HP d538 User Manual

hp compaq d538 Series Personal Computer

illustrated parts map convertible minitower

Intel, Pentium, Intel Inside, and Celeron are trademarks of

Intel Corporation in the U.S. and other countries.

All other product names mentioned herein may be

trademarks of their respective companies.

The only warranties for HP products ansd services are set

forth in the expre ss warr anty statements accompanying such

products and services. Nothing herein should be cons tr ued

as constituting an additional warranty. HP shall not be liable

for technical or editorial errors or omissions contained

herein.

Product of the United States

February 2004

Document Number

358328-001

Miscellaneous Parts

Front I/O device 336446-001 2 Speaker 326776-001 3 PCI latch kit 339808-001 4 Hood sensor 267529-001 5 Solenoid lock with cable 336442-001 * 5.25” Bay bezel blank 335937-001 * Diskette drive bay bezel blank 356687-001 *# Heatsink with thermal grease and alcohol pad (see

reverse side) * Chassis fan 330457-001 * Mouse, 2-Button, PS/2 with scroll wheel 323614-001 * Mouse, 2-Button, USB, optical with scroll wheel 323617-001 * Mouse, 2-Button, wireless with scroll wheel 323616-001 * Mouse, 2-Button, USB, with scroll wheel 323615-001 * Rubber foot (4 ea. round, 4 ea. oval)) 336445-001 * Drive Key, 16 MB, carbon 324780-001 * Drive Key, 64 MB, carbon 331465-001 * Drive Key, 128 MB, carbon 331466-001 * Drive Key, 128 MB, carbonite 349988-001 * Nobel security lock without cable 335808-001 * Nobel security lock with cable 335809-001 * Return kit with buns 337910-001 * Real-time-clock battery 153099-001 * Port control cover 340400-001 * PCI extender card tray 335817-001

*Not shown #See back side for more information

333866-001

System Unit

1 Front bezel assembly with sub panel, 5.25” bezel

blank, and diskette drive bezel 2 Computer access panel 336444-001 3 Chassis assembly not spared 4

Power supply, PFC 308615-001

Mass Storage Devices (not illustrated)

40 GB\5400 RPM Hard drive 236921-001

80 GB\5400 RPM Hard drive 292208-001

40 GB\7200 RPM Hard drive 286692-001

80 GB\7200 RPM Hard drive 250185-001

160 GB\7200 RPM Hard drive 325306-001

250 GB\7200 RPM Hard drive 344058-001

80 GB SATA Hard drive 345713-001

160 GB SATA Hard drive 345712-001

Diskette drive with mounting screws 333505-001

48X CD-ROM drive with mounting screws 326773-001

48X/24X/48X CD-RW Drive 325308-001

48X/32X/48X CD-RW Drive 346788-001

48X/24X/48X +16X DVD/CD-RW Drive 325309-001

4X DVD+R/RW Drive 325317-001

16/40X DVD- ROM Drive 325313-001

Zip 250 Drive with mounting bracket 333504-001

Zip 250 Drive without mounting bracket 326772-001

Zip 750 Drive with mounting bracket 344060-001

Zip 750 Drive without mounting bracket 344059-001

PC MCIA Drive bay reader 331589-001

MultiBay drive adapter 335805-001

24X/10X/24X/8X CD-RW/DVD-ROM MultiBay

drive

24X/24X/24X/8X CD-RW/DVD-ROM MultiBay

drive

24X CD-ROM MultiBay drive 325314-001

24/10/24X CD-RW MultiBay drive 325315-001

8X/24X DVD-ROM MultiBay drive 325316-001

356593-001

325312-001

346789-001

Cables

IDE cable, 15.25”, two device (108950-047) 336448-001

1 2

Power switch/LED cable with switch holder 336447-001

Diskette drive cable (143218-006) 333875-001

IDE cable, 12.5”, two device (108950-046) 333876-001

* SATA Hard drive cable, use in standard hard drive

position * SA TA Hard drive cable, use in 5 1/4” drive bay only 346144-001 *# DVI graphics cable 285380-001 *#

VGA graphics cable 285379-001 *#

DVI-VGA graphics adapter 202997-001 *

CD-ROM Audio cable (387527-001) 149806-001 *

Antenna cable for 332963-001 and 333864-001 333365-001 *

Flying serial port assembly kit 341899-001

*Not shown #Use with 322892-001, 322893-001, 274623-001, and 274622-001

Miscellaneous Screw Kit (not illustrated)

