HP AT496AV-2, QY467AW, AT496AV-1 User Manual

Hardware Reference Guide

HP Compaq 6005 Pro Small Form Factor Business PC

Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.

The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

This document contains proprietary information that is protected by copyright. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company.

Hardware Reference Guide

HP Compaq 6005 Pro Small Form Factor Business PC

First Edition (September 2009)

Document Part Number: 576439-001

About This Book

This guide provides basic information for upgrading this computer model.

WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily

harm or loss of life.

CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage

to equipment or loss of information.

NOTE: Text set off in this manner provides important supplemental information.

ENWW iii

iv About This Book ENWW

Table of contents

1 Product Features

Standard Configuration Features ......................................................................................................... 1

Front Panel Components ..................................................................................................................... 2

Media Card Reader Components ......................................................................................................... 3

Rear Panel Components ...................................................................................................................... 4

Keyboard .............................................................................................................................................. 5

Using the Windows Logo Key .............................................................................................. 6

Serial Number Location ........................................................................................................................ 7

2 Hardware Upgrades

Serviceability Features ......................................................................................................................... 8

Warnings and Cautions ........................................................................................................................ 8

Removing the Computer Access Panel ................................................................................................ 9

Replacing the Computer Access Panel .............................................................................................. 10

Removing the Front Bezel .................................................................................................................. 11

Removing Bezel Blanks ..................................................................................................................... 12

Replacing the Front Bezel .................................................................................................................. 13

Using the Small Form Factor Computer in a Tower Orientation ........................................................ 14

Installing Additional Memory .............................................................................................................. 15

DIMMs ............................................................................................................................... 15

DDR3-SDRAM DIMMs ...................................................................................................... 15

Populating DIMM Sockets ................................................................................................. 16

Installing DIMMs ................................................................................................................ 17

Removing or Installing an Expansion Card ........................................................................................ 20

Drive Positions ................................................................................................................................... 26

Installing and Removing Drives .......................................................................................................... 27

System Board Drive Connections ...................................................................................... 29

Removing an External 5.25-inch Drive .............................................................................. 30

Installing an Optical Drive into the 5.25-inch Drive Bay ..................................................... 32

Removing an External 3.5-inch Drive ................................................................................ 35

Installing a Drive into the 3.5-inch External Drive Bay ....................................................... 37

Removing and Replacing the Primary 3.5-inch Internal SATA Hard Drive ........................ 39

Removing and Replacing a Removable 3.5-inch SATA Hard Drive .................................. 43

ENWW v

Appendix A Specifications

Appendix B Battery Replacement

Appendix C External Security Devices

Installing a Security Lock .................................................................................................................... 52

Cable Lock ......................................................................................................................... 52

Padlock .............................................................................................................................. 53

HP Business PC Security Lock .......................................................................................... 53

Front Bezel Security .......................................................................................................... 55

Appendix D Electrostatic Discharge

Preventing Electrostatic Damage ....................................................................................................... 57

Grounding Methods ............................................................................................................................ 57

Appendix E Computer Operating Guidelines, Routine Care and Shipping Preparation

Computer Operating Guidelines and Routine Care ............................................................................ 58

Optical Drive Precautions ................................................................................................................... 59

Operation ........................................................................................................................... 59

Cleaning ............................................................................................................................. 59

Safety ................................................................................................................................. 59

Shipping Preparation .......................................................................................................................... 59

Index ................................................................................................................................................................... 60

vi ENWW

1 Product Features

Standard Configuration Features

The HP Compaq Small Form Factor features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). Instructions for using the utility are provided in the Troubleshooting Guide.

NOTE: The Small Form Factor computer can also be used in a tower orientation. For more information,

Using the Small Form Factor Computer in a Tower Orientation on page 14 in this guide.

see

Figure 1-1 Small Form Factor Configuration

ENWW Standard Configuration Features 1

Front Panel Components

Drive configuration may vary by model.

Figure 1-2 Front Panel Components

Table 1-1 Front Panel Components

1 5.25-inch Optical Drive

2 Optical Drive Activity Light 7 Microphone/Headphone Connector

3 Optical Drive Eject Button 8 3.5-inch Media Card Reader (optional)

6 USB (Universal Serial Bus) Ports

4 Dual-State Power Button 9 Hard Drive Activity Light

5 Power On Light 10 Headphone Connector

NOTE: When a device is plugged into the Microphone/Headphone Connector, a dialog box will pop up asking if you

want to use the connector for a microphone line Line-In device or a headphone. You can reconfigure the connector at any time by double-clicking the Realtek HD Audio Manager icon in the Windows taskbar.

