Page 1
Aruba 2930F 24G/48G Switch Quick
Setup Guide and Safety/Regulatory
Information
Abstract
Use this guide to assist in the basic set-up of the following Aruba 2930F 24G and 48G switch models:
JL255A Aruba 2930F 24G PoE+ 4SFP+ Switch
nl
JL253A Aruba 2930F 24G 4SFP+ Switch
nl
JL256A Aruba 2930F 48G PoE+ 4SFP+ Switch
nl
JL254A Aruba 2930F 48G 4SFP+ Switch
nl
JL261A Aruba 2930F 24G PoE+ 4SFP Switch
nl
JL259A Aruba 2930F 24G 4SFP Switch
nl
JL262A Aruba 2930F 48G PoE+ 4SFP Switch
nl
JL260A Aruba 2930F 48G 4SFP Switch
nl
JL263A Aruba 2930F 24G PoE+ 4SFP+ TAA Switch
nl
JL264A Aruba 2930F 48G PoE+ 4SFP+ TAA Switch
*5200-1182*
Part Number: 5200-1182
Published: April 2016
Edition: 1
Page 2
© Copyright 2016 Hewlett Packard Enterprise Development LP
The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services
are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting
an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or copying. Consistent with FAR
12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed
to the U.S. Government under vendor's standard commercial license.
Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard Enterprise has no control over and is not
responsible for information outside the Hewlett Packard Enterprise website.
Applicable products
JL253AAruba 2930F 24G 4SFP+ Switch
JL254AAruba 2930F 48G 4SFP+ Switch
JL259AAruba 2930F 24G 4SFP Switch
JL260AAruba 2930F 48G 4SFP Switch
JL255AAruba 2930F 24G PoE+ 4SFP+ Switch
JL256AAruba 2930F 48G PoE+ 4SFP+ Switch
JL261AAruba 2930F 24G PoE+ 4SFP Switch
JL262AAruba 2930F 48G PoE+ 4SFP Switch
JL263AAruba 2930F 24G PoE+ 4SFP+ TAA Switch
JL264AAruba 2930F 48G PoE+ 4SFP+ TAA Switch
Page 3
Aruba 2930F 24G/48G Switch Quick Setup Guide and
Safety/Regulatory Information
NOTE: The switch drawings in this document are for illustration only and may not match your
particular switch model.
NOTE: For switch and accessories installation information, browse to the manuals for your
switch model at www.hpe.com/networking/ResourceCenter.
Installation precautions
WARNING!
• The rack or cabinet should be adequately secured to prevent it from becoming unstable
and/or falling over.
• Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest
devices at the bottom and progressively lighter devices installed above.
CAUTION:
• Do not ship any switch in a rack without checking for restrictions in the Aruba 2930F Switches
Installation and Getting Started Guide. Otherwise, you may void the switch warranty.
• Ensure the power source circuits are properly grounded, then use the power cord supplied
with the switch to connect it to the power source.
• Use only approved power cords with your Aruba Networking Product. Please see the power
cord information in the section titled “Power cords” (page 10) of this guide for acceptable
power cords that are appropriate for this product. Failure to use approved power cords can
result in personal injury and product damage, and may void your product warranty.
• If your installation requires a different power cord than the one supplied with the switch, be
sure the cord is adequately sized for the switch’s current requirements. In addition, be sure
to use a power cord displaying the mark of the safety agency that defines the regulations
for power cords in your country. The mark is your assurance that the power cord can be
used safely with the switch and power supply.
• When installing the switch, the AC outlet should be near the switch and should be easily
accessible in case the switch must be powered off.
• Do not install the switch in an environment where the operating ambient temperature exceeds
its specification. See the section titled “Aruba 2930F Switch Safety and Regulatory
Information” (page 11).
• Ensure the switch does not overload the power circuits, wiring, and over-current protection.
To determine the possibility of overloading the supply circuits, add together the ampere
ratings of all devices installed on the same circuit as the switch and compare the total with
the rating limit for the circuit. The maximum ampere ratings are usually printed on the devices,
near the AC power connectors.
• Ensure the air flow around the switch is not restricted. Leave at least 3 inches (7.6 cm) for
cooling on the sides and rear of the switch. For other available air flow information, see the
Aruba 2930F Switches Installation and Getting Started Guide, located on the Hewlett Packard
Enterprise Information Library at www.hpe.com/networking/ResourceCenter.
