HP B321 User Manual

B321/B421

HP LED Digital Signage Display User Guide

B321/B421

Safety Instructions

Warnings and Precautions

KNOW THESE SAFETY SYMBOLS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

CAUTION: FCC/CSA regulations state that any unauthorized

changes or modications to this equipment may

void the user’s authority to operate it.

CAUTION: To prevent electric shock, match the wide blade

of plug to the wide slot, and fully insert the plug.

TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

The Socket-outlet should be installed near the apparatus and be easily accessible.

Read and follow these instructions when connecting and using your Public Information Display:

• Unplug the display if you are not going to use it for an extensive period of time.

• Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is off. However, never use alcohol, solvents

or ammonia-based liquids.

• Consult a service technician if the display does not operate

normally when you have followed the instructions in this manual.

• The casing cover should be opened only by qualied service

personnel.

• Keep the display out of direct sunlight and away from stoves or any other heat sources.

• Remove any object that could fall into the vents or prevent proper cooling of the display’s electronics.

• Do not block the ventilation holes on the cabinet.

• Keep the display dry. To avoid electric shock, do not expose

it to rain or excessive moisture.

• If turning off the display by detaching the power cable, wait for 6 seconds before re-attaching the power cable for normal operation.

• To avoid the risk of shock or permanent damage to the set do not expose the display to rain or excessive moisture.

• When positioning the display, make sure the power plug and outlet are easily accessible.

• IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast remains on the screen for an extended period of time, it may leave an ‘after-image’ or ‘ghost image’ on the front of the screen. This is a well-known phenomenon that is caused by the shortcomings inherent in LCD technology. In most cases the afterimage will disappear gradually over a period of time after the power has been switched off. Be aware that the after-image symptom cannot be repaired and is not covered under warranty.

B321/B421

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. If the provided plug does not t

into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket,

or table specied by the manufacturer, or

sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing

is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING: To prevent injury, this apparatus must be securely

attached to the oor/wall in accordance with the

installation instructions.

CAUTION: These servicing instructions are for use by

qualied service personnel only. To reduce the

risk of electric shock,do not perform any servicing other than that contained in the operating

instructions unless you are qualitied to do so.

CAUTION: Excessive sound pressure from earphones and

headphones can cause hearing loss. Adjustment

of the equalizer to maximum increases the

earphone and headphone output voltage and the sound pressure level. Therefore, to protect your

hearing, adjust the equalizer to an appropriate

level.

For UL/CUL application: For use only with UL Listed Wall Mount Bracket with minimum weight/load:

Model Viewable Image Size Minimum weight/load (kg)

B321 80.0cm(31.5 in.)diagonal 19.8

B421 106.7cm(42 in.)diagonal 35.7

For CB application: The equipment and its associated

mounting means still remain secure during the test.

Model

B321 6.6 200 × 100 M6 × (16 + X) B421 11.9 400 × 400 M6 × (20 + X)

Unit Weight

(kg)

VESA Size

(mm)

Mounting Screws*

(X=Thickness of wall-

mount plate)

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

WARNING: Apparatus shall not be exposed to dripping or

splashing and no objects lled with liquids, such

as vases, shall be placed on the apparatus.

WARNING: The batteries (batteries installed) shall not be

exposed to excessive heat such as sunshine, re

or the like.

WARNING: The mains plug or appliance coupler is used as

the disconnect device,the disconnect device shall remain readily operable.

WARNING: To prevent the spread of re, keep candles or

other open ames away from this product at all

times.

iii

B321/B421

Federal Communications Commission (FCC) Notice (U.S. Only)

This equipment has been tested and found

to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions manual, may cause harmful interference to radio communications. Operation

of this equipment in a residential area is likely

to cause harmful interference in which case the

user will be required to correct the interference

at his own expense.

Changes or modications not expressly

approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.

To prevent damage which may result in re or shock hazard, do

not expose this appliance to rain or excessive moisture.

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCECAUSING EQUIPMENT REGULATIONS.

Electric, Magnetic and Electronmagnetic Fields (“EMF”)

1. We manufacture and sell many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive electromagnetic signals.

2. One of our leading Business Principles is to take all necessary health and safety measures for our products, to

comply with all applicable legal requirements and to stay

well within the EMF standards applicable at the time of producing the products.