NOTE: The Power On Light is normally green when the power is on. If it is flashing red, there is a problem with the

computer and it is displaying a diagnostic code. Refer to the Troubleshooting Guide to interpret the code.

Some models are configured with a 5.25-inch bezel blank covering this bay.

Some models are configured with a 3.5-inch bezel blank covering this bay.

2 Chapter 1 Product Features ENWW

Media Card Reader Components

The media card reader is an optional device available on some models only. Refer to the following illustration and table to identify the media card reader components.

Figure 1-3 Media Card Reader Components

Table 1-2 Media Card Reader Components

No. Slot Media

1 xD

2 MicroSD

3 Media Card Reader

Activity Light

4 SD/MMC+/miniSD

5 USB

6 CompactFlash I/II

7 MS PRO/MS PRO DUO

xD-Picture Card (xD)

●

MicroSD (T-Flash)

●

Secure Digital (SD)

●

Secure Digital High

●

Capacity (SDHC)

MiniSD

●

USB (Universal Serial

●

Bus) Port

CompactFlash Card

●

Type 1

Memory Stick (MS)

●

MagicGate Memory

●

Stick (MG)

MagicGate Memory

●

Duo

MicroSDHC

●

MiniSDHC

●

MultiMediaCard

●

(MMC)

Reduced Size

●

MultiMediaCard (RS MMC)

CompactFlash Card

●

Type 2

Memory Stick Select

●

Memory Stick Duo

●

(MS Duo)

Memory Stick PRO

●

(MS PRO)

MultiMediaCard 4.0

●

(MMC Plus)

Reduced Size

●

MultiMediaCard 4.0 (MMC Mobile)

MMC Micro (adapter

●

required)

MicroDrive

●

Memory Stick PRO

●

Duo (MS PRO Duo)

Memory Stick PRO-

●

HG Duo

Memory Stick Micro

●

(M2) (adapter required)

8 1394

1394 Port (available

●

on select models only)

ENWW Media Card Reader Components 3

Rear Panel Components

Figure 1-4 Rear Panel Components

Table 1-3 Rear Panel Components

1 RJ-45 Network Connector 6 DisplayPort Monitor Connector

2 Serial Connector 7 VGA Monitor Connector

3 PS/2 Mouse Connector (green) 8 PS/2 Keyboard Connector (purple)

4 Power Cord Connector 9 Line-Out Connector for powered audio

5 Universal Serial Bus (USB) 10 Line-In Audio Connector (blue)

NOTE: Arrangement and number of connectors may vary by model.

An optional second serial port and an optional parallel port are available from HP.

When a device is plugged into the blue Line-In Audio Connector, a dialog box will pop up asking if you want to use the connector for a line-in device or a microphone. You can reconfigure the connector at any time by double-clicking the Realtek HD Audio Manager icon in the Windows taskbar.

The monitor connectors on the system board are inactive when a graphics card is installed in the computer.

If a graphics card is installed into the PCI, PCI Express x1, or the PCI Express x16 slot, the connectors on the graphics card and the system board may be used at the same time. The connectors on the system board may be used at the same time only if an ATI graphics card is installed in the PCI Express x16 connector. Some settings may need to be changed in Computer Setup to use both connectors. For information about setting the boot VGA controller, refer to the Computer Setup (F10) Utility Guide.

devices (green)

4 Chapter 1 Product Features ENWW

Keyboard

Figure 1-5 Keyboard Components

Table 1-4 Keyboard Components

1 Function Keys Perform special functions depending on the software application being used.

2 Editing Keys Includes the following: Insert, Home, Page Up, Delete, End, and Page Down.

3 Status Lights Indicate the status of the computer and keyboard settings (Num Lock, Caps Lock,

4 Numeric Keys Work like a calculator keypad.

5 Arrow Keys Used to navigate through a document or Web site. These keys allow you to move

6 Ctrl Keys Used in combination with another key; their effect depends on the application

7 Application Key

8 Windows Logo Keys

9 Alt Keys Used in combination with another key; their effect depends on the application

Keys available in select geographic regions.

and Scroll Lock).

left, right, up, and down, using the keyboard instead of the mouse.

software you are using.