Installation precautions 3
Page 4
Prepare for installation
1. Unpack and check included parts:
• Switch
• Console cable
• Accessory kit (installation hardware)
• Power cord
• Documentation kit
2. Prepare for installation.
CAUTION: To avoid personal injury or product damage, review the “Installation precautions”
(page 3) before beginning the installation.
3. Power on and verify that self-test completes normally. An Aruba 2930F 24G or 48G switch
does not contain a power on/off switch. It is turned on by connecting the AC power cord to
the switch and to an AC power source.
12345
6
Port LEDs: Off after self-test unless a network cable is connected and
the port is receiving link beat.
1
Global Status LED: Green after self-test in default configuration.2
Locator/Unit-Identification LED: Off after self-test.3
Speed Mode Selected LED: Off after self-test in default configuration.4
4 Aruba 2930F 24G/48G Switch Quick Setup Guide and Safety/Regulatory Information
Page 5
PoE Mode Selected LED (Only on Aruba 2930F models that support
PoE+ operation): Off after self-test in default configuration.
5
User Mode Selected: Off after self-test in default configuration.6
4. Remove the power cord from the switch and the power source.
Mounting Aruba 2930F 24-Port and 48-Port switches
Supported mounting options for the Aruba 2930F 24-Port and 48-Port switches include:
• Rack mount
• Tabletop or desktop mount
IMPORTANT: Wall-mounting or under-table mounting Aruba 2930F 24G and 48G switches
is not supported.
Two-post rack mounting option:
NOTE: For the four-post rack-mount option, see the Aruba 2930F Switches Installation and
Getting Started Guide at www.hpe.com/networking/ResourceCenter.
1. Use a #1 Phillips (cross-head) screwdriver to attach the accessory kit brackets to the switch
using the eight 8–mm M4 screws.
1
1
2
2
2. Use the four number 12–24 screws to secure the brackets to the rack.
Mounting Aruba 2930F 24-Port and 48-Port switches 5
Page 6
3. Go to “Connecting the switch to the network” (page 7).
Tabletop or desktop mounting option
1. Attach the four self-adhesive pads (included in the accessory kit) to the bottom corners of
the switch, and place the switch on a secure horizontal surface.
2. Go to “Connecting the switch to the network” (page 7).
6 Aruba 2930F 24G/48G Switch Quick Setup Guide and Safety/Regulatory Information
Page 7
Connecting the switch to the network
1. (Optional) Connect an RJ-45 console cable (included) and/or a micro-USB console cable
(not included) to a VT-100 terminal or a PC (running suitable terminal emulation software).
NOTE: If both cables are connected, input is accepted only from the Micro USB connector.
For more information, see the information on connecting a management console in the
Aruba 2930F Switches Installation and Getting Started Guide.
2. (Optional) Insert transceivers.
Connecting the switch to the network 7
Page 8
NOTE: To ensure proper operation of your switch, use only genuine HPE Aruba SFP/SFP+
transceivers supported by your switch. For more information on using transceivers, see
“SFP/SFP+ installation notes” (page 9).
3. Connect network cables.
8 Aruba 2930F 24G/48G Switch Quick Setup Guide and Safety/Regulatory Information
Page 9
NOTE: In the factory default configuration, the switch automatically obtains its IP network
settings from a DHCP or BootP server after connecting to the network. If you do not use direct
console access to initially determine the switch IP address, you can determine the assigned IP
address by inspecting your DHCP/BootP server or by querying LLDP information from another,
directly connected neighbor switch. CLI LLDP commands for an ArubaOS neighbor switch are
listed below.
For the specified port on the neighbor switch, lists the IP
address and other data for the directly connected Aruba 2930F
show lldp info remote port_#
switch (where port_# is the port used on the neighbor switch
to access the Aruba 2930F switch you are setting up).
Lists IP address and other data on all active ports on the
neighbor switch.
show lldp info remote all
SFP/SFP+ installation notes
NOTE: To ensure proper operation of your switch, use only the genuine HPE Aruba SFP/SFP+
transceivers supported by your switch. When selecting a fiber SFP device, make sure it can
function at a temperature that is not less than the recommended maximum operational temperature
of the product. Use only approved Laser Class 1 SFP transceivers.
