HP (Hewlett-Packard) D1D68UA-ABA User Manual

User Guide

© Copyright 2012, 2013 Hewlett-Packard
Development Company, L.P.

Bluetooth is a trademark owned by its
proprietor and used by Hewlett-Packard
Company under license. Intel is a trademark
of Intel Corporation in the U.S. and other
countries. Microsoft and Windows are U.S.
registered trademarks of Microsoft
Corporation. SD Logo is a trademark of its
proprietor.

The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.

Second Edition: February 2013

First Edition: September 2012

Document Part Number: 697167-002

Product notice

This guide describes features that are
common to most models. Some features may
not be available on your computer.

Software terms

By installing, copying, downloading, or
otherwise using any software product
preinstalled on this computer, you agree to
be bound by the terms of the HP End User
License Agreement (EULA). If you do not
accept these license terms, your sole remedy
is to return the entire unused product
(hardware and software) within 14 days for
a refund subject to the refund policy of your
place of purchase.

For any further information or to request a
full refund of the computer, please contact
your local point of sale (the seller).

Safety warning notice

WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not

place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to
come into contact with the skin or a soft surface, such as pillows or rugs or clothing, during operation.
The computer and the AC adapter comply with the user-accessible surface temperature limits defined by
the International Standard for Safety of Information Technology Equipment (IEC 60950).

iii

iv Safety warning notice

Table of contents

1 Starting right .................................................................................................................... 1

Best practices .......................................................................................................................... 1

Fun things to do ....................................................................................................................... 1

More HP resources ................................................................................................................... 2

2 Getting to know your computer ........................................................................................ 4

Finding your hardware and software information ......................................................................... 4

Locating hardware .................................................................................................... 4

Locating software ...................................................................................................... 4

Right side ................................................................................................................................ 4

Left side .................................................................................................................................. 6

Display ................................................................................................................................... 7

Top ........................................................................................................................................ 9

TouchPad ................................................................................................................. 9

Lights ..................................................................................................................... 10

Buttons and speakers ............................................................................................... 11

Keys ...................................................................................................................... 12

Bottom .................................................................................................................................. 13

Labels ................................................................................................................................... 13

3 Connecting to a network ................................................................................................ 15

Connecting to a wireless network ............................................................................................. 15

Using the wireless controls ....................................................................................... 15

Using the wireless button ........................................................................... 15

Using operating system controls ................................................................. 16

Using a WLAN ....................................................................................................... 16

Using an Internet service provider .............................................................. 16

Setting up a WLAN .................................................................................. 17

Configuring a wireless router ..................................................................... 17

Protecting your WLAN .............................................................................. 17

Connecting to a WLAN ............................................................................ 18

Using Bluetooth wireless devices (select models only) ................................................... 18

Connecting to a wired network ................................................................................................ 19

Connecting to a local area network (LAN) .................................................................. 19

v

4 Enjoying entertainment features ..................................................................................... 20

Using the webcam ................................................................................................................. 21

Using audio .......................................................................................................................... 21

Connecting speakers ............................................................................................... 21

Connecting headphones .......................................................................................... 22

Connecting a headset microphone ............................................................................ 22

Checking the sound ................................................................................................. 22

Using video ........................................................................................................................... 22

Connecting an HDMI device ..................................................................................... 24

Configuring HDMI audio settings ............................................................... 24

Using Intel Wireless Display (select models only) ......................................................... 25

Managing your audio and video files ....................................................................................... 25

5 Navigating using touch gestures, pointing devices, and the keyboard ............................ 26

Using the TouchPad ................................................................................................................ 26

Using TouchPad gestures ........................................................................................................ 26

Tapping ................................................................................................................. 27

Scrolling ................................................................................................................ 28

Pinching/zooming ................................................................................................... 28

Edge swipes ........................................................................................................... 29

Right-edge swipe ...................................................................................... 29

Top-edge swipe ....................................................................................... 29

Left-edge swipe ........................................................................................ 30

Using touch screen gestures (select models only) ........................................................................ 30

One-finger slide ...................................................................................................... 31

Tapping ................................................................................................................. 31

Pinch/stretch .......................................................................................................... 32

Edge swipes ........................................................................................................... 33

Right-edge swipe ...................................................................................... 33

Left-edge swipe ........................................................................................ 34

Top-edge swipe and bottom-edge swipe ..................................................... 34

Using the keyboard and mouse ................................................................................................ 35

Using the action keys ............................................................................................... 35

Using Microsoft Windows 8 shortcut keys .................................................................. 36

Using the hot keys ................................................................................................... 37

Using the integrated numeric keypad ......................................................................... 37

6 Managing power ............................................................................................................ 38

Initiating Sleep and Hibernation ............................................................................................... 38

Intel Rapid Start Technology (select models only) ......................................................... 38

vi

Initiating and exiting Sleep ....................................................................................... 39

Enabling and exiting user-initiated Hibernation ........................................................... 39

Setting password protection on wakeup ..................................................................... 39

Using the power meter and power settings ................................................................................ 40

Running on battery power ....................................................................................................... 40

Removing a user-replaceable battery ......................................................................... 40

Installing a user-replaceable battery ........................................................................... 41

Finding battery information ....................................................................................... 41

Conserving battery power ........................................................................................ 42

Identifying low battery levels ..................................................................................... 42

Resolving a low battery level .................................................................................... 42

Resolving a low battery level when external power is available ...................... 42

Resolving a low battery level when no power source is available ................... 42

Resolving a low battery level when the computer cannot exit Hibernation ........ 43

Storing a user-replaceable battery ............................................................................. 43

Disposing of a user-replaceable battery ..................................................................... 43

Replacing a user-replaceable battery ......................................................................... 43

Running on external AC power ................................................................................................ 43

Troubleshooting power problems .............................................................................. 44

HP CoolSense ........................................................................................................................ 44

Refreshing your software content with Intel Smart Connect Technology (select models only) ............. 46

Shutting down (turning off) the computer ................................................................................... 46

7 Managing and sharing information ................................................................................ 47

Using a USB device ................................................................................................................ 47

Connecting a USB device ......................................................................................... 48

Removing a USB device ........................................................................................... 48

Connecting a powered USB device ........................................................................... 48

Inserting and removing a digital storage card ............................................................................ 50

Sharing data and drives and accessing software ....................................................................... 51

8 Maintaining your computer ............................................................................................ 52

Improving performance ........................................................................................................... 52

Using HP 3D DriveGuard ......................................................................................... 52

Using Disk Defragmenter .......................................................................................... 52

Using Disk Cleanup ................................................................................................. 53

Updating programs and drivers ............................................................................................... 53

Cleaning your computer .......................................................................................................... 53

Cleaning the display, sides, and cover ...................................................................... 53

Cleaning the TouchPad and keyboard ....................................................................... 54

Traveling with or shipping your computer .................................................................................. 54

vii

9 Securing your computer and information ........................................................................ 56

Using passwords .................................................................................................................... 56

Setting Windows passwords ..................................................................................... 57

Setting Setup Utility (BIOS) passwords ....................................................................... 57

Using Internet security software ................................................................................................ 58

Using antivirus software ........................................................................................... 58

Using firewall software ............................................................................................ 58

Installing software updates ...................................................................................................... 58

Installing Windows updates ...................................................................................... 59

Installing HP and third-party software updates ............................................................. 59

Securing your wireless network ................................................................................................ 59

Backing up your software applications and information .............................................................. 59

Using an optional security cable lock ........................................................................................ 59

10 Using Setup Utility (BIOS) and System Diagnostics ......................................................... 61

Starting Setup Utility (BIOS) ..................................................................................................... 61

Updating the BIOS ................................................................................................................. 61

Determining the BIOS version ................................................................................... 61

Downloading a BIOS update .................................................................................... 62

Using System Diagnostics ........................................................................................................ 63

11 Backing up, restoring, and recovering .......................................................................... 64

Creating recovery media and backups ..................................................................................... 64

Creating HP Recovery media .................................................................................... 65

Restore and recovery .............................................................................................................. 66

Using Windows Refresh for quick and easy recovery ................................................... 67

Remove everything and reinstall Windows ................................................................. 67

Recovering using HP Recovery Manager .................................................................... 68

What you need to know ............................................................................ 68

Using the HP Recovery partition to recover a minimized image (select models

only) ....................................................................................................... 69

Using HP Recovery media to recover .......................................................... 69

Changing the computer boot order ............................................................. 69

Removing the HP Recovery partition .......................................................................... 70

12 Specifications ................................................................................................................ 71

Input power ........................................................................................................................... 71

Operating environment ........................................................................................................... 71

viii

13 Electrostatic Discharge .................................................................................................. 73

Index ................................................................................................................................. 74

ix

x

1 Starting right

This computer is a powerful tool designed to enhance your work and entertainment. Read this chapter
to learn about best practices after setup, fun things to do with your computer, and where to go to get
more HP resources.

Best practices

To get the most out of your smart investment, after you set up and register the computer, we recommend
the following steps:

Take a minute to browse the printed Windows 8 Basics guide to explore the new Windows®

●

features.

TIP: To quickly return to the computer Start screen from an open app or the Windows desktop,

press the Windows key
the previous screen.

on your keyboard. Pressing the Windows key again will return you to

If you haven’t already done so, connect to a wired or wireless network. See details in

●

to a network on page 15.

Become familiar with the computer hardware and software. Go to

●

on page 4 and Enjoying entertainment features on page 20 for information.

Update or purchase antivirus software. Learn more at

●

Back up your hard drive by creating recovery discs or a recovery flash drive. See

●

restoring, and recovering on page 64.

Fun things to do

You know that you can watch a YouTube video on the computer. But did you know that you can

●

also connect your computer to a TV or gaming console? For more information, see

HDMI device on page 24.

You know you can listen to music you download to the computer. But did you know that you can

●

also stream live radio to the computer and listen to music or talk radio from all over the world?
See

Using audio on page 21.

You know you can create a powerful presentation with Microsoft applications. But did you know

●

you can also connect to a projector to share your ideas with a group? See

on page 22.

Connecting

Getting to know your computer

Using antivirus software on page 58.

Backing up,

Connecting an

Using video

Use the TouchPad and the new Windows 8 touch gestures for smooth control of images and

●

pages of text. See

models only) on page 30.

Using TouchPad gestures on page 26 and Using touch screen gestures (select

Best practices

1

More HP resources

You have already used Setup Instructions to turn on the computer and locate this guide. To locate
product details, how-to information, and more, use this table.

Resource Contents

Setup Instructions

Windows 8 Basics guide

Help and Support

To access Help and Support, from the Start screen, type
h, and then select Help and Support. For U.S.
support, go to
worldwide support, go to

country/us/en/wwcontact_us.html.

Safety & Comfort Guide

To access this guide, from the Start screen, type
support, select the HP Support Assistant app,
select My computer, and then select User guides,
or go to

Worldwide support web page

To get support in your language, go to

http://welcome.hp.com/country/us/en/
wwcontact_us.html.

Regulatory, Safety and Environmental Notices

To access this guide, from the Start screen, type
support, select the HP Support Assistant app,
select My computer, and then select User guides.

http://www.hp.com/go/contactHP. For

http://welcome.hp.com/

http://www.hp.com/ergo.

Overview of computer setup and features.

●

Overview of using and navigating with Windows 8.

●

A broad range of how-to information and troubleshooting tips.

●

Proper workstation setup.

●

Guidelines for posture and work habits that increase your

●

comfort and decrease your risk of injury.

Electrical and mechanical safety information.

●

Online chat with an HP technician.

●

Email support.

●

Find support telephone numbers.

●

Locate HP service center locations.

●

Important regulatory notices, including proper battery disposal

●

information.

2 Chapter 1 Starting right

Resource Contents

Limited Warranty*

To access this guide, from the Start screen, type
support, select the HP Support Assistant app,
select My computer, and then select Warranty
and services, or go to

orderdocuments.

*You can find the expressly provided HP Limited Warranty applicable to your product located with the user guides on your
computer and/or on the CD/DVD provided in the box. In some countries/regions, HP may provide a printed HP Limited
Warranty in the box. For countries/regions where the warranty is not provided in printed format, you may request a printed
copy from

●

●

●

When you request a printed copy of your warranty, please include your product number, warranty period (found on your
service label), name, and postal address.

IMPORTANT: Do NOT return your HP product to the addresses above. For U.S. support, go to

contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html.

http://www.hp.com/go/orderdocuments or write to:

North America: Hewlett-Packard, MS POD, 11311 Chinden Blvd., Boise, ID 83714, USA

Europe, Middle East, Africa: Hewlett-Packard, POD, Via G. Di Vittorio, 9, 20063, Cernusco s/Naviglio (MI), Italy

Asia Pacific: Hewlett-Packard, POD, P.O. Box 200, Alexandra Post Office, Singapore 911507

http://www.hp.com/go/

Specific warranty information about this computer.

