sglx

Security

HP Lights-Out 100i Advanced Pack provides license key activated upgrades to the following:

Virtual KVM (KVM over IP functionality embedded on the system board)

Power-on password

Setup password

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 8

QuickSpecs

Standard Features

HP ProLiant DL160 Generation 5

Server Power Cords

UPS and PDU Power Cord Matrix

Power Supply

System Fans

OS Support

One 6' Highline (IEC-IEC) power cord ships standard

NOTE:

HP ProLiant DL servers no longer ship standard with NEMA power cords (163719-002) that allow connection to 110V US wall outlets in a home or office. ProLiant DL servers are primarily connected to PDU's in data center racks so they now ship standard with only a PDU power cord (416151-B21). If a user wishes to power a ProLiant DL server using a 110V receptacle (NEMA-15), the NEMA power cord (227099-001) must be ordered separately.

If customers require a local power cord, they can check the power cord matrix for the appropriate cord. Please see the following power cord matrix:

Please see the UPS and PDU cable matrix that lists cable descriptions, requirements, and specifications for UPS and PDU units:

http://h18004.www1.hp.com/products/servers/proliantstorage/power-protection/index.html

650 Watts, auto-switching, PFC (Power Factor Correcting)

NOTE:

6 system fans ship standard; Non-hot plug, Non-redundant

Microsoft Windows Server 2003 R2 Microsoft Windows Server 2008 Microsoft Windows Small Business Server 2008 Microsoft Windows Essential Server 2008 Red Hat Enterprise Linux SUSE Linux Enterprise Server Sun Solaris for x64/x86-based Systems

NOTE:

Virtualization Software and latest listing of software drivers available for your server, please visit our Support Matrix at:

http://www.hp.com/support/DL160G5

Factory upgradeable to high-efficiency (HE) power supply for lower TCO

For more information on HP's Certified and Supported ProLiant Servers for OS and

http://www.hp.com/go/supportos

http://www.hp.com/go/powercordmatrix

and our driver download page

Rack Airflow Requirements

Rack 10000 series Cabinets

The increasing power of new high-performance processor technology requires increased cooling efficiency for rack-mounted servers. The 10000 Series Racks provide enhanced airflow for maximum cooling, allowing these racks to be fully loaded with servers using the latest processors.

CAUTION:

adequate airflow and to prevent damage to the equipment:

Front and rear doors: If your 42U server rack includes closing front and rear doors, you must allow 5,350 sq cm (830 square inches) of hole evenly distributed from top to bottom to permit adequate airflow (equivalent to the required 64 percent open area for ventilation). Side: The clearance between the installed rack component and the side panels of the rack must be a minimum of 7 cm (2.75 inches)

CAUTION:

This arrangement ensures proper airflow. Using a rack without blanking panels results in improper cooling that can lead to thermal damage.

If a third-party rack is used, observe the following additional requirements to ensure

Always use blanking panels to fill all remaining empty front panel U-spaces in the rack.

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 9

QuickSpecs

Standard Features

HP ProLiant DL160 Generation 5

Rack Support

Factory Express Portfolio for Servers and Storage

NOTE:

CD provided with the server, or to the server documentation located in the Support section at the following URL:

The DL Fixed Rail System supports installation in racks with square or round mounting holes (including Compaq/HP 7000, 9000, 10000 and HP series), with an adjustment range of 24" - 36". Installation into Telco 2 post, and 4 post, or threaded holes racks requires a 3rd party option kit. For additional information, please visit:

HP Factory Express offers configuration, customization, integration and deployment services for HP servers and storage products. Customers can choose how their factory solutions are built, tested, integrated, shipped and deployed.

Factory Express offers service packages for simple configuration, racking, installation, complex configuration and design services as well as individual factory services, such as image loading, asset tagging, and custom packaging. HP products supported through Factory Express include a wide array of servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades, HP BladeSystem, HP 9000 servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries and configurable network switches.

For more information on Factory Express services for your specific server model please contact your sales representative or go to:

For additional information, refer to the Setup and Installation Guide or the Documentation

www.hp.com/servers/dl160

www.racksolutions.com

http://www.hp.com/go/factory-express

HP Enterprise Configurator

Service and Support

The HP eConfigure Enterprise Configurator now provides factory default racking for our HP hardware portfolio. This approach is aligned with our strategic direction to meet the needs and expectations of our valued customers. If you require "custom" rack configuration, please contact HP's Customer Business Center or an Authorized Partner for assistance.