3. We are committed to develop, produce and market products that cause no adverse health effects.

4. We conrm that if its products are handled properly for their

intended use, they are safe to use according to scientic

evidence available today.

5. We play an active role in the development of international EMF and safety standards, enabling us to anticipate further developments in standardization for early integration in its products.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

B321/B421

Information for U.K. only

WARNING – THIS APPLIANCE MUST BE EARTHED.

Important:

(B)

(A)

This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.

3. Ret the fuse cover.

If the tted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug tted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A.

NOTE

: The severed plug must be destroyed to avoid a

possible shock hazard should it be inserted into a 13A socket elsewhere.

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead – not simply over the three wires.

How to connect a plug

The wires in the mains lead are coloured in accordance with the following code:

BLUE – “NEUTRAL” (“N”)

BROWN – “LIVE” (“L”)

GREEN & YELLOW – “EARTH” (“E”)

1. The GREEN & YELLOW wire must be connected to the terminal in the plug which is marked with the letter “E” or by the Earth symbol or coloured GREEN or GREEN & YELLOW.

2. The BLUE wire must be connected to the terminal which is marked with the letter “N” or coloured BLACK.

3. The BROWN wire must be connected to the terminal which marked with the letter “L” or coloured RED.

B321/B421

≤200

China RoHS

中国电子信息产品污染控制标识要求

仅适用于非热带气候条件下安全使用 :

本产品有毒有害物质或元素的名称及含量标识表：

有毒有害物质或元素

零部件名称

塑料外框 O O O O O O 后壳 O O O O O O

CCFL X X O O O O

LCD

面板

LED X O O O O O

电源基板 X O O O O O 主基板 X O O O O O 按键基板 X O O O O O 底座 O O O O O O 电源线 X O O O O O 其他线材 X O O O O O 遥控器 X O O O O O *：电路板组件包括印刷电路板及其构成的零部件，如电阻、电容、

集成电路、连接器等。 ○：表示该有害物质在该部件所有均质材料中的含量均在SJ/

T11363-2006《电子信息产品中有毒有害物质的限量要求》规定的限量要求以下。

×：表示该有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006《电子信息产品中有毒有害物质的限量要求》规定的限量要求；

备注：以上“×”的部件，部分含有有害物质超过是由于目前行业技术水平所限，暂时无法实现替代或减量化。

铅

(Pb)汞 (Hg)镉 (Cd)

六价铬

(Cr 6+)

多溴联苯

(PBBs)

多溴二苯醚

(PBDEs)

汉文仅适用于非热带气候条件下安全使用。

蒙古文

藏文

维文

壮文

Dan hab yungh youq gij dienheiq diuzgen mbouj dwg diegndat haenx ancienz sawjyungh.

仅适用于海拔 2000m 以下地区安全使用 :

汉文仅适用于海拔 2000m 以下地区安全使用。

蒙古文

藏文

维文

壮文 Hai dou gaxgonq, wngdang sien duenh denvasen bae.

“注意

汉文

蒙古文

如果电池更换不当会有爆炸危险只能用同样类型或等效类型的电池来更换”

环保使用期限

在产品本体上标示的该标志表示环境保护使用期限为

电子信息产品的环境保护使用期限是指电子信息产品中所含的有毒有害物质或元素不会向外部泄漏或出现突然变异，并且电子信息产品的用户在使用该电子信息产品时也不会对环境造成严重污染或对人体、财产带来严重损害的期限。

在环境保护期限中，请按照使用说明书使用本产品。

本环境保护使用不覆盖易损件：电池。

《废弃电子产品回收处理管理条例》提示性说明

为了更好地关爱及保护地球，当用户不再需要此产品或产品寿命终止时，请遵守国家废弃电器电子产品回收处理相关法律规定，将其交给当地具有国家认可的回收处理资质的厂商进行回收处理。

年。

藏文

维文

壮文

汉文

蒙古文

藏文

维文

壮文

“Louzsim Danghnaeuz denyouz vuenh ndaej mbouj habdangq aiq miz gij yungyiemj fatseng bauqcaq Cijndaej yungh gij denyouz doengzyiengh loihhingz roxnaeuz daengjyauq loihl haenx vuenh”

“接入本设备的有线网络天线必须与保护接地隔离 , 不然可能会引起着火等危险 !”

