Page 1
OPERATING AND SERVICE MANUAL
HP 85029B
7mm Verification Kit
HP Part Number 85029-90010
Printed July 1988
HEWLETT
PACKARD
Page 2
HP 850298
7mm VERIFICATION
KIT
SERIAL NUMBERS
This manual applies directly to any HP 850298 7mm verification
kit with the following serial prefix number:
Serial Prefix: 2818A
HP 850298 verification kits with a higher serial prefix number
are different that those documented in this manual. When this
occurs, a manual change supplement is supplied which
documents the differences.
0
Copyright
HEWLElT-PACKARD
COMPANY
1988
1400 FOUNTAINGROVE PARKWAY, SANTA ROSA, CA 95403 U.S.A.
MANUAL PART NO. 85029-90010
Microfiche Part Number 85029-90011
Printed: July 1988
ci!!a
HEWLETT
PACKARD
Page 3
WARRANTY
This Hewlett-Packard instrument product is warranted against defects in material and workmanship for a period of one year from
date of delivery. During the warranty period, Hewlett-Packard Company will, at its option, either repair or replace products which
prove to be defective.
For warranty service or repair, this product must be returned to a service facility designated by HP. Buyer shall prepay shipping
charges to HP and HP shall pay shipping charges to return the product to Buyer. However, Buyer shall pay all shipping charges,
duties, and taxes for products returned to HP from another country.
HP warrants that its software and firmware designated by HP for use with an instrument will execute its programming instructions
when properly installed on that instrument. HP does not warrant that the operation of the instrument, or software,
Or firmware
Will
be uninterrupted or error free.
LIMITATION OF WARRANTY
The foregoing warranty shall not apply to defects resulting from improper handling by Buyer, Buyer-supplied software or
interfacing, unauthorized modification or misuse, or operation outside of the environmental specifications for the product.
NO OTHER WARRANTY IS EXPRESSED OR IMPLIED, HP SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OR
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
EXCLUSIVE REMEDIES
THE REMEDIES PROVIDED HEREIN ARE BUYER’S SOLE AND EXCLUSIVE REMEDIES, HP SHALL
NOT
BE
LIABLE FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT, TORT,
OR ANY OTHER LEGAL THEORY.
ASSISTANCE
Product maintenance agreements and other customer assistance agreements are available for Hewlett-Packard Products.
For any assistance, contact your nearest Hewlett-Packard Sales and Service
O1R’ce.
Addresses are provided at the back of this
manual.
Page 4
HP 850298 7mm Verification
Kit
TABLE OF CONTENTS
1
Product
Description
.................................................
IntendedUses
..................................................
1
Applicable Systems
.............................................
2
RecommendedPractices
...........................................
2
Recommended Disc Drive and Printers
................................
2
General Information
...............................................
3
Weight
........................................................
3
Recommended Recertification Period
...............................
3
What this Kit Contains
...........................................
3
Operation
........................................................
3
System Verification Procedure
.....................................
3
MakingaCopyoftheMasterDataDisc
................................
3
Copying the Master Disc with an HP 9000 Series 200 or 300 Computer
....
4
ReplaceableParts
.................................................
4
Replacing the Master Disc
........................................
4
HP 85029B
7mm Verification Kit
i
Page 5
HP 85029B 7mm Verification Kit
Intended Uses
System
Verification.
Measuring the devices of this kit and comparing the results with supplied data
provides a tops-down verification of an HP
8753A/f3
with a 7 mm 50 ohm test set. The frequency range
covered by the HP 850298 is 300
kHz
to 6
GHz.
The system must be calibrated before performing a
system verification.
A tops-down verification is a procedure in which the devices in a verification kit are measured on the HP
8753A/B
system. These measured values are then compared with the NBS traceable data that
Hewlett-
Packard supplies with each verification kit. The HP 850298 verification kit contains three verification
devices for this purpose. The kit contains a 7 mm 20 dB attenuator, a 7 mm 50 dB attenuator, and a 7
mm mismatch attenuator. NBS traceable magnitude and phase data is provided with the HP 850298
verification kit at specific frequencies from 300
kHz
to 6
GHz
for all four S-parameters
The uncertainty limits provided with these verification devices is the worst case sum of the measurement uncertainties of the factory HP 850298 production test system plus the measurement uncertainties of the system being verified. If the measured data for the verification devices falls within the
supplied uncertainty limits, then the measurement system passes its performance verification.
Residual errors of the measurement system are, in part, due to the characteristics of the calibration
devices
used during system calibration. You should use the same calibration kit that will be
used when
calibrating the system for actual measurements. Using a different calibration kit can cause inconsistent
performance. Example: A user calibrates the system with a calibration kit that is in excellent condition
-
and the system passes the verification procedure easily. The system is then sent to production and is
calibrated using a worn or damaged calibration kit. In this case, the residual errors of the system could
fall outside the allowable uncertainty limits.
Each HP 850298 verification kit is measured at the factory in a tightly controlled environment using an
HP 8753. The test system is calibrated with special NBS-traceable standards, allowing the accuracy of
the test system to exceed that of a standard
HP 8753.