HP Care Pack Services provide total care and support expertise with committed response designed to meet your IT and business needs.

HP Care Pack services include coverage for the HP branded hardware options qualified for the server that are purchased at the same time or afterward and internal to the enclosure. It also includes the 22" and smaller external monitors and tower UPS options up to 3kVA. These items will be covered at the same service level and for the same coverage period as the server. Coverage of UPS Battery is not included and standard warranty terms & conditions apply. For servers or storage systems installed within a rack, service also covers all HP qualified rack options installed within the same rack.

To fully capitalize on your HP ProLiant servers' capabilities requires a service partner who thoroughly understands your server technology and systems environment. HP Services, an industry leader in provision of multi vender support solutions provides a range of support services designed to meet the varying needs of business. Whether an SMB or large global corporation HP has a ProLiant server support offer to help you speedily deploy and maximize system uptime.

Recommended Service

management.

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

– Simplify ProLiant solution implementation, maintenance and

Page 10

QuickSpecs

Standard Features

HP ProLiant DL160 Generation 5

Support Service Deployment Service

Enhanced Service

Support Service Deployment Service

Installation & Start-Up of a ProLiant server and Microsoft or Linux O/S per the Customer Description and/or Data Sheet. To be delivered on a scheduled basis 8am-5pm, M-F, excl. HP holidays.

For a complete listing of service offerings and information visit:

http://www.hp.com/services/proliantservices http://www.hp.com/go/proliant/carepack

– 3 Year, 9x5 Next Business Day coverage, excluding HP holidays only

– Hardware Installation only

– Optimize service level to increase IT performance and availability

– 3 Year 13x5 Same Business Day, 4-Hour response coverage

– Installation and Start-up only

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 11

QuickSpecs

HP ProLiant DL160 Generation 5

HPC Interconnects

NOTE:

High Performance Computing (HPC) interconnect technologies are available for the DL160 G5 under the Cluster Platform product portfolio. These high-speed interconnects are fully supported by HP when they are part of these configure to order clusters. Solutions can be defined with a lot of flexibility with the help of configuration tools. Please visit the following URL to configure HPC Clusters with InfiniBand, Gigabit Ethernet or Myrinet Interconnects:

http://www.hp.com/techservers/clusters/ucp/index.html

HPC Interconnects

InfiniBand

Gigabit Ethernet

Myrinet XP

PCI-X and PCI-Express adapters

Use embedded ports

PCI-X Rev D, Rev E and Rev F adapters

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 12

QuickSpecs

HP ProLiant DL160 Generation 5

Models

Non-Hot Plug Serial ATA (SATA) Models

NOTE:

Non-Hot Plug models are not upgradeable to Hot Plug. Non-Hot Plug models require the addition of the HP HBA SAS-SATA 4x1LN Cable Kit (P/N: 452130-B21) in order to connect a hardware RAID controller.

HP DL160 G5 X5472 Non-Hot Plug SATA, 2GB, (1P)

445198-xx1

HP DL160 G5 E5430 Non-Hot Plug SATA, 1GB, (1P)

445197-xx1

HP DL160 G5 E5405 Non-Hot Plug SATA, 1GB, (1P)

445196-xx1

Processor(s)

One of the following depending on model

Cache Memory

Memory

One of the following depending on model

Network Controller

Storage Controller

Hard Drive

Internal Storage

Optical Drive

Form Factor

(1) Quad-Core Intel® Xeon® processor X5472 (3.00 GHz, 120W, 1600 MHz FSB) (1) Quad-Core Intel® Xeon® processor E5430 (2.66 GHz, 80W, 1333MHz FSB) (1) Quad-Core Intel® Xeon® processor E5405 (2.00 GHz, 80W, 1333MHz FSB)

12MB (2 x 6MB) Level 2 cache

2GB (2 x 1GB) PC2-5300 DDR2 fully buffered DIMMs (667MHz) with Advanced ECC (X5472 models) 1GB (2 x 512MB) PC2-5300 DDR2 fully buffered DIMMs (667MHz) with Advanced ECC (E5430, E5405 models)

Two embedded NC105i PCIe Gigabit Server Adapters

HP Embedded SATA RAID Controller

160GB NHP SATA HDD

3.0TB maximum (4 x 750GB Non-Hot plug 3.5" SATA hard drives)