●

http://www.hp.com/go/

More HP resources

3

2 Getting to know your computer

Finding your hardware and software information

Locating hardware

To find out what hardware is installed on your computer:

1. From the Start screen, type c, and then select Control Panel.

2. Select System and Security, and then in the System area, select Device Manager.

A list displays all the devices installed in your computer.

Locating software

To find out what software is installed on your computer, from the Start screen, right-click using the

▲

mouse or swipe from the top of the TouchPad or touch screen (select models only) to display the
apps. Select the All apps icon.

Right side

4 Chapter 2 Getting to know your computer

Component Description

(1)

(2)

(3)

Power light

Hard drive light

Digital Media Slot Supports the following digital card formats:

White: The computer is on.

●

Blinking white: The computer is in the Sleep state,

●

which is an energy-saving mode. The computer shuts
off power to the display and other unneeded
components.

Off: The computer is off or in Hibernation. Hibernation

●

is an energy-saving mode that uses the least amount of
power.

NOTE: For select models, the Intel® Rapid Start

Technology feature is enabled at the factory. Rapid
Start Technology allows your computer to resume
quickly from inactivity. For more information, see

Rapid Start Technology (select models only)
on page 38.

Blinking white: The hard drive is being accessed.

●

Amber: HP 3D DriveGuard has temporarily parked the

●

hard drive.

NOTE: For information about HP 3D DriveGuard, see

Using HP 3D DriveGuard on page 52.

Secure Digital (SD) Memory Card

●

Intel

(4)

(5)

(6) RJ-45 (network) jack lights

(7)

USB 3.0 ports (2) Connect optional USB 3.0 devices and provide enhanced

HDMI port Connects an optional video or audio device, such as a high-

RJ-45 (network) jack Connects a network cable.

Secure Digital High Capacity (SDHC) Memory Card

●

Secure Digital Extended Capacity (SDxC) Memory

●

Card

MultiMediaCard (MMC)

●

USB power performance.

NOTE: For details about different types of USB ports, see

Using a USB device on page 47.

definition television, or any compatible digital or audio
device.

White: Computer is connected to a network.

●

Blinking amber: Data is being transferred.

●

NOTE: When both lights are off the computer is not

connected to a network.

Right side

5

Component Description

(8) AC adapter light

(9)

Left side

White: The AC adapter is connected and the battery is

●

charged.

Blinking white: The battery has reached a low battery

●

level.

Amber: The AC adapter is connected and the battery is

●

charging.

Off: The computer is using DC power.

●

Power connector Connects an AC adapter.

Component Description

(1) Security cable slot Attaches an optional security cable to the computer.

NOTE: The security cable is designed to act as a

deterrent, but it may not prevent the computer from being
mishandled or stolen.

(2) Vent Enables airflow to cool internal components.

NOTE: The computer fan starts up automatically to cool

internal components and prevent overheating. It is normal for
the internal fan to cycle on and off during routine operation.

6 Chapter 2 Getting to know your computer

Component Description

(3)

(4)

Display

USB 2.0 port Connects an optional USB 2.0 device.

NOTE: For details about different types of USB ports, see

Using a USB device on page 47.

Audio-out (headphone) jack/Audio-in
(microphone) jack

Produces sound when connected to optional powered stereo
speakers, headphones, earbuds, a headset, or television
audio cable. Also connects an optional headset microphone.
The jack does not support optional microphone-only devices.

WARNING! To reduce the risk of personal injury, adjust

the volume before using headphones, earbuds, or a
headset. For additional safety information, see the
Regulatory, Safety and Environmental Notices.

NOTE: When a device is connected to the jack, the

computer speakers are disabled.

NOTE: Be sure that the device cable has a 4-conductor

connector that supports both audio-out (headphone) and
audio-in (microphone).

Component Description

(1) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless

local area networks (WLANs).

(2) Webcam light On: The webcam is in use.

(3) HP TrueVision HD Webcam Records video, captures still photographs, and allows you to

video conference and chat online using streaming video.

To use the webcam, from the Start screen type c, and then select
CyberLink YouCam.

Display

7

Component Description

(4) Internal microphone Records sound.

*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around
the antennas free from obstructions. For wireless regulatory notices, see the section of the Regulatory, Safety and Environmental

Notices that applies to your country or region. To access this guide, from the Start screen, type support, select the HP
Support Assistant app, select My computer, and then select User guides.

8 Chapter 2 Getting to know your computer

Top

TouchPad

Component Description

(1) TouchPad light

(2) TouchPad on/off button Turns the TouchPad on or off.

(3) TouchPad zone Moves the on-screen pointer and selects or activates items on

(4) Left TouchPad button Functions like the left button on an external mouse.

(5) Right TouchPad button Functions like the right button on an external mouse.

Amber: The TouchPad is off.

●

Off: The TouchPad is on.

●

the screen.

NOTE: The TouchPad also supports edge-swipe gestures.

For more information, see

Edge swipes on page 29.

Top

9

Lights

Component Description

(1)

(2)

(3)

(4) TouchPad light

Power light

Mute light

Wireless light

White: The computer is on.

●

Blinking white: The computer is in the Sleep state, which

●

is an energy-saving mode. The computer shuts off power
to the display and other unneeded components.

Off: The computer is off or in Hibernation. Hibernation

●

is an energy-saving mode that uses the least amount of
power.

For select models, the Intel® Rapid Start Technology
feature is enabled at the factory. Rapid Start Technology
allows your computer to resume quickly from inactivity.
For more information, see

(select models only) on page 38.

Amber: Computer sound is off.

●

Off: Computer sound is on.

●

White: An integrated wireless device, such as a wireless

●

local area network (WLAN) device and/or a
Bluetooth® device, is on.

Amber: All wireless devices are off.

●

Amber: The TouchPad is off.

●

Intel Rapid Start Technology

(5) Caps lock light White: Caps lock is on, which switches the keys to all capital

10 Chapter 2 Getting to know your computer

Off: The TouchPad is on.

●

letters.

Buttons and speakers

Component Description

(1)

Power button

When the computer is off, press the button to turn on

●

the computer.

When the computer is in the Sleep state, press the

●

button briefly to exit Sleep.

When the computer is in Hibernation, press the button

●

down briefly to exit Hibernation.

CAUTION: Pressing and holding down the power button

will result in the loss of unsaved information.

If the computer has stopped responding and Windows
shutdown procedures are ineffective, press and hold the
power button down for at least 5 seconds to turn off the
computer.

NOTE: For select models, the Intel Rapid Start Technology

feature is enabled at the factory. Rapid Start Technology
allows your computer to resume quickly from inactivity. For
more information, see

models only) on page 38

To learn more about your power settings:

1. From the Start screen, type power.

2. Select Settings, and then select Power Options, or

see

Managing power on page 38.

Intel Rapid Start Technology (select

(2) Speakers (2) Produce sound.

Top

11

Keys

Component Description

(1) esc key Displays system information when pressed in combination

with the fn key.

(2) fn key Displays system information when pressed in combination

with the esc key.

(3)

(4) Action keys Execute frequently used system functions.

(5)

(6) num lock key Controls the function of the integrated numeric keypad. Press

(7) Integrated numeric keypad Set at the factory to function like an external numeric

Windows logo key Returns you to the Start screen from an open app or the

Desktop.

NOTE: Pressing the Windows logo key again will return

you to the previous screen.

Windows applications key Displays options for a selected object.

the key to alternate between the standard numeric function
of an external keypad (selected the factory) and the
navigational function (indicated by the directional arrows on
the keys).

NOTE: The keypad function that is active when the

computer is turned off is reinstated when the computer is
turned back on.

keypad. To alternate between this numeric function and the
navigational function (indicated by the directional arrows on
the keys), press the num lock key.

12 Chapter 2 Getting to know your computer

Bottom

Component Description

(1) Battery bay Holds the battery.

(2)

(3) Vents (4) Enable airflow to cool internal components.

(4)

Labels

The labels affixed to the computer provide information you may need when you troubleshoot system
problems or travel internationally with the computer. The labels are in easily accessible locations.

●

Battery lock Locks and unlocks the battery.

NOTE: The computer fan starts up automatically to cool

internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.

Battery release latch Releases the battery from the battery bay.

Service label—Provides important information, including the following:

NOTE: Your label may look slightly different from the illustration in this section.

Bottom

13

Component

(1) Product name

(2) Serial number

(3) Product number

(4) Warranty period

(5) Model description (select models only)

Have this information available when you contact support. The service label is located on the
bottom of your computer.

Regulatory label—Provides regulatory information about the computer. The regulatory label is

●

located on the bottom of your computer.

Wireless certification label or labels—Provide information about wireless devices and the

●

approval markings of some of the countries or regions in which the devices have been approved
for use. Your computer model includes one or more wireless devices; one or more certification
labels are included with your computer. You may need this information when traveling
internationally. Wireless certification labels are located on the bottom of your computer.

14 Chapter 2 Getting to know your computer

3 Connecting to a network

Your computer can travel with you wherever you go. But even at home, you can explore the globe and
access information from millions of websites using your computer and a wired or wireless network
connection. This chapter will help you get connected to that world.

Connecting to a wireless network

Wireless technology transfers data across radio waves instead of wires. Your computer may be
equipped with one or more of the following wireless devices:

Wireless local area network (WLAN) device—Connects the computer to wireless local area

●

networks (commonly referred to as Wi-Fi networks, wireless LANs, or WLANs) in corporate
offices, your home, and public places such as airports, restaurants, coffee shops, hotels, and
universities. In a WLAN, the mobile wireless device in your computer communicates with a
wireless router or a wireless access point.

Bluetooth device (select models only)—Creates a personal area network (PAN) to connect to other

●

Bluetooth-enabled devices such as computers, phones, printers, headsets, speakers, and cameras.
In a PAN, each device communicates directly with other devices, and devices must be relatively
close together—typically within 10 meters (approximately 33 feet) of each other.

For more information about wireless technology, see the information and website links provided in Help
and Support. From the Start screen, type h, and then select Help and Support.

Using the wireless controls

You can control the wireless devices in your computer using these features:

Wireless button, wireless switch, or wireless key (referred to in this chapter as the wireless button)

●

Operating system controls

●

Using the wireless button

Your computer has a wireless button, one or more wireless devices, and one wireless light. All of the
wireless devices on your computer are enabled at the factory, so the wireless light is on (white) when
you turn on the computer.

The wireless light indicates the overall power state of your wireless devices, not the status of individual
devices. If the wireless light is white, at least one wireless device is on. If the wireless light is amber, all
wireless devices are off.

Because the wireless devices are enabled at the factory, you can use the wireless button to turn on or
turn off the wireless devices simultaneously.

Connecting to a wireless network

15

Using operating system controls

The Network and Sharing Center allows you to set up a connection or network, connect to a network,
manage wireless networks, and diagnose and repair network problems.

To use operating system controls:

1. From the Start screen, type n, and then select Settings.

2. Type network and sharing in the search box, and then select Network and Sharing

Center.

For more information, from the Start screen, type h, and then select Help and Support.

Using a WLAN

With a WLAN device, you can access a wireless local area network (WLAN), which is composed of
other computers and accessories that are linked by a wireless router or a wireless access point.

NOTE: The terms wireless router and wireless access point are often used interchangeably.

A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points

●

that can accommodate a large number of computers and accessories and can separate critical
network functions.

A home or small office WLAN typically uses a wireless router, which allows several wireless and

●

wired computers to share an Internet connection, a printer, and files without requiring additional
pieces of hardware or software.

To use the WLAN device in your computer, you must connect to a WLAN infrastructure (provided
through a service provider or a public or corporate network).

Using an Internet service provider

When you are setting up Internet access in your home, you must establish an account with an Internet
service provider (ISP). To purchase Internet service and a modem, contact a local ISP. The ISP will help
set up the modem, install a network cable to connect your wireless router to the modem, and test the
Internet service.

NOTE: Your ISP will give you a user ID and a password to use for Internet access. Record this

information and store it in a safe place.

16 Chapter 3 Connecting to a network

Setting up a WLAN

To set up a WLAN and connect to the Internet, you need the following equipment:

A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an

●

Internet service provider

A wireless router (2) (purchased separately)

●

A wireless computer (3)

●

NOTE: Some modems have a built-in wireless router. Check with your ISP to determine what type of

modem you have.

The illustration below shows an example of a wireless network installation that is connected to the
Internet.

As your network grows, additional wireless and wired computers can be connected to the network to
access the Internet.

For help in setting up your WLAN, see the information provided by your router manufacturer or your
ISP.

Configuring a wireless router

For help in setting up a WLAN, see the information provided by your router manufacturer or your ISP.

NOTE: It is recommended that you initially connect your new wireless computer to the router by using

the network cable provided with the router. When the computer successfully connects to the Internet,
disconnect the cable, and access the Internet through your wireless network.