Use only genuine HPE Aruba SFP/SFP+ transceivers
Non-HPE Aruba SFP/SFP+ transceivers are not supported. Use of genuine HPE Aruba products
ensures that your network maintains optimal performance and reliability. Should you require
additional transceivers, please contact an HPE Aruba sales representative or an authorized
reseller. For transceiver support information for your switch model, see the following two support
matrixes in the Hewlett Packard Enterprise Information Library at www.hpe.com/networking/
ResourceCenter:
• HPE Networking Legacy ProCurve Product Family Mini-GBIC and SFP Support Matrix
• HPE Networking Legacy ProCurve Product Family 10–GBE Transceiver Support Matrix
SFP/SFP+ installation notes 9
Page 10
Hot Swapping SFP/SFP+ transceivers
Supported SFP/SFP+ transceivers that you can install in your HPE Aruba switch can be “hot
swapped” – removed and installed while the switch is receiving power. However, you should
disconnect the network cables from the SFP/SFP+ transceivers before hot-swapping them.
When you replace an SFP/SFP+ transceiver with another of a different type, the switch may
retain selected port-specific configuration settings that were configured for the replaced unit. Be
sure to validate or reconfigure port settings as required.
SFP/SFP+ connections to devices with fixed speed/duplex configurations
When connecting a device to your switch port that contains an SFP/SFP+ transceiver, the speed
and duplex settings of the switch port and the connected device must match. Otherwise, you
may not get a link. For some older network devices, including some older Hewlett Packard
Enterprise devices, the default speed/duplex settings may be predefined (for example, to 1000
Mbps/Full Duplex), or otherwise set differently from the default configuration of your switch port.
Because of these default speed/duplex considerations, you should make sure that devices
connected to your SFP/SFP+ ports are properly configured. At a minimum, make sure the
configurations match.
Switch Operating System Software
For the latest software version supported by your switch, visit http://www.hpe.com/networking/
support.
For software installation and management, the Basic Operation Guide and other software
documentation for your switch at www.hpe.com/networking/ResourceCenter.
Regulatory information
For important safety, environmental, and regulatory information, see Safety and Compliance
Information for Server, Storage, Power, Networking, and Rack Products, available at http://
www.hpe.com/support/Safety-Compliance-EnterpriseProducts.
Power cords
Use one of the following power cords for an Aruba 2930F switch:
8121–1004Israel8121–0729Argentina
8121–1143Japan8121-0837Australia/New Zealand
8121–0738Switzerland8121-1071Brazil
8121–0737South Africa8121–0735Chile
8121-0964Taiwan8121–0943China
8121-0734Philippines/Thailand8121–0731Continental Europe/South
Korea
8121–0739UK/Hong Kong/Singapore/Malaysia8121–0733Denmark
8121-1141US/Canada/Mexico8121–0564India
10 Aruba 2930F 24G/48G Switch Quick Setup Guide and Safety/Regulatory Information
Page 11
Aruba 2930F Switch Safety and Regulatory Information
Aruba 2930F SwitchesCategory
32°F to 113°F (0°C to 45°C) up to 5000 FtEnvironmental
• Operating Temperature:
32°F to 104°F (0°C to 40°C) up to 10000 Ft
15% to 95% at 104°F (40°C) non-condensing
• Operating Relative Humidity:
–40°F to 158°F (–40°C to 70°C) up to 15000 ft
• Non-Operating/Storage Temperature:
15% to 95% at 149°F (65°C), non-condensing
• Non-Operating/Storage Relative Humidity:
3.0 km (10,000 ft)
• Maximum Operating Altitude:
4.6 km (15,000 ft)
• Maximum Non-Operating Altitude:
Side-to-SideAirflow direction
EN 60950-1:2006 +A11:2009 +A1:2010
+A12:2011+A2:2013
Safety-EU
IEC60950-1:2005 Ed.2; Am 1:2009+A2:2013Safety- World Wide