Optional CD/DVD-ROM, DVD/CD RW

Rack (1U)

Hot Plug Serial ATA (SATA)/ Serial Attached SCSI (SAS) Models

HP DL160 G5 X5472 Hot Plug SAS/SATA, 2GB, (1P)

445204-xx1

HP DL160 G5 E5430 Hot Plug SAS/SATA, 1GB, (1P)

445203-xx1

HP DL160 G5 E5405 Hot Plug SAS/SATA 1GB, (1P)

445202-xx1

Processor(s)

One of the following depending on model

Cache Memory

Memory

One of the following depending on model

Network Controller

Storage Controller

Hard Drive

Internal Storage

Optical Drive

Form Factor

12 MB (2 x 6 MB) Level 2 cache

2 GB (2 x 1 GB) PC2-5300 DDR2 fully buffered DIMMs (667MHz) with Advanced ECC (X5472 models) 1 GB (2 x 512 MB) PC2-5300 DDR2 fully buffered DIMMs (667MHz) with Advanced ECC (E5430, E5405 models)

Two embedded NC105i PCIe Gigabit Server Adapters

HP SC40Ge SAS HBA with RAID

None ship standard (up to 4 Hot Plug SATA or SAS drives supported)

4.0TB max. (4 x 1TB Hot Plug 3.5" SAS/SATA hard drives)

Optional CD/DVD-ROM, DVD/CD RW

Rack (1U)

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 13

QuickSpecs

Models

HP ProLiant DL160 Generation 5

Country Code Key

xx = 00

xx = 20

xx = 29

xx = 37

xx = 42

xx = AA

U.S.

Brazil (P/N 445202-201 only)

Japan

APD

Euro

PRC

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 14

QuickSpecs

HP ProLiant DL160 Generation 5

Configuration Information - Factory Integrated Models

NOTE:

This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid configurations are ordered, HP recommends the use of an HP approved configurator. Contact your local sales representative for additional information.

NOTE:

start with a CTO Chassis.

NOTE: NOTE:

HP does not allow factory integration of options into standard models listed above. Configure-to-order servers must

This product offering does not support HP Factory Express Server Configuration Level 1. FIO indicates that this option is a Factory Installable Option.

Step 1: Base Configuration (choose one of the following configurable models)

Non-Hot Plug SATA Model

NOTE:

Non-Hot Plug models are not upgradeable to Hot Plug. Non-Hot Plug models require the addition of the HP HBA SAS-SATA 4x1LN Cable Kit (P/N: 452130-B21) in order to connect a hardware RAID controller.

HP ProLiant DL160 G5 Non-Hot Plug SATA Rack CTO Chassis

Factory Integrated Model ships with:

Two embedded NC105i PCIe Gigabit Server Adapters (WOL & PXE-capable)

Two available PCI-Express 2 slots:

Slot 1: full-length/full-height Slot 2: low-profile/half-height

650 Watt Power Supply

One Highline IEC Power Cord

6 Non-Hot Plug Fans

Rack (1U), (1.75 in / 4.45 cm) Fixed Rails

Hot Plug Model

HP ProLiant DL160 G5 Hot Plug SAS/SATA Rack CTO Chassis

Factory Integrated Model ships with:

Two embedded NC105i PCIe Gigabit Server Adapters (WOL & PXE-capable)

Two available PCI-Express 2 slots:

445192-B21

445193-B21

Slot 1: full-length/full-height Slot 2: low-profile/half-height

650 Watt Power Supply

One Highline IEC Power Cord

6 Non-Hot Plug Fans

Rack (1U), (1.75 in / 4.45 cm) Fixed Rails

Step 2: Choose Required Options (only one of the following from each list unless otherwise noted)

Processors

Quad-Core Processors

Quad-Core Intel® Xeon® processor X5482 (3.20 GHz, 120W, 1600MHz FSB), FIO

NOTE:

B21.

If 2 processors are desired, select one 495614-L21 and one 495614-

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

495614-L21

Page 15

QuickSpecs

Configuration Information - Factory Integrated Models

HP ProLiant DL160 Generation 5

Quad-Core Intel® Xeon® processor X5472 (3.00 GHz, 120W, 1600MHz FSB), FIO

NOTE:

If 2 processors are desired, select one 462465-L21 and one 462465B21.

Quad-Core Intel® Xeon® processor X5470 (3.33 GHz, 120W, 1333MHz FSB), FIO

NOTE:

B21.