Miscellaneous screw kit 337237-001 M3 x 5mm, hitop (263585-001) 4 ea #6-32 x .250, hitop (262508-001) 8 ea #6-32 x .250, pan head (101517-037) 3 ea #6-32 x .312, hitop (262508-002) 4 ea #6-19 x .312, pan head (101346-068) 2 ea #6-19 x .315, T15 head (331310-001) 2 ea

Easy Access Keyboards (not illustrated)

PS/2 keyboard for PRC 323686-AA1 Wireless keyboard for PRC 323745-AA1 USB keyboard for PRC 324636-AA1 USB keyboard with SmartCard for PRC 323746-AA1

346141-001

Standard and Optional Boards

PCI extender card 252609-001

System board with alcohol pad and thermal grease 323091-001 Memory Modules * 128 MB/400 MHz FSB * 256 MB/400 MHz FSB * 512 MB/400 MHz FSB * 1.0 GB/400 MHZ FSB * 128 MB/333 MHz FSB * 256 MB/333 MHz FSB * 512 MB/333 MHz FSB * 1.0 GB/333 MHZ FSB Intel Processors with alcohol pad and thermal grease * Celeron 2.0 GHz processor * Celeron 2.2 GHz processor * Celeron 2.3 GHz processor * Celeron 2.4 GHz processor 351495-001 * Celeron 2.5 GHz processor 344056-001 * Celeron 2.6 GHz processor 344057-001 * Pentium 2.4 GHz processor 288689-001 * Pentium 2.53 GHz processor * Pentium 2.66 GHz processor 305579-001 * Pentium 2.8 GHz processor 305051-001 * Pentium 3.0 GHz processor * Pentium 2.4 GHz processor with Hyperthreading * Pentium 2.6 GHz processor with Hyperthreading * Pentium 2.8 GHz processor with Hyperthreading * Pentium 3.0 GHz processor with Hyperthreading * Pentium 3.2 GHz processor with Hyperthreading Other Cards * TPM security module 320163-001 * Broadcom Gigabit NIC 321793-001 * Intel Gigabit NIC * Wireless LAN PCI Adapter , 11 channel (802.11) 332963-001 * Wireless LAN PCI Adapter , 13 channel (802.11) 333364-001 * nVidia GeForce2 MX400, 32 M, ATX bkt 309492-001 * nVidia GeForce4 MX440, 64 M, ATX bkt 322891-001 * nVidia MX400 64 MB, ATX BRACKET 335816-001 * nVidia Quadro4 400 NVS, 64M, ATX bkt 274623-001 * nVidia Quadro4 200 NVS, 32 M, ATX bkt 274622-001 * nVidia Quadro4 100 NVS, 64 M, ATX bkt 322893-001 * nVidia Quadro4 100 NVS, PCI, 64 M, ATX bkt 322892-001 * DVI ADD 4-layer card 325833-001

*Not shown

335697-001 335698-001 335699-001 335700-001 314795-001 314793-001 314796-001 314794-001

309578-001 321723-001 335136-001

333485-001

315637-001 335812-001 333863-001 333864-001 333865-001 335813-001

314901-001

System Board Connectors and Jumpers (position of some untitled components may vary in location)

E49 Password jumper P21 Secondary IDE J20 PCI slot 1 J21 PCI slot 2 P27 Miulti Bay J22 PCI slot 3 P29 SCSI LED J30 PCI slot extender J40 AGP slot P1 Main power (20 pin) P54 Serial Port “B” P3 CPU regulator power (4 pin) P70 CPU fan P5 Front panel P124 Hood lock P6 Internal chassis speaker P125 Hood sensor P7 CD audio in SW50 CMOS button P8 Chassis fan XBT1 Battery P10 Diskette drive XMM1 Memory socket P11 Aux audio in XMM2 Memory socket P14 Boot block XMM3 Memory socket P16 Power supply fan control XMM4 Memory socket P20 Primary IDE

P23 Front audio/USB

P30 Primary Serial ATA (SATA) Port P31 Secondary Serial ATA (SATA) Port

XU100 Security

Keyboard Diagnostic LEDs, PS/2 Keyboards O nly

LED Color LED Activity State/Message

Num, Caps, Scroll Lock

Num Lock Green On ROMPaq diskette not present, is bad, or drive

Caps Lock Green On Enter password. Num, Caps,

Scroll Lock

* Insert valid ROMPaq diskette in drive A. Turn power switch off, then on to reflash ROM. If ROM flash is successful, all three keyboard LEDs will light up, and you will hear a rising tone series of beeps. Remove diskette and turn power off, then on to restart the computer. For more information about flashing the ROM, refer to the Troubleshooting guide.