Protecting your WLAN

When you set up a WLAN or access an existing WLAN, always enable security features to protect
your network from unauthorized access. WLANs in public areas (hotspots) like coffee shops and
airports may not provide any security. If you are concerned about the security of your computer when
connected to a hotspot, limit your network activities to email that is not confidential and basic Internet
surfing.

Wireless radio signals travel outside the network, so other WLAN devices can pick up unprotected
signals. Take the following precautions to protect your WLAN:

Use a firewall.

●

A firewall checks both data and requests for data that are sent to your network, and discards any
suspicious items. Firewalls are available in both software and hardware. Some networks use a
combination of both types.

Use wireless encryption.

●

Connecting to a wireless network

17

Wireless encryption uses security settings to encrypt and decrypt data that is transmitted over the
network. For more information, from the Start screen, type h, and then select Help and

Support.

Connecting to a WLAN

To connect to a WLAN, follow these steps:

1. Be sure that the WLAN device is on. If the device is on, the wireless light is on (white). If the

wireless light is amber, press the wireless button.

2. From the Desktop, tap or click the network status icon in the notification area, at the far right of the

taskbar.

3. Select your WLAN from the list.

4. Select Next.

If the WLAN is a security-enabled WLAN, you are prompted to enter a security code. Type the
code, and then select OK to complete the connection.

NOTE: If no WLANs are listed, you may be out of range of a wireless router or access point.

NOTE: If you do not see the WLAN you want to connect to, from the Desktop, right-click the

network status icon. On models with a touch screen, press and hold the network status icon. Then
select Open Network and Sharing Center. Select Set up a new connection or
network. A list of options is displayed, allowing you to manually search for and connect to a
network or to create a new network connection.

5. Follow the on-screen instructions to complete the connection.

After the connection is made, place the mouse pointer over the network status icon in the notification
area, at the far right of the Desktop taskbar, to verify the name and status of the connection.

NOTE: The functional range (how far your wireless signals travel) depends on WLAN

implementation, router manufacturer, and interference from other electronic devices or structural
barriers such as walls and floors.

Using Bluetooth wireless devices (select models only)

A Bluetooth device provides short-range wireless communications that replace the physical cable
connections that traditionally link electronic devices such as the following:

Computers (desktop, notebook, PDA)

●

Phones (cellular, cordless, smart phone)

●

Imaging devices (printer, camera)

●

Audio devices (headset, speakers)

●

Mouse

●

Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network
(PAN) of Bluetooth devices. For information about configuring and using Bluetooth devices, see the
Bluetooth software Help.

18 Chapter 3 Connecting to a network

Connecting to a wired network

Your computer supports a local area network (LAN) wired connection. A LAN connection uses a
network cable and is much faster than a modem connection, which uses a telephone cable. Both cables
are sold separately.

WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a

modem cable or telephone cable into an RJ-45 (network) jack.

Connecting to a local area network (LAN)

Use a LAN connection if you want to connect the computer directly to a router in your home (instead of
working wirelessly), or if you want to connect to an existing network at your office.

Connecting to a LAN requires an 8-pin, RJ-45 (network) cable.

To connect the network cable, follow these steps:

1. Plug the network cable into the network jack (1) on the computer.

2. Plug the other end of the network cable into a network wall jack (2) or router.

NOTE: If the network cable contains noise suppression circuitry (3), which prevents interference

from TV and radio reception, orient the circuitry end of the cable toward the computer.

Connecting to a wired network

19

4 Enjoying entertainment features

Use your HP computer as an entertainment hub to socialize via the webcam, enjoy and manage your
music, and download and watch movies. Or, to make your computer an even more powerful
entertainment center, connect external devices like a monitor, projector, or TV, or speakers and
headphones.

Here are some of the entertainment features on your computer.

Component Description

(1) Webcam light On: The webcam is in use.

(2) HP TrueVision HD Webcam Records video, captures still photographs, and allows

(3) Internal microphone Records sound.

(4)

HDMI port Connects an optional video or audio device, such as

20 Chapter 4 Enjoying entertainment features

you to video conference and chat online using
streaming video.

To use the webcam, from the Start screen, type c,
and then select CyberLink YouCam.

a high-definition television, any compatible digital or
audio component, or a high-speed HDMI device.

Component Description

(5)

(6) Speakers (2) Produce sound.

(7)

(8)

USB 3.0 ports (2) Connect optional USB 3.0 devices and provide

enhanced USB power performance.

NOTE: For details about different types of USB

ports, see

Audio-out (headphone) jack/Audio-in
(microphone) jack

USB 2.0 port Connects an optional USB 2.0 device.

Produces sound when connected to optional powered
stereo speakers, headphones, earbuds, a headset, or
television audio cable. Also connects an optional
headset microphone. This jack does not support
optional microphone-only devices.

WARNING! To reduce the risk of personal injury,

adjust the volume before putting on headphones,
earbuds, or a headset. For additional safety
information, refer to the Regulatory, Safety and
Environmental Notices.

NOTE: When a device is connected to the jack, the

computer speakers are disabled.

NOTE: Be sure that the device cable has a 4-

conductor connector that supports both audio-out
(headphone) and audio-in (microphone).

NOTE: For details about different types of USB

ports, see Using a USB device on page 47.

Using a USB device on page 47.

Using the webcam

Your computer has an integrated webcam, a powerful social networking tool that allows you to
communicate up close with friends and colleagues, next door or on the other side of the world. With
the webcam, you can stream video with your instant messaging software, capture and share video,
and take still photos.

To start the webcam, from the Start screen, type c, and then select CyberLink YouCam from the

▲

list of applications.

For details about using the webcam, refer to the help for the app.

Using audio

On your HP computer, you can download and listen to music, stream audio content from the web
(including radio), record audio, or mix audio and video to create multimedia. To enhance your
listening enjoyment, attach external audio devices such as speakers or headphones.

Connecting speakers

You can attach wired speakers to your computer by connecting them to a USB port (or the audio-out
jack/audio-in jack) on your computer or on a docking station.

Using the webcam

21

To connect wireless speakers to your computer, follow the device manufacturer's instructions. To
connect high-definition speakers to the computer, see
Before connecting speakers, lower the volume setting.

Connecting headphones

You can connect wired headphones to the audio-out jack/audio-in jack on your computer.

To connect wireless headphones to your computer, follow the device manufacturer's instructions.

WARNING! To reduce the risk of personal injury, lower the volume setting before putting on

headphones, earbuds, or a headset. For additional safety information, see the Regulatory, Safety and
Environmental Notices.

Connecting a headset microphone

To record audio, connect a headset microphone to the audio-out jack/audio-in jack on the computer.
For best results when recording, speak directly into the headset microphone and record sound in a
setting free of background noise.

Checking the sound

To check the audio functions on your computer, follow these steps:

Configuring HDMI audio settings on page 24.

1. From the Start screen, type c, and then select Control Panel from the list of applications.

2. Select Hardware and Sound, and then select Sound.

3. When the Sound window opens, select the Sounds tab. Under Program Events, select any

sound event, such as a beep or alarm, and then select Test.

You should hear sound through the speakers or through connected headphones.

To check the recording functions on your computer, follow these steps:

1. From the Start screen, type s, and then select Sound Recorder.

2. Select Start Recording and speak into the microphone. Save the file to your Desktop.

3. Open a multimedia program and play the recording.

To confirm or change the audio settings on your computer:

1. From the Start screen, type c, and then select Control Panel from the list of applications.

2. Select Hardware and Sound, and then select Sound.

Using video

Your HP computer is a powerful video device that enables you to watch streaming video from your
favorite websites and download video and movies to watch on your computer without needing to
connect to a network.

To enhance your viewing enjoyment, use the video port on the computer to connect an external
monitor, projector, or TV. Your computer has a high-definition multimedia interface (HDMI) port, which
allows you to connect a high-definition monitor or TV.

22 Chapter 4 Enjoying entertainment features

IMPORTANT: Be sure that the external device is connected to the correct port on the computer,

using the correct cable. Check the device manufacturer's instructions.

Using video

23

Connecting an HDMI device

NOTE: To connect an HDMI device to your computer, you need an HDMI cable, sold separately.

To see the computer screen image on a high-definition TV or monitor, connect the high-definition device
according to the following instructions.

1. Connect one end of the HDMI cable to the HDMI port on the computer.

2. Connect the other end of the cable to the high-definition TV or monitor.

3. Press f4 to alternate the computer screen image between 4 display states:

PC screen only: View the screen image on the computer only.

●

Duplicate: View the screen image simultaneously on both the computer and external device.

●

Extend: View the screen image extended across both the computer and external device.

●

Second screen only: View the screen image on the external device only.

●

Each time you press f4, the display state changes.

NOTE: Adjust the screen resolution of the external device, especially if you choose the “Extend”

option. From the Start screen, type c, and then select Control Panel from the list of applications.
Select Appearance and Personalization. Under Display, select Adjust screen

resolution for best results.

Configuring HDMI audio settings

HDMI is the only video interface that supports high-definition video and audio. After you connect an
HDMI TV to the computer, you can then turn on HDMI audio by following these steps:

1. From the Windows desktop, right-click the Speakers icon in the notification area, at the far right

of the taskbar. On models with a touch screen, press and hold the Speakers icon.

2. Select Playback devices.

3. On the Playback tab, select the name of the digital output device.

4. Select Set Default, and then select OK.

24 Chapter 4 Enjoying entertainment features

To return the audio stream to the computer speakers:

1. From the Windows desktop, right-click the Speakers icon in the notification area, at the far right

of the taskbar. On models with a touch screen, press and hold the Speakers icon.

2. Select Playback devices.

3. On the Playback tab, select Speakers and Headphones.

4. Select Set Default, and then select OK.

Using Intel Wireless Display (select models only)

Intel® Wireless Display allows you to transmit your computer content wirelessly to your receive/display
device, such as HDTV, monitor, projector, game console, Blu-ray player, or DVR, by using an optional
wireless adapter (purchased separately). For details about using the wireless adapter, see the
manufacturer's instructions.

To open Intel Wireless Display, from the Start screen, type w, and then select Intel WiDi.

▲

NOTE: Before using the wireless display feature, be sure that your wireless device is turned on.

Managing your audio and video files

CyberLink PowerDVD (select models only) helps you manage and edit your audio and video
collections.

To open CyberLink PowerDVD, from the Start screen, type c, and then select CyberLink

▲

PowerDVD.

For more information about using CyberLink PowerDVD, see the PowerDVD software Help.

Managing your audio and video files

25

5 Navigating using touch gestures,

pointing devices, and the keyboard

Your computer allows navigation using touch gestures in addition to the keyboard and mouse. Touch
gestures can be used on your computer TouchPad or on a touch screen (select models only).

NOTE: An external USB mouse (purchased separately) can be connected to one of the USB ports on

the computer.

Review the Windows 8 Basics guide included with your computer. The guide provides information on
how to perform common tasks using the TouchPad, touch screen, or the keyboard.

Your computer also has special action keys or hot key functions on the keyboard to perform routine
tasks.

Using the TouchPad

The TouchPad, allows you to navigate the computer with simple finger movements.

You can customize the touch gestures by changing settings, button configurations, click speed, and
pointer options. From the Start screen type c to display the Apps list. Select Control Panel, and then
select Hardware and Sound. Under Devices and Printers, select Mouse.

Turning the TouchPad off or on

To turn the TouchPad off or on, quickly double-tap the TouchPad on/off button.

The TouchPad light is off when the TouchPad is on.

The TouchPad supports a variety of gestures that let your fingers scroll, swipe, pinch, and rotate to
manipulate items on the screen.

Using TouchPad gestures

A TouchPad allows you to control the pointer on the screen using your fingers.

TIP: Use the left and right buttons on the TouchPad as you would use the corresponding buttons on an

external mouse.

26 Chapter 5 Navigating using touch gestures, pointing devices, and the keyboard

NOTE: TouchPad gestures are not supported in all programs.

To view a demonstration of each gesture:

1. From the Start screen, type c to display the Apps list. Select Control Panel, and then select

2. Select Synaptics TouchPad.

3. Click a gesture to activate the demonstration.

To turn the gestures off or on:

1. From the Synaptics TouchPad screen, select or clear the check box next to the gesture that you

2. Click Apply, and then click OK.

Tapping

To make an on-screen selection use the tap function on the TouchPad.

●

NOTE: Press and hold your finger on the TouchPad to open a help screen that provides information

about the selected item.

Hardware and Sound.

want to turn on or off.

Point to an item on the screen, and then tap one finger on the TouchPad zone to make a selection.
Double-tap an item to open it.

Using TouchPad gestures

27

Scrolling

Scrolling is useful for moving up, down, or sideways on a page or image.