This system is verified daily, using a bottoms-up
procedure that quantifies individual sources of measurement error.
Refer to Table 1 to see which measurements are the basis for system verification.
Table 1. Measurements Used for System Verification
Sl
1
IS22
Sl2lS21
Verification Device
Magnitude
Phase
Magnitude
Phase
20
dB
attenuator
X X
X
60
dB
attenuator
X
X
mismatch attenuator
X
X
i
HP 85029B
7mm Verification Kit
1
Page 6
PASS/FAIL information is displayed only for the most useful measurements, as indicated in Table 1.
However, all four S-parameters are measured. Additionally, the uncertainties calculated for each
device are included in printed form.
Statistical Quality Control of Instrument Performance.
The HP 850298 allows the user to periodically record measured data. This history data is useful for statistical quality control of instrument
performance. Also, unusual deviations from historical data can warn the operator of possible degradation in instrument or verification kit performance.
Applicable Systems
The HP 850298 7 mm verification kit has been designed to check the performance of the
fOlIOWing
systems:
l
HP 8753A with HP 85046A test set
l
HP 87538 with HP 85044A or 85046A test set.
l
HP 87538 Option 006 with HP 85047A test set.
RECOMMENDED PRACTICES
To maintain optimum performance from this verification kit, observe these simple precautions:
Always place the verification devices back in the protective case between uses.
Make connections carefully to avoid misalignment, leading to inaccurate measurements or con-
nector damage.
Keep the connectors free of dirt and metallic particles.
If you must clean the connectors, use clean compressed air first. NEVER use abrasives. When
cleaning connectors, use liquid Freon exclusively and apply with a plastic swab. For more information, refer to the Microwave Connector Care Manual (HP part number 08510-90064) or application
note 326,
Principles of Microwave Connector Care
(literature number 5954-1566).
7 mm center conductor recession (without
collet)
must be 0.0 to 0.002 inches (0.0 to 0.051 mm).
RECOMMENDED DISC DRIVE AND PRINTERS
Disc Drive: HP 9122
Printers:
HP
2225A, 9876A, 2673A,
or 82906A
2
7mm Verification Kit
HP 85029B
Page 7
GENERAL INFORMATION
Weight
Net: 0.9 kg (2 lb)
Shipping: 1.4 kg (3 lb)
Recommended Recertification Period
Hewlett-Packard recommends that the verification kit be recertified annually; contact your local
Hewlett-Packard sales and service office for details.
What this Kit Contains
Verification Devices
-
The kit contains precision standard devices. The storage case is supplied to
protect the devices from damage that will degrade accuracy. Place the devices in the case immediately
after use.
Measured Data and Uncertainty Limits
-
is supplied both on disc and hard copy.
System Verification Procedure
The system verification procedure is located in the on-site system service manual for the HP 8753A or
87538.
l
In the HP
8753A
Network
Analyzer On-Sire
System Service Manual
(HP part number
08753-90022)
the system verification procedure is located behind the System Verification tab.
l
In the
HP
8753A/B
Network Analyzer HP 8702 Lightwave Component Analyzer On-Sire System
Service Manual
(HP part number
08753-90123),
the system verification procedure is located behind
the On-Site Verification tab.
MAKING A COPY OF THE MASTER DATA DISC
This disc contains data files which are unique to the verification standards shipped with your HP
850298 verification kit. Hewlett-Packard recommends that you make a copy of the master data disc for
everyday use, and store the master disc in a safe place.
Making a backup disc using the HP
8753A/B
is time consuming, as many files must be copied
individually. In addition, the files applicable to the HP 87538 can only be copied using an HP 87538, and
files applicable to the HP 8753A can only be copied using an HP 8753A.
A much faster way to make a backup copy is by using an HP 9000 Series 200 or 300 computer with an
HP 9122 disc drive.
7mm Verification Kit
3
Page 8
Copying the Master Disc with an HP 9000 Series 200 or 300 Computer
1.
Insert a blank disc into drive 1 of the HP 9000 series 200 or 300 computer and initialize it with the
command:
INITIALIZE
“:,700,1”,7
3.
Write-protect the master disc and insert it into drive 0 of the HP 9000 series 200 or 300 computer.
4.
Copy the files using the computer command:
COPY “:,700,0” TO
“:,700,1”
Put the master in a clean safe place, away from exposure to dust, sunlight, humidity, or magnetic fields.
REPLACEABLEPARTS
The three attenuators are separately available and should be ordered by the numbers given below.
Each of these devices has a serial number and the kit has a serial number. All four serial numbers
appear on the verification disc label.
Description
7
mm mismatch attenuator
7 mm 20 dB attenuator
7 mm 50 dB attenuator
Operating and service manual
Instrument case
Foam pads
l
ReDlacement
Dart number, includes disc with device-specific data
HP Part Number
85029-60004’
85029-60005’
85029-60006*
85029-90010
85029-80010
85029-80007
Replacing the Master Disc
The HP 850298 master disc contains unique data that applies to the individual verification devices. No
two devices have the same performance data. It is not a trivial matter to replace a lost or damaged
master disc, so it is important to make one or more backup copies of the Master Disc.