Quad-Core Intel® Xeon® processor X5460 (3.16 GHz, 120W, 1333MHz FSB), FIO

NOTE:

B21.

Quad-Core Intel® Xeon® processor L5430 (2.60 GHz, 50W, 1333MHz FSB), FIO

NOTE:

B21.

Quad-Core Intel® Xeon® processor L5420 (2.50 GHz, 50W, 1333MHz FSB), FIO

NOTE:

B21.

Quad-Core Intel® Xeon® processor L5410 (2.33 GHz, 50W, 1333MHz FSB), FIO

NOTE:

B21.

Quad-Core Intel® Xeon® processor E5472 (3.00 GHz, 80W, 1600MHz FSB), FIO

NOTE:

B21.

Quad-Core Intel® Xeon® processor E5462 (2.80 GHz, 80W, 1600MHz FSB), FIO

NOTE:

B21.

Quad-Core Intel® Xeon® processor E5430 (2.66 GHz, 80 W, 1333 MHz FSB), FIO

NOTE:

B21.

Quad-Core Intel® Xeon® processor E5405 (2.00 GHz, 80W, 1333MHz FSB), FIO

NOTE:

B21.

Dual-Core Processors

Dual-Core Intel® Xeon® processor X5272 (3.40 GHz, 80W, 1600MHz FSB)

NOTE:

B21.

Dual-Core Intel® Xeon® processor L5240 (3.00 GHz, 40W, 1333MHz FSB), FIO

NOTE:

B21.

If 2 processors are desired, select one 495612-L21 and one 495612-

If 2 processors are desired, select one 446085-L21 and one 446085-

If 2 processors are desired, select one 495616-L21 and one 495616-

If 2 processors are desired, select one 495479-L21 and one 495479-

If 2 processors are desired, select one 448369-L21 and one 448369-

If 2 processors are desired, select one 448365-L21 and one 448365-

If 2 processors are desired, select one 463076-L21 and one 463076-

If 2 processors are desired, select one 446079-L21 and one 446079-

If 2 processors are desired, select one 446077-L21 and one 446077-

If 2 processors are desired, select one 448371-L21 and one 448371-

If 2 processors are desired, select one 448373-L21 and one 448373-

462465-L21

495612-L21

446085-L21

495616-L21

495479-L21

448369-L21

448365-L21

463076-L21

446079-L21

446077-L21

448371-L21

448373-L21

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 16

QuickSpecs

Configuration Information - Factory Integrated Models

HP ProLiant DL160 Generation 5

Memory

Hard Drive

1 GB FBD PC2-5300 2 X 512 MB Kit

2 GB FBD PC2-5300 2 X 1 GB Kit

4 GB FBD PC2-5300 2 X 2 GB Kit

8 GB FBD PC2-5300 2 X 4 GB Kit

Dual Rank

4 GB FBD PC2-6400 800MHz 2 x 2 GB Dual Rank Kit

8 GB FBD PC2-6400 2 x 4 GB Dual Rank Kit

16 GB FBD PC2-5300 2 x 8 GB Dual Rank Kit

64 GB FBD PC2-5300 8 x 8 GB Dual Rank Kit

Low Power

2 GB FBD PC2-5300 2 X 1 GB Low Power Kit

4 GB FBD PC2-5300 2 x 2 GB Low Power Kit

8 GB FBD PC2-5300 2 x 4 GB Low Power Kit

NOTE:

Transfer rates of drives are dependent on the maximum transfer rate supported by the HBA or Controller. Refer to the HBA or Controller technical specifications for details.

SATA Non-Hot Plug Midline (MDL) Drive

NOTE:

CTO Chassis Model (P/N 445192-B21).

NOTE:

Hot Plug CTO Chassis Models (445192-B21) in Step 1.

HP 750GB 3G SATA 7.2K NHP 3.5" MDL HDD

HP 500GB 3G SATA 7.2K NHP 3.5" MDL HDD

HP 250GB 3G SATA 7.2K NHP 3.5" MDL HDD

SATA Non-Hot Plug Entry (ETY) Drives

HP 160GB 3G SATA 7.2K NHP 3.5" ETY HDD

A minimum of one hard drive is required when purchasing Non-Hot Plug

SATA Non-Hot Plug Hard Drives ONLY required when purchasing Non-

397409-B21

397411-B21

397413-B21

397415-B21

484060-B21

484062-B21

413015-B21

495604-B21

461826-B21

461828-B21

466440-B21

462595-B21

458941-B21

458939-B21

458947-B21

Storage Controllers

NOTE:

CTO Chassis Model (P/N 445193-B21).