●

Place two fingers slightly apart on the TouchPad zone and then drag them up, down, left, or right.

Pinching/zooming

Pinching and zooming allow you to zoom out or in on images or text.

Zoom in by placing two fingers together on the TouchPad zone and then moving your fingers

●

apart.

Zoom out by placing two fingers apart on the TouchPad zone and then moving your fingers

●

together.

28 Chapter 5 Navigating using touch gestures, pointing devices, and the keyboard

Edge swipes

Edge swipes allow you to perform tasks such as changing settings and finding or using apps.

Right-edge swipe

The right-edge swipe reveals the charms, which let you search, share, start apps, access devices, or
change settings.

Swipe your finger gently from the right edge to display the charms.

●

Top-edge swipe

The top-edge swipe allows you to access All Apps available on the Start screen.

IMPORTANT: When an app is active, the top-edge gesture varies depending on the app.

Swipe your finger gently from the top edge to display available apps.

●

Using TouchPad gestures

29

Left-edge swipe

The left-edge swipe reveals your open apps so that you can switch to them quickly.

Swipe your finger gently from the left edge of the TouchPad to switch between apps.

●

Using touch screen gestures (select models only)

A touch screen computer allows you to control items on the screen directly with your fingers.

TIP: On touch screen computers, you can perform the gestures on the screen or on the TouchPad. You

can also perform on-screen actions with the keyboard and mouse.

30 Chapter 5 Navigating using touch gestures, pointing devices, and the keyboard

One-finger slide

The one-finger slide is mostly used to pan or scroll through lists and pages, but you can use it for other
interactions, too, such as moving an object.

To scroll across the screen, lightly slide one finger across the screen in the direction you want to

●

move.

NOTE: When many apps are displayed on the Start screen, you can slide your finger to move

the screen left or right.

To drag, press and hold an object, and then drag the object to move it.

●

Tapping

To make an on-screen selection, use the tap function.

●

Use one finger to tap an object on the screen to make a selection. Double-tap an item to open it.

NOTE: Press and hold your finger on an object to open a help screen that provides information

about the object. Press and hold provides the same information as using a mouse to right-click an
object.

Using touch screen gestures (select models only)

31

Pinch/stretch

Pinching and stretching allows you to zoom out or in on images or text.

Zoom in by placing two fingers together on the display and then move your fingers apart.

●

Zoom out by placing two fingers apart on the display and then move your fingers together.

●

32 Chapter 5 Navigating using touch gestures, pointing devices, and the keyboard

Edge swipes

With edge swipes you can perform tasks such as changing settings and finding or using apps.

Right-edge swipe

The right-edge swipe reveals the charms, which let you search, share, start apps, access devices, or
change settings.

Gently swipe your finger inward from the right edge of the display bezel onto the screen to

●

display the charms.

Using touch screen gestures (select models only)

33

Left-edge swipe

The left-edge swipe accesses your recently opened apps so that you can switch between them quickly.

Gently swipe your finger inward from the left edge of the display bezel to switch between recently

●

opened apps.

Without lifting your finger, swipe back toward the left edge to display all recently opened apps.

●

Top-edge swipe and bottom-edge swipe

The top-edge swipe or bottom-edge swipe allows you to open a list of apps available on your
computer.

1. Gently swipe your finger from the top edge or the bottom edge of the display bezel onto the

screen.

34 Chapter 5 Navigating using touch gestures, pointing devices, and the keyboard

2. Tap All apps to view available apps.

Using the keyboard and mouse

The keyboard and mouse allow you to type, select items, scroll and to perform the same functions as
you do by using touch gestures. The keyboard also allows you to use action keys and hot keys to
perform specific functions.

TIP: The Windows key on the keyboard allows you to quickly return to the Start screen from an

open app or the Desktop. Pressing the Windows key again will return you to the previous screen.

NOTE: Depending on the country or region, your keyboard may have different keys and keyboard

functions than those discussed in this section.

Using the action keys

An action key performs an assigned function. The icon on each of the f1 through f4 keys and f6
through f12 keys illustrates the assigned function for that key.

To use an action key function, press and hold the key.

The action key feature is enabled at the factory. You can disable this feature in Setup Utility (BIOS). See

Using Setup Utility (BIOS) and System Diagnostics on page 61 for instructions on opening Setup

Utility (BIOS), and then follow the instructions at the bottom of the screen.

To activate the assigned function after you have disabled the action key feature, you must press the fn
key in combination with the appropriate action key.

CAUTION: Use extreme care when making changes in Setup Utility. Errors can prevent the computer

from operating properly.

Using the keyboard and mouse

35

Icon Key Description

f1 Opens Help and Support, which provides tutorials, information about the Windows

operating system and your computer, answers to questions, and updates to your
computer.

Help and Support also provides automated troubleshooting tools and access to support.

f2 Decreases the screen brightness incrementally as long as you hold down the key.

f3 Increases the screen brightness incrementally as long as you hold down the key.

f4 Switches the screen image between display devices connected to the system. For

example, if a monitor is connected to the computer, pressing this key alternates the
screen image from the computer display to the monitor display to a simultaneous
display on both the computer and the monitor.

Most external monitors receive video information from the computer using the external
VGA video standard. This action key can also alternate images among other devices
that are receiving video information from the computer.

f6 Plays the previous track of an audio CD or the previous section of a DVD or a BD.

f7 Begins, pauses, or resumes playback of an audio CD, a DVD, or a BD.

f8 Plays the next track of an audio CD or the next section of a DVD or a BD.

f9 Decreases speaker volume incrementally as long as you hold down the key.

f10 Increases speaker volume incrementally as long as you hold down the key.

f11 Mutes or restores speaker sound.

f12 Turns the wireless feature on or off.

NOTE: A wireless network must be set up before a wireless connection is possible.

Using Microsoft Windows 8 shortcut keys

Microsoft Windows 8 provides shortcuts to perform actions quickly. Several shortcuts will help you with
Windows 8 functions. Press the Windows logo key in combination with the key to perform the
action.

For additional information on Windows 8 shortcut keys, go to Help and Support. From the Start
screen, type h, and then select Help and Support.

36 Chapter 5 Navigating using touch gestures, pointing devices, and the keyboard

Shortcut Keys

Shortcut
key

alt + f4 Closes an active app.

Key Description

Returns you to the Start screen from an open app or the Desktop.

+ c Opens the charms.

+ d Opens the Desktop.

+ tab Switches between open apps.

Using the hot keys

A hot key is a combination of the fn key and the esc key.

To use a hot key:

Briefly press the fn key, and then briefly press the second key of the combination.

▲

Pressing the key again returns you to the previous screen.

NOTE: Continue to press this key combination until the app you

want displays.

Function Hot key Description

Display system information. fn+esc Displays information about system hardware components and the

system BIOS version number.

Using the integrated numeric keypad

The computer includes an integrated numeric keypad, and it also supports an optional external numeric
keypad or an optional external keyboard that includes a numeric keypad.

Component Description

num lock key Controls the function of the integrated numeric keypad. Press the

key to alternate between the standard numeric function found on
an external keypad (this function is turned on at the factory) and
the navigational function (indicated by the directional arrows on
the keys).

NOTE: The keypad function that is active when the computer is

turned off is reinstated when the computer is turned back on.

Integrated numeric keypad Set at the factory to function like an external numeric keypad. To

alternate between this numeric function and the navigational
function (indicated by the directional arrows on the keys), press
the num lock key.

Using the keyboard and mouse

37

6 Managing power

Your computer can operate on either battery power or external power. When the computer is only
running on battery power and an AC power source is not available to charge the battery, it is
important to monitor and conserve the battery charge. Your computer supports power plans to manage
how your computer uses and conserves power so that you can balance computer performance with
power conservation.

Initiating Sleep and Hibernation

Windows has two power-saving states, Sleep and Hibernation.

Sleep–The Sleep state is automatically initiated after a period of inactivity when running on battery

●

power or on external power. Your work is saved to memory, allowing you to resume your work
very quickly. You can also initiate Sleep manually. For more information, see

Sleep on page 39.

Hibernation–The Hibernation state is automatically initiated if the battery reaches a critical level. In

●

the Hibernation state, your work is saved to a hibernation file and the computer powers down.

NOTE: If you want to initiate Hibernation manually, you must enable Hibernation using Power

Options. For more information, see

Enabling and exiting user-initiated Hibernation on page 39.

Initiating and exiting

CAUTION: To reduce the risk of possible audio and video degradation, loss of audio or video

playback functionality, or loss of information, do not initiate Sleep while reading from or writing to a
disc or an external media card.

NOTE: You cannot initiate any type of networking connection or perform any computer functions

while the computer is in the Sleep state or in Hibernation.

Intel Rapid Start Technology (select models only)

For select models, the Intel Rapid Start Technology (RST) feature is enabled by default. Rapid Start
Technology allows your computer to resume quickly from inactivity.

Rapid Start Technology manages your power-saving options as follows:

Sleep—Rapid Start Technology allows you to select the Sleep state. To exit from Sleep, press any

●

key, activate the TouchPad, or press the power button briefly.

Hibernation—Rapid Start Technology initiates Hibernation after a period of inactivity while in the

●

Sleep state when running on battery power or on external power or when the battery reaches a
critical level. After Hibernation is initiated, press the power button to resume your work.

NOTE: Rapid Start Technology can be disabled in Setup Utility (BIOS). If you want to be able to

initiate the Hibernation state, you must enable user-initiated Hibernation using Power Options. See

Enabling and exiting user-initiated Hibernation on page 39.

38 Chapter 6 Managing power

Initiating and exiting Sleep

With the computer on, you can initiate Sleep in any of the following ways:

Close the display.

●

From the Start screen, point to the upper-right or lower-right corner of the screen. When the

●

charms list opens, select Settings, select the Power icon, and then select Sleep.

To exit Sleep:

Briefly press the power button.

●

If the display is closed, open the display.

●

Press a key on the keyboard.

●

Tap or swipe the TouchPad.

●

When the computer exits Sleep, the power lights turn on and the computer returns to the screen where
you stopped working.

NOTE: If you have set a password to be required on wakeup, you must enter your Windows

password before the computer will return to the screen.

Enabling and exiting user-initiated Hibernation

You can enable user-initiated Hibernation and change other power settings and timeouts using Power
Options:

1. From the Start screen, type power, select Settings, and then select Power Options from the list

of applications.

2. In the left pane, select Choose what the power button does.

3. Select Change Settings that are currently unavailable.

4. In the When I press the power button area, select Hibernate.

5. Select Save changes.

To exit Hibernation, briefly press the power button. The power lights turn on and your work returns to
the screen where you stopped working.

NOTE: If you have set a password to be required on wakeup, you must enter your Windows

password before your work will return to the screen.

Setting password protection on wakeup

To set the computer to prompt for a password when the computer exits Sleep or Hibernation, follow
these steps:

1. From the Start screen, type power, select Settings, and then select Power Options.

2. In the left pane, select Require a password on wakeup.

3. Select Change Settings that are currently unavailable.

Initiating Sleep and Hibernation

39

4. Select Require a password (recommended).

NOTE: If you need to create a user account password or change your current user account

password, select Create or change your user account password, and then follow the on­screen instructions. If you do not need to create or change a user account password, go to step 5.

5. Select Save changes.

Using the power meter and power settings

The power meter is located on the Windows desktop. The power meter allows you to quickly access
power settings and view the remaining battery charge.

To display the percentage of remaining battery charge and the current power plan, on the

●

Windows Desktop, point over the power meter icon.

To use Power Options, or to change the power plan, click or tap the power meter icon and select

●

an item from the list. From the Start screen, you can also type power, select Settings, and then
select Power Options.

Different power meter icons indicate whether the computer is running on battery or external power. The
icon also displays a message if the battery has reached a low or critical battery level.

Running on battery power

When a charged battery is in the computer and the computer is not plugged into external power, the
computer runs on battery power. If the computer has a charged battery installed and the AC adapter is
disconnected from the computer, the computer automatically switches to battery power and the display
brightness decreases to conserve battery life. The battery in the computer slowly discharges when the
computer is off and unplugged from external power.

Computer battery life varies, depending on power management settings, programs running on the
computer, display brightness, external devices connected to the computer, and other factors.

Removing a user-replaceable battery

WARNING! To reduce potential safety issues, use only the user-replaceable battery provided with

the computer, a replacement battery provided by HP, or a compatible battery purchased from HP.

CAUTION: Removing a user-replaceable battery that is the sole power source for the computer can

cause loss of information. To prevent loss of information, save your work or shut down the computer
through Windows before removing the battery.

To remove the battery:

1. Turn the computer upside down on a flat surface.

2. Slide the battery lock (1) to unlock the battery.

3. Slide the battery release latch (2) to release the battery.

40 Chapter 6 Managing power

4. Slide the battery (3) from the middle to remove it from the computer.

NOTE: The battery release latch automatically returns to its original position. The battery lock will

remain in the unlocked position.