“Gij mizsienq vangjloz denhsen ciephaeuj bonj sezbi daeuj haenx itdingh aeu caeuq gij ciepdieg baujhoh doxliz, mboujne aiq miz gij yungyiemj dawzfeiz daengj!”

End-of-Life Disposal

Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of.

Please nd out about the local regulations on how to dispose of

your old display from your local dealer.

(For customers in Canada and U.S.A.)

This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on recycling contact www.eia.org (Consumer Education Initiative)

Waste Electrical and Electronie EquipmentWEEE

Attention users in European Union private households

This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EC governing used electrical and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of

this equipment through a designated waste electrical and electronic equipment collection.

To determine the locations for dropping off such waste electrical and electronic, contact your

local government ofce, the waste disposal

organization that serves your household or the store at which you purchased the product.

B321/B421

End of Life Directives-Recycling

Your new Public Information Display contains several materials that can be recycled for new users.

Please dispose of according to all Local, State, and Federal laws.

As an ENERGY STAR Partner, we have determined that this product meets the

ENERGY STAR guidelines for energy efciency.

vii

B321/B421

Table Of Contents

1. Unpacking and Installation ..................... 1

1.1. Unpacking ......................................... 1

1.2. Package Contents ............................. 1

1.3. Installation Notes ...............................1

1.4. Mounting on a Wall ............................ 1

2. Parts and Functions ................................ 3

2.1. Control Panel ....................................3

2.2. Input/Output Terminals ...................... 4

2.3. Remote Control ................................. 5

2.3.1. General functions .................... 5

2.3.2. Inserting batteries in the remote

control ..................................... 6

2.3.3. Handling the remote control .... 6

2.3.4. Operating range of the remote

control ..................................... 6

3. Connection ............................................... 7

3.1. Connecting External Equipments ...... 7

5.1.2. Sound menu .......................... 14

5.1.3. General settings menu .......... 14

5.2. Network Settings ............................. 15

6. Input mode ............................................. 16

7. Cleaning and Troubleshooting ............. 17

7.1. Cleaning .......................................... 17

7.2. Troubleshooting ...............................18

8. TechnicalSpecications ....................... 19

8.1. B321 ................................................ 19

8.2. B421 ................................................ 20

3.2. Connecting Multiple Displays ............ 8

3.2.1. RS232C control connection

(optional) ................................. 8

3.2.2. IR connection (optional) .......... 8

3.3. IR Pass-through Connection

(optional) ........................................... 8

3.4. Wire-connecting to Network

4. Operation ................................................ 10

4.1. Watch the Connected Video Source 10

4.2. Change Picture Format ................... 10

4.3. Play Multimedia Files ......................10

4.3.1. Play les from computer ....... 10

4.3.2. Play multimedia les from USB

device .................................... 10

4.4. Play options ..................................... 11

4.4.1. Playing music les ................ 11

4.4.2. Playing movie les ................ 12

(optional) 9

4.4.3. Playing photo les ................. 12

5. Change your settings ............................ 13

5.1. Settings ........................................... 13

5.1.1. Picture menu ......................... 13

viii

1. Unpacking and Installation

HDMI Cable

1.1. Unpacking

• This product is packed in a carton, together with the standard accessories.

• Any other optional accessories will be packed separately.

• Due to the size and weight of this display it is recommended for two people to move it.

• After opening the carton, ensure that the contents are complete and in good condition.

1.2. Package Contents

Please verify that you received the following items with your package content:

• LCD display

• Documention & Software Disc

• Remote control with AAA batteries

• Power cord (1.8 m)

• VGA cable (1.8 m)

• HDMI cable (1.8 m)

B321/B421

Remote Control

and AAA Batteries

* Only one power cord is provided with your display.

Disc

Power Cord For China

VGA Cable

For North America For UK

NOTE:

• Keep the package box and packing material for shipping the display.

1.3. Installation Notes

• Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please

consult your service agent.

• The distance between the back of the product and the wall should be maintained for proper ventilation. Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as not to shorten the service life of the electronic components.

• The product can normally operate only under 2000 m in altitude. In installations at altitudes above 2000 m, some abnormalities may be experienced.

• Note:Display models provided in this guide are available in select countries/regions.Go to www.hp.com/support for additional information.

1.4. Mounting on a Wall

To mount this display to a wall, you will have to obtain a standard wall-mounting kit. We recommend using a mounting interface that complies with UL1678 standard in North America.

+ 20 hidden pages