UL60950-1, CSA 22.2 No 60950-1North American
EN60850-1:2007 / IEC 60825-1: 2007 Class1Lasers
Class 1 Laser Products / Laser Klasse 1
EN 55022:2010, Class A
nl
EMC:
EN 55024:2010
nl
EN 6100–3–2:2006+A1:2009+A2:2009, Class A
nl
EN 61000–3–3:2008
nl
FCC CFR 47 Part 15:2010, Class A
EN 50581:2012RoHS:
AC power
nl
frequency
nl
range
PoE+ available
nl
power
Maximum AC
nl
current
Rated AC
nl
voltage
2930F 24/48–port switches Electrical
50/60 HzN/A0.6A
nl
100–127V
nl
Aruba 2930F 24G 4SFP+ Switch
(JL253A)
0.4A200–240V
50/60 HzN/A0.9A
nl
100–127V
nl
Aruba 2930F 48G 4SFP+ Switch
(JL254A)
0.6A200–240V
50/60 Hz370W4.9A
nl
100–127V
nl
Aruba 2930F 24G PoE+ 4SFP+ Switch
(JL255A)
2.4A200–240V
50/60 Hz370W5.1A
nl
100–127V
nl
Aruba 2930F 48G PoE+ 4SFP+ Switch
(JL256A)
2.5A200–240V
50/60 HzN/A0.6A
nl
100–127V
nl
Aruba 2930F 24G 4SFP Switch (JL259A)
0.4A
nl
200–240V
50/60 HzN/A0.9A
nl
100–127V
nl
Aruba 2930F 48G 4SFP Switch (JL260A)
0.6A
nl
200–240V
50/60 Hz370W4.9A
nl
100–127V
nl
Aruba 2930F 24G PoE+ 4SFP Switch
(JL261A)
2.4A
nl
200–240V
Aruba 2930F Switch Safety and Regulatory Information 11
Page 12
AC power
nl
frequency
nl
range
PoE+ available
nl
power
Maximum AC
nl
current
Rated AC
nl
voltage
2930F 24/48–port switches Electrical
50/60 Hz370W5.1A
nl
100–127V
nl
Aruba 2930F 48G PoE+ 4SFP Switch
(JL262A)
2.5A
nl
200–240V
50/60 Hz370W4.9A
nl
100–127V
nl
Aruba 2930F 24G PoE+ 4SFP+
TAA-compliant Switch (JL263A)
2.4A200–240V
50/60 Hz370W5.1A
nl
100–127V
nl
Aruba 2930F 48G PoE+ 4SFP+
TAA-compliant Switch (JL264A)
2.5A200–240V
AcousticsSwitch Model
Sound Power (LWAd) 5.0 BelAruba 2930F 24G 4SFP+ Switch (JL253A)
Sound Pressure (LpAm) (Bystander) 37.1 dB
Sound Power (LWAd) 5.4 BelAruba 2930F 48G 4SFP+ Switch (JL254A)
Sound Pressure (LpAm) (Bystander) 40.2 dB
Sound Power (LWAd) 5.4 BelAruba 2930F 24G PoE+ 4SFP+ Switch (JL255A)
Sound Pressure (LpAm) (Bystander) 40.6 dB
Sound Power (LWAd) 5.6 BelAruba 2930F 48G PoE+ 4SFP+ Switch (JL256A)
Sound Pressure (LpAm) (Bystander) 41.7 dB
Sound Power (LWAd) 5.0 BelAruba 2930F 24G 4SFP Switch (JL259A)
Sound Pressure (LpAm) (Bystander) 37.1 dB
Sound Power (LWAd) 5.4 BelAruba 2930F 48G 4SFP Switch (JL260A)
Sound Pressure (LpAm) (Bystander) 40.2 dB
Sound Power (LWAd) 5.4 BelAruba 2930F 24G PoE+ 4SFP Switch (JL261A)
Sound Pressure (LpAm) (Bystander) 40.6 dB
Sound Power (LWAd) 5.6 BelAruba 2930F 48G PoE+ 4SFP Switch (JL262A)
Sound Pressure (LpAm) (Bystander) 41.7 dB
Sound Power (LWAd) 5.4 BelAruba 2930F 24G PoE+ 4SFP+ TAA-compliant
Switch (JL263A)
Sound Pressure (LpAm) (Bystander) 40.6 dB
Sound Power (LWAd) 5.6 BelAruba 2930F 48G PoE+ 4SFP+ TAA-compliant
Switch (JL264A)
Sound Pressure (LpAm) (Bystander) 41.7 dB
CAUTION: Disconnect all power supply cords before servicing.
Table 1 Japan power cord warning
Japan Power Cord Warning
12 Aruba 2930F 24G/48G Switch Quick Setup Guide and Safety/Regulatory Information
Page 13
Table 2 China Altitude Warning
China Altitude Warning
Interior Wiring
Warning
Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia
elétrica que possua aterramento (três pinos), conforme a Norma NBR ABNT 5410, visando
a segurança dos usuários contra choques elétricos.)
Brazil Statement
Japan VCCI Class A
Korea EMC Class A Statement
Russia/Belarus/Kazakhstan/CEE Safety:
Documentation feedback
Hewlett Packard Enterprise is committed to providing documentation that meets your needs. To
help us improve the documentation, send any errors, suggestions, or comments to Documentation
Feedback (docsfeedback@hpe.com). When submitting your feedback, include the document
title, part number, edition, and publication date located on the front cover of the document. For
online help content, include the product name, product version, help edition, and publication date
located on the legal notices page.
Japan VCCI Class A 13
Loading...