Installing a user-replaceable battery

To install the battery, follow these steps:

CAUTION: Do not slant the battery as you insert it.

1. Holding the battery in the middle, slide the battery (1) straight into the computer until the battery

release latch locks into place.

2. Reset the battery lock (2) to the locked position.

Finding battery information

To monitor the status of your battery, or if the battery is no longer holding a charge, run Battery Check
in HP Support Assistant. To access battery information, from the Start screen, type support, select the
HP Support Assistant app, and then select Battery and performance.

Running on battery power

41

HP Support Assistant provides the following tools and information about the battery:

Battery test

●

Information on battery types, specifications, life cycles, and capacity

●

Conserving battery power

Tips for conserving battery power and maximizing battery life:

Lower the brightness on the display.

●

Select the Power saver setting in Power Options.

●

Remove the user-replaceable battery from the computer when it is not being used or charged.

●

Turn off wireless devices when you are not using them.

●

Disconnect unused external devices that are not plugged into an external power source, such as

●

an external hard drive connected to a USB port.

Stop, disable, or remove any external media cards that you are not using.

●

Before you leave your work, initiate Sleep or shut down the computer.

●

Identifying low battery levels

When a battery that is the sole power source for the computer reaches a low or critical battery level,
the power meter icon on the Windows desktop shows a low or critical battery notification.

NOTE: For additional information about the power meter, refer to Using the power meter and power

settings on page 40.

The computer takes the following actions for a critical battery level:

If Hibernation is disabled and the computer is on or in the Sleep state, the computer remains

●

briefly in the Sleep state, and then shuts down and loses any unsaved information.

If Hibernation is enabled and the computer is on or in the Sleep state, the computer initiates

●

Hibernation.

Resolving a low battery level

Resolving a low battery level when external power is available

Connect an AC adapter.

●

Connect an optional docking or expansion device.

●

Connect an optional power adapter purchased as an accessory from HP.

●

Resolving a low battery level when no power source is available

Save your work and shut down the computer.

42 Chapter 6 Managing power

Resolving a low battery level when the computer cannot exit Hibernation

When the computer lacks sufficient power to exit Hibernation, follow these steps:

1. Replace the discharged user-replaceable battery with a charged battery, or connect the AC

adapter to the computer and to external power.

2. Exit Hibernation by pressing the power button.

Storing a user-replaceable battery

CAUTION: To reduce the risk of damage to a battery, do not expose it to high temperatures for

extended periods of time.

If your computer will be unused and unplugged from external power for more than 2 weeks, remove the
battery and store it separately in a cool, dry place to prolong the battery charge.

A stored battery should be checked every 6 months. If the capacity is less than 50 percent, recharge
the battery before returning it to storage.

Disposing of a user-replaceable battery

WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short

external contacts; do not dispose of in fire or water.

See the Regulatory, Safety and Environmental Notices for proper battery disposal. To access the user
guides, from the Start screen, type support, select the HP Support Assistant app, select My

computer, and then select the User guides.

Replacing a user-replaceable battery

Battery Check in HP Support Assistant notifies you to replace the battery when an internal cell is not
charging properly or when the battery storage capacity has reached a weak condition. If the battery is
possibly covered by an HP warranty, instructions include a warranty ID. A message refers you to the HP
website for more information about ordering a replacement battery.

Running on external AC power

For information on connecting to AC power, refer to the Setup Instructions poster provided in the
computer box.

The computer does not use battery power when the computer is connected to AC external power with
an approved AC adapter or an optional docking/expansion device.

WARNING! To reduce potential safety issues, use only the AC adapter provided with the computer,

a replacement AC adapter provided by HP, or a compatible AC adapter purchased from HP.

Connect the computer to external AC power under any of the following conditions:

WARNING! Do not charge the computer battery while you are onboard aircraft.

When charging or calibrating a battery

●

When installing or modifying system software

●

Running on external AC power

43

When writing information to a disc (select models only)

●

When running Disk Defragmenter on computers with internal hard drives

●

When performing a backup or recovery

●

When you connect the computer to external AC power:

The battery begins to charge.

●

The display brightness increases.

●

The power meter icon on the Windows desktop changes appearance.

●

When you disconnect external AC power, the following events occur:

The computer switches to battery power.

●

The display brightness automatically decreases to save battery life.

●

The power meter icon on the Windows desktop changes appearance.

●

Troubleshooting power problems

Test the AC adapter if the computer exhibits any of the following symptoms when it is connected to AC
power:

The computer does not turn on.

●

The display does not turn on.

●

The power lights are off.

●

To test the AC adapter:

1. Shut down the computer.

2. Remove the battery from the computer.

3. Connect the AC adapter to the computer, and then plug it into an AC outlet.

4. Turn on the computer.

If the power lights turn on, the AC adapter is working properly.

●

If the power lights remain off, check the connection from the AC adapter to the computer and

●

the connection from the AC adapter to the AC outlet to make sure the connections are secure.

If the connections are secure and the power lights remain off, the AC adapter is not

●

functioning and should be replaced.

Contact customer support for information on obtaining a replacement AC power adapter.

HP CoolSense

HP CoolSense automatically detects when the computer is not in a stationary position and adjusts

performance and fan settings to keep the surface temperature of your computer at the optimum level of
comfort.

44 Chapter 6 Managing power

When HP CoolSense is off, the position of the computer is not detected and the performance and fan
options remain at the factory setting. As a result, the surface temperature of the computer may be
higher than it would be with HP CoolSense on.

To turn CoolSense off or on, follow these steps:

From the Start screen, type cool, select Settings, and then select HP CoolSense.

▲

HP CoolSense

45

Refreshing your software content with Intel Smart Connect Technology (select models only)

When the computer is in the Sleep state, Intel Smart Connect Technology periodically causes the
computer to exit Sleep. Smart Connect then updates the content for certain open applications and
reinitiates Sleep. As a result, your work is immediately available to you as soon as you exit Sleep. You
do not have to wait while updates are downloaded.

To enable this feature or manually adjust the settings, on the Start screen, type smart, and then

▲

select Intel® Smart Connect Technology.

Shutting down (turning off) the computer

CAUTION: Unsaved information is lost when the computer shuts down. Be sure to save your work

before shutting down the computer.

The Shut down command closes all open programs, including the operating system, and then turns off
the display and computer.

Shut down the computer under any of the following conditions:

When you need to replace the battery or access components inside the computer

●

When you are connecting an external hardware device that does not connect to a USB or video

●

port

When the computer will be unused and disconnected from external power for an extended period

●

Although you can turn off the computer with the power button, the recommended procedure is to use
the Windows Shut down command:

NOTE: If the computer is in the Sleep state or in Hibernation, you must first exit Sleep or Hibernation

before shutdown is possible by briefly pressing the power button.

1. Save your work and close all open programs.

2. From the Start screen, point to the upper-right or lower-right corner of the screen.

3. When the charms list opens, select Settings, select the Power icon, and then select Shut

down.

If the computer is unresponsive and you are unable to use the preceding shutdown procedures, try the
following emergency procedures in the sequence provided:

Press ctrl+alt+delete, and then select the Power icon in the lower-right corner of the screen. Then

●

select Shut down.

Press and hold the power button for at least 5 seconds.

●

Disconnect the computer from external power.

●

Remove the battery.

●

46 Chapter 6 Managing power

7 Managing and sharing information

Drives are digital storage devices that help you store, manage, share, and access information. Your
computer has an internal hard drive that stores your computer's software and operating system, as well
as provides storage for all of your personal files. Some computers also have an optional optical drive
that allows you to read or write to a CD, DVD, or Blu-ray Disc (BD), to play and record audio and
video.

For added capacity or functionality, connect an external drive (purchased separately), such as an
optical drive or hard drive, or insert a digital storage card to import information directly from your
phone or camera. A Universal Serial Bus (USB) flash drive, connected to the USB port on your
computer, also allows quick data transfer. Some devices use the computer's power to run; others have
their own power source. Some devices come with software that must be installed.

NOTE: For information about connecting external wireless devices, see Connecting to a network

on page 15.

NOTE: For more information about required software and drivers, or to learn which computer port to

use, see the manufacturer's instructions.

Using a USB device

Most computers have more than one USB port, because this versatile interface allows you to connect
numerous kinds of external devices to your computer, such as a USB keyboard, mouse, external drive,
printer, scanner, or USB hub.

Your computer has more than one type of USB port. See
the types of USB ports you have on this computer. Be sure to purchase devices that are compatible with
your computer.

Type Description

USB 2.0 Transfers data at 60 MB/s.

USB 3.0 Transfers data at 640 MB/s. USB 3.0 ports, also known as

Getting to know your computer on page 4 for

SuperSpeed ports, are also compatible with USB 1.0 and 2.0
devices.

Using a USB device

47

Connecting a USB device

CAUTION: To reduce the risk of damage to a USB connector, use minimal force to connect the

device.

Connect the USB cable for the device to the USB port.

▲

NOTE: The USB port on your computer may look slightly different from the illustration in this

section.

A sound indicates that the device has been detected.

NOTE: The first time you connect a USB device, a message displays on the Desktop and an icon

shows in the notification area letting you know that the device is recognized by the computer.

Removing a USB device

CAUTION: To reduce the risk of damage to a USB connector, do not pull on the cable to remove the

USB device.

CAUTION: To reduce the risk of loss of information or an unresponsive system, use the following

procedure to remove the USB device safely:

1. Save your information and close all programs associated with the device.

2. From the Desktop, click or tap the hardware icon in the notification area, at the far right of the

taskbar. A message, Safely Remove Hardware and Eject Media displays. Follow the on-screen
instructions.

Connecting a powered USB device

CAUTION: To reduce the risk of damage to the equipment when connecting a powered device, be

sure that the device is turned off and its AC power cord is unplugged.

1. Connect the device to the computer.

2. Plug the device power cord into a grounded AC outlet.

3. Turn on the device.

48 Chapter 7 Managing and sharing information

To disconnect an unpowered external device, stop the device, and then disconnect it from the
computer. To disconnect a powered external device, turn off the device, disconnect it from the
computer, and then unplug the AC power cord.

Using a USB device

49

Inserting and removing a digital storage card

To insert a digital storage card:

CAUTION: To reduce the risk of damage to the digital card connectors, use minimal force to insert a

digital card.

1. Hold the card label-side up, with the connectors facing the computer.

2. Insert the card into the digital storage slot, and then press in on the card until it is firmly seated.

A sound indicates that the device has been detected.

To remove a digital storage card:

CAUTION: To reduce the risk of loss of data or an unresponsive system, use the following procedure

to safely remove the digital card.

1. Save your information and close all programs associated with the digital card.

2. From the Desktop, click or tap the remove hardware icon in the notification area, at the far right of

the taskbar. Then, follow the on-screen instructions.

3. Press in on the card (1), and then remove it from the slot (2).

NOTE: If the card is not ejected, pull the card out of the slot.

50 Chapter 7 Managing and sharing information

Sharing data and drives and accessing software

When your computer is part of a network, you are not limited to using only the information that is
stored on your computer. Networked computers can exchange software and data with each other.

NOTE: When a disc like a DVD movie or game is copy-protected, it cannot be shared.

To share folders or libraries on the same network:

1. On the Desktop, open File Explorer.

2. Select the Share tab on the Libraries window, and then select Specific people.

3. Type a name in the File Sharing box, and then select Add.

4. Select Share and then follow the on-screen instructions.

To share information from your Local Disk:

1. On the Desktop, open File Explorer.

2. Select Local Disk (C:) on the Libraries window.

3. Select the Share tab, and then select Advanced sharing.

4. On the Local Disk (C:) Properties window, select Advanced Sharing.

5. Check Share this folder.

To share drives on the same network:

1.

On the Desktop, right-click the Wireless icon
touch screen, press and hold the Wireless icon.

2. Select Open Network and Sharing Center.

3. Under View your active networks, select an active network.

4. Select Change advanced sharing settings to set sharing options for privacy, network

discovery, file and printer sharing or other network options.

in the notification area. On models with a

Sharing data and drives and accessing software

51

8 Maintaining your computer

It is important to perform regular maintenance to keep your computer in optimal condition. This chapter
provides information about improving the performance of your computer by running tools such as Disk
Defragmenter and Disk Cleanup. It also provides information about updating your programs and
drivers, instructions for cleaning your computer, and tips for traveling with your computer.

Improving performance

Everyone wants a fast computer and by performing regular maintenance tasks, using tools such as Disk
Defragmenter and Disk Cleanup, you can drastically improve the performance of your computer.

Using HP 3D DriveGuard

HP 3D DriveGuard protects a hard drive by parking the drive and halting data requests under either of
the following conditions:

You drop the computer.

●

You move the computer with the display closed while the computer is running on battery power.