Used (like the right mouse button) to open pop-up menus in a Microsoft Office application. May perform other functions in other software applications.

Used to open the Start menu in Microsoft Windows. Used in combination with other keys to perform other functions.

software you are using.

ENWW Keyboard 5

Using the Windows Logo Key

Use the Windows Logo key in combination with other keys to perform certain functions available in the Windows operating system. Refer to

Table 1-5 Windows Logo Key Functions

The following Windows Logo Key functions are available in Microsoft Windows XP and Microsoft Windows Vista.

Keyboard on page 5 to identify the Windows Logo key.

Windows Logo Key

Windows Logo Key + d Displays the Desktop

Windows Logo Key + m Minimizes all open applications

Shift + Windows Logo Key + m Undoes Minimize All

Windows Logo Key + e Launches My Computer

Windows Logo Key + f Launches Find Document

Windows Logo Key + Ctrl + f Launches Find Computer

Windows Logo Key + F1 Launches Windows Help

Windows Logo Key + l Locks the computer if you are connected to a network domain, or

Windows Logo Key + r Launches the Run dialog box

Windows Logo Key + u Launches the Utility Manager

Windows Logo Key + Tab Windows XP - Cycles through the Taskbar buttons

In addition to the Windows Logo Key functions described above, the following functions are also available in Microsoft Windows Vista.

Displays or hides the Start menu

allows you to switch users if you are not connected to a network domain

Windows Vista - Cycles through programs on the Taskbar using the Windows Flip 3-D

Ctrl + Windows Logo Key + Tab

Windows Logo Key + Spacebar Brings all gadgets to the front and select Windows Sidebar

Windows Logo Key + g Cycles through Sidebar gadgets

Windows Logo Key + u Launches Ease of Access Center

Windows Logo Key + any number key Launches the Quick Launch shortcut that is in the position that

Use the arrow keys to cycle through programs on the Taskbar by using Windows Flip 3-D

corresponds to the number (for example, Windows Logo Key + 1 launches the first shortcut in the Quick Launch menu)

6 Chapter 1 Product Features ENWW

Serial Number Location

Each computer has a unique serial number and product ID number in the location shown below. Keep these numbers available for use when contacting customer service for assistance.

Figure 1-6 Serial Number and Product ID Location

ENWW Serial Number Location 7

2 Hardware Upgrades

Serviceability Features

The computer includes features that make it easy to upgrade and service. No tools are needed for most of the installation procedures described in this chapter.

Warnings and Cautions

Before performing upgrades be sure to carefully read all of the applicable instructions, cautions, and warnings in this guide.

WARNING! To reduce the risk of personal injury from electrical shock, hot surfaces, or fire:

Disconnect the power cord from the wall outlet and allow the internal system components to cool before touching.

Do not plug telecommunications or telephone connectors into the network interface controller (NIC) receptacles.

Do not disable the power cord grounding plug. The grounding plug is an important safety feature.

Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.

To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation, setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at

WARNING! Energized and moving parts inside.

Disconnect power to the equipment before removing the enclosure.

Replace and secure the enclosure before re-energizing the equipment.

CAUTION: Static electricity can damage the electrical components of the computer or optional

equipment. Before beginning these procedures, ensure that you are discharged of static electricity by briefly touching a grounded metal object. See Appendix D, more information.

When the computer is plugged into an AC power source, voltage is always applied to the system board. You must disconnect the power cord from the power source before opening the computer to prevent damage to internal components.

Electrostatic Discharge on page 57 for

http://www.hp.com/ergo.

8 Chapter 2 Hardware Upgrades ENWW

Removing the Computer Access Panel

1. Remove/disengage any security devices that prohibit opening the computer.

2. Remove all removable media, such as compact discs or USB flash drives, from the computer.

3. Turn off the computer properly through the operating system, then turn off any external devices.

4. Disconnect the power cord from the power outlet and disconnect any external devices.

CAUTION: Regardless of the power-on state, voltage is always present on the system board as

long as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer.