Clearing CMOS*

The computer's configuration (CMOS) may occasionally be corrupted. If it is, it is necessary to clear the CMOS memory using switch SW50. To clear and reset the configuration, perform the following procedure:

1. Prepare the computer for disassembly.

2. Remove the access panel.

3. Press the CMOS button located on the system board and keep it depressed for 5 seconds.

4. Replace the access panel.

5. Turn the computer on and run F10 Computer Setup (Setup-utility) to reconfigure the system. *When the CMOS button is pushed or the jumper is removed, both the power-on password and the setup password

become invalid because both are stored in the configuration memory. You will need to reset the passwords.

Disabling or Clearing the Power-On and Setup Passwords*

1. Turn off the computer and any external devices, and disconnect the power cord from the power outlet.

2. Remove the access panel.

3. Locate the header and jumper labeled E49.

4. Remove the jumper from pins 1 and 2. Place the jumper over pin 2 only, in order to avoid losing it.

5. Replace the access panel.

6. Plug in the computer and turn on power. Allow the operating system to start. NOTE: Placing the jumper on pin 2 clears the current passwords and disables the password features.

7. To re-enable the password features, repeat steps 1-3, then replace the jumper on pins 1 and 2.

8. Repeat steps 5-6, then establish new passwords.

Refer to the Computer Setup (F10 Setup) instructions to establish new passwords.

*When the CMOS button is pushed or the jumper is removed, both the power-on password and the setup password become invalid because both are stored in the configuration memory. You will need to reset the passwords.

Computer Setup (F10) Utility Features (not all features may be available)

File

Storage

Security

Advanced

Note: See Computer Setup (F10) Utility Guide on the Documentation Library CD.

Interchangeable Heatsinks

Green On (Rising Tone) ROM reflashed successfully

not ready.*

Green Blink On in sequence, one at a

CAUTION: The power cord must be disconnected from the power source before pushing the Clear CMOS Button (NOTE: All LEDs on the board should be OFF). Failure to do so may damage the system board

System Information About Set Time and date

Device Configuration Options

Setup Password Power-On Password Password Options Smart Cover

Power-On Options Onboard devices

time - N, C, SL

Save to Diskette Restore From Diskette Set defaults and Exit

IDE DPS Self-Test Controller Order

Smart Sensor DriveLock Master Boot Record Security Save Master Boot Record

PCI Devices Bus Options

Keyboard locked in network mode

Ignore Changes and Exit Save Changes and Exit

SCSI Narrow Termination Boot Order

Restore Master Boot Record Device Security Network Service Boot System IDs

Devise Options PCI VGA Configuration

PCI Extender Card Connectors and Jumpers

J23 PCI slot 4 P30 Male expansion plug J24 PCI slot 5

System Hardware Interrupts

System Function IRQ System Function

IRQ

Timer Interrupt 8 Real-Time Clock

Keyboard 9 Unused

Interrupt Controller Cascade 10 Unused, available for PCI

Serial Port (COM B) 11 Unused, available for PCI

Serial Port (COM A) 12 Mouse

Unused, available for PCI 13 Coprocessor

Diskette Drive 14 Primary ATA (IDE) Controller

Parallel Port (LPT 1) 15 Secondary ATA (IDE) Controller

Computer Diagnostic LEDs (on front of computer)

LED Color LED Activity State/Message

Power Green On (S0) Computer on Power Green 1 blink every 2 seconds (S1) Suspend Mode Power Green 1 blink every 2 seconds (S3) Suspend to RAM Power Green Off (S4) Suspend to Disk (if applicable) Power Clear Off (S5) Computer off Power Red 1 blink followed by 2-second

Power Red* 2 blinks 1 second apart CPU thermal shutdown Power Red* 3 blinks 1 second apart CPU not installed Power Red* 4 blinks 1 second apart Power supply overload ( crow bar) Power Red* 5 blinks 1 second apart No memory Power Red* 6 blinks 1 second apart No graphics Power Red* 7 blinks 1 second apart System board failure (detected prior to video) Power Red* 8 blinks 1 second apart Invalid ROM Hard Drive Green Blinking Hard drive activity *Blinking codes are repeated after a 2 second pause.

pause - Repeat

Power Supply failure

Heat Sink Removal