●

A short time after the end of one of these events, HP 3D DriveGuard returns the hard drive to normal
operation.

NOTE: Because solid-state drives (SSD) lack moving parts, HP 3D DriveGuard is unnecessary.

NOTE: Hard drives in the primary hard drive bay are protected by HP 3D DriveGuard. Hard drives

connected to USB ports are not covered by HP 3D DriveGuard.

For more information, see the HP 3D DriveGuard software Help.

Using Disk Defragmenter

As you use your computer over time, the files on the hard drive become fragmented. A fragmented
drive means data on your drive is not contiguous (sequential) and, because of this, the hard drive
works harder to locate files, thus slowing down the computer. Disk Defragmenter consolidates (or
physically reorganizes) the fragmented files and folders on the hard drive so that the system can run
more efficiently.

NOTE: It is not necessary to run Disk Defragmenter on solid-state drives.

After you start Disk Defragmenter, it works without supervision. However, depending on the size of your
hard drive and the number of fragmented files, Disk Defragmenter may take more than an hour to
complete.

HP recommends defragmenting your hard drive at least once a month. You may set Disk Defragmenter
to run on a monthly schedule, but you can defragment your computer manually at any time.

52 Chapter 8 Maintaining your computer

To run Disk Defragmenter:

1. Connect the computer to AC power.

2. From the Start screen, type disk, select Settings, and then select Defragment and optimize

your drives.

3. Follow the on-screen instructions.

For additional information, access the Disk Defragmenter software Help.

Using Disk Cleanup

Disk Cleanup searches the hard drive for unnecessary files that you can safely delete to free up disk
space and help the computer run more efficiently.

To run Disk Cleanup:

1. From the Start screen, type disk, select Settings, and then select Free up disk space by

deleting unnecessary files.

2. Follow the on-screen instructions.

Updating programs and drivers

HP recommends that you update your programs and drivers on a regular basis to the latest versions.
Updates can resolve issues and bring new features and options to your computer. Technology is always
changing, and updating programs and drivers allows your computer to run the latest technology
available. For example, older graphics components might not work well with the most recent gaming
software. Without the latest driver, you would not be getting the most out of your equipment.

Go to the HP website to download the latest versions of HP programs and drivers. For U.S. support, go

http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.com/country/

to

us/en/wwcontact_us.html. In addition, register to receive automatic update notifications when they

become available.

Cleaning your computer

Cleaning your computer and external devices helps keep them in good working condition. If you don't
clean your computer, dust and dirt particles can build up.

CAUTION: Avoid using the following cleaning products to clean your computer:

Strong solvents, such as alcohol, acetone, ammonium chloride, methylene chloride, and hydrocarbons,
which can permanently damage the surface of the computer.

Cleaning the display, sides, and cover

Gently wipe the display using a soft, lint-free cloth moistened with an alcohol-free glass cleaner. Allow
the display to dry before closing the computer cover.

Use a pre-moistened germicidal wipe to clean the sides and cover. Fibrous materials, such as paper
towels, can scratch the computer.

Updating programs and drivers

53

NOTE: When cleaning the cover of the computer, use a circular motion to aid in removing dirt and

debris.

Cleaning the TouchPad and keyboard

CAUTION: Never allow liquids to drip between the keys on the keyboard, even when you are

cleaning the computer. This can permanently damage internal components.

To clean and disinfect the TouchPad and keyboard, use a soft microfiber cloth or a static-free cloth

●

without oil (such as a chamois cloth) moistened with an alcohol-free glass cleaner or use an
acceptable germicidal disposable wipe.

To prevent keys from sticking and to remove dust, lint, and particles from the keyboard, use a can

●

of compressed air with a straw extension.

WARNING! To reduce the risk of electric shock or damage to internal components, do not use

a vacuum cleaner attachment to clean the keyboard. A vacuum cleaner can deposit household
debris on the keyboard surface.

Traveling with or shipping your computer

If you have to travel with or ship your computer, here are some tips to keep in mind to keep your
equipment safe.

Prepare the computer for traveling or shipping:

●

Back up your information to an external drive.

◦

Remove all discs and all external media cards, such as digital storage cards, from the

◦

computer.

Turn off, and then disconnect all external devices.

◦

Shut down the computer.

◦

Take along a backup of your information. Keep the backup separate from the computer.

●

When traveling by air, carry the computer as hand luggage; do not check it in with the rest of

●

your luggage.

CAUTION: Avoid exposing a drive to magnetic fields. Security devices with magnetic fields

include airport walk-through devices and security wands. Airport conveyer belts and similar
security devices that check carry-on baggage use X-rays instead of magnetism and do not damage
drives.

If you plan to use the computer during a flight, listen for the in-flight announcement that tells you

●

when you are allowed to use your computer. In-flight computer use is at the discretion of the
airline.

If you are shipping the computer or a drive, use suitable protective packaging and label the

●

package “FRAGILE.”

If the computer has a wireless device installed, the use of these devices may be restricted in some

●

environments. Such restrictions may apply onboard aircraft, in hospitals, near explosives, and in

54 Chapter 8 Maintaining your computer

hazardous locations. If you are uncertain of the policy that applies to the use of a particular
device, ask for authorization to use your computer before you turn it on.

If you are traveling internationally, follow these suggestions:

●

Check the computer-related customs regulations for each country or region on your itinerary.

◦

Check the power cord and adapter requirements for each location in which you plan to use

◦

the computer. Voltage, frequency, and plug configurations vary.

WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not

attempt to power the computer with a voltage converter kit sold for appliances.

Traveling with or shipping your computer

55

9 Securing your computer and

information

Computer security is essential for protecting the confidentiality, integrity, and availability of your
information. Standard security solutions provided by the Windows operating system, HP applications,
the non-Windows Setup Utility (BIOS), and other third-party software can help protect your computer
from a variety of risks, such as viruses, worms, and other types of malicious code.

IMPORTANT: Some security features listed in this chapter may not be available on your computer.

Computer risk Security feature

Unauthorized use of the computer Power-on password

Computer viruses Antivirus software

Unauthorized access to data Firewall software

Unauthorized access to Setup Utility (BIOS) settings and other
system identification information

Ongoing or future threats to the computer Software updates

Unauthorized access to a Windows user account User password

Unauthorized removal of the computer Security cable lock

Using passwords

A password is a group of characters that you choose to secure your computer information and to
protect online transactions. Several types of passwords can be set. For example, when you set up your
computer for the first time, you were asked to create a user password to secure your computer.
Additional passwords can be set in Windows or in the HP Setup Utility (BIOS) that is preinstalled on
your computer.

You may find it helpful to use the same password for a Setup Utility (BIOS) feature and for a Windows
security feature.

Use the following tips for creating and saving passwords:

To reduce the risk of being locked out of the computer, record each password and store it in a

●

secure place away from the computer. Do not store passwords in a file on the computer.

Administrator password

When creating passwords, follow requirements set by the program.

●

Change your passwords at least every three months.

●

56 Chapter 9 Securing your computer and information

An ideal password is long and has letters, punctuation, symbols, and numbers.

●

Before you send your computer for service, back up your files, delete confidential files, and then

●

remove all password settings.

For additional information about Windows passwords, such as screen-saver passwords, from the Start
screen, type h, and then select Help and Support.

Setting Windows passwords

Password Function

User password Protects access to a Windows user account.

Administrator password Protects administrator-level access to computer contents.

Setting Setup Utility (BIOS) passwords

Password Function

NOTE: This password cannot be used to access Setup Utility

(BIOS) contents.

Administrator password

Power-on password

Must be entered each time you access Setup Utility

●

(BIOS).

If you forget your administrator password, you cannot

●

access Setup Utility (BIOS).

NOTE: The administrator password can be used in place of

the power-on password.

NOTE: Your administrator password is not interchangeable

with an administrator password set in Windows, nor is it
displayed as it is set, entered, changed, or deleted.

NOTE: If you enter the power-on password at the first

password check, you must enter the administrator password to
access Setup Utility (BIOS).

Must be entered each time you turn on or restart the

●

computer.

If you forget your power-on password, you cannot turn

●

on or restart the computer.

NOTE: The administrator password can be used in place of

the power-on password.

NOTE: A power-on password is not displayed as it is set,

entered, changed, or deleted.

To set, change, or delete an administrator or power-on password in Setup Utility (BIOS):

1. To start Setup Utility (BIOS), turn on or restart the computer, quickly press esc, and then press f10.

2. Use the arrow keys to select Security, and then follow the on-screen instructions.

Using passwords

57

Your changes take effect when the computer restarts.

Using Internet security software

When you use your computer to access email, a network, or the Internet, you potentially expose your
computer to computer viruses, spyware, and other online threats. To help protect your computer,
Internet security software that includes antivirus and firewall features may be preinstalled on your
computer as a trial offer. To provide ongoing protection against newly discovered viruses and other
security risks, security software must be kept up to date. It is strongly recommended that you upgrade
the security software trial offer or purchase the software of your choice in order to fully protect your
computer.

Using antivirus software

Computer viruses can disable programs, utilities, or the operating system, or cause them to function
abnormally. Antivirus software can detect most viruses, destroy them, and in most cases, repair any
damage they have caused.

To provide ongoing protection against newly discovered viruses, antivirus software must be kept up to
date.

An antivirus program may be preinstalled on your computer. It is strongly recommended that you use
the antivirus program of your choice in order to fully protect your computer.

For more information about computer viruses, from the Start screen, type support, and then select the

HP Support Assistant app.

Using firewall software

Firewalls are designed to prevent unauthorized access to a system or network. A firewall can be
software you install on your computer and/or network, or it can be a combination of both hardware
and software.

There are two types of firewalls to consider:

Host-based firewalls—Software that protects only the computer it is installed on.

●

Network-based firewalls—Installed between your DSL or cable modem and your home network to

●

protect all the computers on the network.

When a firewall is installed on a system, all data sent to and from the system is monitored and
compared with a set of user-defined security criteria. Any data that does not meet those criteria is
blocked.

Installing software updates

HP, Windows, and third-party software installed on your computer should be regularly updated to
correct security problems and improve software performance. For more information, see

programs and drivers on page 53.

Updating

58 Chapter 9 Securing your computer and information

Installing Windows updates

Updates to the operating system and other software may have become available after the computer left
the factory. Microsoft sends out alerts regarding critical updates. To protect the computer from security
breaches and computer viruses, install all critical updates from Microsoft as soon as you receive an
alert.

To be sure that all available updates are installed on the computer, observe these guidelines:

Run Windows Update as soon as possible after you set up your computer. From the Start screen,

●

type update, select Settings, and then select Windows Update.

Run Windows Update monthly thereafter.

●

Obtain updates to Windows and other Microsoft programs, as they are released, from the

●

Microsoft website and through the updates link in Help and Support.

Installing HP and third-party software updates

HP recommends that you regularly update the software and drivers that were originally installed on
your computer. To download the latest versions, go to the HP website. For U.S. support, go to

http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.com/country/
us/en/wwcontact_us.html. At this location, you can also register to receive automatic update

notifications when they become available.

If you have installed third-party software after you purchased your computer, regularly update the
software. Software companies provide software updates to their products to correct security problems
and improve functionality of the software.

Securing your wireless network

When you set up your wireless network, always enable security features. For more information, see

Protecting your WLAN on page 17.

Backing up your software applications and information

Regularly back up your software applications and information to protect them from being permanently
lost or damaged through a virus attack or a software or hardware failure. For more information, see

Backing up, restoring, and recovering on page 64.

Using an optional security cable lock

A security cable lock, which is purchased separately, is designed to act as a deterrent, but it may not
prevent the computer from being mishandled or stolen. Security cable locks are only one of several
methods that should be employed as part of a complete security solution to help maximize theft
protection.

Securing your wireless network

59

The security cable slot on your computer may look slightly different from the illustration in this section.
For the location of the security cable slot on your computer, see

on page 4.

1. Loop the security cable lock around a secured object.

2. Insert the key (1) into the security cable lock (2).

3. Insert the security cable lock into the security cable slot on the computer (3), and then lock the

security cable lock with the key.

Getting to know your computer

4. Remove the key and keep it in a safe place.

60 Chapter 9 Securing your computer and information

10 Using Setup Utility (BIOS) and

System Diagnostics

Setup Utility, or Basic Input/Output System (BIOS), controls communication between all the input and
output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Setup Utility
(BIOS) includes settings for the types of devices installed, the startup sequence of the computer, and the
amount of system and extended memory.

Starting Setup Utility (BIOS)

To start Setup Utility (BIOS), turn on or restart the computer, quickly press esc, and then press f10.

Information about how to navigate in Setup Utility (BIOS) is located at the bottom of the screen.

NOTE: Use extreme care when making changes in Setup Utility (BIOS). Errors can prevent the

computer from operating properly.