If your master data disc is lost or damaged, and you have no backup copies, take one of the following
actions:
If Recertification is Not Required in the Near Future.
Contact your nearest Hewlett-Packard service
office for a replacement. Please specify the serial number of the verification kit, and whether or not it
has ever been recertified. If a recertification has been performed, please indicate which service office
performed it.
If Recertification Will Be Required Soon.
Hewlett-Packard recommends that you have the verifica-
tion kit recertified early. A new master disc will be generated during the recertification process.
4
7mm Verification Kit
HP 850298
Page 9
REGIONAL SALES AND SUPPORT OFFICES
_
For information relating to Sales or Support of Hewlett-Packard products first contact your local Hewlett-Packard
office listed in the white pages of your telephone directory. If none is listed locally, contact one of the addresses listed
below lo obtain the address or phone number of the Hewlett-Packard
Sales
or Support office nearest you.
ASIA
Hewlett-Packard Asia Ltd.
47/F, 26 Harbour Road,
Wanchai, HONG KONG
G.P.O. Box 863, Hong Kong
Tel: (852)
5-8330833
Telex: 76793 HPA HX
Cable:
HPASIAL
TD
AUSTRALASIA
Hewlett-Packard Australia Ltd.
31-41 Joseph Street
BLACKBURN, Victoria 3130
Australia
Tel: (61) 8952895
Telex: 31-024
Cable: HEWPARD Melbourne
CANADA
Hewlett-Packard (Canada) Ltd.
6877 Goreway Drive
MISSISSAUGA, Ontario
L4V lM8
Tel: (416) 678-9430
Telex:
069-8644
JAPAN
Yokogawa-Hewlett-Packard Ltd.
29-21 Takaido-Higashi, 3 Chome
Suginami-ku TOKYO 168
Tel: 03 (331) 6111
Telex: 232-2024 YHPTOK
MEDITERRANEAN AND
MIDDLE EAST
Hewlett-Packard S.A.
Mediterranean and Middle East
Operations
Atrina Centre
32 Kifissias Avenue
Paradissos-Amarousion, ATHENS
Greece
Tel: (30) 682 88 11
Telex: 21-6588 HPAT GR
Cable: HEWPACKSA Athens
February, 1986
BENELUX 81 SCANDINAVIA
Hewlett-Packard S.A.
Uilenstede 475
P.O. Box 999
NL-1183 AG AMSTELVEEN
The Netherlands
Tel: (31) 20/43 77 71
Telex: 18 919 hpner nl
SOUTH & EAST EUROPE,
AFRICA
Hewlett-Packard S.A.
7, rue du Bois-du-Lan
CH-1217 MEYRIN 2, Geneva
Switzerland
Tel: (41) 22/83 12 12
Telex: 27835 hmea
Cable: HEWPACKSA Geneve
FRANCE
Hewlett-Packard France
Part d’activites
du Bois Briard
2, avenue du Lac
91040 EVRY Cedex
Tel: 1
61077
83 83
Telex: 6923
15F
GERMAN FEDERAL
REPUBLIC
Hewlett-Packard
GmbH
Hewlett-Packard-Strasse
Postfach 1641
D-6380 BAD HOMBURG
West Germany
Tel: 06172/400-O
Telex: 410 844 hpbhg
ITALY
Hewlett-Packard ltaliana
S.p.A.
Via G. Di Vittorio 9
l-20063 CERNUSCO SUL
NAVIGLIO
(Milano)
Tel: 02/92 36 91
Telex: 334632
UNITED KINGDOM
Hewlett-Packard Ltd.
King Street Lane
Winnersh,
WOKINGHAM
Berkshire
RGll
5AR
Tel: 734/78 47 74
Telex: 847178
EASTERNUSA
Hewlett-Packard Co.
4 Choke Cherry Road
ROCKVILLE, MD 20850
Tel: (301) 670-4300
MIDWESTERN USA
Hewlett-Packard Co.
5201
Tollview
Drive
ROLLING MEADOWS, IL 60008
Tel: (312) 2559800
SOUTHERN USA
Hewlett-Packard Co.
2000 South Park Place
P.O. Box 105005
ATLANTA, GA 30348
Tel: (404) 955-l 500
WESTERN USA
Hewlett-Packard Co.
5161 Lankershim Blvd.
P.O. Box 3919
NO. HOLLYWOOD, CA 91609
Tel: (818) 506-3700
OTHER INTERNATIONAL
AREAS
Hewlett-Packard Co.
Intercontinental Headquarters
3495 Deer Creek Road
PALO ALTO, CA 94304
Tel: (415)
857-1501
Telex:
034-8300
Cable:
HEWPACK
Page 10
HP Part No. 85029-90010
Printed JULY 1988
HEWLETT
PACKARD
Printed in U.S.A.
Loading...