5. If the computer is on a stand, remove the computer from the stand.

6. Lift up on the access panel handle (1) then lift the access panel off the computer (2).

Figure 2-1 Removing the Access Panel

ENWW Removing the Computer Access Panel 9

Replacing the Computer Access Panel

Slide the lip on the front end of the access panel under the lip on the front of the chassis (1) then press the back end of the access panel onto the unit so that it locks into place (2).

Figure 2-2 Replacing the Access Panel

10 Chapter 2 Hardware Upgrades ENWW

Removing the Front Bezel

1. Remove/disengage any security devices that prohibit opening the computer.

2. Remove all removable media, such as compact discs or USB flash drives, from the computer.

3. Turn off the computer properly through the operating system, then turn off any external devices.

4. Disconnect the power cord from the power outlet and disconnect any external devices.

CAUTION: Regardless of the power-on state, voltage is always present on the system board as

long as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer.

5. Remove the access panel.

6. Lift up the three tabs on the side of the bezel (1), then rotate the bezel off the chassis (2).

Figure 2-3 Removing the Front Bezel

ENWW Removing the Front Bezel 11

Removing Bezel Blanks

On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch external drive bays that need to be removed before installing a drive. To remove a bezel blank:

1. Remove the access panel and front bezel.

2. To remove a bezel blank, push the two retaining tabs that hold the bezel blank in place towards

the outer right edge of the bezel (1) and slide the bezel blank back and to the right to remove it (2).

Figure 2-4 Removing a Bezel Blank

12 Chapter 2 Hardware Upgrades ENWW

Replacing the Front Bezel

Insert the three hooks on the bottom side of the bezel into the rectangular holes on the chassis (1) then rotate the top side of the bezel onto the chassis (2) and snap it into place.

Figure 2-5 Replacing the Front Bezel

ENWW Replacing the Front Bezel 13

Using the Small Form Factor Computer in a Tower Orientation

The Small Form Factor computer can be used in a tower orientation with an optional tower stand that can be purchased from HP.

1. Remove/disengage any security devices that prohibit opening the computer.

2. Remove all removable media, such as compact discs or USB flash drives, from the computer.

3. Turn off the computer properly through the operating system, then turn off any external devices.

4. Disconnect the power cord from the power outlet and disconnect any external devices.

CAUTION: Regardless of the power-on state, voltage is always present on the system board as

long as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer.

5. Orient the computer so that its right side is facing down and place the computer in the optional

stand.

Figure 2-6 Changing from Desktop to Tower Orientation

NOTE: To stabilize the computer in a tower orientation, HP recommends the use of the optional

tower stand.

6. Reconnect the power cord and any external devices, then turn on the computer.

NOTE: Ensure at least 10.2 centimeters (4 inches) of space on all sides of the computer remains clear

and free of obstructions.

14 Chapter 2 Hardware Upgrades ENWW

Installing Additional Memory

The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3SDRAM) dual inline memory modules (DIMMs).

DIMMs

The memory sockets on the system board can be populated with up to four industry-standard DIMMs. These memory sockets are populated with at least one preinstalled DIMM. To achieve the maximum memory support, you can populate the system board with up to 16-GB of memory.

DDR3-SDRAM DIMMs

For proper system operation, the DDR3-SDRAM DIMMs must be:

industry-standard 240-pin

●

unbuffered non-ECC PC3-8500 DDR3-1066 MHz-compliant or PC3-10600 DDR3-1333 MHz-

●

compliant

NOTE: 1333 MHz DIMMS may only run at a speed of 1066 MHz, depending on the processor.

1.5 volt DDR3-SDRAM DIMMs

●

The DDR3-SDRAM DIMMs must also:

support CAS latency 8 DDR3 1066 MHz (8-8-8 timing) and CAS latency 9 DDR3 1333 MHz (9-9-9

●

timing)

contain the mandatory JEDEC SPD information

●

In addition, the computer supports:

512-Mbit, 1-Gbit, and 2-Gbit non-ECC memory technologies

●

single-sided and double-sided DIMMs

●

DIMMs constructed with x8 and x16 DDR devices; DIMMs constructed with x4 SDRAM are not

●

supported

NOTE: The system will not operate properly if you install unsupported DIMMs.

ENWW Installing Additional Memory 15

+ 46 hidden pages