Updating the BIOS

Updated versions of the BIOS may be available on the HP website.

Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs.

Some download packages contain a file named Readme.txt, which contains information regarding
installing and troubleshooting the file.

Determining the BIOS version

To determine whether available BIOS updates contain later BIOS versions than those currently installed
on the computer, you need to know the version of the system BIOS currently installed.

BIOS version information (also known as ROM date and System BIOS) can be displayed by pressing fn
+esc (if you are already in Windows) or by using Setup Utility (BIOS).

1. Start Setup Utility (BIOS). See

2. Use the arrow keys to select Main.

3. Note your current BIOS version.

4. To exit Setup Utility (BIOS) without saving your changes, use the arrow keys to select Exit, select

Exit Discarding Changes, and then press enter.

Starting Setup Utility (BIOS) on page 61.

Starting Setup Utility (BIOS)

61

Downloading a BIOS update

CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download

and install a BIOS update only when the computer is connected to reliable external power using the AC
adapter. Do not download or install a BIOS update while the computer is running on battery power,
docked in an optional docking device, or connected to an optional power source. During the
download and installation, follow these instructions:

Do not disconnect power from the computer by unplugging the power cord from the AC outlet.

Do not shut down the computer or initiate Sleep.

Do not insert, remove, connect, or disconnect any device, cable, or cord.

1. From the Start screen, type support, and select the HP Support Assistant app.

2. Select Updates and then tune-ups, and then select Check for HP updates now.

3. Follow the on-screen instructions.

4. At the download area, follow these steps:

a. Identify the most recent BIOS update and compare it to the BIOS version currently installed on

your computer. If the update is more recent than your BIOS, make a note of the date, name,
or other identifier. You may need this information to locate the update later, after it has been
downloaded to your hard drive.

b. If the update is more recent than your BIOS, follow the on-screen instructions to download

your selection to the hard drive.

Make a note of the path to the location on your hard drive where the BIOS update is
downloaded. You will need to access this path when you are ready to install the update.

NOTE: If you connect your computer to a network, consult the network administrator before

installing any software updates, especially system BIOS updates.

BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the
download is complete. If no instructions are displayed, follow these steps:

1. From the Start screen, type e, and then select File Explorer.

2. Select your hard drive designation. The hard drive designation is typically Local Disk (C:).

3. Using the hard drive path you recorded earlier, open the folder on your hard drive that contains

the update.

4. Double-click or double-tap the file that has an .exe extension (for example, filename.exe).

The BIOS installation begins.

5. Complete the installation by following the on-screen instructions.

NOTE: After a message on the screen reports a successful installation, you can delete the

downloaded file from your hard drive.

62 Chapter 10 Using Setup Utility (BIOS) and System Diagnostics

Using System Diagnostics

System Diagnostics allows you to run diagnostic tests to determine if the computer hardware is
functioning properly.

To start System Diagnostics:

1. Turn on or restart the computer, quickly press esc, and then press f2.

2. Select the diagnostic test you want to run, and then follow the on-screen instructions.

NOTE: If you need to stop a diagnostic test while it is running, press esc.

Using System Diagnostics

63

11 Backing up, restoring, and

recovering

Your computer includes tools provided by HP and the operating system to help you safeguard your
information and retrieve it if you ever need to. These tools will help you return your computer to a
proper working state or even back to the original factory state, all with simple steps.

This chapter provides information about the following processes:

Creating recovery media and backups

●

Restoring and recovering your system

●

NOTE: This guide describes an overview of backing up, restoring and recovering options. For more

details about the tools provided, see Help and Support. From the Start screen, type h, and then select

Help and Support.

Creating recovery media and backups

Recovery after a system failure is only as good as your most recent backup.

1. After you successfully set up the computer, create HP Recovery media. This step creates a backup

of the HP Recovery partition on the computer. The backup can be used to reinstall the original
operating system in cases where the hard drive is corrupted or has been replaced.

HP Recovery media you create will provide the following recovery options:

System Recovery—Reinstalls the original operating system and the programs that were

●

installed at the factory.

Minimized Image Recovery—Reinstalls the operating system and all hardware-related drivers

●

and software, but not other software applications.

Factory Reset—Restores the computer to its original factory state by deleting all information

●

from the hard drive and re-creating the partitions. Then it reinstalls the operating system and
the software that was installed at the factory.

See

Creating HP Recovery media on page 65.

2. As you add hardware and software programs, create system restore points. A system restore point

is a snapshot of certain hard drive contents saved by Windows System Restore at a specific time.
A system restore point contains information that Windows uses, such as registry settings. Windows
creates a system restore point for you automatically during a Windows update and during other
system maintenance (such as a software update, security scanning, or system diagnostics). You
can also manually create a system restore point at any time. For more information and steps for
creating specific system restore points, see Windows Help and Support. From the Start screen,
type h, and then select Help and Support.

3. As you add photos, video, music, and other personal files, create a backup of your personal

information. Windows File History can be set to regularly and automatically back up files from

64 Chapter 11 Backing up, restoring, and recovering

libraries, desktop, contacts, and favorites. If files are accidentally deleted from the hard drive and
they can no longer be restored from the Recycle Bin, or if files become corrupted, you can restore
the files that you backed up using File History. Restoring files is also useful if you ever choose to
reset the computer by reinstalling Windows or choose to recover using HP Recovery Manager.

NOTE: File History is not enabled by default, so you must turn it on.

For more information and steps for enabling Windows File History, see Windows Help and
Support. From the Start screen, type h, and then select Help and Support.

Creating HP Recovery media

HP Recovery Manager is a software program that offers a way to create recovery media after you
successfully set up the computer. HP Recovery media can be used to perform system recovery if the
hard drive becomes corrupted. System recovery reinstalls the original operating system and the
software programs installed at the factory, and then configures the settings for the programs. HP
Recovery media can also be used to customize the system or aid in the replacement of a hard drive.

Only one set of HP Recovery media can be created. Handle these recovery tools carefully, and

●

keep them in a safe place.

HP Recovery Manager examines the computer and determines the required storage capacity for

●

the blank USB flash drive or the number of blank DVD discs that will be required.

To create recovery discs, your computer must have an optical drive with DVD writer capability,

●

and you must use only high-quality blank DVD-R, DVD+R, DVD-R DL, or DVD+R DL discs. Do not
use rewritable discs such as CD±RW, DVD±RW, double-layer DVD±RW, or BD-RE (rewritable Blu­ray) discs; they are not compatible with HP Recovery Manager software. Or instead you can use a
high-quality blank USB flash drive.

If your computer does not include an integrated optical drive with DVD writer capability, but you

●

would like to create DVD recovery media, you can use an external optical drive (purchased
separately) to create recovery discs, or you can obtain recovery discs for your computer from the
HP website. For U.S. support, go to

http://welcome.hp.com/country/us/en/wwcontact_us.html. If you use an external optical

go to
drive, it must be connected directly to a USB port on the computer; the drive cannot be connected
to a USB port on an external device, such as a USB hub.

Be sure that the computer is connected to AC power before you begin creating the recovery

●

media.

The creation process can take up to an hour or more. Do not interrupt the creation process.

●

If necessary, you can exit the program before you have finished creating all of the recovery DVDs.

●

HP Recovery Manager will finish burning the current DVD. The next time you start HP Recovery
Manager, you will be prompted to continue, and the remaining discs will be burned.

To create HP Recovery media:

1. From the Start screen, type recovery, and then select HP Recovery Manager.

2. Select Recovery Media Creation, and follow the on-screen instructions to continue.

If you ever need to recover the system, see

http://www.hp.com/go/contactHP. For worldwide support,

Recovering using HP Recovery Manager on page 68.

Creating recovery media and backups

65

Restore and recovery

There are several options for recovering your system. Choose the method that best matches your
situation and level of expertise:

If you need to restore your personal files and data, you can use Windows File History to restore

●

your information from the backups you created. For more information and steps for using File
History, see Windows Help and Support. From the Start screen, type h, and then select Help and
Support.

If you need to correct a problem with a preinstalled application or driver, use the Drivers and

●

Applications Reinstall option of HP Recovery Manager to reinstall the individual application or
driver.

From the Start screen, type recovery, select HP Recovery Manager, and then select Drivers
and Applications Reinstall, and follow the on-screen instructions.

If you want to restore the system to a previous state without losing any personal information,

●

Windows System Restore is an option. System Restore allows you to restore without the
requirements of Windows Refresh or a reinstallation. Windows creates system restore points
automatically during a Windows update and other system maintenance events. Even if you did not
manually create a restore point, you can choose to restore to a previous point, automatically
created. For more information and steps for using Windows System Restore, see Windows Help
and Support. From the Start screen, type h, and then select Help and Support.

If you want a quick and easy way to recover the system without losing your personal information,

●

settings, or apps that came preinstalled on your computer or were purchased from the Windows
Store, consider using Windows Refresh. This option does not require backing up data to another
drive. See

If you want to reset your computer to its original state, Windows provides an easy way to remove

●

all personal data, apps, and settings, and reinstall Windows.

For more information, see

If you want to reset your computer using a minimized image, you can choose the HP Minimized

●

Image Recovery option from the HP Recovery partition (select models only) or HP Recovery media.
Minimized Image Recovery installs only drivers and hardware-enabling applications. Other
applications included in the image continue to be available for installation through the Drivers and
Applications Reinstall option in HP Recovery Manager.

For more information, see Recovering using HP Recovery Manager on page 68.

If you want to recover the computer's original factory partitioning and content, you can choose the

●

System Recovery option from the HP Recovery media. For more information, see

HP Recovery Manager on page 68.

If you have replaced the hard drive, you can use the Factory Reset option of HP Recovery media to

●

restore the factory image to the replacement drive. For more information, see

Recovery Manager on page 68.

Using Windows Refresh for quick and easy recovery on page 67.

Remove everything and reinstall Windows on page 67.

Recovering using

Recovering using HP

If you wish to remove the recovery partition to reclaim hard drive space, HP Recovery Manager

●

offers the Remove Recovery Partition option.

For more information, see

66 Chapter 11 Backing up, restoring, and recovering

Removing the HP Recovery partition on page 70.

Using Windows Refresh for quick and easy recovery

When your computer is not working properly and you need to regain system stability, the Windows
Refresh option allows you to start fresh and keep what is important to you.

IMPORTANT: Refresh removes any traditional applications that were not originally installed on the

system at the factory.

NOTE: During Refresh, a list of removed traditional applications will be saved so that you have a

quick way to see what you might need to reinstall. See Help and Support for instructions on reinstalling
traditional applications. From the Start screen, type h, and then select Help and Support.

NOTE: You may be prompted for your permission or password when using Refresh. See Windows

Help and Support for more information. From the Start screen, type h, and then select Help and
Support.

To start Refresh:

1. On the Start screen, point to the far-right upper or lower corner of the screen to display the

charms.

2. Select Settings.

3. Select Change PC settings in the bottom-right corner of the screen, and then select General

from the PC settings screen.

4. Scroll the right-side choices down to display Refresh your PC without affecting your files.

5. Under Refresh your PC without affecting your files, select Get started, and follow the

on-screen instructions.

Remove everything and reinstall Windows

Sometimes you want to perform detailed reformatting of your computer, or you want to remove
personal information before you give away or recycle your computer. The process described in this
section provides a speedy, simple way to return the computer to its original state. This option removes
all personal data, apps, and settings from your computer, and reinstalls Windows.

IMPORTANT: This option does not provide backups of your information. Before using this option,

back up any personal information you wish to retain.

You can initiate this option by using the f11 key or from the Start screen.

To use the f11 key:

1. Press f11 while the computer boots.

– or –

Press and hold f11 as you press the power button.

2. Choose your keyboard layout.

3. Select Troubleshoot from the boot options menu.

4. Select Reset your PC, and follow the on-screen instructions.

Restore and recovery

67

To use the Start screen:

1. On the Start screen, point to the far-right upper or lower corner of the screen to display the

charms.

2. Select Settings.

3. Select Change PC settings in the bottom-right corner of the screen, and then select General

from the PC settings screen.

4. Scroll the right-side choices down to display Remove everything and reinstall Windows.

5. Under Remove everything and reinstall Windows, select Get started, and follow the

on-screen instructions.

Recovering using HP Recovery Manager

HP Recovery Manager software allows you to recover the computer to its original factory state. Using
the HP Recovery media you created, you can choose from one of the following recovery options:

System Recovery—Reinstalls the original operating system, and then configures the settings for the

●

programs that were installed at the factory.

Minimized Image Recovery—Reinstalls the operating system and all hardware-related drivers and

●

software, but not other software applications.

Factory Reset—Restores the computer to its original factory state by deleting all information from

●

the hard drive and re-creating the partitions. Then it reinstalls the operating system and the
software that was installed at the factory.

The HP Recovery partition (select models only) allows Minimized Image Recovery.

