HP Surestore 330fx, Surestore 660ex, C1104, C1105 User Manual
Capacity Upgrade
For C1104/05 Series Jukeboxes
Important! Read This First
This upgrade requires code to be downloaded to the controller PCA and the drives.
BEFORE starting this upgrade, obtain the following:
* The downloadable code required for this upgrade. FTP this code
from hpgrsg.gr.hp.com (15.38.89.10
Further download instructions are available at that address.
* A PC with a SCSI interface and appropriate cables.
* A utility to download the code - DOWNLD2 or HP TOOLSET (Version 1.95ce
or later) from CoComp
) using an "anonymous" login.
HP Part No. C1159-90001
Printed in USA June, 1996
Edition 1 0596
Hewlett-Packard Company, 1996
Capacity Upgrade For C1104/05 Jukeboxes
Before upgrade:
(# of drives and slots)
C1104F/G/H
(4 drives, 128 slots)
C1105F/G/H
(6 drives, 128 slots)
Table 1: C1104/05 Series Capacity Upgrade Options
a. After you install this capacity upgrade (C1159F/G/H), you are able to install 1
or more 2-drive upgrades ( C1158F/G/H).
Upgraded to the equivalent of a:
C1107F/G/H (238 slots)
a
ESD Precautions
The optical disk jukebox contains very sensitive electrical components. It is EXTREMELY IMPORTANT that you follow the proper procedures for preventing ESD (Electrostatic Discharge). Use wristgrounding straps, anti-static mats, and anti-static work stations when removing and replacing the
major assemblies.
Caution
Failure to follow proper procedures could lead to intermittent
failures and/or premature hard failures in the disk controller
and mechanism.
Tools Required
The following tools are needed for assembly/disassembly of the autochanger:
• Torx driver with the following bits: T-10, T-15, T-20
• 1/4-inch hex nut driver
3
Kit Contents
• 24 - magazine guides, 8 slot (makes 12 sets) — # C1100-44x00
• 6 - magazine guides, 6 slot (makes 3 sets) — # C1160-41x15
• 1 - interposer PCA — # C1107-60x05
• 1 - controller PCA — # C1107-60x01
• 1 - power Supply (200W)— # C1107-60x32
• 1 - short AC power cable (to 12V) — # C1107-60x50
• 1 - SCSI cable (lower) — # C1107-60x60
• 1 - interposer (lower) power cable —- # C1107-60x68
• 1 - enclosure for SCSI repeater/converter PCA — # C1107-60x81
• 1 - SCSI repeater/converter/LUN PCA — # C1107-60x08
• 1 - SCSI terminator, single-ended — # 1250-2548
• 1 - SCSI terminator, wide differential — # A1658-62024
• 3 - drive brackets — # C1107-60x47
• 12 - screws (RLG) — # 0515-2282
• 6 - hex standoff screws — # 0380-4416
• 1 - ferrite cable clip — # 9170-1648
• 2 - product upgrade label sheets (Upgrade to: ) — # 5181-9902
• 1 - 600FX name plate — # C1107-84x09 (C1159F and C1159G kits only)
• 1 - these instructions
Note
The “x” in the part numbers listed in the following parts tables
represents a number from “0” to “9” depending on the
revision of the part. For example, if the part is newly
released, the number will be “0”. The first time the part is
revised, the number increments to “1”; the second time the
part is revised, the number increments to“2”, and so on.
If you are unsure of the current part number, enter a “0” or a
“1” in place of the “x” when checking your parts database and
the current part number will be displayed.
4
Before You Begin
Caution
Do NOT switch off power to the jukebox until you are sure the
SCSI bus is inactive
SCSI bus is active can cause data loss and/or indeterminate
bus states.
When doing this upgrade, be sure that disk cartridges are not
moved from their original slot locations.
the cartridges, record their SLOT LOCATIONS and
ORIENTATION so they can be replaced to their ORIGINAL
positions. Failure to follow this practice results in a serious
loss of file system integrity.
1. Look in the jukebox front "window" and make sure that there are no disks in any drive.
Use the control panel to eject any disk still in a drive.
. Switching off the jukebox when the
If you need to remove
2. Bring the jukebox “down.”
Procedures for bringing this jukebox offline depend on the specific host system. Coordinate with
the system administrator to prepare this jukebox for the upgrade. This may involve “downing” the
host system also.
3. Remove power from the jukebox.
4. Disconnect the SCSI interface from the host.
5
Installing a Capacity Upgrade
Caution
When doing this conversion, be sure that disk cartridges are
not moved from their original slot locations.
remove the cartridges, record their SLOT LOCATIONS and
ORIENTATION so they can be replaced to their ORIGINAL
positions. Failure to follow this practice results in a serious
loss of file system integrity.
1. Remove the 3 right-side panels and the 3 back panels.
To remove the 3 right-side panels, you must start at the bottom panel. The bottom panel may have
2 slotted/T-15 T orx screws at each corner (long arrows in Figure 1) if the customer has re-installed
them after installation. The 2 screws at the bottom of each of the other side panels are T-20.
The rear panels may be removed in any order. Each panel is held by 4 T-20 screws.
If you need to
Figure 1: Screws on side and rear panels
2. Remove the 2 RFI panels (see Figure 2).
There are 6 T-20 screws around the edge of each panel.
6
Loading...