NOTE:

ONLY in the Hot Plug CTO Chassis Model (P/N 445193-B21).

HP SC44Ge Host Bus Adapter

NOTE:

Drives are required. Transfer rate: 1.5 Gb/s SATA, 3 Gb/s SAS.

HP SC40Ge 4 Internal PCIe SAS RAID Half Height HBA, FIO

NOTE:

(P/N 445193-B21).

NOTE:

Drives are required. Transfer rate 1.5 Gb/s SATA, 3 Gb/s SAS.

HP Smart Array E500/256MB Controller with Battery, FIO

NOTE:

one Battery-backed write cache upgrade (P/N 383280-B21) for the HP ProLiant DL160 G5 server based on battery space.

HP Smart Array E200/128 BBWC Controller

HP HBA SAS-SATA 4x1LN Cable Kit

A minimum of one SAS Controller is required when purchasing Hot Plug

The below storage controllers are intended for use with internal drives

When using the SC44Ge with SATA Hard Drives, 1.5G SATA Hard

Recommended HBA when purchasing Hot Plug CTO Chassis Model

When using the SC40Ge with SATA Hard Drives, 1.5G SATA Hard

Customers can only order one Smart Array E500/256MB Controller and

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

416096-B21

449363-B21

462105-B21

411508-B21

452130-B21

Page 17

QuickSpecs

HP ProLiant DL160 Generation 5

Configuration Information - Factory Integrated Models

NOTE:

This option is required for any internal port HBA or controller that has a standard 4 port SAS/SATA connector.

Step 3: Choose Additional Factory Integratable Options (only one of the following from each list unless otherwise noted)

Power Supply

HP High Efficiency Power Supply Kit, FIO

NOTE:

standard power supply and requires the purchase of Power Supply Backplane (p/n 453652-B21).

HP Power Supply Backplane, FIO

NOTE:

(P/N 453650-B2).

Selection of the HE Power Supply Unit will remove the 650 Watt

This backplane must be ordered with the High Efficiency Power Supply

453650-B21

453652-B21

Step 4: Choose Additional Options for Factory Integration

NOTE:

integration. Please contact an HP sales representative for additional information.

For additional options, please refer to the "Options" section below. Some options may not be available for factory

DA - 12902 Worldwide QuickSpecs — Version 19 — 1/26/2009

Page 18

QuickSpecs

Options

HP ProLiant DL160 Generation 5

Server Management Stand Alone Software Product and ProLiant Essentials

NOTE:

select ProLiant Essentials software products. Please see the appropriate Insight Control and ProLiant Essentials QuickSpecs for additional information.

Control

Lights-Out 100i Advanced Pack

HP Lights Out 100i Advanced Pack, No Media, 1-Server License

NOTE:

Lights-Out 100i Advanced Pack licenses as well as Electronic License To Use (E-LTU). AKA Tracking licenses require a 100 unit minimum forecast at initial contract signing. For these additional part numbers, please refer to each software products' QuickSpecs at this link for more information:

http://h18004.www1.hp.com/products/servers/management/remotemgmt.html

DEPLOY

Rapid Deployment Pack

ProLiant Essentials Rapid Deployment Pack No Media 1-Server License including 1 year of 24x7 Technical Support and Updates

NOTE:

Customer will receive a printed license entitlement certificate via physical shipment. The license entitlement certificate must be redeemed online or via fax in order to obtain the license activation key(s). Includes one year of 24 x 7 HP Software Technical Support and Update Service.

NOTE:

http://h18000.www1.hp.com/products/quickspecs/11053_div/11053_div.html

NOTE:

Essentials Value Packs. Refer to: or the various ProLiant Essentials Value Pack product QuickSpecs for more information.

Electronic licensing options are available for Insight Control suites and

Supports HP ProLiant DL 160 G5, DL165 G5 and DL185 G5 servers.

Flexible and volume quantity (AKA) license kits are available for the

This license allows 1 server to be deployed and managed via RDP.

For additional License Kits please see the QuickSpecs at:

Flexible and volume quantity license kits are available for ProLiant

http://www.hp.com/servers/proliantessentials

455342-B21

452151-B21