What you need to know

HP Recovery Manager recovers only software that was installed at the factory. For software not

●

provided with this computer, you must either download the software from the manufacturer's
website or reinstall the software from the media provided by the manufacturer.

Recovery through HP Recovery Manager should be used as a final attempt to correct computer

●

issues.

HP Recovery media must be used if the computer hard drive fails.

●

To use the Factory Reset or System Recovery options, you must use HP Recovery media.

●

If the HP Recovery media do not work, you can obtain recovery media for your system from the HP

●

website. For U.S. support, go to

http://welcome.hp.com/country/us/en/wwcontact_us.html.

to

IMPORTANT: HP Recovery Manager does not automatically provide backups of your personal data.

Before beginning recovery, back up any personal data you wish to retain.

http://www.hp.com/go/contactHP. For worldwide support, go

68 Chapter 11 Backing up, restoring, and recovering

Using the HP Recovery partition to recover a minimized image (select models only)

The HP Recovery partition (select models only) allows you to perform a minimized image recovery
without the need for recovery discs or a recovery USB flash drive. This type of recovery can only be
used if the hard drive is still working.

To start HP Recovery Manager from the HP Recovery partition:

1. Press f11 while the computer boots.

– or –

Press and hold f11 as you press the power button.

2. Choose your keyboard layout.

3. Select Troubleshoot from the boot options menu.

4. Select Recovery Manager, and follow the on-screen instructions.

Using HP Recovery media to recover

You can use HP Recovery media to recover the original system. This method can be used if your system
does not have an HP Recovery partition or if the hard drive is not working properly.

1. If possible, back up all personal files.

2. Insert the first HP Recovery disc you created into an optional external optical drive, and then

restart the computer.

– or –

Insert the HP Recovery USB flash drive you created into a USB port on your computer, and then
restart the computer.

NOTE: If the computer does not automatically restart in HP Recovery Manager, change the

computer boot order. See

3. Follow the on-screen instructions.

Changing the computer boot order on page 69.

Changing the computer boot order

If computer does not restart in HP Recovery Manager, you can change the computer boot order, which
is the order of devices listed in BIOS where the computer looks for startup information. You can change
the selection for an optical drive or a USB flash drive.

To change the boot order:

1. Insert the HP Recovery media you created.

2. Restart the computer, quickly press esc, and then press f9 for boot options.

3. Select the optical drive or USB flash drive you want to boot from.

4. Follow the on-screen instructions.

Restore and recovery

69

Removing the HP Recovery partition

HP Recovery Manager software allows you to remove the HP Recovery partition to free up hard drive
space.

IMPORTANT: Removing the HP Recovery partition means you can no longer use Windows Refresh,

the Windows Remove everything and reinstall Windows option, or the HP Recovery Manager option
for minimized image recovery. Create HP Recovery media before removing the Recovery partition to
ensure you have recovery options; see

Follow these steps to remove the HP Recovery partition:

1. From the Start screen, type recovery, and then select HP Recovery Manager.

2. Select Remove Recovery Partition, and follow the on-screen instructions to continue.

Creating HP Recovery media on page 65.

70 Chapter 11 Backing up, restoring, and recovering

12 Specifications

Input power

The power information in this section may be helpful if you plan to travel internationally with the
computer.

The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC
power source must be rated at 100–240 V, 50–60 Hz. Although the computer can be powered from a
standalone DC power source, it should be powered only with an AC adapter or a DC power source
supplied and approved by HP for use with this computer.

The computer can operate on DC power within the following specifications. Operating voltage and
current varies by platform.

Input power Rating

Operating voltage and current 19.5 V dc @ 3.33 A – 65 W

DC plug of external HP power supply

NOTE: This product is designed for IT power systems in Norway with phase-to-phase voltage not

exceeding 240 V rms.

NOTE: The computer operating voltage and current can be found on the system regulatory label.

Operating environment

Factor Metric U.S.

Temperature

Operating 5°C to 35°C 41°F to 95°F

Nonoperating -20°C to 60°C -4°F to 140°F

Relative humidity (noncondensing)

Operating 10% to 90% 10% to 90%

Nonoperating 5% to 95% 5% to 95%

Maximum altitude (unpressurized)

Input power

71

Operating -15 m to 3,048 m -50 ft to 10,000 ft

Nonoperating -15 m to 12,192 m -50 ft to 40,000 ft

72 Chapter 12 Specifications

13 Electrostatic Discharge

Electrostatic discharge is the release of static electricity when two objects come into contact—for
example, the shock you receive when you walk across the carpet and touch a metal door knob.

A discharge of static electricity from fingers or other electrostatic conductors may damage electronic
components. To prevent damage to the computer, damage to a drive, or loss of information, observe
these precautions:

If removal or installation instructions direct you to unplug the computer, unplug it after being

●

properly grounded and before removing a cover.

Keep components in their electrostatic-safe containers until you are ready to install them.

●

Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.

●

Use nonmagnetic tools.

●

Before handling components, discharge static electricity by touching an unpainted metal surface of

●

the component.

If you remove a component, place it in an electrostatic-safe container.

●

If you need more information about static electricity or assistance with component removal or
installation, contact support.

73

Index

A

AC adapter 6
AC adapter, testing 44
action keys

decrease screen brightness 36
functions 35
Help and Support 36
identifying 12
increase screen brightness 36
next track or section 36
play, pause, resume 36
previous track or section 36
switch screen image 36
using 35
volume down 36
volume mute 36
volume up 36

wireless 36
antivirus software, using 58
audio 21
audio functions, checking 22
audio-in (microphone) jack 7
audio-out (headphone) jack 7, 21

B

back up

personal files 65
backing up software and

information 59
backups 64
battery

conserving power 42
disposing 43
replacing 43

storing 43
battery bay 13, 14
battery information, finding 41
battery lock, identifying 13
battery power 40
battery release latch 13
battery temperature 43
best practices 1
BIOS

determining version 61

downloading an update 62

updating 61
Bluetooth device 15, 18
boot order

changing HP Recovery

Manager 69

buttons

left TouchPad 9

power 11

right TouchPad 9

TouchPad on/off 9

C

cables

USB 48
caps lock light, identifying 10
caring for your computer 53
checking audio functions 22
cleaning your computer 53
components

bottom 13

display 7

left side 6

right side 4

top 9
computer reset 67
computer, traveling 43
configuring audio for HDMI 24
connecting to a WLAN 18
connector, power 6
conservation, power 42
corporate WLAN connection 18
critical battery level 42
CyberLink PowerDVD 25

D

deleted files

restoring 66
digital card

inserting 50
Digital Media Slot, identifying 5
Disk Cleanup software 53
Disk Defragmenter software 52

E

edge swipe gestures 29, 33

right-edge swipe 29
top-edge swipe 29

edge—swipe gestures

top-edge swipe 34
electrostatic discharge 73
esc key, identifying 12
external AC power, using 43
external devices 48

F

f1 key 36
f10 key 36
f11 key 36
f12 key 36
f2 key 36
f3 key 36
f4 key 36
f6 key 36
f7 key 36
f8 key 36
f9 key 36
firewall software 58
fn key, identifying 12, 37
fun things to do 1

H

hard drive

HP 3D DriveGuard 52
hard drive light 5
HDMI

configuring audio 24
HDMI port, connecting 24
HDMI port, identifying 5, 20
headphones

connecting 22
headset microphone

connecting 22
Help and Support

how to access 36
Hibernation

exiting 39

74 Index

initiated during critical battery

level 42

initiating 38, 39

high-definition devices,

connecting 24, 25

hot keys

description 37
display system information 37
functions 37

using 37
HP 3D DriveGuard 52
HP and third-party software

updates, installing 59

HP Recovery Manager 68

correcting boot problems 69

starting 69
HP Recovery media

creating 65

recovery 69
HP Recovery partition 69

recovery 69

removing 70
hubs 47

I

input power 71
installing

critical updates 59

optional security cable lock 59
Integrated numeric keypad 37
integrated numeric keypad,

identifying 12, 37

integrated webcam light,

identifying 7, 20
Intel Rapid Start Technology 38
Intel Wireless Display 25
internal microphone, identifying

8, 20
Internet connection setup 17
Internet security software, using

58

J

jack

audio-in (microphone) 7
audio-out (headphone) 7, 21
network 5
RJ-45 (network) 5
RJ-45 (network) lights 5

K

keyboard

using 35
keyboard hot keys, identifying 37
keypad, integrated numeric 12
keys

action 12

esc 12

fn 12

num lock 12

Windows applications 12

Windows logo 12

L

labels

regulatory 14

service 13

wireless certification 14

WLAN 14
LAN

connecting 19
latch, battery release 13
left-edge swipe 30, 34
lights

AC adapter 6

caps lock 10

hard drive 5

mute 10

power 5, 10

TouchPad 9, 10

webcam 7, 20

wireless 10

M

maintenance

Disk Cleanup 53

Disk Defragmenter 52
minimized image

creating 68
minimized image recovery 69
model description

label 13
mouse

using 35
mouse, external

setting preferences 26
music 21
mute light, identifying 10

N

network cable

LAN requirements 19
network jack, identifying 5
num lock key, identifying 12, 37

O

operating environment 71
optional external devices, using

48

original system recovery 68

P

passwords

Setup Utility (BIOS) 57

Windows 57
pinch touch screen gesture 32
pinching TouchPad gesture 28
ports

HDMI 5, 20, 24

Intel Wireless Display 25

USB 2.0 7, 21

USB 3.0 5, 21
power

battery 40

conserving 42
power button, identifying 11
power connector, identifying 6
power lights, identifying 5, 10
power meter 40
power settings 40
PowerDVD 25
product name and number,

computer 13

public WLAN connection 18

R

recovery 66, 67

discs 65, 69

HP Recovery Manager 68

media 69

starting 69

supported discs 65

system 68

USB flash drive 69

using HP Recovery media 65
recovery media

creating 65

creating using HP Recovery

Manager 65

Index

75

recovery partition 69

removing 70

recycle

computer 66, 67

refresh 67

computer 66

regulatory information

regulatory label 14
wireless certification labels 14

remove everything and reinstall

Windows 67

reset

computer 66, 67
steps 67

restore

Windows File History 66
right-edge swipe 33
RJ-45 (network) jack, identifying 5

S

scrolling TouchPad gesture 28
security cable lock, installing 59
security cable slot, identifying 6
security, wireless 17
serial number 13
service label, computer 13
service labels

locating 13
setting password protection on

wakeup 39
setup of WLAN 17
Setup Utility (BIOS) passwords 57
shipping the computer 54
Shortcut keys

Windows 8 shortcut keys 36
shutdown 46
Sleep

exiting 39

initiating 38, 39
slots

Digital Media 5

security cable 6
software

CyberLink PowerDVD 25

Disk Cleanup 53

Disk Defragmenter 52
software updates, installing 58
speakers

connecting 21
speakers, identifying 11, 21

storing a battery 43
stretch touch screen gesture 32
supported discs

recovery 65
system information hot key 37
system recovery 68
system restore point

creating 64

restoring 66

T

tapping touch gesture 27
temperature 43
testing an AC adapter 44
touch gestures 26

tapping 27
Touch screen

touch screen, using 30
Touch screen gestures 33, 34

edge–swipe gestures 33, 34

one-finger slide 31

pinch 32

tapping 31
TouchPad 26

buttons 9
TouchPad gestures 26, 29

edge—swipe gestures 30

pinching 28

scrolling 28

zooming 28
TouchPad light 9
TouchPad on/off button 9
TouchPad reader light 10
TouchPad zone, identifying 9
traveling with the computer 14,

43, 54

turning off the computer 46

U

unresponsive system 46
USB 2.0 ports, identifying 7, 21
USB 3.0 ports, identifying 5, 21
USB cable, connecting 48
USB devices

connecting 48

description 47

removing 48
USB hubs 47
using external AC power 43
using passwords 56

V

vents, identifying 6, 13
video 22

W

warranty period

label 13
webcam 21
webcam light, identifying 7, 20
webcam, identifying 7, 20
Windows

backup 65

File History 65, 66

Refresh 66, 67

reinstall 66, 67

remove everything and reinstall

option 67
reset 67
restoring files 66
system restore point 64, 66

Windows applications key,

identifying 12

Windows logo key, identifying

12
Windows passwords 57
Windows updates, installing 59
Wireless Assistant software 15
wireless button 15
wireless certification label 14
wireless controls

button 15
operating system 15

Wireless Assistant software 15
wireless light 10, 15
wireless network (WLAN)

connecting 18

corporate WLAN connection

18
equipment needed 17
functional range 18
public WLAN connection 18
security 17
using 16

wireless network, securing 59
WLAN antennas, identifying 7
WLAN device 16
WLAN label 14

Z

zooming TouchPad gesture 28

76 Index